Hi,
I was downgrading from JB to GB, while doing odin, it was failed and I removed the battery and tried doing it again, but no use. nothing is happening. Please help. very very urgent.
Your help is higly appreciated.
The odin is freezing at this place.
<ID:0/021> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> APBOOT_I9000XWJVZ_CL762604_REV03_user_low_ship.tar.md5 is valid.
<OSM> CODE_I9000XWJVZ_CL762604_REV03_user_low_ship.tar.md5 is valid.
<OSM> GT-I9000-CSC-HOME-MULTI-OXAJVT.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/021> Odin v.3 engine (ID:21)..
<ID:0/021> File analysis..
<ID:0/021> SetupConnection..
<ID:0/021> Initialzation..
<ID:0/021> Set PIT file..
<ID:0/021> DO NOT TURN OFF TARGET!!
Thanks,
Ajay:crying:
Can you describe what happens when you attempt to turn on the phone?
Put a pit file,tick repartition and start again
Inviato dal mio GT-I9000 con Tapatalk 2
Stop any running KIES process while using Odin!
Related
After doing tons of research its clear to me that I have to flash a stock rom with odin. I have Odin 1.8.5 and the correct PDA, Phone and CSC files (I9000XXJVU_I9000OXAJVU_OXA) but when I try to reflash with repartition on nothing happens after this point:
Code:
<ID:0/004> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> CODE_I9000XXJVU_CL851880_REV03_user_low_ship.tar.md5 is valid.
<OSM> MODEM_I9000XXJVU_REV_00_CL1092175.tar.md5 is valid.
<OSM> GT-I9000-CSC-MULTI-OXAJVU.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/004> Odin v.3 engine (ID:4)..
<ID:0/004> File analysis..
<ID:0/004> SetupConnection..
<ID:0/004> Initialzation..
<ID:0/004> Set PIT file..
<ID:0/004> DO NOT TURN OFF TARGET!!
After doing more research I figured that I need to use Odin 1.8.3 with the 512 pit file, but that pit file is bloody impossible to find. Then I found another post that said I should reflash with dbdata.rfs.tar without repartition and no pit file but nothing happens after this:
Code:
<ID:0/004> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> MODEM_I9000XXJVU_REV_00_CL1092175.tar.md5 is valid.
<OSM> GT-I9000-CSC-MULTI-OXAJVU.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/004> Odin v.3 engine (ID:4)..
<ID:0/004> File analysis..
<ID:0/004> SetupConnection..
The vagueness of the information I have found is also extreamly frustrating, it seems there is no noob freindly information out there about this issue, no matter how much I search so please could someone give me some noob freindly information on how to do this.
Original problem is the E: Unknown Volume error after flashing to cm7 and them restoring backup if there is another method to fixing this
http://www.youtube.com/watch?v=1RoZU5ZPMS4&list=UUawwqTCK5egDfXdJe3EH0XQ&index=8&feature=plcp
CHECK THIS OUT
Issue has been resolved, I made the error of flashing the dbdata with the phone and csc files. Sorry about the useless post. Mod please lock/delete this thread
<ID:0/011> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> DefaultCalDataWithBoot_S5830iXXKK5_REV00.tar.md5 is valid.
<OSM> PDA_S5830iXXKL1_REV00.tar.md5 is valid.
<OSM> MODEM_S5830iXXKK5_REV00.tar.md5 is valid.
<OSM> GT-S5830i-MULTI-CSC-OXEKK4_RST.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/011> Odin v.3 engine (ID:11)..
<ID:0/011> File analysis..
<ID:0/011> SetupConnection..
I have been waiting but it didn't show anything for this stage. How should i do? I want to flash firmware. Please....
paingsis said:
<ID:0/011> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> DefaultCalDataWithBoot_S5830iXXKK5_REV00.tar.md5 is valid.
<OSM> PDA_S5830iXXKL1_REV00.tar.md5 is valid.
<OSM> MODEM_S5830iXXKK5_REV00.tar.md5 is valid.
<OSM> GT-S5830i-MULTI-CSC-OXEKK4_RST.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/011> Odin v.3 engine (ID:11)..
<ID:0/011> File analysis..
<ID:0/011> SetupConnection..
I have been waiting but it didn't show anything for this stage. How should i do? I want to flash firmware. Please....
Click to expand...
Click to collapse
Try uninstalling the drivers, reboot pc, install drivers again, stop any process of kies, then flash again. If not, try using a different usb cable. Some cable are crap LOL If not again, try using different usb ports.
paingsis said:
<ID:0/011> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> DefaultCalDataWithBoot_S5830iXXKK5_REV00.tar.md5 is valid.
<OSM> PDA_S5830iXXKL1_REV00.tar.md5 is valid.
<OSM> MODEM_S5830iXXKK5_REV00.tar.md5 is valid.
<OSM> GT-S5830i-MULTI-CSC-OXEKK4_RST.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/011> Odin v.3 engine (ID:11)..
<ID:0/011> File analysis..
<ID:0/011> SetupConnection..
I have been waiting but it didn't show anything for this stage. How should i do? I want to flash firmware. Please....
Click to expand...
Click to collapse
what odin verion that u use?? can u scroll down on page 1.. i have post how to flash via odin..
http://forum.xda-developers.com/showthread.php?t=1979814
A friend of mine has an SCH- I537 that justbstays in Download mode, he was trying to update it and something went wrong, so I looked on SamMobile and there are a lot of versions(Mexico Urugay etc) which one should I flash in Odin?
The phone is from AT&T
Thank you guys
Sent from my D2305 using XDA Free mobile app
Alfred1516 said:
A friend of mine has an SCH- I537 that justbstays in Download mode, he was trying to update it and something went wrong, so I looked on SamMobile and there are a lot of versions(Mexico Urugay etc) which one should I flash in Odin?
The phone is from AT&T
Thank you guys
Sent from my D2305 using XDA Free mobile app
Click to expand...
Click to collapse
Assuming you have the AT&T version of the i537, then look here: http://forum.xda-developers.com/showthread.php?t=2892445
Devo7v said:
Assuming you have the AT&T version of the i537, then look here: http://forum.xda-developers.com/showthread.php?t=2892445
Click to expand...
Click to collapse
thanksssssssssssssss
Alfred1516 said:
thanksssssssssssssss
Click to expand...
Click to collapse
Im having an issue that when Odin says selecting PIT its says FAILED and i can flash the stock rom, i need your help @Devo7v
PD: re-pratition wasnt checked
Alfred1516 said:
Im having an issue that when Odin says selecting PIT its says FAILED and i can flash the stock rom, i need your help @Devo7v
PD: re-pratition wasnt checked
Click to expand...
Click to collapse
Are you flashing the entire Odin package or are you just trying to flash a pit file? What firmware are you currently on and what firmware are you trying to flash? What steps are you taking that it's failing? Can you post the Odin log?
Devo7v said:
Are you flashing the entire Odin package or are you just trying to flash a pit file? What firmware are you currently on and what firmware are you trying to flash? What steps are you taking that it's failing? Can you post the Odin log?
Click to expand...
Click to collapse
Im fixing it and its not mine so i dont know which version it was running,
Today i itried with the Odin_I537UCUBML2.zip and i put the AP on PDA, BL on BOOTLOADER,
CP on Phone; the PIT on the PIT place and CSC on CSC and i got this:
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> BL_I537UCUBML2_2244695_REV06_user_low_ship_MULTI_CERT.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> AP_I537UCUBML2_2244695_REV06_user_low_ship_MULTI_CERT.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> CP_I537UCUBML2_2244695_REV06_user_low_ship_MULTI_CERT.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> CSC_ATT_I537ATTBML2_2244695_REV06_user_low_ship_MULTI_CERT.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/011> Added!!
<ID:0/011> Removed!!
<ID:0/011> Added!!
<ID:0/011> Odin v.3 engine (ID:11)..
<ID:0/011> File analysis..
<ID:0/011> SetupConnection..
<ID:0/011> Initialzation..
<ID:0/011> Set PIT file..
<ID:0/011> DO NOT TURN OFF TARGET!!
<ID:0/011> Get PIT for mapping..
<ID:0/011>
<ID:0/011> There is no PIT partition.
<OSM> All threads completed. (succeed 0 / failed 1)
I need your help ASAP @Devo7v
thanks
Second try wiith oficial samsung rom and same thng
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> I537UBUBNI1_I537TFGBNI1_I537UBUBNI1_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/011> Added!!
<ID:0/011> Odin v.3 engine (ID:11)..
<ID:0/011> File analysis..
<ID:0/011> SetupConnection..
<ID:0/011> Initialzation..
<ID:0/011> Set PIT file..
<ID:0/011> DO NOT TURN OFF TARGET!!
<ID:0/011> FAIL!
<ID:0/011>
<ID:0/011> Re-Partition operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)ry with Odin and
Alfred1516 said:
Second try wiith oficial samsung rom and same thng
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> I537UBUBNI1_I537TFGBNI1_I537UBUBNI1_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/011> Added!!
<ID:0/011> Odin v.3 engine (ID:11)..
<ID:0/011> File analysis..
<ID:0/011> SetupConnection..
<ID:0/011> Initialzation..
<ID:0/011> Set PIT file..
<ID:0/011> DO NOT TURN OFF TARGET!!
<ID:0/011> FAIL!
<ID:0/011>
<ID:0/011> Re-Partition operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)ry with Odin and
Click to expand...
Click to collapse
This last one you tried to flash is never going to work because it's not AT&T i537 Firmware. I would try flashing the NE3 Odin package, it's got the latest bootloader do it should work. Give it a shot and let me know.
Okey I will try to flash the I537UCUCNE3 full package then I will let you know thanks, do I need pit for this o no?
Did iI placed the files in the right order on Odin? @Devo7v
Sent from my D2305 using XDA Free mobile app
Alfred1516 said:
Okey I will try to flash the I537UCUCNE3 full package then I will let you know thanks, do I need pit for this o no?
Did iI placed the files in the right order on Odin? @Devo7v
Sent from my D2305 using XDA Free mobile app
Click to expand...
Click to collapse
I have no idea if you placed them in the right place, but it seems like you did. As long as you follow the instructions and it looks like the pictures you should be fine.
Okey I will, but the CP file goes to the Phone chart right?
But i will do it and i will let you know @Devo7v
Thanks
Sent from my D2305 using XDA Free mobile app
Alfred1516 said:
Okey I will, but the CP file goes to the Phone chart right?
But i will do it and i will let you know @Devo7v
Thanks
Sent from my D2305 using XDA Free mobile app
Click to expand...
Click to collapse
Bootloader = BL
PDA = AP
Phone = CP
CSC = CSC
I know you are having problems with the pit file, the CSC file in the Odin package contains the pit file, so if you're having problems with it maybe you have a corrupted download. Try downloading the package again and checking the MD5 against the one that is posted to ensure they match. Before you try the attached file I would try flashing the CSC file only, it should work.
In either case I've attached the NE3 pit file that I extracted from the Odin package. I'm not sure which slot this needs to be flashed in, but be careful because this could brick your phone. This file cannot be flashed through the phone's recovery, you must extract the zip and flash the pit file inside through Odin.
I placed everything on its place and got the same error.......... Im giving up with this @Devo7v
<ID:0/011> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> BL_I537UCUCNE3_987011_REV06_user_low_ship_MULTI_CERT.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> AP_I537UCUCNE3_987011_REV06_user_low_ship_MULTI_CERT.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> CP_I537UCUCNE3_987011_REV06_user_low_ship_MULTI_CERT.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> CSC_ATT_I537ATTCNE3_987011_REV06_user_low_ship_MULTI_CERT.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/011> Odin v.3 engine (ID:11)..
<ID:0/011> File analysis..
<ID:0/011> SetupConnection..
<ID:0/011> Initialzation..
<ID:0/011> Set PIT file..
<ID:0/011> DO NOT TURN OFF TARGET!!
<ID:0/011> FAIL!
<ID:0/011>
<ID:0/011> Re-Partition operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
Alfred1516 said:
I placed everything on its place and got the same error.......... Im giving up with this @Devo7v
<ID:0/011> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> BL_I537UCUCNE3_987011_REV06_user_low_ship_MULTI_CERT.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> AP_I537UCUCNE3_987011_REV06_user_low_ship_MULTI_CERT.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> CP_I537UCUCNE3_987011_REV06_user_low_ship_MULTI_CERT.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> CSC_ATT_I537ATTCNE3_987011_REV06_user_low_ship_MULTI_CERT.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/011> Odin v.3 engine (ID:11)..
<ID:0/011> File analysis..
<ID:0/011> SetupConnection..
<ID:0/011> Initialzation..
<ID:0/011> Set PIT file..
<ID:0/011> DO NOT TURN OFF TARGET!!
<ID:0/011> FAIL!
<ID:0/011>
<ID:0/011> Re-Partition operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
Click to expand...
Click to collapse
It's definitely the AT&T version of the i537 and not the TelCel or Uruguayan version, correct?
It says AT&T on the back cover, is there any other way to confirm that is from AT&T? @Devo7v
Sent from my D2305 using XDA Free mobile app
Alfred1516 said:
It says AT&T on the back cover, is there any other way to confirm that is from AT&T? @Devo7v
Sent from my D2305 using XDA Free mobile app
Click to expand...
Click to collapse
Check the sticker under the battery as well.
It says SGH-i537
Sent from my D2305 using XDA Free mobile app
Alfred1516 said:
It says SGH-i537
Sent from my D2305 using XDA Free mobile app
Click to expand...
Click to collapse
I think you have a bad download then. Try downloading the NE3 package again and try a different version of Odin, 3.07 or 3.09.
Thanks for your help but my friend says he will buy another Mother board or sell the phone, but thanks! a lot
Sent from my D2305 using XDA Free mobile app
it's an sgh-i537
I'm not experienced in this sort of stuff, but I think my phone is considered "soft bricked"
I can boot it into recovery mode/download mode, but when I go into download mode, odin wont recognize it.
on top of that, when/if I am able to get it to recognize my phone, to my understanding I need to know what MF# I'm running- and I have absolutely no clue what that is. A bit of reading leads me to believe it means Manifest or something like that, but I still have no clue what one I have.
please help an idiot.
magapower said:
it's an sgh-i537
I'm not experienced in this sort of stuff, but I think my phone is considered "soft bricked"
I can boot it into recovery mode/download mode, but when I go into download mode, odin wont recognize it.
on top of that, when/if I am able to get it to recognize my phone, to my understanding I need to know what MF# I'm running- and I have absolutely no clue what that is. A bit of reading leads me to believe it means Manifest or something like that, but I still have no clue what one I have.
please help an idiot.
Click to expand...
Click to collapse
What you're referring to as MF# is actually the last three characters in the firmware build number, which we use to differentiate between different firmware builds. To fix your phone, you have to use Odin v3.09 to restore a stock firmware. Download this file and extract all 4 files within. You have to use all 4 files in Odin, it'll look like this:
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
(I know the picture has Odin v3.07 but I've always had success with 3.09). The process will take some time, you must be patient and let it do its thing. When you do this, your phone will automatically reboot on its own a couple times, and one of those times will be to the stock android recovery. This is completely normal. I say this because I've seen so many people freak out when their phone starts doing stuff on its own. Just let Odin go, it knows what it's doing.
I finally got odin to recognize my phone, and I used files you linked to and the top left box turned red and said "Fail!"
In the Messages box...
<ID>:0/003>Initialization..
<ID>:0/003>Set PIT file..
<ID>:0/003>DO NOT TURN OFF TARGET!!
<ID>:0/003>Complete(write) operation failed.
<OSM> All Threads completed. (succeed 0 / failed 1)
<ID>:0/003> Removed!!
<ID>:0/003>Added!!
I would just post a picture, but I'm a new user.
edit:
tried using odin 3.07 and just the AP file, I noticed it added something in the messages...
<ID:0/003> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> AP_I537UCUBML2_2244695_REV06_user_low_ship_MULTI_CERT.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Get PIT for mapping..
<ID:0/003> There is no PIT partition.
<OSM> All threads completed. (succeed 0 / failed 1)
I'm looking at that "There is no PIT partition... thoughts on that?
What android you had after softbrick ... because that file ML2 Firmware is Jellybean if your system kitkat you can't go back to Jellybean or if your System lollipop you can't go back to Kitkat make sure what android is you current system puls check your usb cable.. notes.. if you used to be on lollipop and software brick there's no Lollipop file Odin flash file available on xda only available jellybean and kitkat.. you need to take your phone to best buy you will see Samsung section just tell them I want to flash my phone they will help you ....
Sent from my SAMSUNG-SGH-I537 using XDA Free mobile app
---------- Post added at 10:06 AM ---------- Previous post was at 10:03 AM ----------
Check your usb cable and flash kitkat 4.4.2 Odin files if is failing take your phone to best buy and flash lollipop
Sent from my SAMSUNG-SGH-I537 using XDA Free mobile app
I believe It was 4.2.2 Jellybean. (with AT&T)
I tried to update it to lollipop when this started.
I'm still looking into the whole PIT thing, and even found a download for a PIT file for the i537 but haven't done anything with it yet because stuff I've read say thats more for the development stuff and could really mess up your phone.
magapower said:
I believe It was 4.2.2 Jellybean. (with AT&T)
I tried to update it to lollipop when this started.
I'm still looking into the whole PIT thing, and even found a download for a PIT file for the i537 but haven't done anything with it yet because stuff I've read say thats more for the development stuff and could really mess up your phone.
Click to expand...
Click to collapse
You are flashing the wrong Odin file. You need to flash the files that @thisisapoorusernamechoice linked to. You should be flashing all 4 files at once otherwise you're going to end up with a phone that doesn't work properly.
Devo7v said:
You are flashing the wrong Odin file. You need to flash the files that @thisisapoorusernamechoice linked to. You should be flashing all 4 files at once otherwise you're going to end up with a phone that doesn't work properly.
Click to expand...
Click to collapse
I have been flashing with all 4. on various different Odin versions with different firmware versions.
magapower said:
I have been flashing with all 4. on various different Odin versions with different firmware versions.
Click to expand...
Click to collapse
As was mentioned before, it looks like you're flashing the wrong files. You've flashed ML2 firmware which is why it fails to flash all 4 files. You need to be flashing all 4 NE3 files.
alright, a little headway... I tried all 4 files on odin 3.10 and got further...
<ID:0/003> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> BL_I537UCUBML2_2244695_REV06_user_low_ship_MULTI_CERT.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> AP_I537UCUBML2_2244695_REV06_user_low_ship_MULTI_CERT.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> CP_I537UCUBML2_2244695_REV06_user_low_ship_MULTI_CERT.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> CSC_ATT_I537ATTBML2_2244695_REV06_user_low_ship_MULTI_CERT.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Odin engine v(ID:3.1005)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Set PIT file..
<ID:0/003> DO NOT TURN OFF TARGET!!
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> SingleDownload.
<ID:0/003> sbl1.mbn
<ID:0/003> NAND Write Start!!
<ID:0/003> sbl2.mbn
<ID:0/003> sbl3.mbn
<ID:0/003> rpm.mbn
<ID:0/003> aboot.mbn
at the moment my phone is still plugged in and odin is just hanging on aboot.
thoughts?
magapower said:
alright, a little headway... I tried all 4 files on odin 3.10 and got further...
<ID:0/003> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> BL_I537UCUBML2_2244695_REV06_user_low_ship_MULTI_CERT.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> AP_I537UCUBML2_2244695_REV06_user_low_ship_MULTI_CERT.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> CP_I537UCUBML2_2244695_REV06_user_low_ship_MULTI_CERT.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> CSC_ATT_I537ATTBML2_2244695_REV06_user_low_ship_MULTI_CERT.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Odin engine v(ID:3.1005)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Set PIT file..
<ID:0/003> DO NOT TURN OFF TARGET!!
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> SingleDownload.
<ID:0/003> sbl1.mbn
<ID:0/003> NAND Write Start!!
<ID:0/003> sbl2.mbn
<ID:0/003> sbl3.mbn
<ID:0/003> rpm.mbn
<ID:0/003> aboot.mbn
at the moment my phone is still plugged in and odin is just hanging on aboot.
thoughts?
Click to expand...
Click to collapse
Stop using ML2 and use the NE3 files I linked to
thisisapoorusernamechoice said:
Stop using ML2 and use the NE3 files I linked to
Click to expand...
Click to collapse
I tried them, with odin 3.04, 3.06, 3.07, 3.09 and 3.10 and it kept failing right away.
also now the other files aren't getting as far as they did before.
also minor development- for the first time, when I tried to go into download mode, it popped up the "Firmware upgrade encounter an issue. please select recovery mode in kies and try again" screen.
aaaand now even the files that looked like they might work aren't doing ****.
magapower said:
I tried them, with odin 3.04, 3.06, 3.07, 3.09 and 3.10 and it kept failing right away.
also now the other files aren't getting as far as they did before.
also minor development- for the first time, when I tried to go into download mode, it popped up the "Firmware upgrade encounter an issue. please select recovery mode in kies and try again" screen.
aaaand now even the files that looked like they might work aren't doing ****.
Click to expand...
Click to collapse
You're flashing the wrong files. The only way you're going to get this to work is if you flash the NE3 files. You have to make them work. Try downloading it again and check the MD5 to make sure you didn't get a corrupted download.
alright, just put it to rest, I am using the files I was linked to, I did check the md5.
I tried all the following just a few minutes ago
Odin 3.10 (yes running as admin)
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> BL_I537UCUCNE3_987011_REV06_user_low_ship_MULTI_CERT.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> AP_I537UCUCNE3_987011_REV06_user_low_ship_MULTI_CERT.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> CP_I537UCUCNE3_987011_REV06_user_low_ship_MULTI_CERT.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> CSC_ATT_I537ATTCNE3_987011_REV06_user_low_ship_MULTI_CERT.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Set PIT file..
<ID:0/003> DO NOT TURN OFF TARGET!!
<ID:0/003> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
<ID:0/003> Removed!!
<ID:0/003> Added!!
Odin 3.09 (yes running admin)
<ID:0/003> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> BL_I537UCUCNE3_987011_REV06_user_low_ship_MULTI_CERT.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> AP_I537UCUCNE3_987011_REV06_user_low_ship_MULTI_CERT.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> CP_I537UCUCNE3_987011_REV06_user_low_ship_MULTI_CERT.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> CSC_ATT_I537ATTCNE3_987011_REV06_user_low_ship_MULTI_CERT.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Set PIT file..
<ID:0/003> DO NOT TURN OFF TARGET!!
<ID:0/003> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
<ID:0/003> Removed!!
<ID:0/003> Added!!
Odin 3.07 (yes running admin)
<ID:0/003> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> BL_I537UCUCNE3_987011_REV06_user_low_ship_MULTI_CERT.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> AP_I537UCUCNE3_987011_REV06_user_low_ship_MULTI_CERT.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> CP_I537UCUCNE3_987011_REV06_user_low_ship_MULTI_CERT.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> CSC_ATT_I537ATTCNE3_987011_REV06_user_low_ship_MULTI_CERT.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
<ID:0/003> Removed!!
<ID:0/003> Added!!
Odin 3.06 (yes running admin)
<ID:0/003> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> BL_I537UCUCNE3_987011_REV06_user_low_ship_MULTI_CERT.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> AP_I537UCUCNE3_987011_REV06_user_low_ship_MULTI_CERT.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> CP_I537UCUCNE3_987011_REV06_user_low_ship_MULTI_CERT.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Set PIT file..
<ID:0/003> DO NOT TURN OFF TARGET!!
<ID:0/003> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
<ID:0/003> Removed!!
<ID:0/003> Added!!
Odin 3.04 (yes running in admin)
<ID:0/003> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> BL_I537UCUCNE3_987011_REV06_user_low_ship_MULTI_CERT.tar.md5 is valid.
<OSM> AP_I537UCUCNE3_987011_REV06_user_low_ship_MULTI_CERT.tar.md5 is valid.
<OSM> CP_I537UCUCNE3_987011_REV06_user_low_ship_MULTI_CERT.tar.md5 is valid.
<OSM> CSC_ATT_I537ATTCNE3_987011_REV06_user_low_ship_MULTI_CERT.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Set PIT file..
<ID:0/003> DO NOT TURN OFF TARGET!!
<ID:0/003> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
<ID:0/003> Removed!!
<ID:0/003> Added!!
I'm wondering if I should try harder using Kies? I can't get kies to connect to my phone (it just hangs on the connecting screen), and when I try to manually input my phone (where you put in the model and S/N), it gives me the message saying that my phone can't be verified.
update to this:
after leaving the phone alone for a week, I decided to give it another go and was somewhat successful I think. This is what happened.
<ID:0/003> Removed!!
<ID:0/003> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> BL_I537UCUCNE3_987011_REV06_user_low_ship_MULTI_CERT.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> AP_I537UCUCNE3_987011_REV06_user_low_ship_MULTI_CERT.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> CP_I537UCUCNE3_987011_REV06_user_low_ship_MULTI_CERT.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> CSC_ATT_I537ATTCNE3_987011_REV06_user_low_ship_MULTI_CERT.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Set PIT file..
<ID:0/003> DO NOT TURN OFF TARGET!!
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> SingleDownload.
<ID:0/003> sbl1.mbn
<ID:0/003> NAND Write Start!!
<ID:0/003> sbl2.mbn
<ID:0/003> sbl3.mbn
<ID:0/003> rpm.mbn
<ID:0/003> aboot.mbn
<ID:0/003> tz.mbn
<ID:0/003> boot.img
<ID:0/003> recovery.img
<ID:0/003> persdata.img.ext4
<ID:0/003> system.img.ext4
<ID:0/003> modem.bin
<ID:0/003> Transmission Complete..
<ID:0/003> Now Writing.. Please wait about 2 minutes
<ID:0/003> Receive Response from boot-loader
<ID:0/003> NON-HLOS.bin
<ID:0/003> Transmission Complete..
<ID:0/003> Now Writing.. Please wait about 2 minutes
<ID:0/003> Receive Response from boot-loader
<ID:0/003> cache.img.ext4
<ID:0/003> RQT_CLOSE !!
<ID:0/003> RES OK !!
<ID:0/003> Removed!!
<ID:0/003> Remain Port .... 0
<OSM> All threads completed. (succeed 1 / failed 0)
now instead of automatically booting to the "connect to keis" screen, it goes to the Samsung S4 active screen and just hangs there.
I can still enter download mode.
Doesn't seem like I can ever recovery mode though. any thoughts on how to progress?
Thanks.
I am trying to root Lollipop on my I537 so I flashed back to KK successfully. Towelroot is successful so I flash LP as instructed using Flashfire but I never got rebooted to download mode. I get stuck on the S4 Active boot screen and the device seems to power down. So I boot to download mode manually and flashed the I537_OC7_Bootloader using odin but still cant get past the Active Boot screen. So I am trying to flash back to KK again. I was able to do this before last night but today I can't seem to get the firmware to flash! Can some one help me?
Code:
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> BL_I537UCUCNE3_987011_REV06_user_low_ship_MULTI_CERT.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> AP_I537UCUCNE3_987011_REV06_user_low_ship_MULTI_CERT.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> CP_I537UCUCNE3_987011_REV06_user_low_ship_MULTI_CERT.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> CSC_ATT_I537ATTCNE3_987011_REV06_user_low_ship_MULTI_CERT.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/004> Odin v.3 engine (ID:4)..
<ID:0/004> File analysis..
<ID:0/004> SetupConnection..
<ID:0/004> Initialzation..
<ID:0/004> Set PIT file..
<ID:0/004> DO NOT TURN OFF TARGET!!
<ID:0/004> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
<ID:0/004> Removed!!
<ID:0/004> Added!!
When I try to flash the I537_OC7_Bootloader it says no pit partition found:
Code:
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> CWM-Recovery-gt-i9295_v1-2.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/004> Odin v.3 engine (ID:4)..
<ID:0/004> File analysis..
<ID:0/004> SetupConnection..
<ID:0/004> Initialzation..
<ID:0/004> Get PIT for mapping..
<ID:0/004> There is no PIT partition.
<OSM> All threads completed. (succeed 0 / failed 1)
<ID:0/004> Removed!!
<ID:0/004> Added!!
Ok so I got Odin to flash everything from SGH-I537UCUCNE3_v4.4.2_ATT_ALL and even a pit file i found here. Problem is I get the S4A boot screen and it says booting recovery in blue at the top right but then it dies. Any Ideas? I got Odin to flash by using a USB port on back of my PC on the mobo rather then the front USB ports on the case.
I also do not have access to stock recovery even after a successful NE3 flash with Odin! Have I bricked my device or just soft bricked it?
Anyone?