Database Develop

[Q] HELP ME XDA you're my only hope... Galaxy Freezing!

Hi guys,
Hoping someone can help me.
I attempted to flash my ROM with Darkys, but my Galaxy S didn't play ball and stopped booting.
So I followed the usual steps to get it back via odin.
Procedure:
1.Open ODIN. (And close Kies, if you have it open. It is important to have ODIN open BEFORE connection the phone via USB!)
2.Select the PDA/Modem/CSC/.PIT files in Odin. (.PIT and PDA are required. CSC and Modem are HIGHLY recommended. They may be necessary depending on the PDA! Try flashing all three BEFORE reporting bugs, if you only used one initially!)
3.Check the "Re-Partition" checkbox.
4.Turn the phone into the download mode by pressing and holding VolumeDown+Home+Power.
5.Connect your phone with your computer and wait until the drivers are installed.
6.When the drivers are installed, click Start.
7.The phone will be flashed and once it’s finished, it will boot up. (Do NOT disconnect the usb-cable, remove the battery or otherwise interrupt this process!)
8.You have successfully flashed your phone.
Now, It worked yesterday and all was good, but as you know Eclair is powerfully S*%t So I tried reflashing darkys from the Clockworldmod, and this also killed the phone preventing it from booting.
After this I could not access recovery mode.. only Download mode.
Rinse and repeat the steps above... Sadly now once my phone goes to reboot after reflash in Odin, it freezes on the white rotating circles.. and doesn't progress. as mentioned above, I can only get into Download mode.
My Galaxy is a GT-i9000 (Australian Optus).
Can someone please help?? I've looked around but can't find a fix.
If you can help me out that would be Awesome..

Since you are using eclair, I would suggest first upgrading to a stock froyo (there is a froyo upgrade guide in general) and if that works try darkyys rom.
Sent from my GT-I9000 using Tapatalk

Flashed xx rom twice and it broke your phone . Lesson learnt ???.
Go to Rom Kitchen and download a rom to your build and flash .
http://romkitchen.org/sgs/?s=home
http://forum.xda-developers.com/showthread.php?t=817703
First you may need to flash a clean setup
Block 2 Odin method .
http://forum.xda-developers.com/showthread.php?t=818556
jje

[Q] Would you tell me my I9000 dead not just dying....

Thanks in advance for any response!
The followings are my phone's symthoms:
1. My phone WAS FANTASTIC until I updated new Darky extreme version 9.2 (upgrade from 9.0)
2. I degraded it to the stock rom with Ryan's OLFG -> Working very well...
3. Until the phone was restarted. The phone was still working however
4. IT BECAME FREEZING. I couldnt scroll, couldnt touch the screen, or the phone response was like 5 mins later for each touch.
5. I followed instructions on the internet to flash with stock rom (JM8) and upgraded it to JPO, and the result is
6. THE PHONE COULDNT BE BOOTED at the Galaxy logo.
7. I tried to flash the phone over and over with different stock roms using ODIN 1.3 (with well understanding about repartition and PIT)
8. NOW, my phone is still able to access the download mode, but my PC CANNT SEE THE PHONE DRIVER ANYMORE(tested on 3 other laptops with the same result)
9. Reinstall USB drivers like 20 times, the results have been the same.
TO me this should be a phone death. Im gonna purchase the new Galaxy S 2
HOWEVER, If there is anyway to revive my phone back to normal (Cuz I wanna get some important data in the internal card), I will not only send a big gratitude but some DONATE as well.
Thanks.

so you put the phone in download mode first... then you attach the USB ???
Does anything happen when your in Odin ?? does it not say connected or anything ??
and have you tried doing a factory reset in recovery mode ??
aslong as your phone can go into download mode there is still hope so dont give up on it just yet

U obv have samsung kies right?. Go on processes on ur pc ctrl alt del n kill the kiestrayagent process
Sent from my GT-I9000 using XDA App

Surely I killed KS before doing ODIN. The PC(s) said it was Unknown device.
My phone was on when android 2.1 installed (but freezing, not just lagging .... completely freezing on the home screen) and would not boot if i installed 2.2
Sigh....
Thanks for your replies

The PC(s) said it was Unknown device.
Thats generally a USB /driver/windows problem .
You installed deadlys rom and it should still be recoverable even from that .
Is your phone picked up via Kies phone/Odin will need Kies installed .
I would have flashed back to a clean copy of Eclair first off to get the phone working .
jje

Both Kies and Odin could not see my phone... I killed Kies process before doing Odin, but the result was still a sadness.

[Q] Captivate Soft Brick - Need a rooted Odin solution.

Hi
My brother (a no-geek) has a captivate, and lives in a different city (I donot have physical access to the phone). He visited me few weeks ago and I installed CM-7 on his phone, i know my bad. Some of his videos were not working, so i asked him to update to the latest CM-7 build. He download the build, saved it on int sd_card and used ClockWork Recovery to install the selected ROM. Upon reboot it entered in never-ending splash screen. I found couple of odin ROMs, and posted him link, we tried to flash them, but no good.
Status --
The COM ports are detected, but the process at times halts at <SET PARTITION> at times at <SET UP>... at times all thread completed successful would show up as soon as hitting START.
I dont have a captivate, can someone please suggest a sure shot solution and post me a link for ODIN, with a root rom. I am using Team Whiskey on my Vibrant, and I prefer stable modified ROM because of its features and power.
I can explain him the process on skype using desktop sharing, but the ROM should be good. Thankyou very much in advance.

if he can access recovery, try wiping everything thru recovery then start again

Phone is in Soft Brick state.
Phone is in Soft Brick state. So i cannot boot into the phone and go to CW recovery.

What he needs is just a stable usb connection that's how he got to this point, bad communication between the phone and computer. On cm7 I beleive you need the nexus s drivers installed. Also make sure it's plugged into a usb port that's attached directly to the motherboard (back of pc, port 1 on laptop)

@studacris
I think the drivers are already installed good. The connection is also good, as i can the COM port detection in the ODIN, with one of the boxes changing its colour from NO-COLOUR to YELLOW-COLOUR.
I think the ROM builds are not good. They go action-less during flashing, actually nothing (progress bar) comes on phone, it keeps showing the Downloading screen, endlessly. Odin usually is stuck at at <SET PARTITION> at times at <SET UP>...
Can someone post a link for a test one click odin. Well i would prefer one click.

You did try DG's JF6 one click, thats the only one I use, how are you establishing dowload mode on the phone or are you even doing this.

REMY4223 said:
I would suggest to Odin back to stock then update to Froyo via Kies.
Click to expand...
Click to collapse
if you could do all that, why would you need to send back for a new phone ? If you could do any of that, the OP wouldn't be in a non-functioning predicament

Ragin Caucasian said:
if you could do all that, why would you need to send back for a new phone ? If you could do any of that, the OP wouldn't be in a non-functioning predicament
Click to expand...
Click to collapse
+1 If you read the OP the problem is he can't flash back to stock he is having problems flashing anything period, @ the OP correct me if I'm wrong but I have a strong hunch that you are leaving out some pretty crucial steps, I have a feeling that you are not putting the phone into download mode, I also believe that you are gonna need to make a jig and pay a visit to your brother to help him out especially if its bricked the same way mine just was flashing with cm7 roms. But if you are getting a com port to show without having to put in download mode then you are farther along in the boot process. If this is the case you may be able to adb into recovery do a full wipe excluding /boot and reflash. Will the PC recognize the phone with it in its current boot locked state? If so then recovering should be somewhat of a breeze.
http://forum.xda-developers.com/showthread.php?t=829392 read this post it may help otherwise there are tons others

- I am getting to downloading mode by
--- pressing the "vol +" and "vol -" buttons and then connecting the usb cable to the computer.
--- then removing the cable, after the phone enters the download mode. Then, start the odin and connect the phone through usb cable again. The odin detects the phone on one of the COM port.
- I havent tired wiping the phone through recovery. But i need to get to recovery first. I dont know in a soft brick state if i can get into recovery.
- regarding getting back to 2.1... i would like to flash to the latest version. Kies update is not an option for me, as i not in US.
This phone was purchased from craiglist, i used one click root method to root it and the same script an option to get the unlock codes. After that i experimented a lot on the phone with various scripts. Last i was using congnition on it. Then saw CM7, i liked it on my vibrant, so i flashed it on my captivate (which i got for my brother). Now i have to get back to some stable modified ROM... I am thinking about trying Srendipity or cog ROM... but before than i have to install a rooted stock ROM.
That is the story and issue... but thanks a lot for help. Any more suggestions.

viveksharma2108 said:
- I am getting to downloading mode by
--- pressing the "vol +" and "vol -" buttons and then connecting the usb cable to the computer.
--- then removing the cable, after the phone enters the download mode. Then, start the odin and connect the phone through usb cable again. The odin detects the phone on one of the COM port.
- I havent tired wiping the phone through recovery. But i need to get to recovery first. I dont know in a soft brick state if i can get into recovery.
- regarding getting back to 2.1... i would like to flash to the latest version. Kies update is not an option for me, as i not in US.
This phone was purchased from craiglist, i used one click root method to root it and the same script an option to get the unlock codes. After that i experimented a lot on the phone with various scripts. Last i was using congnition on it. Then saw CM7, i liked it on my vibrant, so i flashed it on my captivate (which i got for my brother). Now i have to get back to some stable modified ROM... I am thinking about trying Srendipity or cog ROM... but before than i have to install a rooted stock ROM.
That is the story and issue... but thanks a lot for help. Any more suggestions.
Click to expand...
Click to collapse
Try putting the phone into download mode after you open Odin. Which version of Odin is this? Also, installing the nightly build of CM7 again often fixes the boot loop on the newer builds. I would try that if you can get to recovery.
Sent from my SGH-I897 using XDA Premium App

[Q] Messed it up and need help

This WAS the situation before the problems:
Rooted Gingerbread rom, all working fine. Decided to unroot and install the full version of the official German ICS rom by using PC Odin. All went fine and used my Note for over two days. Because of the lags en slow responses I decided to reflash the ICS rom. From that moment on I messed it up. I've been reading and searching hundreds of posts for almost a day but didn't find a solution.
This IS the current situation:
I can get into download mode
I can get in recovery mode
However, in recovery mode I can not install a rom, every flash (CWM, both ICS and GB - even using chainfire's rom needed for rooting) stops on a random moment...but never gets it to the end, even if I wait several hours. Installing is very...very....very slow.
In recovery mode i can not restore a Nandroid backup, both ICS and GB. Every backup stops when /system has te be installed. errormessage.
In download mode I can connect my Note to PC Odin. I can select a rom and start flashing. However, after appr. 80% installation halts during "nand write start", no error message. The flashing does not finish, even after hours.
Funny is, i can install a kernel like Abyss.
So, I can't restore, i can't flash using cwm in recovery and I can't flash using PC Odin. My device seems not fully bricked. The max I get when rebooting (knowing that the process has not finished) is the triangle screen.
Any advise is appreciated.

Do not flash thru CWM... Flash a good GB kernel like "franco.Kernel" but thru PC Odin then u can flash whatever u want from franco's CWM... Good luck

Don't need help anymore
Note is officially bricked. After several attempts to recover from a softbrick the screen of my Note didn't turn on anymore. No button or button combination works, no recovery and no download mode, just a black screen.

Ce said:
Don't need help anymore
Note is officially bricked. After several attempts to recover from a softbrick the screen of my Note didn't turn on anymore. No button or button combination works, no recovery and no download mode, just a black screen.
Click to expand...
Click to collapse
Flat battery? It's also possible that it's just the screen that's not working. Try entering download mode "blind". So hold power+home+vol down for ~10 seconds, then press vol up. Hook it up via usb and see if Odin can recognize it.

Thanks, didn't think of that. But unfortunately no response from the device.

So now that it looks like your phone is officially bricked, I think you should just take it to Samsung and make up a story. Like you were updating your software with Kies and something happened and the phone is just not booting up.
I am sorry you bricked your note though..

try AMORA Filemanager.. flash via recovery and you have a file manager,,, take a look on your partitions
just my idea, you got nothing to lose

musashiro said:
try AMORA Filemanager.. flash via recovery and you have a file manager,,, take a look on your partitions
just my idea, you got nothing to lose
Click to expand...
Click to collapse
I would like to but it's very hard when you can't see anything on the screen...

Maybe it's just the battery, try to charge it externally and try a JIG also
Sent from my GT-N7000 using XDA

Just a quick, final, update.
My Note was superbricked. Had to send it to a Samsung Service Center. No additional questions were asked. Samsung replaced the mainboard. Didn't have to pay anything.
Great service!!!

try this out buddy, do it on your own risk!!! anyways you have messed it up.
Ce said:
This WAS the situation before the problems:
Rooted Gingerbread rom, all working fine. Decided to unroot and install the full version of the official German ICS rom by using PC Odin. All went fine and used my Note for over two days. Because of the lags en slow responses I decided to reflash the ICS rom. From that moment on I messed it up. I've been reading and searching hundreds of posts for almost a day but didn't find a solution.
This IS the current situation:
I can get into download mode
I can get in recovery mode
However, in recovery mode I can not install a rom, every flash (CWM, both ICS and GB - even using chainfire's rom needed for rooting) stops on a random moment...but never gets it to the end, even if I wait several hours. Installing is very...very....very slow.
In recovery mode i can not restore a Nandroid backup, both ICS and GB. Every backup stops when /system has te be installed. errormessage.
In download mode I can connect my Note to PC Odin. I can select a rom and start flashing. However, after appr. 80% installation halts during "nand write start", no error message. The flashing does not finish, even after hours.
Funny is, i can install a kernel like Abyss.
So, I can't restore, i can't flash using cwm in recovery and I can't flash using PC Odin. My device seems not fully bricked. The max I get when rebooting (knowing that the process has not finished) is the triangle screen.
Any advise is appreciated.
Click to expand...
Click to collapse
i was not a member when i commited this mistake. but then big thanks to this community it helped me back from softbrick.
first you do is install a stock kernel of ics on your note go into recovery and just clear cache partition, thats it no wipe/data factory reset.
then,
install the pit file from this thread, also read it completely before proceeding. http://forum.xda-developers.com/show....php?t=1667886 , hoping yours is 16gb version and also read this thread for additional info but its quite complicated for me so im just telling you the direct method and hopefully itll get your note back to work. so once you download the 16gb pit file unzip it and in the unzip folder you will find a separately lying pit of 16gb stating patched-standard thats the one you want.
then,
goto samfirmware and download the latest ics firmware(i downloaded the indian one as it is in file .tar),
unzip it till you get .tar file.
open odin- click pit-select 16gb patched standard pit- check wether repartion is ticked- click pda-select the .tar file you extracted connect your phone and start. this time i wont stop at factory.fs.....
NOTE THAT AFTER THIS PROCEDURE IS COMPLETED SUCCESSFULLY YOUR INTERNAL STORAGE WOULD BE ONLY 8GB INSTEAD OF 11 GB STOCK WHICH YOU WERE GETTING.
I REVIVED MY NOTE THROUGH THIS PROCEDURE. PROCEES AT YOUR OWN RISK.
one your phone is working you'll be able to reset the counter with a jig and get your phone under warranty and get your motherboard changed by teliing at the Samsung Service that you are getting only 8gb instead of 11gb you used to get earlier(warranty only if you had any).
hope this helps mate.
BEST OF LUCK!!
A BIG HUGE THANKS TO hg42.....

[Q] stable custom rom for mini2?

Hi everybody,
sorry for posting this outside the mini 2 forum, but appearently that's a developers reserved forum, so I had no rights to post there.
I would like to ask what is the latest stable custom rom developed for mini2, where to find it and possibly an instruction page.
I had good experience with CM on another galaxy before, so I checked on the the CM website first but mini 2 is not listed there
On the other end I saw a long post on the mini2 developers forum saying that CM10 was actually created, but the post is 91 pages long(!), so forgive me if I didn't read it all. Is it working?
I also checked if there was something like an "in evidence" post with instructions for newbies but couldn't see any, maybe I missed it.
Can someone point me to the right page?
thank you for your held
davide

mm in the meantime I screwed things up. I installed gapps and now it only boots in recovery mode...
why? what shall I do?
please help
thank you
davide

ok, now I'm starting to panic.
why does nobody answer, am I doing something wrong with this post?
I reinstalled the stock rom. I first tried using CWM recovery and selecting install zip file from sd card, but it didn't work: it told me BAD regarding the zip file (downloaded from sammobile), then I succeded using odin. by the way which is the correct method?
However it now seems to start, but I get in loops messages from the setupwizard that says the guided configuration has crashed and also from gapps that Google service Framework has crashed (but should gapps be wiped by the rom flash???).
the problem is that the first of the two keeps restarting and crashing so the phone doesn't do anything else then showing this messages.
please help
davide

After you flash Stock ROM via Odin. Remove battery, put it back. Boot into stock recovery - clear user data & cache and reboot. If the same error occurs try deleting /Android directory(old cache) in your sd card.

thank you for your reply, unfortunately it didn't help.
what do you mean by "stock recovery"? the recovery I see, I believe is CWM which I installed before, but I'm not sure.
anyhow from there I wiped user&cache but I had tried this before and removing teh battery didn't make a difference.
I do not have any /Android directory on my SD card.
it's a simple 4GB fat 32 partition with a single file in it (the zip with stock rom I tried to flash before using odin) and nothing else.

by the way, I used odin3 v.1.83 to flash and I selected the file using PDA button,
but I also have "bootloader", "phone" and "csc" options.
what is the difference?

everything I do makes it more dramatic!
I tried reapeating the whole procedure once again, and odin crashed while flashing teh rom. now it doesn't even boot in download mode, it simply asys to connect kies in recovery mode. but kies never saw my phone in spite of driveres reinstallation, and it is of course not seeing it now!!

yukdav said:
everything I do makes it more dramatic!
I tried reapeating the whole procedure once again, and odin crashed while flashing teh rom. now it doesn't even boot in download mode, it simply asys to connect kies in recovery mode. but kies never saw my phone in spite of driveres reinstallation, and it is of course not seeing it now!!
Click to expand...
Click to collapse
you should terminate kies before using odin. You can kill it in task manager, because kies intereferes with ODIN.
You should'nt be concerned with bootloader and the other options. As long as ur downloaded stock has tar.md5 extension you just place it in the PDA section and select Auto reboot and F. Reset time only.
Also You should only disconnect when it says PASS otherwise u will brick ur phone.
When u success fully flash ur stock rom, the chance is it will not get to homescreen
So u remove battery, reinsert it, press and hold HOME button together with POWER button, the phone boots into stock recovery, you choose wipe data and cache, then reboot. (chemicalrage explained this)
If it ain't booting into download mode u should go to service centre.
PS: My advice is to stay away from custom roms until samsung releases jelly bean for mini 2, then better custom roms will be released.