Database Develop

Flash sbf on 1.57

Is there a way to flash sbf on 1.57 cause I screwed my phone up pretty bad I had gibgerblur installed and then I installed gladiatrix over it and I'm having a lot of problems now
Sent from my Motorola Atrix using Tapatalk

milesjohnson said:
Is there a way to flash sbf on 1.57 cause I screwed my phone up pretty bad I had gibgerblur installed and then I installed gladiatrix over it and I'm having a lot of problems now
Sent from my Motorola Atrix using Tapatalk
Click to expand...
Click to collapse
Did you ever make a backup with CWM? If you did that would be the easiest to use to revert back. If not, then you can either flash this sbf (1.57) but you will not have root or anything mods, hacks, etc. Otherwise, you will have to go start over with flashing 1.26 sbf.

[SBF] Gingerbread - 4.5.91 AT&T USA Only [SBF]

Official Gingerbread SBF release for AT&T
Android 2.3.4 --- Blur_Version.4.5.91.MB860.ATT.en.US
1FF-olympus-user-2.3.4-4.5.91-110625-release-keys-signed-ATT-US-GAS_NA_OLPSGBATTSPE_P011.sbf.gz
http://www.filesonic.com/file/15073...signed-ATT-US-GAS_NA_OLPSGBATTSPE_P011.sbf.gz
WARNING : FLASH THIS SBF ONLY IF YOU ARE STILL RUNNING STOCK AT&T 2.2.2 WITH A LOCKED BOOTLOADER. ONCE YOU FLASH THIS ANY ATTEMPT AT A DOWNGRADE TO A PREVIOUS VERSION WILL BRICK YOUR PHONE.
If you are running anything else using this could increase your chances of bricking. Read the thread before flashing !!!!
This SBF is intended for people who don't want to deal with rooting and unlocking and OTA's and blur removal and fastboot and recovery and blah, blah blah I'm going to brick my phone regardless of what I do stuff.
It's also meant for people who have patience and want to upgrade safely who don't want to deal with Motorola Software Update because of the OS they're running.
It's an original SBF plain and simple.
Compression MD5 - 37D7E7D002B921F98D47BAD85DB55532
SBF MD5 - 56721D893E43B814E95683A00B165555

Read eval-s post below to clear up the confusion.
Would not use if you've unlocked with pudding. Will probably soft brick or worse.
Locked phones should be safe.
http://forum.xda-developers.com/showthread.php?t=1138204 (see post #2) for an unlocked version (with root).

I am complete noob in atrix,But i want to know that i have unlocked my atrix but if i flash New Firmware GB,Will it make my atrix again locked plz tell me.

is this the final version?

If i flash back to 1.8.3 will it be locked again? And update to official from there

I dont know about this sbf, but the service sbf i got from the motorola software update tool worked fine with the leaked ota (which is apparently the same as the official ota) and i was unlocked before i flashed it
edit: the compressed md5sum from the op is the same as the one i got from the motorola server which i flashed via rsd 5.3.1 with an unlocked bootloader. so apparently it is a sirvice sbf
edit: i also flashed zomgunlock-lite.sbf after i flashed the sbf

So is it safe to update if ur unlocked already...is this update unlockable? Im currently rooted and bl unlocked....
Sent from my MB860 using XDA App

rjayflo said:
So is it safe to update if ur unlocked already...is this update unlockable? Im currently rooted and bl unlocked....
Sent from my MB860 using XDA App
Click to expand...
Click to collapse
Read the second post, or try and post your brick results!

I also recommend not using. I used the 4.5.91 SBF a long time ago and bricked my phone shortly thereafter.

No, this .sbf is safe. It will just burn your fuse, just like the OTA, and make downgrading to anything impossible. To downgrade, you will have to use something that includes pudding, and you will have to 'oem unlock' ...that's all.
The .sbf is no more unsafe than the OTA. And once you've OTA'd, if you see "Failed to boot 4" this .sbf is the ONLY thing you can flash if you want to stay locked. Basically, if you have even started the OTA process, or have ever flashed this .sbf, you burned a fuse in ReservedOdm and have only two types of .sbfs you can flash. This one, or any+Pudding. Only this one will let you stay locked and still boot.
If you flash anything with Pudding after the OTA and you are still locked, you will see 0x1000. But it will be a soft-brick, and then your only choice will be to:
a) 'fastboot oem unlock' to continue.
or
b) flash this .sbf instead, and stay locked.
An AT&T user should never see 0x1000 from flashing this .sbf.
But afterwards, downgrades are dangerous. 'Official' AT&T 4.5.91 users will hard-brick their phones with 0x1000, stuck in nvflash mode, if they ever try to use any .sbf except this one, or the very special non-motorola version of 1.8.3 (found in the Pudding thread) or Pudding itself. In the later case, you can still escape the 0x1000 by unlocking. If you flashed stock 1.8.3 or below after running GB 4.5.91 officially, your phone is a paperweight. Be warned.
the2dcour said:
Would not use if you've unlocked with pudding. Will probably soft brick or worse.
Locked phones should be safe.
http://forum.xda-developers.com/showthread.php?t=1138204 (see post #2) for an unlocked-safe version (with root).
Click to expand...
Click to collapse

Does this flash a new radio too?
Sent from my Atrix

martyotaku said:
Does this flash a new radio too?
Sent from my Atrix
Click to expand...
Click to collapse
Yes, it does, but its the same radio that has been available for awhile now.
Baseband version
N_01_77_30P
Sent from my MB860 using XDA App

Does this official update has differences from the leaked?
Fixed bugs/better battery life, etc..
If it does, will somebody make a safe cwm zip to install it?
(for unlocked users)
Sent from my MB860 using XDA App

Paschalis said:
Does this official update has differences from the leaked?
Fixed bugs/better battery life, etc..
If it does, will somebody make a safe cwm zip to install it?
(for unlocked users)
Sent from my MB860 using XDA App
Click to expand...
Click to collapse
You already have 2.3.4 CWMs.

the2dcour said:
You already have 2.3.4 CWMs.
Click to expand...
Click to collapse
Yes, but these cwm`s were based on the leaked(beta?) att version.. Not on the official..
So I m asking, if the official(today's update) has improved battery life/performance etc?
Thanx!
Sent from my MB860 using XDA App

Paschalis said:
Yes, but these cwm`s were based on the leaked(beta?) att version.. Not on the official..
So I m asking, if the official(today's update) has improved battery life/performance etc?
Click to expand...
Click to collapse
As far as can be determined, the beta (from Moto dev servers) is the same as the "official" release now being pushed out.

so this include at&t stock GB kernel ( already posted by faux) and the well known .30P radio rigth?
Enviado desde mi MB860 usando XDA Premium App

eval- said:
The .sbf is no more unsafe than the OTA. And once you've OTA'd, if you see "Failed to boot 4" this .sbf is the ONLY thing you can flash if you want to stay locked. Basically, if you have even started the OTA process, or have ever flashed this .sbf, you burned a fuse in ReservedOdm and have only two .sbfs you can flash. This one, or 1.8.3+Pudding. Only this one will let you stay locked and still boot.
Click to expand...
Click to collapse
Eval, can you give us the path to cat eFuse status again and the comparison against which we can tell whether we've passed the point of no return with bootloaders? I would like to see where I'm at. Thanks.

So is this a service or full sbf for 4.5.91?

I am currently running locked and stock At&t 1.8.3. I want to update to this new OTA sbf. I read eval's post.
However, can someone confirm (break it down for me) that it is possible and probably safe to unlock the phone later using pudding or some other means. I am not an advanced user but will like to flash CM7 once its available.

Droid 3 on AT&T or T-Mobile

I just got my Verizion Droid 3 a few days ago. Still want to see if it could be used on AT&T or T-Mobile's Network. I understand that there is a band lock on it for US cellular carrier.
The question is: If I flash the XT883's chinese ROM. Will the phone get unlocked? (Since it comes with the radio.img).
I already unlock the phone from Verizon Wireless. Also, don't want get XT860, which is GSM only verion Droid 3. It is NOT a real global phone.
Update: Just flash the radio.img from Chinese ROM, no signal at all. Signature from verizion wireless needed?

Someone said if you flash the China Telecom ROM it will work. Maybe if we can extract the radio it will work better. Who knows?
Sent from my DROID3 using XDA App

XT883 Rom
http://forum.xda-developers.com/showthread.php?t=1249720

mvp3 said:
XT883 Rom
http://forum.xda-developers.com/showthread.php?t=1249720
Click to expand...
Click to collapse
Will this work!!??!??!

ericerk said:
Will this work!!??!??!
Click to expand...
Click to collapse
if your droid3 is unlocked,
you can flash this rom.

mvp3 said:
if your droid3 is unlocked,
you can flash this rom.
Click to expand...
Click to collapse
I'm gonna flash now (Yes i'm unlocked), but will it unlock it to us bands??
---------- Post added at 12:45 AM ---------- Previous post was at 12:15 AM ----------
I Couldn't flash it :/ maybe if this was incorporated into a us rom, like liberty

ericerk said:
I'm gonna flash now (Yes i'm unlocked), but will it unlock it to us bands??
---------- Post added at 12:45 AM ---------- Previous post was at 12:15 AM ----------
I Couldn't flash it :/ maybe if this was incorporated into a us rom, like liberty
Click to expand...
Click to collapse
yes,xt883 can't use safestrap,because xt883's preinstall only 512k

mvp3 said:
yes,xt883 can't use safestrap,because xt883's preinstall only 512k
Click to expand...
Click to collapse
What should i use to flash?

ericerk said:
What should i use to flash?
Click to expand...
Click to collapse
RSDLite5.5 or 5.6

mvp3 said:
RSDLite5.5 or 5.6
Click to expand...
Click to collapse
Didn't let me unzip it

ericerk said:
Didn't let me unzip it
Click to expand...
Click to collapse
what it means?

i flashed the xt883 rom to my xt862 droid 3 global n now im able to get GCI 850mhz GSM calling and texting here in alaska. battery doesnt last as long as the stock rom, other than that everything else works fine n all my apps still working

i couldnt unzip the file as in its compressed, i couldnt' uncompress

Unlocking GSM for use on T-Mobile...?
wrong place for post ><

which step you can not unzip

So any further news?

mvp3 said:
which step you can not unzip
Click to expand...
Click to collapse
i couldn't decompress to flash it with fastboot..

ericerk said:
i couldn't decompress to flash it with fastboot..
Click to expand...
Click to collapse
I can unzip,try download it again.
rsd lite can flash it,do not need fastboot if you use windows os.

All you have to do is flash the radio.img from SOLANA_SLNCT-57.1.60_Fastboot in fastboot mode
Code:
moto-fastboot flash radio radio.img
then add the following lines to the build.prop
Code:
persist.ril.rssi.enable.param6 = 1
persist.ril.baudrate=230400
I can confirm this works with an AT&T sim in an unlocked phone, tested with stock and liberty 2.0.

gfunkmonk said:
All you have to do is flash the radio.img from SOLANA_SLNCT-57.1.60_Fastboot in fastboot mode
Code:
moto-fastboot flash radio radio.img
then add the following lines to the build.prop
Code:
persist.ril.rssi.enable.param6 = 1
persist.ril.baudrate=230400
I can confirm this works with an AT&T sim in an unlocked phone, tested with stock and liberty 2.0.
Click to expand...
Click to collapse
Thank you,
If I want to use Verzion radio.img flash to XT883 rom,How should I do?

[HELP] How to root Milestone 3 xt860

IS there a way to root the XT860 With the Brazilian Retail 2.3.5 ROM ???
my xt860 got bricked and the only way that i found to get it back to life was install the fastboot brazilian rom and now i cant root it.. can you help?¿
i was thinking in install fastboot files from a Droid 3 XT862 and then root and install a custom rom for xt860..
what you think so?

Shavi said:
IS there a way to root the XT860 With the Brazilian Retail 2.3.5 ROM ???
my xt860 got bricked and the only way that i found to get it back to life was install the fastboot brazilian rom and now i cant root it.. can you help?¿
i was thinking in install fastboot files from a Droid 3 XT862 and then root and install a custom rom for xt860..
what you think so?
Click to expand...
Click to collapse
Find my thread called the xt860, custom roms and you. Has complete directions and links
Sent from my XT860 using xda premium

Moto X 2014 (XT1097 Canada) Wont Boot

Please help, my moto x 2014 wont boot what so ever. This first started from when I tried to root my XT1097 on android 5.1 using this: http://forum.xda-developers.com/mot...e-edition-superboot-style-root-motox-t2889264 not realizing it wasn't for android 5.1. Then it was acting weird so I booted into fastboot and used a factory image which was for AT&T devices. Realizing this was the wrong image (No service or wifi what so ever) I flashed the proper image to return to stock, but now my device simply sits at the M logo and wont boot. Any help to get this device back up and running is appreciated!

Kevin_Desousa said:
Please help, my moto x 2014 wont boot what so ever. This first started from when I tried to root my XT1097 on android 5.1 using this: http://forum.xda-developers.com/mot...e-edition-superboot-style-root-motox-t2889264 not realizing it wasn't for android 5.1. Then it was acting weird so I booted into fastboot and used a factory image which was for AT&T devices. Realizing this was the wrong image (No service or wifi what so ever) I flashed the proper image to return to stock, but now my device simply sits at the M logo and wont boot. Any help to get this device back up and running is appreciated!
Click to expand...
Click to collapse
Did you wipe data/factory reset when you reflashed your firmware?
Sent from my XT1095 using Tapatalk

xKroniK13x said:
Did you wipe data/factory reset when you reflashed your firmware?
Sent from my XT1095 using Tapatalk
Click to expand...
Click to collapse
Yep, I wiped them both as per usual. If it helps, I can still access fastboot and recovery.

If it is sticking at the M, its failing to boot Android at all. Does it roll into recovery automatically? Which firmware did you flash? Also, was the version flashed older than the one you previously had?
Sent from my XT1095 using Tapatalk

xKroniK13x said:
If it is sticking at the M, its failing to boot Android at all. Does it roll into recovery automatically? Which firmware did you flash? Also, was the version flashed older than the one you previously had?
Sent from my XT1095 using Tapatalk
Click to expand...
Click to collapse
It doesn't seem to roll into recovery automatically. I flashed this initially : VICTARA_ATT_5.0.2_LXE22.46-34 (AT&T zip), and then I flashed this one: RETCA_XT1097_5.0.1_LXE22.46-22. I forgot which version I had before I tried rooting, but I do know it was android 5.1.

Kevin_Desousa said:
It doesn't seem to roll into recovery automatically. I flashed this initially : VICTARA_ATT_5.0.2_LXE22.46-34 (AT&T zip), and then I flashed this one: RETCA_XT1097_5.0.1_LXE22.46-22
Click to expand...
Click to collapse
Is your bootloader unlocked? If you went to the 5.0.2 AT&T and your bootloader is locked, you won't be able to downgrade back to 5.0.1. Try getting a firmware that is the same version or newer.
Sent from my XT1095 using Tapatalk

xKroniK13x said:
Is your bootloader unlocked? If you went to the 5.0.2 AT&T and your bootloader is locked, you won't be able to downgrade back to 5.0.1. Try getting a firmware that is the same version or newer.
Sent from my XT1095 using Tapatalk
Click to expand...
Click to collapse
My bootloader is unlocked, and when I say that I'm stuck at the M, I mean I'm stuck at the bootloader warning. (I didn't know what to call it)

Kevin_Desousa said:
My bootloader is unlocked, and when I say that I'm stuck at the M, I mean I'm stuck at the bootloader warning. (I didn't know what to call it)
Click to expand...
Click to collapse
Yeah, that's where I figured it was hanging. All signs just point to a bad flash/firmware. I'd try downloading a different version (even 5.1 since you're unlocked) or verifying the hash on the firmware you flashed. You can use HashMyFiles to check the md5 or SHA hashes.
Sent from my XT1095 using Tapatalk

xKroniK13x said:
Yeah, that's where I figured it was hanging. All signs just point to a bad flash/firmware. I'd try downloading a different version (even 5.1 since you're unlocked) or verifying the hash on the firmware you flashed. You can use HashMyFiles to check the md5 or SHA hashes.
Sent from my XT1095 using Tapatalk
Click to expand...
Click to collapse
Would you know of a place where I can obtain the factory images then? The one I was using only had a couple of them, none of which were 5.1

Kevin_Desousa said:
Would you know of a place where I can obtain the factory images then? The one I was using only had a couple of them, none of which were 5.1
Click to expand...
Click to collapse
This thread has a link that has the 5.1 firmwares. You have to do some digging, but they should be there... http://forum.xda-developers.com/showthread.php?t=3148211
Sent from my XT1095 using Tapatalk

xKroniK13x said:
This thread has a link that has the 5.1 firmwares. You have to do some digging, but they should be there... http://forum.xda-developers.com/showthread.php?t=3148211
Sent from my XT1095 using Tapatalk
Click to expand...
Click to collapse
Sorry to be such a pain, but would you have flash instructions for the official firmware? I'm just afraid of messing something up

Kevin_Desousa said:
Sorry to be such a pain, but would you have flash instructions for the official firmware? I'm just afraid of messing something up [emoji14]
Click to expand...
Click to collapse
I am personally a huge fan of House of Moto, it will generate automatic scripts to flash the firmware for you. Check out the thread here: http://www.droidrzr.com/index.php?/topic/61124-House-of-Moto-[4.3]
Also, MotoFirmware has some firmwares for the X2, I used to use them for my RAZR M. http://motofirmware.center/files/category/46-moto-x-2nd-generation/
Sent from my XT1095 using Tapatalk

xKroniK13x said:
I am personally a huge fan of House of Moto, it will generate automatic scripts to flash the firmware for you. Check out the thread here: http://www.droidrzr.com/index.php?/topic/61124-House-of-Moto-[4.3]
Also, MotoFirmware has some firmwares for the X2, I used to use them for my RAZR M. http://motofirmware.center/files/category/46-moto-x-2nd-generation/
Sent from my XT1095 using Tapatalk
Click to expand...
Click to collapse
I tried to use the House of Moto with this firmware: http://motofirmware.center/files/file/249-victara_tmo_51_lpe2332-213_cid9_cfcxmlzip/ but when I load it into the HOM it displays this: "Custom recovery not found.
Using factory image: VICTARA_TMO_5.1_LPE23.32-21.3_cid9_CFC.xml.zip
ERROR: XML script not found in this factory image. This is not yet supported."

Kevin_Desousa said:
I tried to use the House of Moto with this firmware: http://motofirmware.center/files/file/249-victara_tmo_51_lpe2332-213_cid9_cfcxmlzip/ but when I load it into the HOM it displays this: "Custom recovery not found.
Using factory image: VICTARA_TMO_5.1_LPE23.32-21.3_cid9_CFC.xml.zip
ERROR: XML script not found in this factory image. This is not yet supported."
Click to expand...
Click to collapse
That firmware looks like the one for xt1095/T-Mobile/Pure Edition. Also, that error sounds like the HoM instructions weren't followed right. I've flashed my device a bunch with HoM.
Sent from my XT1095 using Tapatalk

xKroniK13x said:
That firmware looks like the one for xt1095/T-Mobile/Pure Edition. Also, that error sounds like the HoM instructions weren't followed right. I've flashed my device a bunch with HoM.
Sent from my XT1095 using Tapatalk
Click to expand...
Click to collapse
Would this one work: VICTARA_NIIBR_XT1097_5.1_LPE23.32-14.2_cid12_CFC.xml.zip? I'm just confused with the "NIIBR" in the firmware name.

Kevin_Desousa said:
Would this one work: VICTARA_NIIBR_XT1097_5.1_LPE23.32-14.2_cid12_CFC.xml.zip? I'm just confused with the "NIIBR" in the firmware name.
Click to expand...
Click to collapse
I'm not sure, to be honest.
Sent from my XT1095 using Tapatalk

xKroniK13x said:
I'm not sure, to be honest.
Sent from my XT1095 using Tapatalk
Click to expand...
Click to collapse
So the phone booted up, thank you so much for the help, but for some reason it wont detect my sim card, the wifi doesnt work on it, and it occasionally reboots. I also noticed that the baseband version is unknown. Is there a way to fix this?

Kevin_Desousa said:
So the phone booted up, thank you so much for the help, but for some reason it wont detect my sim card, the wifi doesnt work on it, and it occasionally reboots. I also noticed that the baseband version is unknown. Is there a way to fix this?
Click to expand...
Click to collapse
Sounds like whatever firmware you flashed had the wrong radios. You should be able to download the Canadian firmware and just flash the radios.
Sent from my XT1095 using Tapatalk

xKroniK13x said:
Sounds like whatever firmware you flashed had the wrong radios. You should be able to download the Canadian firmware and just flash the radios.
Sent from my XT1095 using Tapatalk
Click to expand...
Click to collapse
I did flash the Canadian firmware to my knowledge. RETCA_XT1097_5.0.1_LXE22.46-22_cid14_CFC.xml?

I was browsing the xda threads and saw this thread: http://forum.xda-developers.com/moto-x-2014/general/guide-xt1097-to-xt1095-nextel-t2972693 where it states: "IMPORTANT. From 5.1 update, the modems included on the update are FULLY compatible with all models, XT1097, 1092 and 1093 and all carriers ,so, you don't have to worry about losing IMEI, signal or data." So, should I be able to flash the brazilian xt1097 firmware and have the proper radios installed from this thread: http://forum.xda-developers.com/moto-x-2014/general/ota-android-marshmallow-6-0-final-t3248315 ?