BootLoader - P970 RECOVERY - LG Optimus Black

When you update the firmware on the LG P-970 process generated an error.
The service center said that Booth killed Loader.
The phone does not respond to any button presses, connect the power supply and are not connected to the computer.
S/W updater not work.
phone will not turn on at all.
Please help with posstanovleniem Boot loader phone.
Apologies for the curve English.

Metallurg.IT said:
When you update the firmware on the LG P-970 process generated an error.
The service center said that Booth killed Loader.
The phone does not respond to any button presses, connect the power supply and are not connected to the computer.
S/W updater not work.
phone will not turn on at all.
Please help with posstanovleniem Boot loader phone.
Apologies for the curve English.
Click to expand...
Click to collapse
Sorry but what?

Metallurg.IT said:
When you update the firmware on the LG P-970 process generated an error.
The service center said that Booth killed Loader.
The phone does not respond to any button presses, connect the power supply and are not connected to the computer.
S/W updater not work.
phone will not turn on at all.
Please help with posstanovleniem Boot loader phone.
Apologies for the curve English.
Click to expand...
Click to collapse
Hello
Just to make sure you did plug it in with battery out and volume up button pressed?
If you did and it still doesn't work then your x-loader and U-boot is definitely fried.
Then we can confirm that SW Update is done from already working U-boot (We are trying to modify the KU5900 V30 to fit our phone but we needed to make modifications to U-boot and we too afraid to test because of this.)
If you plug your phone in does your computer detect it at all? (If your computer is running Linux then there's nothing anyone can do short of opening up the device and re-flash the flash memory using specialized tools. Well that's the conclusion I drew when scouring the internet a few days now in search of a method to revive a boot-loader-less Optimus.)
If your computer detects anything then you can save your phone.
You said that the service-centre said that the boot-loader is gone. Did they refuse to fix it?
I'm going to keep on searching to find a way to fix it from shot boot-loader so that we can start working in modified U-boot and of course now to help you too.
Hope you get your phone fixed.
Good Luck

Code:
Phone is not connected to the computer.
On pressing the button does not respond.
The charger starts to charge the battery.
Dealer refused to repair, as the phone was purchased in Germany and I was in Russia.
In general, what should I do? Point the blind on the themes of repair or tell what to expect?

Metallurg.IT said:
Code:
Phone is not connected to the computer.
On pressing the button does not respond.
The charger starts to charge the battery.
Dealer refused to repair, as the phone was purchased in Germany and I was in Russia.
In general, what should I do? Point the blind on the themes of repair or tell what to expect?
Click to expand...
Click to collapse
If it start to charge then it's good , it lives!
OMAP chips follow this boot process :
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
Your ROM is fine since it Read Only
Instead of booting from the Flash Memory in the phone (which doesn't work in your case) I have been looking into the possibility of booting from SD Card. Easy to fix if something goes wrong and doesn't do anything to the device itself. In your case if you can boot from SD Card then you can restore your first few partitions and have SW Update Working again and recover from there.
The Rom supposedly looks for boot devices in the Following Order :
Seral -> SD -> Nand
Booting from Serial is nearly impossible since we can't make a proper connection to the phone without U-boot already set up. LG probably did it on purpose.
Booting from SD is the next thing. I only recently came onto the idea and I still have to figure out how I am going to approach this.
LG has the power to change the ROM so it might not be possible to do this. I will post again as soon as I find out what order our device looks for boot devices.
Good Luck in your efforts.

Metallurg.IT said:
When you update the firmware on the LG P-970 process generated an error.
The service center said that Booth killed Loader.
The phone does not respond to any button presses, connect the power supply and are not connected to the computer.
S/W updater not work.
phone will not turn on at all.
Please help with posstanovleniem Boot loader phone.
Apologies for the curve English.
Click to expand...
Click to collapse
How did you come to this failure? As I read, there was an error updating the firmware.
Give us a background. What firmware did you flash? KDZ or BIN? Did you modify anything?
Must try bringing up S/W Updater mode. Insert USB and press volume up for few seconds and don't release.

Hmm, maybe wrong ROM flashed? Then it would be changed anything related with x-loader and u-boot...
But when looking this,
Metallurg.IT said:
Code:
Phone is not connected to the computer.
On pressing the button does not respond.
The charger starts to charge the battery.
Click to expand...
Click to collapse
If plugging charger would shows charging battery indicator, then bootloader is fine...

redy2006 said:
Hmm, maybe wrong ROM flashed? Then it would be changed anything related with x-loader and u-boot...
But when looking this,
If plugging charger would shows charging battery indicator, then bootloader is fine...
Click to expand...
Click to collapse
Yep. Might want to rest it for several minutes, or hours. Remove battery and let it sit for a while. Then try again booting in S/W update. Volume up (+) first and then insert USB.

Connecting the charger is not indicating the display screen.
NOT S/W repair.
after a failed firmware - Display never light up.
Read about boot from a flash card, please give more files or describe a way to restore the phone
Code:
Killed when flash a phone through ---- SmartFlashTool_External
Strip installation stopped and became red.
A picture ((( S/W Upgrade )))hanging on the phone and the phone did not answer one pressing than taking out the battery.
Tried to connect the phone to the computer, nothing happens, the new device is not connected to the computer

Metallurg.IT said:
Connecting the charger is not indicating the display screen.
NOT S/W repair.
after a failed firmware - Display never light up.
Read about boot from a flash card, please give more files or describe a way to restore the phone
Code:
Killed when flash a phone through ---- SmartFlashTool_External
Strip installation stopped and became red.
A picture ((( S/W Upgrade )))hanging on the phone and the phone did not answer one pressing than taking out the battery.
Tried to connect the phone to the computer, nothing happens, the new device is not connected to the computer
Click to expand...
Click to collapse
I haven't been able to tale the idea of booting from SD any further, because I have been really busy, sorry. I will have time over the weekend.
Sent from my LG Optimus Black

xonar_ said:
I haven't been able to tale the idea of booting from SD any further, because I have been really busy, sorry. I will have time over the weekend.
Sent from my LG Optimus Black
Click to expand...
Click to collapse
Well, I'm waiting your public response. thanks

Metallurg.IT said:
Well, I'm waiting your public response. thanks
Click to expand...
Click to collapse
I ran some tests today and they were not so informative. Afterwards I found out that the X-loader I used looks for U-boot from the onboard storage first so it might have worked but just loaded U-boot from normal storage and continued as if nothing funny happened.
I'll keep you posted.
Sent from my LG Optimus Black

xonar_ said:
I ran some tests today and they were not so informative. Afterwards I found out that the X-loader I used looks for U-boot from the onboard storage first so it might have worked but just loaded U-boot from normal storage and continued as if nothing funny happened.
I'll keep you posted.
Sent from my LG Optimus Black
Click to expand...
Click to collapse
Thanks for your support, I will be waiting for your answers.

Good news! Our Device Supports Booting from SD
I recently figured out that we have a internal sd the is booted from, I always though it was NAND.:silly:
I'll have a test for you to run in a few days, maybe less. I don't expect much more than the LG logo to show, but thats more than what you got, right .

xonar_ said:
Good news! Our Device Supports Booting from SD
I recently figured out that we have a internal sd the is booted from, I always though it was NAND.:silly:
I'll have a test for you to run in a few days, maybe less. I don't expect much more than the LG logo to show, but thats more than what you got, right .
Click to expand...
Click to collapse
Quickly would you write a manual restore my phone

Metallurg.IT said:
Quickly would you write a manual restore my phone
Click to expand...
Click to collapse
I haven't been able to get a working solution. (I think mine stops when finding working X-loader from device itself then continueing)
I don't have time this very instant to write how I make (supposedly) bootable SD. I won't have time tomorow either, unfortunately. I should have time over the weekend.
Do you have a linux machine availiable? I don't know of a way to do it in Windows or OSX.
This is still a long shot by any chance. You should look into the possibilaty of taking your phone to a cellphone repair shop (Not your service provider a proper cellphone repair shop). It might cost a bit, but it will make your phone work again.

xonar_ said:
I haven't been able to get a working solution. (I think mine stops when finding working X-loader from device itself then continueing)
I don't have time this very instant to write how I make (supposedly) bootable SD. I won't have time tomorow either, unfortunately. I should have time over the weekend.
Do you have a linux machine availiable? I don't know of a way to do it in Windows or OSX.
This is still a long shot by any chance. You should look into the possibilaty of taking your phone to a cellphone repair shop (Not your service provider a proper cellphone repair shop). It might cost a bit, but it will make your phone work again.
Click to expand...
Click to collapse
Yes, I have a Linux OS. (Gentoo / CentOS / Ubuntu )

Bricked P970 stuck at LG logo
Hi, I have a P970h which had Huexxx's Zeus 7.0 ROM and I sent CWM to do a backup of the ROM's current state. I continued to work but then I realized the phone was still sitting in th LG logo after quite a while. I dindn't know Zeus had the option to go into recovery by pressing a physical key (G button) multiple times while starting boot and I got into CWM recovery thinking I had pressed a key combination. I was able to wipe the cache and the phone booted normally but as I didn't have the battery in the phone as it was booting when I put the battery and unplugged the phone from USB it still showed as if I had full battery, so I sent the phone to reboot.
From that moment on I wasn't able to find the "key combination" that got me into CWM recovery and I flashed the stock ROM to send it to warranty to my local carrier. They weren't able to get it passed the LG logo and told me that it was due to the phone being dropped as it was showing a little bump on one of the corners of the battery cover and told me that because of that bump the warranty was void.
I have tried to get it out of the bricked state via SMARTFLASH, LG Mobile Support Tool, KDZ_FW_UPD, using the stock KDZ file for my device, injecting CWM and so on, but I'm still staring at the LG logo. I'm able to get into S/W Upgrade mode at any time, and the problem presented is the typical brick with the LG logo showing and the action keys smoothly and repeteadly going on and off.
I'm not new at using ROMS but it's the first time this happens to me and I'm sure if I'm able to go into fastboot or recovery I'll be able to unbrick the device, the first thing that comes out of my mind is if it is possible to reverse engineer a flasheable ZIP file with Zeus ROM so I can access CWM recovery into a KDZ file but I don't think that's possible.
What do you think I can do in this case? Should I feel hopeless?

wollernic said:
Hi, I have a P970h which had Huexxx's Zeus 7.0 ROM and I sent CWM to do a backup of the ROM's current state. I continued to work but then I realized the phone was still sitting in th LG logo after quite a while. I dindn't know Zeus had the option to go into recovery by pressing a physical key (G button) multiple times while starting boot and I got into CWM recovery thinking I had pressed a key combination. I was able to wipe the cache and the phone booted normally but as I didn't have the battery in the phone as it was booting when I put the battery and unplugged the phone from USB it still showed as if I had full battery, so I sent the phone to reboot.
From that moment on I wasn't able to find the "key combination" that got me into CWM recovery and I flashed the stock ROM to send it to warranty to my local carrier. They weren't able to get it passed the LG logo and told me that it was due to the phone being dropped as it was showing a little bump on one of the corners of the battery cover and told me that because of that bump the warranty was void.
I have tried to get it out of the bricked state via SMARTFLASH, LG Mobile Support Tool, KDZ_FW_UPD, using the stock KDZ file for my device, injecting CWM and so on, but I'm still staring at the LG logo. I'm able to get into S/W Upgrade mode at any time, and the problem presented is the typical brick with the LG logo showing and the action keys smoothly and repeteadly going on and off.
I'm not new at using ROMS but it's the first time this happens to me and I'm sure if I'm able to go into fastboot or recovery I'll be able to unbrick the device, the first thing that comes out of my mind is if it is possible to reverse engineer a flasheable ZIP file with Zeus ROM so I can access CWM recovery into a KDZ file but I don't think that's possible.
What do you think I can do in this case? Should I feel hopeless?
Click to expand...
Click to collapse
Your bootloader is fine. If you can go to SW Update mode and device is pysically OK, then you can easily recover. Go to SW Update and follow recovery procedure using SFT. If that doesn't work (asuming you did it right) then your device is physically broken.

xonar_ said:
Your bootloader is fine. If you can go to SW Update mode and device is pysically OK, then you can easily recover. Go to SW Update and follow recovery procedure using SFT. If that doesn't work (asuming you did it right) then your device is physically broken.
Click to expand...
Click to collapse
I have done the SFT procedure propperly, if I'm not mistaken, that's the tool I initially used to root the device, I have tried the stock KDZ file, converted to BIN and FLS and a couple of BIN and FLS packs posted here at XDA but haven't been able to get it to work. I have only dropped my device twice, once without silicon case and the other with silicon protection, both times the height of the fall was minimal and they were far back from the moment the phone bricked.
After my first attempt to unbrick via SFT I started thinking this was a faulty device and it was a fail waiting to happen since shipped from factory and that's the reason why I sent it to warranty claim. Thanks anyway...

Related

[Q] Help me pls.. I think I've really bricked my P990

Hi all kind bros and sis,
Please help me out as I think I've really bricked my less than 2 months brand new Optimus 2X..
You see.. I rooted my P990 using unlock root and chanced upon CM7 and thought of giving it a try. I installed clockworkmod and downloaded the stable release of 7.1 for Optimus 2x.. following the instruction to do a Nandroid backup and proceeded with the Mod..
Not knowing that I need to wipe everything including data.. I just selected the Dalvik cache wipe and proceed with the mod. The process went for more than 15mins and I saw some graphics (the android figure going round and round) but it just stuck there... the screen went blank and when I touched those home or back buttons.. they will lighted but nothing happens. I can't power it off also. So I manually took out the battery and put it back before powering up again. The android picture appeared again briefly for about 1 min and just hanged there. I took out the battery again and this time it was dead.. no matter what I press : vol + and power buttons together; home+Vol+ + power down; Vol- + power down.. all those do not revive the phone.
I tried taking out the external SD card and try powering up. The LG logo appeared and got stuck there.
I searched on Google and found the smartflashtool. I tried that and managed to install the NVidia boot recovery driver and stuff correct. Hold the vol+ button and power key before plugging in but the smarttool did not find the com port or communication driver whatever so I couldn't flash it back to stock.
I'm very desperate and stuck now... did I just accidentally burned the board or something? What bad luck I have
If that's the case, will I still be able to bring the phone back to LG service centre and get it repaired?
Please help me.. any kind souls out there. I really liked the phone and hoped to bring it back. else it's such a shortlived phone... really breaks my heart to see this..
Thanks in advance...
humblepie88 said:
Hi all kind bros and sis,
Please help me out as I think I've really bricked my less than 2 months brand new Optimus 2X..
You see.. I rooted my P990 using unlock root and chanced upon CM7 and thought of giving it a try. I installed clockworkmod and downloaded the stable release of 7.1 for Optimus 2x.. following the instruction to do a Nandroid backup and proceeded with the Mod..
Not knowing that I need to wipe everything including data.. I just selected the Dalvik cache wipe and proceed with the mod. The process went for more than 15mins and I saw some graphics (the android figure going round and round) but it just stuck there... the screen went blank and when I touched those home or back buttons.. they will lighted but nothing happens. I can't power it off also. So I manually took out the battery and put it back before powering up again. The android picture appeared again briefly for about 1 min and just hanged there. I took out the battery again and this time it was dead.. no matter what I press : vol + and power buttons together; home+Vol+ + power down; Vol- + power down.. all those do not revive the phone.
I tried taking out the external SD card and try powering up. The LG logo appeared and got stuck there.
I searched on Google and found the smartflashtool. I tried that and managed to install the NVidia boot recovery driver and stuff correct. Hold the vol+ button and power key before plugging in but the smarttool did not find the com port or communication driver whatever so I couldn't flash it back to stock.
I'm very desperate and stuck now... did I just accidentally burned the board or something? What bad luck I have
If that's the case, will I still be able to bring the phone back to LG service centre and get it repaired?
Please help me.. any kind souls out there. I really liked the phone and hoped to bring it back. else it's such a shortlived phone... really breaks my heart to see this..
Thanks in advance...
Click to expand...
Click to collapse
Try using SmartFlashTool, download the LG stock ROM (can be found here in XDA forum, i'll help you find the link), flash the .bin and .fls files.
humblepie88 said:
Please help me out as I think I've really bricked my less than 2 months brand new Optimus 2X..
...
"Hold the vol+ button and power key before plugging in but the smarttool did not find the com port..."
Click to expand...
Click to collapse
Turn off the phone. Hold Vol-DOWN while plugging it in. Start Smartflash and see the com-ports magically appear.
Follow trymhansen's instructions. He helped me before with my softbricked phone.
I hope you get your O2X back to life! Keep us posted
Best of luck to you!
PS. I also believe you should pull out the battery after turning off the phone in Trym's instructions. Trym correct me if I'm wrong please.
Hi All,
Thanks for your kind replies. I did follow your instruction. Take out the battery (I removed the ext SDcard as well), press and hold -vol and plug in the phone via USB. Afterwhich start up smartflash tool.. still nothing happens and no com ports are found.. The version of smartflashtool that I used is Dec 2010. Do I need to get the latest one and also the LG united drivers installed?
I also tried starting smartflash tool before the sequence.. still the same. BTW.. my OS is Win 7. Is it supported?
Really at my end's wit. Hope I can bring my phone back to life soon and I'm not really bricking it. I heard Samsung phones are not that easy to brick and can get to the recovery mode pretty easily. is it true?
Please help me.. thanks
Hi bros,
Attached are my screenshots from the device manager and smartflash tool... both seems not able to find the phone and allocate a com port. I've tried installing the latest LG mobile driver 3.6 but no help as well
Have you followed instructions as described here http://forum.xda-developers.com/showthread.php?t=1008070 ?
Also, try to attach your phone directly to computer, using usb ports from computer mainboard. I have experienced problems when attaching it via extension usb cord or attaching it to computer case ports. (I hope that you can understand what I have mean to say with usb )
Hi Memhis,
Yes.. I followed exactly the instructions from the thread and I've plugged into a USB port directly to the computer which is one of the ports in front.. not via any extension or USB hub.. still it did not detect.
I'll try to use another computer which is running Win XP and try again. I've downloaded those 3 files from that thread you recommended try using those instead.. hope it can be detected this time else I think I'll have to send to LG service for repair tomorrow.
I've been jailbreaking and modding my Iphone a lot and everytime whenever there's a near brick situation.. I'm able to fix it but not this time with an Android or LG perhaps... I hope I don't have to go to the extend of using ADB low level to push some files which I saw in one of the thread that one of the guys did that.. but I doubt I can since my windows can't even detect the phone!!
Maybe this will be my first and last LG phone if I ever get it repaired...
humblepie88 said:
Hi Memhis,
Yes.. I followed exactly the instructions from the thread and I've plugged into a USB port directly to the computer which is one of the ports in front.. not via any extension or USB hub.. still it did not detect.
I'll try to use another computer which is running Win XP and try again. I've downloaded those 3 files from that thread you recommended try using those instead.. hope it can be detected this time else I think I'll have to send to LG service for repair tomorrow.
I've been jailbreaking and modding my Iphone a lot and everytime whenever there's a near brick situation.. I'm able to fix it but not this time with an Android or LG perhaps... I hope I don't have to go to the extend of using ADB low level to push some files which I saw in one of the thread that one of the guys did that.. but I doubt I can since my windows can't even detect the phone!!
Maybe this will be my first and last LG phone if I ever get it repaired...
Click to expand...
Click to collapse
launch smartflashtool first, extract the .fls and .bin files, hold down volume at the same time plug in the usb port to your comp. you must see a s/w updating logo in your phone's screen and smartflash should detect your phone. then click start!
Sent using a phone.
Hi mrgian,
I just tried to revive my phone by using the same method on a different laptop running on Win XP.. plugged directly to a side USB port but still no luck. There's no s/w updating logo appearing on my phone and smartflashtool also failed to detect my phone. I've found another thread opened by another user and my situation is exactly the same as his :
http://forum.xda-developers.com/showthread.php?t=1161583
But lucky for him is that he's able to get it working after changing to another PC but I've tried 3 different machines and no luck so far...
I'll try to use the NVflash as a last resort and see if I've any luck with NVflash at all.. If it failed again.. I think I've no choice but to send it to the repair centre for servicing then..
humblepie88 said:
Hi mrgian,
I just tried to revive my phone by using the same method on a different laptop running on Win XP.. plugged directly to a side USB port but still no luck. There's no s/w updating logo appearing on my phone and smartflashtool also failed to detect my phone. I've found another thread opened by another user and my situation is exactly the same as his :
http://forum.xda-developers.com/showthread.php?t=1161583
But lucky for him is that he's able to get it working after changing to another PC but I've tried 3 different machines and no luck so far...
I'll try to use the NVflash as a last resort and see if I've any luck with NVflash at all.. If it failed again.. I think I've no choice but to send it to the repair centre for servicing then..
Click to expand...
Click to collapse
does the laptop have lg drivers installed?
Sent using a phone.
inflance hotota
mrgian said:
does the laptop have lg drivers installed?
Sent using a phone.
Click to expand...
Click to collapse
Yes.. I've installed the latest LG united mobile driver version 3.6. Any wrong with that version... Really don't know where / what is missing or my phone is really fried after just one mod attempt?
I've also tried NVflash and it's stuck at the "bootloader initialization" screen....
Nothing appeared on the phone... not even LG logo. Can't believe LG phones are so fragile and unmodifiable
humblepie88 said:
Yes.. I've installed the latest LG united mobile driver version 3.6. Any wrong with that version... Really don't know where / what is missing or my phone is really fried after just one mod attempt?
I've also tried NVflash and it's stuck at the "bootloader initialization" screen....
Nothing appeared on the phone... not even LG logo. Can't believe LG phones are so fragile and unmodifiable
Click to expand...
Click to collapse
can you entet CWM? Press volume down til s/w will appear.
Sent using a phone.
try to charge the battery first...power off your device and charge it...maybe leave it charging for about 1hr even if you dont see anything on the screen( i believe after plugin the charger you will see the charging logo but it will disapear after a few seconds)...after 1 hr unplug and try to check if it will boot to clockwork recovery...if yes then just do complete data wipe...also try installing the ext3 back.zip, it will help delete system files(sometimes CWR is not deleting this)...hope this help
chupi_24 said:
try to charge the battery first...power off your device and charge it...maybe leave it charging for about 1hr even if you dont see anything on the screen( i believe after plugin the charger you will see the charging logo but it will disapear after a few seconds)...after 1 hr unplug and try to check if it will boot to clockwork recovery...if yes then just do complete data wipe...also try installing the ext3 back.zip, it will help delete system files(sometimes CWR is not deleting this)...hope this help
Click to expand...
Click to collapse
you got a point there.
Sent using a phone.
humblepie88 said:
Yes.. I followed exactly the instructions from the thread and I've plugged into a USB port directly to the computer which is one of the ports in front.. not via any extension or USB hub.. still it did not detect.
Click to expand...
Click to collapse
When you say an USB port in the front do you mean an USB in the back? Because the ones in front are the case ones, the ones in the back are the good ones, i.e. the ones that are directly attached to the mobo.
LarsPT said:
When you say an USB port in the front do you mean an USB in the back? Because the ones in front are the case ones, the ones in the back are the good ones, i.e. the ones that are directly attached to the mobo.
Click to expand...
Click to collapse
I've tried the recovery via 2 diff laptops and plugging in directly to one of the side USB ports but to no avail as well.. I think I've plugged in the phone correctly but there's no reaction at all/
mrgian said:
can you entet CWM? Press volume down til s/w will appear.
Sent using a phone.
Click to expand...
Click to collapse
How to enter CWM? I can't even power up the phone and no reaction at all when plugged into USB via smartflash.. the screen remains black. It's liked the whole phone is burned or something... but strange thing is that it can detect APX and asked to install drivers... but after successfully installing the Nvidia boot recovery driver.. the com ports does not get discovered.. What is wrong?
chupi_24 said:
try to charge the battery first...power off your device and charge it...maybe leave it charging for about 1hr even if you dont see anything on the screen( i believe after plugin the charger you will see the charging logo but it will disapear after a few seconds)...after 1 hr unplug and try to check if it will boot to clockwork recovery...if yes then just do complete data wipe...also try installing the ext3 back.zip, it will help delete system files(sometimes CWR is not deleting this)...hope this help
Click to expand...
Click to collapse
I plugged in the phone with battery but there was no charge logo or whatever.. the screen remains blank.. I'll try to leave it charging and see what happens. But I've remembered there was still about 80% power when this disaster happened and I've taken out the battery since.. so the charge should have remain? Btw.. where can I get this ext3 back.zip and how to use it? thanks

[Q] Bricked ! nvflash not work.

Need help.
My optimus 2x seem to be bricked.
nothing shown at the screen. (just blank)
i can't enter the cwm.
smartflash also cannot detect my phone.
I try to use nvflash but it stuck at "waiting for bootloader to initialize"
anything i can do to revive my phone ?
or is it totally bricked ?
Hi,
Congratz for being the first person I ever read on o2x thread whom actually 'succesfully' bricked his phone. I've been here since o2x thread was born..alot of ppl use the term 'bricked' loosely but hasn't actually really bricked their phones.
If you lost ADB, Fastboot, unable to Nvflash/Smartflash... your phone is, sad to say, gone.
Anyway, I really hope you can share what you did to eventually get into this state, atleast you can help others to prevent bricking their o2x.
Thanks.
Well congratz, now move to something that is properly supported
Sent from my Optimus 2X using XDA
Haha.
can I get medal for this "achievement" ?
I bought it as faulty phone around usd 16. so I don't know what happen to it.
Ouh...usd16.. pretty useful for spare parts.
If you bought it for 16 dollars then I would advise you to sell the phone for spare parts. Even the glass costs 20 or more dollars.
Sent from my Optimus 2X using XDA
hmmmm, dudes, idk if im right buuuuuuuuuut... happened to me, i thought it was completelt dead, when after all i found out that my pc didnt recognise my lg o2x as an apx platform so it would always fail, sooooo, i did it on my sisters pc which never had lg drivers and i resurected my phone id advise to try it...
---------- Post added at 11:38 PM ---------- Previous post was at 11:35 PM ----------
ohhh, long story short and translated, if you have ever installed lg drivers on your pc, forget about it being recognised as an apx platform, even if you uninstall all lg software
1.From PC,manually place Stock LG Rom(V20Q.zip or [?]) on Your SD card then reinsert in phone.
2.Don't connect phone to PC or power (AC)
3.pull the battery out and reinsert it( now connect power (AC)
Hold the Volume Down button (keep pressed!!) then press and hold the Power button until the device turns on and you see the recovery menu
4.then proceed as you normally would meaning install .zip from SD card
Hope it helps
-JAZZMAN- said:
1.From PC,manually place Stock LG Rom(V20Q.zip or [?]) on Your SD card then reinsert in phone.
2. pull the battery out and reinsert it
Hold the Volume Down button
(keep pressed!!) then press and hold the Power down button until the device turns on and you see the recovery menu
3.then proceed as you normally would meaning install .zip from SD card
Hope it helps
Click to expand...
Click to collapse
dude O_O
he said the phone wont even load recovery O_O
skylinegt77 said:
dude O_O
he said the phone wont even load recovery O_O
Click to expand...
Click to collapse
Yes,I read that, But neither would mine after using ext3 converter without backup!
So after eating a big bowl of "BOOTLOOPS" I utilized the phones hard reset mode thinking It would lead to a factory reset but instead got the CWM recovery menu
after which I flashed and Voila 0_0
Also "DUDE" at least I'm trying to offer help instead of joking about such a serious concern...I guess... well only maybe when it's your phone and you have no answers<---this looks better
-JAZZMAN- said:
Yes,I read that, But neither would mine after using ext3 converter without backup!
So after eating a big bowl of "BOOTLOOPS" I utilized the phones hard reset mode thinking It would lead to a factory reset but instead got the CWM recovery menu
after which I flashed and Voila 0_0
Also "DUDE" at least I'm trying to offer help instead of joking about such a serious concern...I guess... well only maybe when it's your phone and you have no answers<---this looks better
Click to expand...
Click to collapse
You should really read again OP, it can't load bootloader.. So it can't boot to anything as bootloader is the essential part of the phone that loads after either recovery partition, or /boot Android one.
aris.syah said:
Need help.
My optimus 2x seem to be bricked.
nothing shown at the screen. (just blank)
i can't enter the cwm.
smartflash also cannot detect my phone.
I try to use nvflash but it stuck at "waiting for bootloader to initialize"
anything i can do to revive my phone ?
or is it totally bricked ?
Click to expand...
Click to collapse
Just to check: are you sure to boot the phone in Apx mode? Battery off, volume up pressed, then plug AC ?
Striatum_bdr said:
You should really read again OP, it can't load bootloader.. So it can't boot to anything as bootloader is the essential part of the phone that loads after either recovery partition, or /boot Android one.
Click to expand...
Click to collapse
Once again, I know and understand!!!!!
New to LG but not to how this process works so please stop with the "Dear N00B"
responses
I was only offering a suggestion that maybe wasn't tried even if proven futile!
also, for the most part, the days of "bricks" are pretty much over so there is always the slimmest possibility for hope. Wouldn't you exhaust every possibility....
Anyway,enough said on this I hope that he finds a solution
hi there,
N00B here...i had this kind of problem too...my laptop still recognize it as nvidia bootloader for mobile device AKA APX driver, but it never flashed in the nvflash way...
holding volume down and insert charging cord also give me nothing...

There must be hope for my 2x that just kinda bricked.

Okay. I really don't feel comfortable trying new stuff without searching everything about it, so I must say I was pretty informed on flashing a new ROM on my 2x.
So I downloaded Rom Manager and flashed Clockworkmod Recovery. Every tutorial I read said I needed to backup my ROM. Also, they said I had to back it up manually, by booting into system recovery, pressing volume down + power, and I kinda ignored that.
I saw the option "Back up existing ROM" or something like that on ROM Manager, so I tried that. My phone rebooted, shown the LG logo, and then it went black and freezed. You can tell the phone is on because the screen stays black, but you can see some backlight. Also, the settings, home, back and search buttons are lit up.
I have to remove the battery to turn it off. I tried booting into recovery with the vol. down + power (I even tried vol. up... and both up and down + power) but it keeps giving me the black screen.
I looked up on the internet to see if someone had the same problem... no one had, apparently.
Sooooo I decided it was time to ask in a forum. Please try to help me, I need my phone working as soon as possible and sorry for my bad english
HeadbangerHS said:
Okay. I really don't feel comfortable trying new stuff without searching everything about it, so I must say I was pretty informed on flashing a new ROM on my 2x.
So I downloaded Rom Manager and flashed Clockworkmod Recovery. Every tutorial I read said I needed to backup my ROM. Also, they said I had to back it up manually, by booting into system recovery, pressing volume down + power, and I kinda ignored that.
I saw the option "Back up existing ROM" or something like that on ROM Manager, so I tried that. My phone rebooted, shown the LG logo, and then it went black and freezed. You can tell the phone is on because the screen stays black, but you can see some backlight. Also, the settings, home, back and search buttons are lit up.
I have to remove the battery to turn it off. I tried booting into recovery with the vol. down + power (I even tried vol. up... and both up and down + power) but it keeps giving me the black screen.
I looked up on the internet to see if someone had the same problem... no one had, apparently.
Sooooo I decided it was time to ask in a forum. Please try to help me, I need my phone working as soon as possible and sorry for my bad english
Click to expand...
Click to collapse
HeadbangerHS don't be disheartened.Here is a link below which will link u to Smartflash tool which will help you in flashing ur Optimus 2x back to life.Extreme caution is advised.Do at ur own risk.Not to be held responsible for bricking ur device.
http://forum.xda-developers.com/show....php?t=1008070
If u r unable to download smartflash firmware from the above link another link is attached below.Here u will be able to download firmware according to ur region.
http://forum.xda-developers.com/showthread.php?t=1035041
Note in smartflash tool u will have 2 options to select file.CP bin & AP bin.If u download firmware according to ur region u will have 2 files CP.fls and AP.bin.So CP.fls will go in CP.bin option and AP file in AP.bin option.You will have a factory installed device ( data in internal SD will be erased in the above procedure).
Hope this will help.Happy flashing and be careful to follow instructions:good:
arvindlakra,
just wanted to highlight that your first link gives an error....not able to check the right thread...so could not link the correct address....
thanks
I'll look this smartflash tool up on the internet. Too bad I still couldn't find the firmware for my region D:
SREEPRAJAY said:
arvindlakra,
just wanted to highlight that your first link gives an error....not able to check the right thread...so could not link the correct address....
thanks
Click to expand...
Click to collapse
Sreeprajay m8 sorry to create such a silly mistake.But second link sure had link to both firmware and Smartflash software.
Just wanted to help a friend in need that's it:laugh:.
can I use a firmware from another region?
Please specify ur current region.So could help u out in selecting a specific firmware m8.
I live in Brazil. Here, I just saw this post on the topic containing the firmwares:
will the original rom include baseband ?
Can we flash original rom to downgrade baseband ?
Click to expand...
Click to collapse
Yep, you can do it. Also you can flash open firmware with branded phone and all sh*t from brand will gone. You can flash your LGP990 with other country firmware to get other apps & languages.
Click to expand...
Click to collapse
Is this accurate?
HeadbangerHS said:
I live in Brazil. Here, I just saw this post on the topic containing the firmwares:
Is this accurate?
Click to expand...
Click to collapse
Yes it is accurate.I do live in India and use EURO OPEN v20q and some times CIS
BIN_LGP990AT-00-V20c-CIS-XXX-MAR-16-2012.Please do check if ur device is P990 or P990h.
thanks, you are helping me a lot.
Is there an easy way to know if it is a p990 or a p990h? I don't have the phone's box here :/
____________________________________________________________________________
EDIT:
I looked it up on the site where I bought my phone and I'm 80% sure it is a p990. Thanks anyway.
And dude, the firmware is pretty heavy...
HeadbangerHS said:
thanks, you are helping me a lot.
Is there an easy way to know if it is a p990 or a p990h? I don't have the phone's box here :/
Click to expand...
Click to collapse
Just simply remove the back cover and remove the battery.Below the battery will be printed details about ur phone.Mine is P990 made in Korea.
hey, it's been some time.
I found out my phone is actually a p990h and I just can't find the firmware for this model... would you mind helping me out some more?
I'm sorry but I really need my phone working before I can go on a trip on monday...
HeadbangerHS said:
hey, it's been some time.
I found out my phone is actually a p990h and I just can't find the firmware for this model... would you mind helping me out some more?
I'm sorry but I really need my phone working before I can go on a trip on monday...
Click to expand...
Click to collapse
It have been some time m8.Ok found a link for ur region firmware.But the file is in Kdz format.Link for the firmware is below:
http://lg-phone-firmware.com/index.php?id_mod=3
Tutorial for flashing the Kdz file can be found here:
http://forum.xda-developers.com/showthread.php?t=1264289
Plzzzz press Thanks button if it helped.
oh god. when rebooting in SW upgrade mode, the phone turns on, shows the lg logo, goes to the black screen and turns off. then it repeats forever... and doesn't show the SW upgrade screen. I'll try asking on the kdz tutorial topic, but if you or someone could help me before, it would be more than great...
__________________________________________________________________________________________________
EDIT:
yeah, I can't post there due to being a junior member.
HeadbangerHS said:
oh god. when rebooting in SW upgrade mode, the phone turns on, shows the lg logo, goes to the black screen and turns off. then it repeats forever... and doesn't show the SW upgrade screen. I'll try asking on the kdz tutorial topic, but if you or someone could help me before, it would be more than great...
__________________________________________________________________________________________________
EDIT:
yeah, I can't post there due to being a junior member.
Click to expand...
Click to collapse
http://forum.xda-developers.com/showthread.php?t=1715272
HeadbangerHS said:
oh god. when rebooting in SW upgrade mode, the phone turns on, shows the lg logo, goes to the black screen and turns off. then it repeats forever... and doesn't show the SW upgrade screen. I'll try asking on the kdz tutorial topic, but if you or someone could help me before, it would be more than great...
__________________________________________________________________________________________________
EDIT:
yeah, I can't post there due to being a junior member.
Click to expand...
Click to collapse
Did the flashing of kdz file completed and after that reboots occure.If yes then unplug the usb cable and insert the battery.Try to power on.
bliizzz said:
http://forum.xda-developers.com/showthread.php?t=1715272
Click to expand...
Click to collapse
hey, thank you both. Is NVFlash compatible with p990h?
HeadbangerHS said:
hey, thank you both. Is NVFlash compatible with p990h?
Click to expand...
Click to collapse
Have you done the KDZ procedure? I had to do it when I started playing with ROMs, and I have to say that you need a computer with Windows XP to do it, I tried with 7 in 2 machines and it did not work. Another thing: you have to remove the battery and plug in the usb while holding the volume down rocker.
Also, are you sure clockwork mod is not working? You cant release the power and volume down rocker until it boots into clockwork mod.
dark_sat said:
Have you done the KDZ procedure? I had to do it when I started playing with ROMs, and I have to say that you need a computer with Windows XP to do it, I tried with 7 in 2 machines and it did not work. Another thing: you have to remove the battery and plug in the usb while holding the volume down rocker.
Also, are you sure clockwork mod is not working? You cant release the power and volume down rocker until it boots into clockwork mod.
Click to expand...
Click to collapse
Yes, I tried the KDZ, but on a windows 7. I'll try it on my pc (where I use windows XP).
What happened on the windows 7 is that the phone DIDN'T GO INTO SW UPGRADE screen. And I removed the battery and everything.
Clockwork mod isn't working.
but thank you, I will try it here on my XP once I finish downloading everything again
HeadbangerHS said:
Yes, I tried the KDZ, but on a windows 7. I'll try it on my pc (where I use windows XP).
What happened on the windows 7 is that the phone DIDN'T GO INTO SW UPGRADE screen. And I removed the battery and everything.
Clockwork mod isn't working.
but thank you, I will try it here on my XP once I finish downloading everything again
Click to expand...
Click to collapse
I has to go into de SW Upgrade screen. Again, no battery, hold volume down (and do not let it go until the SW upgrade screen shows up), plug in usb.
This mode is OS independent, even if you plug the usb on a wall charger (I tested it and it worked), it HAS to get into this recovery mode.
That what you want to see (not my picture, took from Google Images):
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}

Really (I mean *really*!) bricked my phone. Nothing works.

Hi p970ies,
EDIT: NEW problems, see last pages.
here is my story:
I was on IZS v1.1, when I decided to go into recovery and make a full-wipe for having a "fresh install" again. You know, the phone was laggy, I had to many apps etc. I pressed the on/off-button for 1-2 secs to reboot into recovery, then my phone turned off and restarted but just with a "bright" black screen, the display was on. I thought "something went wrong", pulled the battery out and put it back in again, started, but then same screen again.
A few months ago an easy "unbricking" method (I know, not really unbricking) was to flash Redy2006's touch-recovery and boot into it with his scripts. So I flashed it (I know it's dumb, because of the u-boot and v30 thing, Idk), same result.
After that, I grabbed smartflash and two .bin/.fls packs of 2 roms, went into that special mode (phone off, press vol+, plug in) but there was no "sign" (screen that shows that you are in that mode) like the other day, the screen kept being black, but on.
Nonetheless the flashing worked and the software said everything alright. I started the phone but same result, in addition that there was now this effect: When the battery is put in and/or the phone is charging, the screen changes from being on and off. I can't do anything, no restarting with buttons, no LG screen, nothing but on and off, on and off. Every few seconds.
Thank you, I hope you experts can help me. (Even when I have the phone 2 years now and I was a ROM-junkie since the first day )
Edit: Tried smartflash with another patched v20 ROM. Tried KDZ Updater, just errors. But now the phone seems to boot, but there's nothing on the display, just the 4 softkeys are fading in and out.
Tomatengelee said:
Hi p970ies,
here is my story:
I was on IZS v1.1, when I decided to go into recovery and make a full-wipe for having a "fresh install" again. You know, the phone was laggy, I had to many apps etc. I pressed the on/off-button for 1-2 secs to reboot into recovery, then my phone turned off and restarted but just with a "bright" black screen, the display was on. I thought "something went wrong", pulled the battery out and put it back in again, started, but then same screen again.
A few months ago an easy "unbricking" method (I know, not really unbricking) was to flash Redy2006's touch-recovery and boot into it with his scripts. So I flashed it (I know it's dumb, because of the u-boot and v30 thing, Idk), same result.
After that, I grabbed smartflash and two .bin/.fls packs of 2 roms, went into that special mode (phone off, press vol+, plug in) but there was no "sign" (screen that shows that you are in that mode) like the other day, the screen kept being black, but on.
Nonetheless the flashing worked and the software said everything alright. I started the phone but same result, in addition that there was now this effect: When the battery is put in and/or the phone is charging, the screen changes from being on and off. I can't do anything, no restarting with buttons, no LG screen, nothing but on and off, on and off. Every few seconds.
Thank you, I hope you experts can help me. (Even when I have the phone 2 years now and I was a ROM-junkie since the first day )
Edit: Tried smartflash with another patched v20 ROM. Tried KDZ Updater, just errors. But now the phone seems to boot, but there's nothing on the display, just the 4 softkeys are fading in and out.
Click to expand...
Click to collapse
Oh man, its sad to hear that.
I can just think on two situations.
One is a broken screen, but thats pretty obvious.
And the other is a broken boot partition. Its very strange that you cant get into software upgrade mode. You sure you removed SIM, battery and SD, and then plugged it to the cable while holding the volume buttons?
I dont doubt you did it well, just making sure. Anyways AFAIK you should be able to enter that mode unless you got a broken boot partition.
Best of luck, sorry Im not of much help.
Grakel said:
Oh man, its sad to hear that.
I can just think on two situations.
One is a broken screen, but thats pretty obvious.
And the other is a broken boot partition. Its very strange that you cant get into software upgrade mode. You sure you removed SIM, battery and SD, and then plugged it to the cable while holding the volume buttons?
I dont doubt you did it well, just making sure. Anyways AFAIK you should be able to enter that mode unless you got a broken boot partition.
Best of luck, sorry Im not of much help.
Click to expand...
Click to collapse
Hi, thank you for your answer.
Yesterday oder so, I connected my phone without SIM, SD and battery while pressing vol+ to my pc and it showed the S/W-Update "Wait while update is in progress" or something. I was happy because the display isn't broken. But then I flashed again and the display is as black as before...
I thought about a broken bootloader. Do you guys know a way to fix it? Or the boot partition?
Tomatengelee said:
Hi, thank you for your answer.
Yesterday oder so, I connected my phone without SIM, SD and battery while pressing vol+ to my pc and it showed the S/W-Update "Wait while update is in progress" or something. I was happy because the display isn't broken. But then I flashed again and the display is as black as before...
I thought about a broken bootloader. Do you guys know a way to fix it? Or the boot partition?
Click to expand...
Click to collapse
Im pretty sure that if you can see the software update mode, you can unbrick the device.
When you said you reflashed something, do you actually mean that you smartflashed the fls and bin files from a stock v20 rom? AFAIK the bin file carries a bootloader with it so it should get fixed if your problem is the bootloader.
And by the way, while the phone has that black screen and is stuck booting... Are you able to use adb commands? You could try to jump to the recovery with "adb reboot recovery" to see if you got a working recovery.
Best of luck, tell me how it goes
Grakel said:
Im pretty sure that if you can see the software update mode, you can unbrick the device.
When you said you reflashed something, do you actually mean that you smartflashed the fls and bin files from a stock v20 rom? AFAIK the bin file carries a bootloader with it so it should get fixed if your problem is the bootloader.
And by the way, while the phone has that black screen and is stuck booting... Are you able to use adb commands? You could try to jump to the recovery with "adb reboot recovery" to see if you got a working recovery.
Best of luck, tell me how it goes
Click to expand...
Click to collapse
yep, I tried every version (10, 20, 30) in bin/fls and kdz. But I never got the screen to show something again.
And no, I can't use adb commands, sadly. It says "cannot find device" or something like that.
Tomatengelee said:
yep, I tried every version (10, 20, 30) in bin/fls and kdz. But I never got the screen to show something again.
And no, I can't use adb commands, sadly. It says "cannot find device" or something like that.
Click to expand...
Click to collapse
Huhmmm... Quite strange.
You can try to open up device manager, look for the phone (will probably have no drivers and the icon will have a yellow triangle) and force installing adb drivers. After that you are supposed to use adb even in middle of a boot.
I'd say that your best chance is to get to your recovery, so you can wipe everything (even formatting system) and start from scratch...
Anyways Im no expert at all... Just trying to help.
Grakel said:
Huhmmm... Quite strange.
You can try to open up device manager, look for the phone (will probably have no drivers and the icon will have a yellow triangle) and force installing adb drivers. After that you are supposed to use adb even in middle of a boot.
I'd say that your best chance is to get to your recovery, so you can wipe everything (even formatting system) and start from scratch...
Anyways Im no expert at all... Just trying to help.
Click to expand...
Click to collapse
Sometimes ADB works, but it says "device offline". When I flashed PRE-IZS fls/bin from the spanish forum, and then V30B bin/fls, something really weird happens: The phone is on, the wake-button works well - it turns on and turns off the display and the softkeys. But the screen doesn't show anything - just black.
Hello there!
Did You try out the B2C tool provided by LG? And there is one other tool provided by LG. Just try these oit. If they dont work, then try claiming it under warranty. They might replace the motherboard.
P.S: If You have the money, sell this piece of **** and get a Sony or Samsung. Cheers!
Sent from my LG-P970 using xda app-developers app
rokr05 said:
Hello there!
Did You try out the B2C tool provided by LG? And there is one other tool provided by LG. Just try these oit. If they dont work, then try claiming it under warranty. They might replace the motherboard.
P.S: If You have the money, sell this piece of **** and get a Sony or Samsung. Cheers!
Sent from my LG-P970 using xda app-developers app
Click to expand...
Click to collapse
I think I'm going to buy a Nexus 4, but I have to convince my parents
Oh and yes, phone is older than 2 years and in Germany we only have 2 years of warranty I think.
Tomatengelee said:
Sometimes ADB works, but it says "device offline". When I flashed PRE-IZS fls/bin from the spanish forum, and then V30B bin/fls, something really weird happens: The phone is on, the wake-button works well - it turns on and turns off the display and the softkeys. But the screen doesn't show anything - just black.
Click to expand...
Click to collapse
An easy, possible fix for The Device offline is to use the latest ADB. Just use the attached zip anywhere and use ADB, its the latest version from the android SDK, but just the files required for ADB. My nexus 4 had the same problem, but Solved it by updating ADB.
ykumar00 said:
An easy, possible fix for The Device offline is to use the latest ADB. Just use the attached zip anywhere and use ADB, its the latest version from the android SDK, but just the files required for ADB. My nexus 4 had the same problem, but Solved it by updating ADB.
Click to expand...
Click to collapse
damn it says "error: device not found" when in S/W or bootloop... or device offline in bootloop
any ideas?
did you try patched bins ? (for being able to boot into recovery right after the flash process, maybe you just need right wipes)
#700th post yay...
Ilko said:
did you try patched bins ? (for being able to boot into recovery right after the flash process, maybe you just need right wipes)
#700th post yay...
Click to expand...
Click to collapse
Yes, I did, but Smartflash works "less" than the KDZ-Updater. Actually the phone beeped today while it was on (with some kdz flashed) :silly:
Is it possible to convert patched bin/fls files to kdz?
I don't know, probably not... what I can say is that kdzu doesn't perform full wipes since it's intended to update the system and keep datas at the same time. You probably need wipes...
Ilko said:
I don't know, probably not... what I can say is that kdzu doesn't perform full wipes since it's intended to update the system and keep datas at the same time. You probably need wipes...
Click to expand...
Click to collapse
Oh ok... But with KDZ-Updater, it's possible to turn the phone off and on (screens is "on" but shows the color black while the softkeys are on too).
I'll try again with Smartflash... Do you know another version of it or a good tutorial? Maybe I've done the wrong method or something...
there are several tuts in this forum. smartflash is the quickest and safest way to restore / unbrick as it erases everything in the internal memory
Ilko said:
there are several tuts in this forum. smartflash is the quickest and safest way to restore / unbrick as it erases everything in the internal memory
Click to expand...
Click to collapse
I know, but it never works. That problem is so weird! :silly:
Man, nothing works... After smartflashing display flashing off and on again, after kdz display on, softkeys flashing
ADB side service is not active while in S/W mode. The only chance to access to recovery is to boot normally, and access to the device via ADB. The problems are : device needs to pass initial boot process for being able to be detected by ADB (even if you don't see the desktop it's ok), and USB debug must be enabled by default...
so, if you can't pass initial boot process, no chance to use ADB, and, if it passes, usb debug must be enabled or device will remain offline...
Ilko said:
ADB side service is not active while in S/W mode. The only chance to access to recovery is to boot normally, and access to the device via ADB. The problems are : device needs to pass initial boot process for being able to be detected by ADB (even if you don't see the desktop it's ok), and USB debug must be enabled by default...
so, if you can't pass initial boot process, no chance to use ADB, and, if it passes, usb debug must be enabled or device will remain offline...
Click to expand...
Click to collapse
Is there a chance to enable it manually?
the only chance is to flash a ROM which have it enabled by default for the most of them.
mine died because of the new twrp 2.6. It has definitively corrupted the boot partition as even smartflash can't ends its process. I had to buy another device...

[Q] Have I managed to HARD-BRICK my phone?

Switched from one provider to another, got a new phone which uses micro-sim, and couldnt get the p880 to read the new sim card, so I have been using the new phone, which is greatly inferior to the p880..
With the p880 just sitting around unused, i decided i might as well try to mod it, then get a regular sim card for it and start using it again. I think i killed it instead.
Before it died on me, I formatted / wiped / factory reset and then used the LG Mobile Support tool to upgrade to whatever the newest official release was.. 4.1.2??
At this point, here is what it can do:
1) When attempting to just turn it on and USE it as normal, it turns on, gets to the animated LG logo and stays there forever.
2) Power + Vol Down = OEM LG recovery menu
3) Power + Vol Up = Some kind of Restore graphic
4) Power + Vol Up and Down (AVX) = nothing
5) Plugged into USB with battery removed and holding Vol Down = home row LEDs light up, nothing else
Windows sees the phone as a "removable disk H:" when I plug it in, but the LG recovery software does not see it, and it also does not show up in the device manager..
At this point, all that I can seem to access is the "apply update from ADB" option to do an "adb sideload" command in recovery mode.. When I send over the root tool, the phone is happy. If I attempt to send anything else over via sideload, I always get kicked out of the process when it gets to the "verifying installation package" portion. I can wipe / factory reset to my heart's content, but I can get absolutely no further than this after attempting for about six hours yesterday.
Any hope for me or do i have a dope looking paperweight? Will providing you guys either the IMEI or S/N shed any light into a path to recovery?
Thanks for your time!
You have a booting rom, the device is not even close to hard brick. Is your bootloader unlocked? If yes you can flash a custom recovery with fastboot and install any rom you want.
Sent from my OmniROM-powered LG Optimus 4X HD
@one30six
Use this thread http://forum.xda-developers.com/showthread.php?t=2069723 or
Use this thread http://forum.xda-developers.com/showthread.php?t=2179126 to recover your phone.
Read the instructions with care and act as stated.
Good Luck.
sPEADy said:
@one30six
Use this thread http://forum.xda-developers.com/showthread.php?t=2069723 or
Use this thread http://forum.xda-developers.com/showthread.php?t=2179126 to recover your phone.
Read the instructions with care and act as stated.
Good Luck.
Click to expand...
Click to collapse
thank you, speady.. it turned out to be the first solution that you suggested, which i had seen before during my scouring of these forums.. but the real basis of my problem was that i had my phone plugged into the front-facing USB port of my computer rather than the one directly connected to the motherboard (on the back).. i guess the phone wasnt getting enough juice out of the front port to boot to S/W Update mode.. i am back to stock LG software and am eventually going to mod to another ROM
THANK YOU!

Categories

Resources