Database Develop

[Q] i9000 can not boot

last week
i used i9000 to download software with wifi
because the battey was low , so it turned off~
then i took another battery ...
but my i9000 stuck on "I9000" screen again and again ~
i flash 2.2 rom,but the problem still go on
my i9000 don't have external SD Card
because it has 16GB internal SD Card
my question is : 1.i can use recovery mode , download mode is good
but after falsh 2.2 rom it display this notice
"E:can't mount /dev/block/mmcblk0p1 (or /dev/block/mmcblk0)
(invalid argument)
something went wrong while doing the lagfix. sorry"
2.i use 2.1 rom to falsh ,then it display this
"date wipe failed"
then i can use recovery mode
but when i use :update.zip , it notice
"(I/O error)
" E:can't mount /dev/block/mmcblk0p1 (or /dev/block/mmcblk0)"
could anyone help me pleeeeeeeeeease~~~~~
what'up with it?
The internal SD Card is bad? i need to change it ?

Help~~ ~
thanks a lot

So you can't turn it on even after flashing eclair?
Did you try ticking repartition?
Sent from my GT-I9000 using XDA App

snapper.fishes said:
So you can't turn it on even after flashing eclair?
Did you try ticking repartition?
Sent from my GT-I9000 using XDA App
Click to expand...
Click to collapse
yes .i tick re-repartition , and it can't start after flashing 2.1 rom or 2.2 rom
somebody said "when some date is writing during the voodoo runing,at that time power off by accident could make SD Card block"
"E:\" can't wipe , how can i fomat E: partition ?
i'm keeping on wait
thank you

lets get this correct download mode works
Flashed to Eclair but still fails to boot as voodoo was enabled /is enabled .
Therefore phone cannot be seen by PC and cannot boot to format .
can you get into clockwork recovery mode and format from that and wipe all data .
You said
i used i9000 to download software with wifi
because the battey was low , so it turned off~
What software was this you downloaded .
You get no other answers it will have to be a Samsung service centre .
jje

JJEgan said:
lets get this correct download mode works
Flashed to Eclair but still fails to boot as voodoo was enabled /is enabled .
Therefore phone cannot be seen by PC and cannot boot to format .
can you get into clockwork recovery mode and format from that and wipe all data .
You said
i used i9000 to download software with wifi
because the battey was low , so it turned off~
What software was this you downloaded .
You get no other answers it will have to be a Samsung service centre .
jje
Click to expand...
Click to collapse
thank you very much ~
i'm not good at English , so "Eclair" means 2.1 rom ?
1. when it turn off i can't get in recovery mode ,so voodoo is enabled when i flashed 2.2 rom .
2. i used a software named "UC xunlei" to down a salmpe 720P RMVB video at that time . then it turned off.
3. clockwork recovery can't use . only samsung recovery mode can get in.
4. my i9000 was sending to Samsung service centre yesterday, but they said "maybe they can't repair it either"
"sigh................."

I'll try to walk you through step by step through a method that has never failed..If it still fails then your internal SD might have issues..
1. Download XXJPU firmware from samfirmware.com
http://www.multiupload.com/PUSOOBQ8K5
The password to this zip file is: samfirmware.com
Once the file is extracted, you will have 4 files in it:
GT-I9000-CSC-MULTI-OXAJPU.tar.md5
I9000XXJPU-REV03-PDA-low-CL747761.tar.md5
MODEM_I9000XXJPU.tar.md5
s1_odin_20100512.pit
2. Open Odin
Download here: http://db.tt/QuA1G6s
That is a sure working Odin. The one I use. Extract that and run Odin3 v1.3.exe
3. In Odin:
check Re-Partition
Click PIT and select s1_odin_20100512.pit
Check and click PDA and select I9000XXJPU-REV03-PDA-low-CL747761.tar.md5
Check and click PHONE and select I9000XXJPU-REV03-PDA-low-CL747761.tar.md5 The file that has MODEM in its file name.. SORRY!!!!!
Check and click CSC and select GT-I9000-CSC-MULTI-OXAJPU.tar.md5
Do not touch any of the other options. Leave them the way they are.
3. Exit Kies (make sure it is not running AT ALL).
4. Put your phone into DOWNLOAD mode (volume down + power + home) and plug into your computer
5. Click START in Odin... if Odin gets stuck for a LONG time (progress bar isn't moving at all in both phone and Odin).. unplug phone, pull battery, restart computer and repeat from step 2.
6. Once Odin says it succeeded wait for phone to reboot.
7. If you still encounter the same error then report back here... I might have another idea. Hopefully you don't get the error again though...
Edit:
If that fails you can read this guy's post..
This guy seemed to have been lucky and got is supposed dead I9000m SGS working again. Here's his procedure:
http://forum.xda-developers.com/showthread.php?t=905975
Worth a shot.

anoneemooz~ thank you ~~
i'll try ~
i hope what you said can get my i9000 back~

anoneemooz said:
I'll try to walk you through step by step through a method that has never failed..If it still fails then your internal SD might have issues..
1. Download XXJPU firmware from samfirmware.com
http://www.multiupload.com/PUSOOBQ8K5
The password to this zip file is: samfirmware.com
Once the file is extracted, you will have 4 files in it:
GT-I9000-CSC-MULTI-OXAJPU.tar.md5
I9000XXJPU-REV03-PDA-low-CL747761.tar.md5
MODEM_I9000XXJPU.tar.md5
s1_odin_20100512.pit
2. Open Odin
Download here: http://db.tt/QuA1G6s
That is a sure working Odin. The one I use. Extract that and run Odin3 v1.3.exe
3. In Odin:
check Re-Partition
Click PIT and select s1_odin_20100512.pit
Check and click PDA and select I9000XXJPU-REV03-PDA-low-CL747761.tar.md5
Check and click PHONE and select I9000XXJPU-REV03-PDA-low-CL747761.tar.md5
Check and click CSC and select GT-I9000-CSC-MULTI-OXAJPU.tar.md5
Do not touch any of the other options. Leave them the way they are.
3. Exit Kies (make sure it is not running AT ALL).
4. Put your phone into DOWNLOAD mode (volume down + power + home) and plug into your computer
5. Click START in Odin... if Odin gets stuck for a LONG time (progress bar isn't moving at all in both phone and Odin).. unplug phone, pull battery, restart computer and repeat from step 2.
6. Once Odin says it succeeded wait for phone to reboot.
7. If you still encounter the same error then report back here... I might have another idea. Hopefully you don't get the error again though...
Edit:
If that fails you can read this guy's post..
This guy seemed to have been lucky and got is supposed dead I9000m SGS working again. Here's his procedure:
http://forum.xda-developers.com/showthread.php?t=905975
Worth a shot.
Click to expand...
Click to collapse
That solution looks fine but i'm in worst situation ever since i can't do this:
4. Put your phone into DOWNLOAD mode (volume down + power + home) and plug into your computer
My phone is stuck in the fisrt screen.( with this text Samsung Galaxy s i-I9000)
i can't enter in download mode, i also noticed that even the battery icon doesn't show up i only get loading icon not the battery one. Please help.

damnit, i tried the method anoneemooz posted. But Odin just stops after a couple of minutes flashing, and gave me the error message: Couldn't write to...
I can go in download modus and in recovery mode, but i cannot flash a ROM. I tried a couple of 2.2.1 ROMS

it dispaly " DATA_LOOP=FALSE CACHE_LOOP=FALSE DBDATA_LOOP=FALSE BIND_DATE_TO_DBDATA=FALSE"
now, i still can't wipe or fomat my internal SD Card
notice"E:can't mount /dev/block/mmcblk0p1 (or /dev/block/mmcblk0)
(invalid argument)"
also it shows "Error mounting /mnt/sdcard/ android_secure!
Skipping format..."

Check and click PHONE and select I9000XXJPU-REV03-PDA-low-CL747761.tar.md5
Should that not be MODEM_I9000XXJPU.tar.md5
Ignore it if i am wrong .
jje

JJEgan said:
Check and click PHONE and select I9000XXJPU-REV03-PDA-low-CL747761.tar.md5
Should that not be MODEM_I9000XXJPU.tar.md5
Ignore it if i am wrong .
jje
Click to expand...
Click to collapse
Oops yeah sorry..copy pasted the wrong thing for that part.
To OP: It seems as though you have a dead internal SD unfortunately..Well I could be wrong.

3 Button Fix for any firmware of SGS:
http://forum.xda-developers.com/showthread.php?t=785201
To all who run into Odin problem:
SORRY!!! For PHONE it should be the file that says MODEM in its filename. Copy pasted wrong name.

Download jg5 from samefirmware.com
Close everything relatet to keys and nps. Check in the tray and close if its running there. Use Odin3 v 3.1 and make sure u put the files in the right place:
PDA=Code
Phone=Modem
CSC=CSC
As pit download 512.pit
Check repartition.
AFTER tgis put ur phone in download mode and connect it.
Thrn click start and let it do its thing. If it doesnt work just try 3 or 4 times. Always been able to fix the error u get like this
Edit: or just check this out:
url]http://forum.xda-developers.com/showthread.php?t=845708[/url]
Sent from my GT-I9000 using Tapatalk

(i9001) Odin stuck at (AMSS.mbn download..)

HELLP!! i am trying to update my moms S Plus I9001 to a newer Nordic version (i9001xxkqg) using Odin (Multi Downloader v4.43) and it stops on AMSS.mbn!! How do i fix this! i am on my cabin now with only one PC. so do you have a any idea???
Here is what Odin says.
Download Start...
<0> Create File...
<1> StartThread Detected : 1
<2> StartThread Detected : 0
<3> StartThread Detected : 0
<4> StartThread Detected : 0
<5> StartThread Detected : 0
<6> StartThread Detected : 0
<7> StartThread Detected : 0
<8> StartThread Detected : 0
<1> setup connection...
<1> odin mode.. check plcatform verification.
<1> VerifyPlatform:V0, P0,R0
<1> START!!!
<1> set download environment.
<1> big partition size!!
<1> big partition size!!
<1> big partition size!!
<1> big partition size!!
<1> big partition size!!
<1> amss.mbn download..
(After 100 minutes)
I have tried many Odin versions but, only 4.43 works with (I9001 S Plus) And i have put the AriesVe.Ops in the Ops place and the Firmware in the One Package. And now my phone displays a yellow triangle and i cant turn it on!! plzzz help!! Plzzz!

I guess my phone is bricked.

Plzzz, help me.

Eirik2306 said:
Plzzz, help me.
Click to expand...
Click to collapse
1) remove battery and reinsert
2) go into download mode
3) ensure you got the correct Firmware and restart Odin
4) select location of files according to Firmware ( single file in PDA )
5) unchecked the " protect ops file" box on the Odin screen before starting
That should do it

Yeah.. Follow the above steps and you are good to go...
If my post helped, don't mind hitting THANKS ;-)

xsenman said:
1) remove battery and reinsert
2) go into download mode
3) ensure you got the correct Firmware and restart Odin
4) select location of files according to Firmware ( single file in PDA )
5) unchecked the " protect ops file" box on the Odin screen before starting
That should do it
Click to expand...
Click to collapse
That does not work for me, At the pda it says: wrong image type.
but it doensn't work at any way with protect ops on/off, and not with pda or one package.
can anyone help me?

jeantje said:
That does not work for me, At the pda it says: wrong image type.
but it doensn't work at any way with protect ops on/off, and not with pda or one package.
can anyone help me?
Click to expand...
Click to collapse
ok, lets try this again
First remove battery and reinsert
1) "Select OPS" AriesVE.ops
2) Unzip/unrar the ROM you are flashing.
If it's a single .tar.md5 file, check the option "One Package" in Odin and then load the .tar.md5 file using the One Package button at the very bottom. Odin will load it and check the MD5 checksum. and should be over in ten minutes
If your ROM consists of several .smd files,
Select Boot_loader.tar under BOOT
Select Modem under PHONE
Select PDA under PDA
Select CSC under CSC .
Press Start, Flashing should take about 10 minutes
If it fails, than try again with protect ops unchecked

:'(
xsenman said:
ok, lets try this again
First remove battery and reinsert
1) "Select OPS" AriesVE.ops
2) Unzip/unrar the ROM you are flashing.
If it's a single .tar.md5 file, check the option "One Package" in Odin and then load the .tar.md5 file using the One Package button at the very bottom. Odin will load it and check the MD5 checksum. and should be over in ten minutes
If your ROM consists of several .smd files,
Select Boot_loader.tar under BOOT
Select Modem under PHONE
Select PDA under PDA
Select CSC under CSC .
Press Start, Flashing should take about 10 minutes
If it fails, than try again with protect ops unchecked
Click to expand...
Click to collapse
hello, i'm dealing with the same situation :/
after unchecking the "protect ops" it goes as far as the "big partition size" error message and stalls again...
really really in need of help guys... :/

aspetos said:
hello, i'm dealing with the same situation :/
after unchecking the "protect ops" it goes as far as the "big partition size" error message and stalls again...
really really in need of help guys... :/
Click to expand...
Click to collapse
jeantje problem was solved by re downloading the Aries.ops from another source as samfirmwares was corrupted

xsenman said:
jeantje problem was solved by re downloading the Aries.ops from another source as samfirmwares was corrupted
Click to expand...
Click to collapse
xsenman do you have a direct link of Aries.ops that works? ty

aspetos said:
xsenman do you have a direct link of Aries.ops that works? ty
Click to expand...
Click to collapse
try this, have not checked it as, I use different phone
CWM For flashing with Odin: http://www.mediafire.com/?jg0jjdg8amjlj3b
AriesVe.ops http://www.mediafire.com/?ikx8iz8arzabx1h

xsenman said:
try this, have not checked it as, I use different phone
CWM For flashing with Odin: mediafire com/ ?jg0jjdg8amjlj3b
AriesVe.ops mediafire com/ ?ikx8iz8arzabx1h
Click to expand...
Click to collapse
Is it normal that it now seems to be on "recovery.img download" for like 9 minutes?
I used the above CWM For flashing with Odin, AriesVE.ops and provided Odin version (verified same odin version was used as previous attempts).
The "Protect OPS" check box is checked, right?

aspetos said:
Is it normal that it now seems to be on "recovery.img download" for like 9 minutes?
I used the above CWM For flashing with Odin, AriesVE.ops and provided Odin version (verified same odin version was used as previous attempts).
The "Protect OPS" check box is checked, right?
Click to expand...
Click to collapse
minimum time is not less than 10 min, so give it time, yes protect ops should be checked, inly If failed than try unchecked

I solved this problem with BroodROM RC5 all-in-one tar file, here is what I did:
A) Remove the .md5 extension and make it .tar
B) Use other USB port
C) Remove KIES and downloaded standalone drivers pack
D) Sit back and waited for 30 minutes until flashing complete

xsenman said:
minimum time is not less than 10 min, so give it time, yes protect ops should be checked, inly If failed than try unchecked
Click to expand...
Click to collapse
23 minutes and counting...
just to check, nothing moves on the phone screen (like a bar indicator)
Is that normal?

aspetos said:
23 minutes and counting...
just to check, nothing moves on the phone screen (like a bar indicator)
Is that normal?
Click to expand...
Click to collapse
hmm, think its stuck, do a battery pull to get out of it and you can try darristan suggestion

xsenman said:
hmm, think its stuck, do a battery pull to get out of it and you can try darristan suggestion
Click to expand...
Click to collapse
tried with the "Protect OPS" unchecked (just in case), left it a fair 10+ minutes, no indication, etc...
I'll try darristan suggestion. But excuse me for asking to be a bit more elaborate as far as steps are concerned, it's like 7:30 AM here and had a long night...
Is there a post relative to darristan downloads and/or procedures?
ty

aspetos said:
tried with the "Protect OPS" unchecked (just in case), left it a fair 10+ minutes, no indication, etc...
I'll try darristan suggestion. But excuse me for asking to be a bit more elaborate as far as steps are concerned, it's like 7:30 AM here and had a long night...
Is there a post relative to darristan downloads and/or procedures?
ty
Click to expand...
Click to collapse
here http://forum.xda-developers.com/showthread.php?p=20392786

darristan said:
I solved this problem with BroodROM RC5 all-in-one tar file, here is what I did:
A) Remove the .md5 extension and make it .tar
B) Use other USB port
C) Remove KIES and downloaded standalone drivers pack
D) Sit back and waited for 30 minutes until flashing complete
Click to expand...
Click to collapse
unfortunately no luck either...
stuck on amss.mbn download again, with out any indicators on the phone screen...
am i properly foobared?

aspetos said:
unfortunately no luck either...
stuck on amss.mbn download again, with out any indicators on the phone screen...
am i properly foobared?
Click to expand...
Click to collapse
Suggest you read the i9001 WIKI http://forum.xda-developers.com/wiki/Samsung_Galaxy_S_Plus/GT-I9001#Flashing to check, if there is anything you may or may not be doing.

[Q] Problem with recovery

Hello all at first,
Iam n00b at the modding scene so correct me if iam wrong
I tried to install a Custom firmware, i did a backup of my device first.
But i have a problem with the recovery of my samsung GT-9001 device, i installed CWM 5.5.0.4 and i did a backup, somehow my internal SD is back-upd, en deleted firmware files??? and now iam stuck in CWM. Iam trying to recover my backup but it dont seems to be valid or something? really weird becease after the installation of CWM, the first thing i did was making a backup.
Its saying something like:
Checking md5 sums...
Erasing boot before restore...
Restoring boot image...
Restoring system...
Restoring data...
.android_secure.img not found. Skipping restore of /sdcard/.android_secure.
Restoring cache...
Restore Complete.
After this proces my phone is stuck in CWM screen please help me iam very noob and just started to work with custom firmware,
Sorry for my bad english!
Edit:
Searched 4 Hours for a sollution plz help!

Re-FleX_NL said:
Hello all at first,
Iam n00b at the modding scene so correct me if iam wrong
I tried to install a Custom firmware, i did a backup of my device first.
But i have a problem with the recovery of my samsung GT-9001 device, i installed CWM 5.5.0.4 and i did a backup, somehow my internal SD is back-upd, en deleted firmware files??? and now iam stuck in CWM. Iam trying to recover my backup but it dont seems to be valid or something? really weird becease after the installation of CWM, the first thing i did was making a backup.
Its saying something like:
Checking md5 sums...
Erasing boot before restore...
Restoring boot image...
Restoring system...
Restoring data...
.android_secure.img not found. Skipping restore of /sdcard/.android_secure.
Restoring cache...
Restore Complete.
After this proces my phone is stuck in CWM screen please help me iam very noob and just started to work with custom firmware,
Sorry for my bad english!
Edit:
Searched 4 Hours for a sollution plz help!
Click to expand...
Click to collapse
Try mounting your internal SD to your computer through recovery. Tell me what it does and if there is anything on the disk (assuming it mounts)

AlwaysDroid said:
Try mounting your internal SD to your computer through recovery. Tell me what it does and if there is anything on the disk (assuming it mounts)
Click to expand...
Click to collapse
Yes it mounts and there are a few directory's.
-Android
-clockworkmod (with backup files)
-Cache
And some files

This will help for uuuuu
1. U just goto download mode and flash stock ROM GB 2.3.6......reboot
2. U just goto recovery mode wipe all data and wipe cache
3. U just goto download mode flash cwm and reboot
4. U just goto recovery mode restore your backup and reboot
5. If u have any problem after this u just goto recovery mode wipe cache,dalvik cache,fix permission and reboot
6. U just goto ROM manager application and fix permission
7. Reboot and try now
I think maybe it will work for uuuuuu.........Have a success fun:laugh::good:

Aj rocker said:
1. U just goto download mode and flash stock ROM GB 2.3.6......reboot
2. U just goto recovery mode wipe all data and wipe cache
3. U just goto download mode flash cwm and reboot
4. U just goto recovery mode restore your backup and reboot
5. If u have any problem after this u just goto recovery mode wipe cache,dalvik cache,fix permission and reboot
6. U just goto ROM manager application and fix permission
7. Reboot and try now
I think maybe it will work for uuuuuu.........Have a success fun:laugh::good:
Click to expand...
Click to collapse
Ok, thx for your reply i will try it out takes alot of time becuese i have to folow all tutorials i think

Aj rocker said:
1. U just goto download mode and flash stock ROM GB 2.3.6......reboot
Click to expand...
Click to collapse
First step iam having a little trouble with that! also done a lot of searching and i cant find the sollution :S
Trying to flash stock rom to my device trough ODIN, but it keeps hanging on setup connection.
Code:
Download Start...
<0> Create File...
<1> StartThread Detected : 0
<2> StartThread Detected : 1
<3> StartThread Detected : 0
<4> StartThread Detected : 0
<5> StartThread Detected : 0
<6> StartThread Detected : 0
<7> StartThread Detected : 0
<8> StartThread Detected : 0
<2> setup connection...
-I installed KIES (Drivers)
-Shutdown running proceses
-Try to do it again diffrent USB port
-Take out battery and swith to download mode again
Still no response...
Iam using CWM 5.5.0.4

steps and tips to flash
Boss u do this things correctly step by step...........
1. U just uninstall whatever u installed for ur samsung mobile drivers like( kies,driver,etc...)
2. U download this file (http://drivers.softpedia.com/get/MOBILES/Samsung/SAMSUNG-USB-Driver-for-Mobile-Phones-15150.shtml) and install on ur computer
3. U connect ur mobile to computer by using USB cable
4. Power off ur mobile and goto download mode(power off + volume down + menu key)
5. Ur mobile turns into download mode( yellow board with Android icon)
6. Open Odin 1.85 in your computer........when open the Odin 1.85 yellow icon enable on rightside top with this text(com14,com16,com17.....). If u not see the yellow icon in Odin 1.85 u just press the power button one time and then enter to the download mode
7. When u see the yellow icon OK ready to select the jw4 ROM files(PDA,PHONE,CSC,PIT(512 OR 513)......don't turn off application or phone........If u get any error on Odin 1.85...... u want to enter the download mode another time without disconnect the USB cable........when the installing complete ur mobile will be automatically reboot
8. When ur mobile reboot it automatically complete final installation process...... if u get red errors on stock recovery mode u just clear only wipe cache and dont clear wipe all data..........reboot system now:good:
Correctly u do this process step by step means it will workkkkkkkkkkk:victory:

Ok, iam the n00b here but i think you have it wrong... i dont own a i9000 model but a 9001 model so i have galaxy s Plus!
And a request from me 2 you if you say what i can do like download stock Firmware can u post a link to the correct one?? I dont want to make more mistakes! But thx anyway for you replys... iam trying with odin 1.85 but it is way diffrent then version 4.... i dont have a clue what to do and where to begin if it comes up to odin 1.85. With version 4 i followed the tutorial and got stuck as u c in earlier posts.

Ok... i figured out what i was doing wrong and i almost cant say it...
I was holding the wrong key combination!!!! (POWER BUTTON + VOLUME UP + HOME) And i had to push VOLUME DOWN!! INSTEAD OF UP!
my phone was in RAMDUMP MODE not in download mode....
Sorry for my n00b action! but really much thx! to all who replyed!

Hi, ReFlex_NL, if you stuck in Bootloop after flashing CWM, your Problem will be solved here. :good:
Downloadmode : Vol. down + Home + Power
For flashing I9001 use Odin 4.43 only

lecter100 said:
Hi, ReFlex_NL, if you stuck in Bootloop after flashing CWM, your Problem will be solved here. :good:
Downloadmode : Vol. down + Home + Power
For flashing I9001 use Odin 4.43 only
Click to expand...
Click to collapse
Thx for your response but the problem is solved! look to my previous post i was holding the wrong button!!!!!!!! :crying::silly:

Put out the Battery for a few Minutes and then try again to go in Downloadmode. If it doesn't help, than you can try the Method in Broodplanks Tutorial (Chapter three). credits to Broodplank.

Ya fine I understand ur problem bossssss......
1. U r in stock ROM means first u want to take backup of current
2. Then u want to clear the current ROM (wipe all data and wipe cache)
3. Now the time to flash the zip file
4. Reboot system now
5. When the reboot is finish till now u not see the full features the new ROM means........
6. Goto the recovery mode and now u want clear only (wipe cache and wipe dalvik cache)
7. Reboot and enjoy......
When u like it press thanks........Aj rocker:good::fingers-crossed:

Aj rocker said:
Ya fine I understand ur problem bossssss......
1. U r in stock ROM means first u want to take backup of current
2. Then u want to clear the current ROM (wipe all data and wipe cache)
3. Now the time to flash the zip file
4. Reboot system now
5. When the reboot is finish till now u not see the full features the new ROM means........
6. Goto the recovery mode and now u want clear only (wipe cache and wipe dalvik cache)
7. Reboot and enjoy......
When u like it press thanks........Aj rocker:good::fingers-crossed:
Click to expand...
Click to collapse
http://forum.xda-developers.com/showpost.php?p=24831012&postcount=1330
this was sollution.... somehow BOOT was destoyed

Back to Stock Recovery

Hello everybody
I have tried to find something about getting the phone back to stock but with no success
Here is my problem :
I have changed the stock recovery and added 2 mods , old tv shutdown , and a battery mod . about 1 year ago
I think my phone has some hardware problems because it keeps shutting down for no apparent reason and it does this a few times a day and i want to take it back to Vodafone to be checked on warranty .
I want to retun it to the stock out of the box but i have problems finding how to restore the stock recovery , is there a way ?
Can i delete the 2 mods without flashing the whole ROM ?
Sorry if this topic is redundant with another but i didn't find it .
I have a samsung galaxy s plus i9001 Vodafone Romania
Other info :
2.3.5
base band : i9001BUKP1
version number GINGERBREAD.BUKP2

R: Back to Stock Recovery
You can find the stock recovery in the i9001 wiki page, bit i think that flashing it would be useless for your problem. You should do a nandroid backup before installing any mod...
Inviato dal mio frigo a pedali.

i have found the following information
Stock recovery
If for some reason you ever need to go back to stock recovery, wintel_mac has prepared a zip you can install in CWM or FeaMod:
9001_stock_recovery-signed.zip
Click to expand...
Click to collapse
But not sure how to use the file ...
I have made a back-up with Titanium before adding the 2 Modes .

fast way to get it back: Download you exact same firmware from sammobile.com and flash it with odin! you are back to very very stock! take it to vodafone and you are done!!
if you have putted some tweak on it this ethod will also remove it so you are totally sure about the warranty to be back! If you are rooted before perform this action download and flash from recovery the un-root zip from the guide!
for information about odin and this other stuff please refer to the guide! there is everything explained! If you have anymore dubts visit q&q i9001 thread inthe q&a section of the i9000 forum!

ok, so i changed the recovery now i have the stock one , i have made a recovery with Titanim and the old tv shud down has gone , but the batery MOD is still active , any ideea on how tk delete it ?

laurcapa said:
ok, so i changed the recovery now i have the stock one , i have made a recovery with Titanim and the old tv shud down has gone , but the batery MOD is still active , any ideea on how tk delete it ?
Click to expand...
Click to collapse
Download a same firmware and flash with Odin brother...the person one post before you already told you what to do ==

and now for some updates
I wanted to install cm9 and as required i had to install clockworkmod recovery , I've installl version v6.0.1.3 but i have a problem with it , it seems that the home button is not working properly , when i press it it just moves the cursor up, the button on the left moves it down ... read that is a touch recovery , but the touch is not working on it
I managed to soft-brick the phone because by mistake instade of a md5 rom i selected a zip by mistake, the phone showed the BSOD and the only mode it will entered was ROMDUMP ore something like that , but managed to get around by flashing boot_loader fond on the the forum, now the phone enters in download and recovery but i have a problem , because the recovery does not work i'm trying to flash anoter recovery using odin , but i does not start , i get the following log :
Download Start...
<0> Create File...
<1> StartThread Detected : 0
<2> StartThread Detected : 1
<3> StartThread Detected : 0
<4> StartThread Detected : 0
<5> StartThread Detected : 0
<6> StartThread Detected : 0
<7> StartThread Detected : 0
<8> StartThread Detected : 0
<2> setup connection...
<2> e - dll cannot setup connection with the target.
<0> Destroy instant..
<0> Killed timer
or there is another message
<7> StartThread Detected : 0
<8> StartThread Detected : 0
<1> setup connection...
<1> odin mode.. check plcatform verification.
<1> VerifyPlatform:V0, P0,R0
I am stuck , some advice on how to flash the current recovery ?

laurcapa said:
and now for some updates
I wanted to install cm9 and as required i had to install clockworkmod recovery , I've installl version v6.0.1.3 but i have a problem with it , it seems that the home button is not working properly , when i press it it just moves the cursor up, the button on the left moves it down ... read that is a touch recovery , but the touch is not working on it
I managed to soft-brick the phone because by mistake instade of a md5 rom i selected a zip by mistake, the phone showed the BSOD and the only mode it will entered was ROMDUMP ore something like that , but managed to get around by flashing boot_loader fond on the the forum, now the phone enters in download and recovery but i have a problem , because the recovery does not work i'm trying to flash anoter recovery using odin , but i does not start , i get the following log :
Download Start...
<0> Create File...
<1> StartThread Detected : 0
<2> StartThread Detected : 1
<3> StartThread Detected : 0
<4> StartThread Detected : 0
<5> StartThread Detected : 0
<6> StartThread Detected : 0
<7> StartThread Detected : 0
<8> StartThread Detected : 0
<2> setup connection...
<2> e - dll cannot setup connection with the target.
<0> Destroy instant..
<0> Killed timer
or there is another message
<7> StartThread Detected : 0
<8> StartThread Detected : 0
<1> setup connection...
<1> odin mode.. check plcatform verification.
<1> VerifyPlatform:V0, P0,R0
I am stuck , some advice on how to flash the current recovery ?
Click to expand...
Click to collapse
Maybe you're using a CWM with the menu button ?
And it's not true that you only can get in RAMDUMP mode. when your device is off. hold volume down + power until you see download mode, if that doesn't work try this:
quoted from my unbrick tutorial:
CHAPTER 3. Getting in Download Mode
If your Samsung Galaxy S Plus is (partially) bricked and you have BSOD:
1. Unplug your phone if its connected to your PC
2. Hold Vol UP + Vol Down + Power, the screen will flash black
3. Continue holding down all 3 buttons, you will see the BSOD screen again, continue holding all 3 buttons, the screen will flash black again
4. Release the power button only. This will put you into Download Mode
Don’t expect it to work the first time you try it. If it keeps failing try the alternative:
1. Start Odin Multi Downloader
2. Connect your phone (which is in BSOD) to the PC
3. Wait till Windows finished installing drivers and Odin recognized your phone
4. Hold Vol Down + Home + Power, once the black screen flashes, release the Power button. This will put you into Download Mode
If this also doesn’t work and you are getting nervous about your situation:
1. Go to DealXtreme, this small product of $1.60 can help getting in download mode instantly
2. Buy it and wait for it’s arrival (the shipping is free but it can take a few days, so you will have no phone at that time)
3. Now when your phone is off, plugin the jig and wait until it goes on, now it will go in download mode and you’re ready to go
oh and the odin bug is very common, just restart odin and try again

laurcapa said:
and now for some updates
I wanted to install cm9 and as required i had to install clockworkmod recovery , I've installl version v6.0.1.3 but i have a problem with it , it seems that the home button is not working properly , when i press it it just moves the cursor up, the button on the left moves it down ... read that is a touch recovery , but the touch is not working on it
I managed to soft-brick the phone because by mistake instade of a md5 rom i selected a zip by mistake, the phone showed the BSOD and the only mode it will entered was ROMDUMP ore something like that , but managed to get around by flashing boot_loader fond on the the forum, now the phone enters in download and recovery but i have a problem , because the recovery does not work i'm trying to flash anoter recovery using odin , but i does not start , i get the following log :
Download Start...
<0> Create File...
<1> StartThread Detected : 0
<2> StartThread Detected : 1
<3> StartThread Detected : 0
<4> StartThread Detected : 0
<5> StartThread Detected : 0
<6> StartThread Detected : 0
<7> StartThread Detected : 0
<8> StartThread Detected : 0
<2> setup connection...
<2> e - dll cannot setup connection with the target.
<0> Destroy instant..
<0> Killed timer
or there is another message
<7> StartThread Detected : 0
<8> StartThread Detected : 0
<1> setup connection...
<1> odin mode.. check plcatform verification.
<1> VerifyPlatform:V0, P0,R0
I am stuck , some advice on how to flash the current recovery ?
Click to expand...
Click to collapse
First this is not where to ask, just so that you know!
Second, i really sugget to go back to stock compleatly and then proceed again to get CM9.
So always via odin flash you original firmware from sammobile.
For the messages that odin gives, try all the port on your computer, due to the fact that not all port works with it! when i use odin on my virtual machin with windows xp sometimes one of my usb works sometime the other. but the pc is always the same, so try them ALL!
If instead you want to try and flash just a custom recovery use broodplank quickflasher! it is easy and safe!
hope it works out!

maybe you misunderstood me , i will try be a little more explicit , so :
my phone is not bricked at this moment , I only tried to explain all the steps that got me to the current situation
i am able now to go in recovery mode (but this recovery does not allow me to do anything because the home button doesn't enable anything , only scrolls throw the menu , i explained in the previous post) and in download mode ...
the problem is that after i flashed the boot_loader after being stuck in RAMDUMP that solved the BSOD when i try to flash another recovery with odin it does not work and i don't think is a port problem because odin recognizes the phone , it gets stuck at <1> VerifyPlatform:V0, P0,R0 and does nothing .
in summary :
-flash sotck recovery with clockworkmod recovery v6.0.1.3 (not with odin)
-flash with odin a zip file by mistake got the phone semi-brick , BSOD only RAMDUMP worked
-flashd with odin from BSOD the bootloader and got the phone back
-not able to flash anoter recovery with odin because the above problem
solutions ?

laurcapa said:
it gets stuck at <1> VerifyPlatform:V0, P0,R0 and does nothing .
-not able to flash anoter recovery with odin because the above problem
solutions ?
Click to expand...
Click to collapse
Have you press the reset button in Odin after you flash the Bootloader?
Sometimes...(Not sometimes but every time for me) the Odin get stucked if you try to flash for second time without reset it...

After i flashed the BootLoader odin reseted the phone and told me to remove the serial link , so didn't requested me to reset anything

laurcapa said:
After i flashed the BootLoader odin reseted the phone and told me to remove the serial link , so didn't requested me to reset anything
Click to expand...
Click to collapse
Odin won't ask you to reset anything but there is a reset button on the right hand side...

nope , haven't reseted anything , but tried several times after closing and restarting odin

laurcapa said:
nope , haven't reseted anything , but tried several times after closing and restarting odin
Click to expand...
Click to collapse
Close Odin, Restart Odin again...press the reset files button, select ariesve.ops, one package, CWM.tar.md5
try and see...

laurcapa said:
nope , haven't reseted anything , but tried several times after closing and restarting odin
Click to expand...
Click to collapse
try from another pc. or battery pull let it be half an hour insert battery and try again. as things are now you can just try again and again to flash something.
or try out heimdall, i don't know if i9001 is supported but maybe it can work!

I solved the problem , after this post we cand consider the end of this topic.
The problem was due to the fact that i was using Android Reboot to get in recovery or Download mode , even if the phone showed me like i was in download mode i had the above error <1> VerifyPlatform:V0, P0,R0 even if the com port was open in odin ... after booting in download mode by pressing the buttons odin was able to flash the recovery .
What i learnd from this experience :
clockworkmod recovery v6.0.1.3 is not stable and for my device it didn't worked , not to be use
do not use .bat reboots to get in download mode when using odin
otherwise i now run CM10 with phantom kernel , i hope the phone doesn't restarts like before
thanks to everyone for the help and support
best regards

AW: Back to Stock Recovery
you have cm10 with other kernel and stock recovery? why? you must have for updates cwm or twrp recovery. a stable cwm is version 5.5.4.
Gesendet von meinem GT-I9001 mit Tapatalk 2

i have the following :
cwm version 5.5.4
CM v10
Phenom kernel

Hy
New question .
Can i use a custom kernel on a stock ROM ? Right now my phone is stock , i'm wondering if i install clickmod recovery and flush the custom kernel will it work .
10x

Too long instaling CWM with Odin?

Hi!
I try to Instal ClockworkMod on my Samsung Galaxy S Plus to install CyanogenMod 10.1. I use this tutorial for that:
Pre-requisites:
Make sure that you have charged your mobile at least up to 70% so that installation process will occur without any interruption.
It is recommended that you should take a backup of all your important personal data such as SMS, MMS, APN, contacts etc. to the external microSD card.
You must install your mobile’s drivers on PC. If you have installed Kies on your computer then you don’t need to install it separately.
Procedure to install Clockworkmod recovery on Samsung Galaxy S Plus I9001:
First download Odin v4.43 software and install it on your PC. It is necessary for flashing recovery on mobile.
Click here to download.
Download Clockworkmod recovery for Samsung Galaxy S Plus.
Also download AriesVE OPS file.
Now you have to boot your mobile into downloading mode. For that, first switch off your mobile then press & hold volume down + power button + home button simultaneously until it shows downloading message on your screen.
Now connect mobile to PC via USB cable.
Launch Odin software which you have installed previously on your PC. You will see Added!! message in Odin’s message box. If you won’t get this message make sure that you have installed mobile drivers properly.
Now click on the OPS button and then select AriesVE OPS file.
Click One Package button on Odin and select cwm6032-ariesve-touch-odin.tar file which you have downloaded earlier.
Ensure that Auto-Reboot and F.Resest Time is checked. Make sure that you haven’t clicked anywhere else.
Hit start button to flash recovery on mobile. After successful installation of recovery your mobile rebooted automatically. At the same time you will get pass message in Odin’s message box.
However if you mobile get stuck or you get a fail message then exit the Odin, disconnect mobile from computer, remove battery and re-insert it and follow the above procedure again.
Well done! Clockworkmod Recovery is now installed on your Samsung Galaxy S Plus I9001. Do let us know how it is working. If you any query regarding this article, you can ask us freely. We will try our level best to solve it.
Note: For entering into Clockworkmod recovery press & hold volume up + power button + home button simultaneously.
Click to expand...
Click to collapse
After 30 minutes of waiting I unppluged mobile and turn it off. After rebooting I saw icon of mobile and computer with yellow triangle with exclamation mark. After working with this once more I go to download mode and now is more than next 30 minutes...
[
Odin massages:/FONT]
Download Start...
<0> Create File...
<1> StartThread Detected : 1
<2> StartThread Detected : 0
<3> StartThread Detected : 0
<4> StartThread Detected : 0
<5> StartThread Detected : 0
<6> StartThread Detected : 0
<7> StartThread Detected : 0
<8> StartThread Detected : 0
<1> setup connection...
<1> odin mode.. check plcatform verification.
<1> VerifyPlatform:V0, P0,R0
<1> START!!!
<1> set download environment.
<1> recovery.img download..
Click to expand...
Click to collapse

I waited for 50 minutes and turn off installation. Tryied 3 more times, only detecting wrong port if I try to change USB. What to do with this now?

Try the same with this. It'll be ok
NB: This is for i9001 only. Please don't try this in other devices.

It worked instantlly! Thank you very much!:good: Now I go to install CyanogenMod.

first sorry for my bad english
i tried 6.0.1.1 but after 20 min half get green but do nothing....what should i do? may i still waiting?
...i tried CWM 6.0.2.8 and its ok now
thx