I9305 stucked whili upgrading with Kies - Galaxy S III I9305 (4G LTE + 2GB RAM) Q&A, Help &

I bought ı9305 yesterday.(This is my first android device.I'm a noop.)Today I connect my phone to pc.Kies said there was an update would you like to update.I tried to update but it stucked.Then I removed the battery.I tried to turn on my phone and a message appeared ''firmware upgrade encountered an issue. please select recovery mode in kies and try again'' I tried emergency firmware recover tool on kies but ıt always stuck on %2
(sorry for my english if there is a mistake)

read the basics first, then flash a stock rom via Odin if stock is good enough for you

Glebun said:
read the basics first, then flash a stock rom via Odin if stock is good enough for you
Click to expand...
Click to collapse
where can ı download stock rom for my phone.(GT-I9305 international version) or actually which one on this side there are many PDAs and CSCs forms.are these important? or ı can flash any of them?

try which one works best for you

Related

[Q] How to flash Galaxy mini with stock firmware?

I need help with flashing stock firmware. Well, I flashed my device with some turkish firmware who had 4 files and I did that via Odin. When I realised that I have turkish firmware I downloaded stock version which consists only 1 file and tried to flash my device trough Odin (followed procedure for flashing with one file) and it wont work. All I get is endless reboot loop on my device. What should I do? Please help!
bpodnar said:
I need help with flashing stock firmware. Well, I flashed my device with some turkish firmware who had 4 files and I did that via Odin. When I realised that I have turkish firmware I downloaded stock version which consists only 1 file and tried to flash my device trough Odin (followed procedure for flashing with one file) and it wont work. All I get is endless reboot loop on my device. What should I do? Please help!
Click to expand...
Click to collapse
Try again with wipe data/chace and wipe dalvik cache(from advance from in CWM)
Reflesh your stock firmware.
I high recommend you to rewrite stock 2.3.4 XXXXKPI(European)or specific for you region.
Anyway more details in this thread from Sammobile
KPI version have 4 files but was by far best version for me that i've used.
Also be carefull to load corect packs for boot/csc/modem/phone:
http://fulga.u-s.ro/fotos/android/incarcare_rom_in_Odin.png
If you are european shall not care if it is Turkish or Russian,just change leanguage.
I want to reflash my phone because KIES wont upgrade stock firmware after I flashed with Odin. It says that "this device cannot upgrade over KIES". It's common problem and I heard that people were solving that with reverting original stock firmware for their country. I dont know exactly am I right but I wanna try. Thanx!
Its very buddy, you can search it on this forum. You can find it here.

I9000 rom on i9001

Moin
I Have a easy Question....
Is it possible to flash an i9000 rom on the i9001
because i want flash darknight 2.1 rom with android 4.0.4
thank a lot for answers
Lump800
Do not do such things! ! ! Your phone may already be obsolete. I9000 and i9001 is a very different phones! ! !
Wysłane z mojego GT-I9001
Thank you kept me in front of a large error.
I had almost a door-stopper beautiful.
translated by google translator
sorry for that my english in not the best
Noo nooo and noooooooo. this is the fastest ticket to a broken phone
don't even think about it
is it possible to flash i9001 file to i9001 after i9000 firmware
it possible to flash i9001 file to i9001 after i9000 firmware. i had accidently flashed i9000 firmware on i9001 . now i want to flash it back to orginal firmware . is there anyway to rescue it
thanks a lot
darkeye said:
it possible to flash i9001 file to i9001 after i9000 firmware. i had accidently flashed i9000 firmware on i9001 . now i want to flash it back to orginal firmware . is there anyway to rescue it
thanks a lot
Click to expand...
Click to collapse
should be possible, you need to find the oldest possible stock rom and try flashing it with AiresVE.ops , MultiLoader Odin v.4.43
This happened to me, someone flashed cm for i9000 on i9001 and it worked for a while but it progressively started crashing, i took that phone and tried flashing stock but never could get pass setup connection in odin 4.43, tried all the variations (driver reinstall, new cable, remove battery, other PC etc) and in a hail marry attempt i managed to flash i9000 stock witch odin 1.83. Phone now works, enters download and recovery mode, but i still cant get past same error in odin 4.43 or flash custom recovery i any way (verification error from update method, adb flash just doesnt stick). ROM manager sees some custom recoveries but i cant enter them, my guess is because of different pit file from i9000.
Havent tried flashing i9001 rom with odin 1.83 because i cant use ariesve.obs from 4.43, i managed to connect to phone with heimdall and download pit, so that kind of connection works. My guess is that if i could somehow create pit file for this phone that works with heimdal i could flash proper stock rom, so im here to ask is it possible and how would i do it ?

Problem my phone is stuck on download mode.

I tried rooting with the chainfire auto root thing and after the red android screen i got the green one again and its stuck,i tried taking out the battery a few times but its still not working.
Any help would be amazing.
Well search would help ..
You say you are stuck on download mode .
As in download mode does screen not move unable to boot to recovery unable to power off .
Read the CFauto root instructions in full
JJEgan said:
Well search would help ..
You say you are stuck on download mode .
As in download mode does screen not move unable to boot to recovery unable to power off .
Read the CFauto root instructions in full
Click to expand...
Click to collapse
I did and didnt find anything helpfull for my situation.
Also tried to root again but again its stuck on downloading... do not turn off target screen.
Boot to download mode and it says as it should Downloading do not turn off .
You are now supposed to flash the firmware via odin .
You should flash your stock firmware to get the phone working .
Then read the basic faqs and guides before you flash anything as its pointless flashing without reading the basics .
Or take it to a service centre .
jje
Thanks for the reply ill consider doing that
but before i try that i managed to get into recovery mode does that mean i can try something or should i try the odin flash thing?
grpl said:
Thanks for the reply ill consider doing that
but before i try that i managed to get into recovery mode does that mean i can try something or should i try the odin flash thing?
Click to expand...
Click to collapse
Clear data and cache then reboot you may not have to reflash the rom. if that doesnt work tha use odin to flash stock rom. good luck
grpl said:
thanks for the reply ill consider doing that
but before i try that i managed to get into recovery mode does that mean i can try something or should i try the odin flash thing?
Click to expand...
Click to collapse
read the basics ignorance is no excuse .
ashraf sharif said:
Clear data and cache then reboot you may not have to reflash the rom. if that doesnt work tha use odin to flash stock rom. good luck
Click to expand...
Click to collapse
I did that and yeah i think i need to reflash too since that stuff didnt work.
i think i cant find my stock firmware from what i checked they dont have my country but maybe thats not importent
grpl said:
I did that and yeah i think i need to reflash too since that stuff didnt work.
i think i cant find my stock firmware from what i checked they dont have my country but maybe thats not importent
Click to expand...
Click to collapse
Is there a way to know my version/pda since i have no idea what stock rom to download
Device model no. in recovery mode
Hi,
Sorry to ask a random question. I Have my device model no. as S3 I9305 when I go to download mode and in my phone settings I can see my device model as S3 I9305T. I have recently installed Australian official firmware(XSA version without any career bloatware) in my phone, which is the S3 I9305T. I found it weird to have two different model nos. in 2 different places. When I first bought this phone it was the Telstra version, which is S3 I9305T. After that I changed many firmwares and installed S3 I9305 version from optus and other country's S3 I9305 version as well. Could you please tell me why is that?? Is this because I once installed I9305 firmware once? If that's the reason, today I flashed I9305T official firmware again with Odin. Is there any way to reset the download mode as well?? Please reply. Thanks.
grpl said:
Is there a way to know my version/pda since i have no idea what stock rom to download
Click to expand...
Click to collapse
Not unless you know what it is or saved the original .
You can just pick a stock rom for your area/ network .
If you bothered to read the basics their would be no need for all this ratting about .
@JJEgan I need some help, Ive got device, with same problem (i9305)
the donwload mode (which it defult boots into) does not show any device infos (which normally shows on the upper left corner)
Ive tried flashing latest stock rom (4.3) it gives an error (NOT "error pit file partition" but error flashing. failed it does not go beyond sboot )
any help? I am looking for 3 or 4 part firmware for this model, so that I could flash with pit.
dogmatism said:
@JJEgan I need some help, Ive got device, with same problem (i9305)
the donwload mode (which it defult boots into) does not show any device infos (which normally shows on the upper left corner)
Ive tried flashing latest stock rom (4.3) it gives an error (NOT "error pit file partition" but error flashing. failed it does not go beyond sboot )
any help? I am looking for 3 or 4 part firmware for this model, so that I could flash with pit.
Click to expand...
Click to collapse
So you run odin in windows.
Boot your phone to download mode
Connect device and wait for confirmation of connection in odin.
And then you click pda and choose a stock firmware.
And click start.
@tissot Odin gives fail error as I stated before. Am going to try 3 part odin package ive downloaded,.

[Q]Bootloop & No recovery Mode

Hello everyone ! I have a samsung galaxy s3 mini i8190
I flash CM , but i didn't like it so i tried to install with odin the original firmware.
Problem: Bootloop (logo Samsung Galaxy S3 Mini reboot infinite loop)
I can't enter in Recovery Mode, only i can enter in Download Mode
I use ODIN to try to install CWM , but still don't work..
And i have another problem. When I click start (in odin) it stops at SetupConnection, but if I disconnect & reconnect (usb) it starts flashing.
Please, help me.
Try to flash stock recovery instead of CWM.
tys0n said:
Try to flash stock recovery instead of CWM.
Click to expand...
Click to collapse
"I use ODIN to try to install CWM , but still don't work.."
I said this in the thread. If i'm wrong, please correct me.
Your kernel is f****ed up. You need to find any rooted stock kernel, flash it with Odin and then flash CWM. You don't need whole ROM, only kernel. Happened to me a lot while I was still on SGS1.
As for connection problem, perhaps clearing all drivers from your win and reinstall them could help.
Vladdyak47 said:
"I use ODIN to try to install CWM , but still don't work.."
I said this in the thread. If i'm wrong, please correct me.
Click to expand...
Click to collapse
Yes you did, but I asked you to try with STOCK RECOVERY instead.
It's not always a part of the official firmware package.
stenc55 said:
Your kernel is f****ed up. You need to find any rooted stock kernel, flash it with Odin and then flash CWM. You don't need whole ROM, only kernel. Happened to me a lot while I was still on SGS1.
As for connection problem, perhaps clearing all drivers from your win and reinstall them could help.
Click to expand...
Click to collapse
Can you help me with the link? Flash with PDA, right? (select PDA files, connect the device and click start)
Which one is good? http://forum.xda-developers.com/showthread.php?t=2187295
P.S. : I resolved the problem with connection
P.S.2: In Download Mode i have "CUSTOM BINARY DOWNLOAD: YES (3 counts) :|
P.S.3: When i try to flash a original firmware, after device restart it's an android charging something
EDIT: Now i have a new problem: FIRMWARE UPDRAGE ENCOUNTERED AN ISSUE. PLEASE SELECT RECOVERY MODE IN KIES & TRY AGAIN
Vladdyak47 said:
Can you help me with the link? Flash with PDA, right? (select PDA files, connect the device and click start)
Which one is good? http://forum.xda-developers.com/showthread.php?t=2187295
P.S. : I resolved the problem with connection
P.S.2: In Download Mode i have "CUSTOM BINARY DOWNLOAD: YES (3 counts) :|
P.S.3: When i try to flash a original firmware, after device restart it's an android charging something
EDIT: Now i have a new problem: FIRMWARE UPDRAGE ENCOUNTERED AN ISSUE. PLEASE SELECT RECOVERY MODE IN KIES & TRY AGAIN
Click to expand...
Click to collapse
Download service firmware and solve all your problems
Then just flash whatever rom you'd like.
Thanks a lot tys0n ! My Phone works now!
Mine has the same problem! I flashed kernels and params as well!
stenc55 said:
Your kernel is f****ed up. You need to find any rooted stock kernel, flash it with Odin and then flash CWM. You don't need whole ROM, only kernel. Happened to me a lot while I was still on SGS1.
As for connection problem, perhaps clearing all drivers from your win and reinstall them could help.
Click to expand...
Click to collapse
Solved !!! Thank you very very much, for all of u.. Worked ... Finally i can enter recovery mode and turn on my s3 mini.. . thanks XDA n really sorry for my english
stenc55 said:
Your kernel is f****ed up. You need to find any rooted stock kernel, flash it with Odin and then flash CWM. You don't need whole ROM, only kernel. Happened to me a lot while I was still on SGS1.
As for connection problem, perhaps clearing all drivers from your win and reinstall them could help.
Click to expand...
Click to collapse
What if my device cant be recognised by my pc. Ive tried every pc/laptop I own with different OS. So basically I have a bootloop stuck phone with no recovery mode available and it doesnt connect to the pc. Is there any way to fix that? Or is the phone completely bricked and I cant do anything about it.
PS: I have tried installing latest samsung drivers on my pc but it still cant recognise the phone.
Have had this phone for 6 years and it was ****ing amazing. I missed this little guy and want to fix him just as a "souvenir" since it was my first ever smartphone.

[Q] [Help] yellow triangle - cant enter download/recover mode

Hi all,
Yesterday I downgraded my Jellybean to Gingerbread firmware by using this tutorial: http://forum.xda-developers.com/showthread.php?t=2100642.
The downgrade was a succes, everything worked fine.
The final step of the tutorial siad: 'Note : You can flash Latest Update for your Country by Odin3 v3.07 ( Optional )'. So I searched for the stock firmware of my country and used Odin v3.07 to update. Now at this point the upgrade failed (NAND Write Start) and I get the 'yellow triangle' sign with the message: Firmware upgrade encountered an issue. Please select recovery mode in Kies & try again.
I can't get in download or recovery mode.
Odin still connects to my phone.
My question is how can I get my Android back to work :s
Thanks in advance,
Nebris said:
Hi all,
Yesterday I downgraded my Jellybean to Gingerbread firmware by using this tutorial: http://forum.xda-developers.com/showthread.php?t=2100642.
The downgrade was a succes, everything worked fine.
The final step of the tutorial siad: 'Note : You can flash Latest Update for your Country by Odin3 v3.07 ( Optional )'. So I searched for the stock firmware of my country and used Odin v3.07 to update. Now at this point the upgrade failed and I get the 'yellow triangle' sign with the message: Firmware upgrade encountered an issue. Please select recovery mode in Kies & try again.
I can't get in download or recovery mode.
Odin still connects to my phone.
My question is how can I get my Android back to work :s
Thanks in advance,
Click to expand...
Click to collapse
First, is your phone I9070 or I9070P? Second is that firmware for I9070 or for I9070P. If you missmatch you hardbricked phone...
shut_down said:
First, is your phone I9070 or I9070P? Second is that firmware for I9070 or for I9070P. If you missmatch you hardbricked phone...
Click to expand...
Click to collapse
2nd was: JW1_JV5_JVT.tar
I reasearched it,and I think it was for the GT-I9000, so I made a hard missmatch.
Is there a way so solve it? :s
Nebris said:
2nd was: JW1_JV5_JVT.tar
I reasearched it,and I think it was for the GT-I9000, so I made a hard missmatch.
Is there a way so solve it? :s
Click to expand...
Click to collapse
Your phone is probably hardbricked. Try to go to service centre.
shut_down said:
Your phone is probably hardbricked. Try to go to service centre.
Click to expand...
Click to collapse
Thanks for the support.
Brought it to the service center!

Categories

Resources