Root Samsung Galaxy Note N7000 on ICS DDLP8/ DXLP9 4.0.3 Firmware
Caution:
For 4.0.3 DDLP8/ DXLP9 only.
Follow all steps properly, do not proceed with rooting if u dont understand even one step.
Proceed at your own risk, i am not responsible for any problems.
Requirements:
Following are the pre-requisites before you start the process to root Samsung Galaxy Note N7000.
Although its not necessary to take back up the data before rooting the handset but its better to take precaution and back up all the required data.
Minimum charge should be at least 60% so that device may not get turned off during the rooting procedure.
Disable security tools installed on your computer so that it may not interrupt the rooting process.
Enable USB debugging on your Samsung Galaxy Note N7000. To do this, go to Settings > {} Developer Options > USB Debugging.
Download the rooting package for DDLP8 | DXLP9. The rooting package of DDLP8 and DXLP9 are different, so make sure to download the correct rooting package.
Download Odin required to carry out the rooting procedure.
File extracting software like WinRAR, WinZIP, 7-Zip or any other similar software.
Steps:
Follow the below mentioned process to root Samsung Galaxy Note N7000:
First of all download the respective rooting package as mentioned earlier for DDLP8 andDXLP9. Also download Odin. Extract the rooting package.
Open Odin on your computer.
Turn off your device to enter it in Download mode. Samsung Galaxy Note N7000 can be entered into Download mode by pressing Volume down Key, Center button (OK button) and while holding both of them simultaneously press the power button until the green robot is visible on the screen indicating that handset is in Download mode.
Connect the phone to the computer after which you get the COM port visible highlighted with yellow color as shown in the image.
After this, click on “PDA” present on right side and select the file named “CF-Root-SGN_DD_ODD_LP8-v5.5-CWM5.tar” for DDLP8 firmware or “CF-Root-SGN_DX_OLB_LP9-v5.5-CWM5.tar” for DXLP9 firmware from the extracted folder of rooting package.
Once the file is selected, click on Start to begin the rooting process. As soon as the rooting procedure is complete, your Galaxy Note N7000 device will be rebooted. Disconnect the phone once home screen is visible.
After rooting, enter your device into Recovery Mode. Recovery mode can be entered by pressing the Volume Up Key, center Button and while holding both of them simultaneously press the power button.
Once the phone is in recovery mode, select the options for Wipe data/factory reset and also select Wipe Cache partition. After this reboot the device by selecting reboot system now. All the options can be accessed by using volume rocker key and to select a particular option press the power button.
NOTE: At any point of time if the process of rooting gets stopped or affected due to any reason then there is no need to worry, just restart the process by re-inserting the battery.
BAM! Your Galaxy Note is Rooted on 4.0.3 DDLP8/ DXLP9 kernal
What are you trying to show or do?
Sent from my GT-N7000 using xda app-developers app
shivg86 said:
What are you trying to show or do?
Sent from my GT-N7000 using xda app-developers app
Click to expand...
Click to collapse
Stupidity
Really true...idont know why he is doing so
Sent from my GT-N7000 using xda app-developers app
dr.ketan said:
Stupidity
Click to expand...
Click to collapse
I think we should close this
Thread Closed
Related
I tryed this guide to root the phone [Galaxy s I9000]
androidgalaxys.net/guide-modding-galaxy-s/guida-root-sicuro-galaxy-s-gingerbread/
It seem working but it restart continusly.
What can be the problem?
Here's the screenshot of ODIN process.
Can't find screenshot!
Probably u took the kernel for the wrong firmware....
Inviato dal mio SGS con XDA
diegalax said:
I tryed this guide to root the phone [Galaxy s I9000]
androidgalaxys.net/guide-modding-galaxy-s/guida-root-sicuro-galaxy-s-gingerbread/
It seem working but it restart continusly.
What can be the problem?
Here's the screenshot of ODIN process.
Click to expand...
Click to collapse
Do the following and after that root your phone using cf root xxjw4 kernel from Odin. Check in cf root for galaxy gti9000 thread .
gcuchiha said:
Maybe its a bootloop maybe.Switch off your phone and check if download and recovery mode is available(see next paragraph)
If so follow the steps mentioned.
First of all download xxjw4 firmware for galaxy gt-I9000 from
http://www.hotfile.com/dl/150483619/708026d/I9000XXJW4_I9000OXAJW4_XEU.zip.html
1) Put your phone into Recovery mode (Vol up + Home + Power button) and perform a Wipe data/Factory reset, then a Wipe cache. When done pull the battery out for around ten seconds then re-insert.
(If recovery isn't working ignore this step)
2) Put the phone into Download mode (Vol down + Home + Power button)
3) Unzip the JW4 firmware folder you've downloaded to your Desktop.
4) Launch Odin and click on the button that says PDA and navigate to the PDA file you've just unzipped to your desktop and select it.
5) Connect your phone to your PC via USB. Odin will say Added and a box will turn yellow to indicate it has recognised your phone.
6) Click the start button in Odin and sit back and wait for Odin to flash your phone. When it's finished it will take a few minutes longer for the phone to reboot than is usual so please don't panic. The phone will reboot.
7) When the phone has rebooted, remove the USB cable and you now have the latest 2.3.6. It might be a good idea to repeat step 1 to make sure nothing of the old firmware is left behind.
And that's it, seven steps to 2.3.6 JW4 Value Pack and TouchWiz 4.
In case you want more info about flashing go to this site
http://www.theandroidsoul.com/galaxy-s-gets-official-value-pack-firmware-xxjw4-includes-touchwiz-4/
Enjoy
Click to expand...
Click to collapse
First of all I feel your pain. If your issue hasn't been solved by the above post I would recommend these two step by step guides to fixing your issue.
http://forum.xda-developers.com/showthread.php?t=1494493
I have personally used the above process without a problem, best of all it includes all the files you need to not only get back to stock but also to then get you back to ICS.
http://forum.xda-developers.com/showthread.php?t=1139050 This process I haven't used but a cursory search pulled it up. The first link is better and I can vouch for it but variety is the spice of life..
Hope this helps.
hi , i did the data/ffactory reset but now it just turns on, where the S appears and then it comes out the t mobile ad and just come out a black screen and the home key buttons remain on wat can i do to fixed it
my Galaxy s1 doesn't power up !
When i power it up he show the logo and then turn off
video:
youtube.com/watch?v=h5bX9LksF3k
Can you get it into download mode without it turning off? (Hold volume down + home button + power) Or recovery? (Hold volume up + home button + power?) Is it rooted with clockwork mode?
Sent from my GT-I9000 using xda premium
Maybe its a boot loop. Switch off your phone and check if download and recovery mode is available(see next paragraph).
If so follow the steps mentioned.
First of all download xxjw4 firmware for galaxy gt-I9000 from
http://www.hotfile.com/dl/150483619/708026d/I9000XXJW4_I9000OXAJW4_XEU.zip.html
1) Put your phone into Recovery mode (Vol up + Home + Power button) and perform a Wipe data/Factory reset, then a Wipe cache. When done pull the battery out for around ten seconds then re-insert.
(If recovery isn't working ignore this step)
2) Put the phone into Download mode (Vol down + Home + Power button)
3) Unzip the JW4 firmware folder you've downloaded to your Desktop.
4) Launch Odin and click on the button that says PDA and navigate to the PDA file you've just unzipped to your desktop and select it.
5) Connect your phone to your PC via USB. Odin will say Added and a box will turn yellow to indicate it has recognised your phone.
6) Click the start button in Odin and sit back and wait for Odin to flash your phone. When it's finished it will take a few minutes longer for the phone to reboot than is usual so please don't panic. The phone will reboot.
7) When the phone has rebooted, remove the USB cable and you now have the latest 2.3.6. It might be a good idea to repeat step 1 to make sure nothing of the old firmware is left behind.
And that's it, seven steps to 2.3.6 JW4 Value Pack and TouchWiz 4.
In case you want more info about flashing go to this site
http://www.theandroidsoul.com/galaxy-s-gets-official-value-pack-firmware-xxjw4-includes-touchwiz-4/
Enjoy
idon't have a recovery the phone isn't root and but i can get to the download mod !
still i tried what you said with the odin and it doesnt work
the phone wasn't root before and had a stock from the operator
If its a boot loop try this thread http://forum.xda-developers.com/showthread.php?t=984140
If not download the files from sammobile (2.3.6 xxjw4) put the .tar file in the PDA and 512 pit file in the pit section make sure the repartition is ticked then if it still in a boot loop search for the cfs root and flash that then get the file off the thread I gave you then flash that to the phone as instructed on the thread then your phone should work edit* you need to put your phone into download mode before plugging in and flashing
Sent from my GT-I9000 using xda premium
calum96 said:
If its a boot loop try this thread http://forum.xda-developers.com/showthread.php?t=984140
If not download the files from sammobile (2.3.6 xxjw4) put the .tar file in the PDA and 512 pit file in the pit section make sure the repartition is ticked then if it still in a boot loop search for the cfs root and flash that then get the file off the thread I gave you then flash that to the phone as instructed on the thread then your phone should work edit* you need to put your phone into download mode before plugging in and flashing
Sent from my GT-I9000 using xda premium
Click to expand...
Click to collapse
yeah i know the basics ! but stil it doesnt work ! can it be a hardware problem? and if it right how can i fix it ?
Did you try that method? And when did it start turning off, did you try mpding it or did it just start doing it? Does it he a knock when it turns off or is it at the same place everytime? If it stays turned on in download mode its probably software related also make sure the drivers are installed using kies
Sent from my GT-I9000 using xda premium
yizhak722 said:
idon't have a recovery the phone isn't root and but i can get to the download mod !
still i tried what you said with the odin and it doesnt work
the phone wasn't root before and had a stock from the operator
Click to expand...
Click to collapse
Does Odin recognize your phone (com12 or something like that in yellow)
If not then try different USB port or also different cable and computer.
According to my experience if you are able to go to download mode then there is always a way to fix the problem
Hi.. I am little new with Note with ICS
It has entered in a boot loop where it reaches the home screen. and in about 10 sec reboots itself. I tried taking out the battery, still same problem. Than I tried putting it in recovery mode and resetting it to factory settings by pressing power,up volume and home button together, but it want go to recovery mode, samsung logo and model no comes up than black screen and again samsung logo and model no. Tried it with pluged in to PC as well.
Any help will be appreciated
Thanx
Abdur
Hello abdurm, could you tell us your current firmware? You would require to give us details from Settings > About phone.
Also, did you try flashing anything? If so, what was it?
By pressing the Volume Down button + Home button + Power button simultaneously, does your device enter Download mode?
YLNdroid said:
Hello abdurm, could you tell us your current firmware? You would require to give us details from Settings > About phone.
Also, did you try flashing anything? If so, what was it?
By pressing the Volume Down button + Home button + Power button simultaneously, does your device enter Download mode?
Click to expand...
Click to collapse
It dosen give me enough time to check firmware version, it reboots. It is on ICS. It is stock and I have not tried fashing or anything.
Yes it goes in download mode by pressing Volume Down button + Home button + Power button simultaneously.
Flash gingerbread rom in PC ODIN only and it will automatically reboot by itself but if still stuck in samsung logo go to recovery mode and wipe data and cache.
abdurm said:
It dosen give me enough time to check firmware version, it reboots. It is on ICS. It is stock and I have not tried fashing or anything.
Yes it goes in download mode by pressing Volume Down button + Home button + Power button simultaneously.
Click to expand...
Click to collapse
Download pre rooted gb rom from my signature and flash it via pc odin. Your phone must be in download mode and don't change any settings in pc odin.
Cheers
sahilarora2003 said:
Download pre rooted gb rom from my signature and flash it via pc odin. Your phone must be in download mode and don't change any settings in pc odin.
Cheers
Click to expand...
Click to collapse
Thank you very much. Just one last thing I dont have to be rooted to instal this ROM and it is ok to flash directly from ICS . Just downloadFilename: SGN_XX_OXA_KJ1_FACTORYFS.zip and flash it. And it will leave me with GB?
abdurm said:
It dosen give me enough time to check firmware version, it reboots. It is on ICS. It is stock and I have not tried fashing or anything.
Yes it goes in download mode by pressing Volume Down button + Home button + Power button simultaneously.
Click to expand...
Click to collapse
Apologies abdurm, I foolishly presumed you would have made a note of your device's firmware details at some point in the past. It was stupid of me to ask you for the said information.
abdurm said:
Thank you very much. Just one last thing I dont have to be rooted to instal this ROM and it is ok to flash directly from ICS . Just downloadFilename: SGN_XX_OXA_KJ1_FACTORYFS.zip and flash it. And it will leave me with GB?
Click to expand...
Click to collapse
1] Download the pre-rooted stock Gingerbread firmware, SGN_XX_OXA_KJ1_FACTORYFS.zip and extract it to get the SGN_XX_OXA_KJ1_FACTORYFS.tar file.
2] After doing so, run PC ODIN, select the PDA tab in it and point to the extracted file (SGN_XX_OXA_KJ1_FACTORYFS.tar). Auto Reboot and F.Reset Time will be selected by default. Do not select anything else.
3] Put your device in Download Mode and then connect it to your PC via the USB cable. The ID:COM label in PC ODIN will turn yellow indicating your device is connected and recognised.
4] Click on the Start button in PC ODIN and wait for the label above ID:COM to say Pass. After it does so, disconnect your device from your PC.
Your device will reboot and you will be on a stock Gingerbread firmware with root privilege.
YLNdroid said:
Apologies abdurm, I foolishly presumed you would have made a note of your device's firmware details at some point in the past. It was stupid of me to ask you for the said information.
1] Download the pre-rooted stock Gingerbread firmware, SGN_XX_OXA_KJ1_FACTORYFS.zip and extract it to get the SGN_XX_OXA_KJ1_FACTORYFS.tar file.
2] After doing so, run PC ODIN, select the PDA tab in it and point to the extracted file (SGN_XX_OXA_KJ1_FACTORYFS.tar). Auto Reboot and F.Reset Time will be selected by default. Do not select anything else.
3] Put your device in Download Mode and then connect it to your PC via the USB cable. The ID:COM label in PC ODIN will turn yellow indicating your device is connected and recognised.
4] Click on the Start button in PC ODIN and wait for the label above ID:COM to say Pass. After it does so, disconnect your device from your PC.
Your device will reboot and you will be on a stock Gingerbread firmware with root privilege.
Click to expand...
Click to collapse
Thank you very much, my note is finally working. How can I go to ICS, it doesnt show up in software update
abdurm said:
Thank you very much, my note is finally working. How can I go to ICS, it doesnt show up in software update
Click to expand...
Click to collapse
Hello again abdurm, I am glad to learn your device is up and running again. :highfive:
Now that you are on a rooted firmware, I would advice you not to avail an OTA update as there is a very high likelihood of it breaking/undoing the root privilege.
Personally, I have not ventured into Ice Cream Sandwich yet and thus I have no right to guide you with the process of acquiring it. But, based on your quoted post may I ask you if you desire to have stock Ice Cream Sandwich with or without root privilege?
I recommend you thoroughly read dr.ketan's threads which explain the subject at hand.
hi
kindly i need a step by step to downgrade from 4.0.3 rooted to gingerbread 2.3.6
i i use pc odin like i upgrade do i brick the phone?
thank you
Using PC Odin is ok, gingerbread kernels do not have the brickbug.
khorss said:
Using PC Odin is ok, gingerbread kernels do not have the brickbug.
Click to expand...
Click to collapse
thank you for your reply so if i understood you what i do is :
download a stock gb room
then flash it using pc odin like i did when i upgrade it
then re root it
do i need to factory reset first or something before these steps? do i backup my settings to titanium first
thank you
drdish said:
thank you for your reply so if i understood you what i do is :
download a stock gb room
then flash it using pc odin like i did when i upgrade it
then re root it
do i need to factory reset first or something before these steps? do i backup my settings to titanium first
thank you
Click to expand...
Click to collapse
Why are you posting a question in the Development section? What you need to follow is Dr. Ketan's guide. If you are running ICS and downgrade to GB, you will have force closes the first time you boot. Then do the wipe, not in ICS
drdish said:
thank you for your reply so if i understood you what i do is :
download a stock gb room
then flash it using pc odin like i did when i upgrade it
then re root it
do i need to factory reset first or something before these steps? do i backup my settings to titanium first
thank you
Click to expand...
Click to collapse
First of all wrong section to ask question...should post such query in general section...
Yes make back up with Titanium Backup to save your apps...do not factory reset while on unsafe kernel (ICS kernel is unsafe kernel)..
Download any safe kernel and install and do factory wipe...then install Stock GB ROM..root it and enjoy...
silver2706 said:
First of all wrong section to ask question...should post such query in general section...
Yes make back up with Titanium Backup to save your apps...do not factory reset while on unsafe kernel (ICS kernel is unsafe kernel)..
Download any safe kernel and install and do factory wipe...then install Stock GB ROM..root it and enjoy...
Click to expand...
Click to collapse
thank you for your reply and sorry for posting here
one more question how to download safe kernel and do wipe (if there is any detailed post about it)
thank you again
drdish said:
thank you for your reply and sorry for posting here
one more question how to download safe kernel and do wipe (if there is any detailed post about it)
thank you again
Click to expand...
Click to collapse
Safe kernel for ics and gb = speedmod kernel.
1.Download pre rooted gb rom.
2. Use pc odin to flash the pre rooted rom.
3.The phone will keep fc while 1st boot. Dont panic. Switch off the phone completely and boot into recovery mode and wipe data+ cache.
4. After phone booted, install mobile odin and flash safe kernel.
5. Done, your gb rom now fully rooted.
Good luck.
Sent from my GT-N7000 using xda premium
Sir, please post in the correct sections, Q&A is for questions. Thank You.
lee yun khong said:
Safe kernel for ics and gb = speedmod kernel.
3.The phone will keep fc while 1st boot. Dont panic. Switch off the phone completely and boot into recovery mode and wipe data+ cache.
4. After phone booted, install mobile odin and flash safe kernel.
Click to expand...
Click to collapse
If flashed GB already using PC odin, its already safe.. there is no need to change kernel. GB kernels are safe. ICS, not so much
drdish said:
thank you for your reply and sorry for posting here
one more question how to download safe kernel and do wipe (if there is any detailed post about it)
thank you again
Click to expand...
Click to collapse
You can directly flash gb rom using pc odin
Dont do any wipes on ics..flash gb rom and then do the wipes
No other kernel is required to be flashed
sir,
http://forum.xda-developers.com/showthread.php?t=1424997
you'll find all the stock ROMs and the instructions in the link above.
STEP BY STEP instructions
[ the mobile and PC should be connected only when instructed in the process below ]
PC :
>> download the PC Odin3v1.87
>> download the ROM from the link above or from "samfirmware" [ http://samfirmware.com ]
(click on 'firmwares and files', scroll down the page, select 'smartphone' in the type list, 'android' in the OS list, 'GT-N7000 - Galaxy Note' in the model list, ' **** your country **** ' in the country list. Click on the 'send' button. All the firmwares released for your model will be listed, download the one you want to install. It will ask you to register to the site first, don't worry it is free)
>> you will download a file "N7000xxXXX_N7000xxxXXX_XXX.rar" (there will be numbers and alphabets instead of x and X). RAR is a compressed format, to unRAR the actual file/folder (which you need) you will need a program called 'WinRAR', look it up on google or download it from [ http://www.filehippo.com ]
>> you will get "N7000xxXXX_N7000xxxXXX_N7000xxXXX_HOME.tar.md5" and "SS_DL.dll" when you'll unRAR.
>> open the Odin program on your computer (if you are on windows vista or windows 7 right click on the "Odin3 v1.85.exe" and then click on "run as administrator" option, click on the "yes" option. the program will open). now click on the 'PDA' button (in the Odin program) and then point the location at/select the "N7000xxXXX_N7000xxxXXX_N7000xxXXX_HOME.tar.md5" file.
MOBILE :
>> press/hold down the volume 'down' button, don't release the volume 'down' button, press/hold down the 'home' button (in the front), and press and hold down the 'power' button until your device restarts, don't let go of the three buttons until you see the "Samsung Galaxy Note GT-N7000" screen. (release the three button when you see "Samsung Galaxy Note GT-N7000" on the screen)
>> press the volume 'up' button to continue.
>> connect the data cable to the PC[USB] and the mobile[MicroUSB]
PC :
>> you'll see a yellow box under ID:COM with "COMx" written in it. (x is a number)
>> now click the big "START" button (in the Odin program)
wait for the process to be over, and your mobile will reboot itself.
MOBILE :
>> press/hold down the volume 'up' button, don't release the volume 'up' button, press/hold down the 'home' button (in the front), and press and hold down the 'power' button until your device restarts, don't let go of the three buttons until you see the "Samsung Galaxy Note GT-N7000" screen. (release the three button when you see "Samsung Galaxy Note GT-N7000" on the screen)
>> press the volume 'down' button to get to "wipe data/factory reset" and press the 'power' button (it might be the 'home' button read the instruction on the mobile screen.. on top)
>> press the volume 'down' button to get to "wipe cache partition" and press the 'power' button (it might be the 'home' button read the instruction on the mobile screen.. on top)
>> "reboot system now" and press the 'power' button.
nokiamodeln91 said:
If flashed GB already using PC odin, its already safe.. there is no need to change kernel. GB kernels are safe. ICS, not so much
Click to expand...
Click to collapse
He mentioned he wanna keep his phone being rooted. Otherwise just as you said, it is not neccesary to flash any kernel. Thanks
Sent from my GT-N7000 using xda premium
Thank you all very much,
i will pass the stock gb rom via pc odin
after it reboot normally i will do a wipe
then root it
thank you all and again sorry for posting here didn't knew
100% done thank you again
Nice guide....
How to root your Samsung galaxy S3 Running Android 4.3 XXUGNA8
Steps:
1. Download Odin from this post.
2. Download I9305_CWM_Recovery.tar.md5
3. Unzip Odin to your desktop.
4. Copy the I9305_CWM_Recovery.tar.md5 to the same directory.
5. Boot your SGS in to download mode.
(Power off and then press and hold the power + volume down + home buttons at the same time)
6. Connect your phone to your PC using the cable that came with it.
7. If Kies is running on your pc shut it down.
8. Open the Odin application.
(Make sure your phone is detected, there will be a yellow square in the top left corner.)
9. Choose PDA button and select the I9305_CWM_Recovery.tar.md5.
10. Press start and wait. Your phone will be flashed and reboot when it is finished.
(After Odin finish let the device reboot to android at least one time before applying I9305_CWM_Recovery.tar.md5.)
11. When the phone reboot, power it off again.
12. Put the phone in recovery mode.
(Hold down power, volume up and home when the device is turned off and unplugged.)
13. After that you can flash the Root_SuperSU.1.02-Busybox.1.21.0.zip to be ROOTED to any firmware and make a backup and restore of your firmware, also you can now flash any custom rom / kernel made for GT-I9305.
Raistlin1158 said:
Steps:
1. Download Odin from this post.
2. Download I9305_CWM_Recovery.tar.md5
3. Unzip Odin to your desktop.
4. Copy the I9305_CWM_Recovery.tar.md5 to the same directory.
5. Boot your SGS in to download mode.
(Power off and then press and hold the power + volume down + home buttons at the same time)
6. Connect your phone to your PC using the cable that came with it.
7. If Kies is running on your pc shut it down.
8. Open the Odin application.
(Make sure your phone is detected, there will be a yellow square in the top left corner.)
9. Choose PDA button and select the I9305_CWM_Recovery.tar.md5.
10. Press start and wait. Your phone will be flashed and reboot when it is finished.
(After Odin finish let the device reboot to android at least one time before applying I9305_CWM_Recovery.tar.md5.)
11. When the phone reboot, power it off again.
12. Put the phone in recovery mode.
(Hold down power, volume up and home when the device is turned off and unplugged.)
13. After that you can flash the Root_SuperSU.1.02-Busybox.1.21.0.zip to be ROOTED to any firmware and make a backup and restore of your firmware, also you can now flash any custom rom / kernel made for GT-I9305.
Click to expand...
Click to collapse
my Galaxy S III i9300 not i9305
Then why are you posting in the wrong forum....
Raistlin1158 said:
Steps:
1. Download Odin from this post.
2. Download I9305_CWM_Recovery.tar.md5
3. Unzip Odin to your desktop.
4. Copy the I9305_CWM_Recovery.tar.md5 to the same directory.
5. Boot your SGS in to download mode.
(Power off and then press and hold the power + volume down + home buttons at the same time)
6. Connect your phone to your PC using the cable that came with it.
7. If Kies is running on your pc shut it down.
8. Open the Odin application.
(Make sure your phone is detected, there will be a yellow square in the top left corner.)
9. Choose PDA button and select the I9305_CWM_Recovery.tar.md5.
10. Press start and wait. Your phone will be flashed and reboot when it is finished.
(After Odin finish let the device reboot to android at least one time before applying I9305_CWM_Recovery.tar.md5.)
11. When the phone reboot, power it off again.
12. Put the phone in recovery mode.
(Hold down power, volume up and home when the device is turned off and unplugged.)
13. After that you can flash the Root_SuperSU.1.02-Busybox.1.21.0.zip to be ROOTED to any firmware and make a backup and restore of your firmware, also you can now flash any custom rom / kernel made for GT-I9305.
Click to expand...
Click to collapse
what about knox etc? is it safe to flash this? will knox will change from 0x0 to 0x1 after this?
godlesplay said:
what about knox etc? is it safe to flash this? will knox will change from 0x0 to 0x1 after this?
Click to expand...
Click to collapse
Yes this will trip knox, but you can use Triangle Away to reset the counter
If you are thinking of changing to custom ROMs then use CyanogenMod installer
G33k_ said:
Yes this will trip knox, but you can use Triangle Away to reset the counter
Click to expand...
Click to collapse
is there any other way to root s3 lte without rising knox?
Hi,
i got this Phone for my Girlfriend yesterday. There is 4.4.2 on the Phone. Does this work on this Version too?
Best regards
Chris
EDIT: sorry, wrong phone version.
Unterwegs @ G-Pad