My Problem: My Note will not boot. But I can put it into download mode. Then I try to flash a custom rom with PC Odin 1.85. Odin starts flashing but stucks after only perhaps 5% of flashing (factory...?).
What can I do? I tried different USB-Ports and different PC. Nothing helps. Ever the same problem!! Flash stucks after some seconds.
rogermiet said:
My Problem: My Note will not boot. But I can put it into download mode. Then I try to flash a custom rom with PC Odin 1.85. Odin starts flashing but stucks after only perhaps 5% of flashing (factory...?).
What can I do? I tried different USB-Ports and different PC. Nothing helps. Ever the same problem!! Flash stucks after some seconds.
Click to expand...
Click to collapse
Turn off firewall and antivirus. Make sure Kies is NOT running in the background. If you're having problems flash back to a stock GB rom and try again. Also give it some time. I have a very old PC and it took me 10 mins to flash.
Good luck!
I'll try it.
Edit: I tryed to flash kk9. Flash failed with error : can't open serial(com) port.
Gesendet von meinem Sensation mit Tapatalk 2
rogermiet said:
I'll try it.
Edit: I tryed to flash kk9. Flash failed with error : can't open serial(com) port.
Gesendet von meinem Sensation mit Tapatalk 2
Click to expand...
Click to collapse
Something could be wrong with your PC drivers.
It could also be that your firewall or antivirus is blocking the process.
- Make sure you have the proper drivers installed. Do that by either searching for the drivers on this forum or install Kies
- Put your phone in Download mode but don't hook it up to the pc yet
- On your pc open task manager and kill every process that has something to do with Kies or Samsung
- Start Odin
- Put all the files in the right sections
- Plug in your Note, preferably in a USB port you've not used with the Note
- Odin now should detect the Note
- Flash away
Now I tryed another USB Port. Started flashing kk9 and it went till "nand write start". Then it stucks there for more than 10 minutes.
Gesendet von meinem Sensation mit Tapatalk 2
Amy idea?
Gesendet von meinem Sensation mit Tapatalk 2
And flash from another computer ?
Try to flash
AbyssNotekernel42CWTouchOriginalLogo.tar
If it passes you can boot into CWM and flash a rom in your external SD. It worked for my SGN when it get stuck.
Will try this. Report later
Gesendet von meinem Sensation mit Tapatalk 2
Try starting Odin as administarator.
Then flash the new 4.0.3 official firmware and then flash Chainfire's kernel for it.
I had a similar problem.....no boot and only download mode was on...Stupid Note went dead between flashing on mobile odin....
This was the way I did it.
Best of luck to you !
When I'm fastbooting my T with the recovery.img from this thread: http://forum.xda-developers.com/showthread.php?t=1918966 it only says "waiting for device", I have conected my phone with the computer and have initiated the recovery mode (power on, volume up) and the light is blue/purple.
What's wrong? How can a flash over the CMW to my phone?
Thanks for all answers / B
Sounds like a driver issue within windows. My xda tells me I've no favourites saved (using the app) so can't post a link. But it's a quick fix, just need the usb drivers off the top of my head. I had a similar issue with my SXS
Sent from my LT30p
Hade tried to find The fastboot driver for Windows but i cant find it anywhere, would be everly grateful if someone could post a link to The driver!
Thx
Skickat från min LT30p via Tapatalk 2
Barracuda96 said:
Hade tried to find The fastboot driver for Windows but i cant find it anywhere, would be everly grateful if someone could post a link to The driver!
Thx
Skickat från min LT30p via Tapatalk 2
Click to expand...
Click to collapse
Download flashtool (Find a link in the first thread in the Q&A section) and then goto the driver folder and run the driver.exe there
Did you put the phone in the right USB dev mode. That was my mistake at first.
Hi all
I had to wipe my phone in custom recovery.
I wanted to flash it with RSD lite, as a lot of time, and i can't get it detected by my computer
I search to install drivers (wtf, they were on the computer..?!) and failed.
I gone to the configuration panel in my computer and uninstalled adb drivers
The i got "Fastboot smi S" drivers trying to install, failed too
I uninstalled moto drivers and reinstalled with the file Motorola_End_User_Driver_Installation_5.9.0_64bit.msi
rebooted
same problem...
i dont know how to make this fastboot mode detected again ....
Thx for help!
I had the same problem 2month ago with windows 8.
Instal sdk tools if you don't do that before or if it's always not working use an other computer because it's just a driver bug.
Sent from my XT890 using xda premium u
PELLET Nolwenn said:
I had the same problem 2month ago with windows 8.
Instal sdk tools if you don't do that before or if it's always not working use an other computer because it's just a driver bug.
Sent from my XT890 using xda premium u
Click to expand...
Click to collapse
hi
i tried to reinstall sdk, didnt worked.
i finally restored the computer to a prior date, like 3/4 days ago it was working, and i have been able to flash the rom with RSD
fabulous69 said:
hi
i tried to reinstall sdk, didnt worked.
i finally restored the computer to a prior date, like 3/4 days ago it was working, and i have been able to flash the rom with RSD
Click to expand...
Click to collapse
Just had the same kind of problem on Window 7 after playing with fastboot mode and various tools, this is how I solved it:
My XT890 in fastboot mode was recognized as "Unkown device"
=> I uninstalled the driver for this device.
My XT890 was thenidentified as "fastboot smi s" and would not install whatever I did
=> uninstalled "Motorola Device Manager" and "Motorola Mobile Drivers Installation 6.3.0"
=> reinstalled Motorola Device Manager (get it there : motorola-global-portal.custhelp.com/app/answers/detail/a_id/88481 , sorry new users cant post links)
then I plugged back my phone in fastboot mode and Windows correctly installed the drivers
dont have the phone anymore, but thx for sharing your experience, might be useful if anybody meets this problem again in the future.
have a nice week.
I think I bricked my device. not sure as i've never bricked anything before. it was rooted, and I had CWM and TWRP on it with a recovery. But it appears as though that doesn't matter lol. screen comes on and all that displays is the word Sony...and that just sits there forever. then if I connect a USB nothing happens.
Then when I dont turn it on, and connect a usb It connects but i haven't a clue if that will help at all as the device absolutely refuses to turn on when connected...Very sad day for me.
Tragediya said:
I think I bricked my device. not sure as i've never bricked anything before. it was rooted, and I had CWM and TWRP on it with a recovery. But it appears as though that doesn't matter lol. screen comes on and all that displays is the word Sony...and that just sits there forever. then if I connect a USB nothing happens.
Then when I dont turn it on, and connect a usb It connects but i haven't a clue if that will help at all as the device absolutely refuses to turn on when connected...Very sad day for me.
Click to expand...
Click to collapse
First grab flashtool from
http://www.flashtool.net/index.php
then get a stock ftf, connect your device in flashmode and flash the stock ftf
Gesendet von meinem C6603 mit Tapatalk
Do you used once flashtool?
Gesendet von meinem C6603 mit Tapatalk
Hi Guys,
I currently have an Hong kongese version of our beloved xz1 compact but unfortunately the updates are painfully slow and i would like to change firmware with the tools posted on this forum.
I would like to change into a German one which seems to be one of the very first to receive updates.
I have a concern and a pair of questions for ya'll :
1. If i change the firmware to a region that far and different from the one i have already, will i have different data signal and possibly lower or much lower?
I ask this because i previously had the X compact and i tried to do the same and my signal was no where as consistent and full as with the original Firmware.
2. Is there a way to change to another firmware but maintain the modem settings or files or whatever to have the same signal strenght of the original Firmware ?
thanks fellas and i apologise for mistakes since Eng isn't my native language. I come from Pizza Land
[OT] I'm sorry I can't answer your question, but I have to say that your written English is better than that of most of my fellow Americans!
You should be able to flash almost any firmware version, I don't think there are different modem drivers for each region any more. I have tried several regions of firmware here in the UK and none have effected signal reception or strength.
You will need ADB drivers for the phone and beware if you've used your laptop/workstation for another model of phone as sometime this can interfere.
Start with Xperiafirm and download the most recent firmware build, which as I type is UK customised.
Download newflasher and unpack it into the same folder as the firmware.
Delete userdataXXX.sin
Turn off phone, plug it in, start newflasher, type 'n' to the first two questions.
This should get you the latest build phone with your data intact
Didgesteve said:
You should be able to flash almost any firmware version, I don't think there are different modem drivers for each region any more. I have tried several regions of firmware here in the UK and none have effected signal reception or strength.
You will need ADB drivers for the phone and beware if you've used your laptop/workstation for another model of phone as sometime this can interfere.
Start with Xperiafirm and download the most recent firmware build, which as I type is UK customised.
Download newflasher and unpack it into the same folder as the firmware.
Delete userdataXXX.sin
Turn off phone, plug it in, start newflasher, type 'n' to the first two questions.
This should get you the latest build phone with your data intact
Click to expand...
Click to collapse
thank you very much!
I'll follow your instructions.
Sent from my G8441 using Tapatalk
From my past experience, the Customized NOBA region is usually among the first wave (if not the first) to receive new firmware. If you're betting on consistent bleeding edge updates, I'd go all in with NOBA.
unotretresette said:
thank you very much!
I'll follow your instructions.
Sent from my G8441 using Tapatalk
Click to expand...
Click to collapse
ADB drivers
Xperiafirm
Newflasher
Didgesteve said:
ADB drivers
Xperiafirm
Newflasher
Click to expand...
Click to collapse
This is the most complete answer I could ever receive.
Unfortunately , I have had another problem.
I downloaded the ADB Drivers but I can't install them.
When the phone is on (I activated USB debugging as well) I can get ADB to work on my Computer.
I run the CMD Shell and input "adb devices" and the smartphone is recognised automatically, however when I switch off the xz1c and press volume down and plug it to the PC to activate the "FLASH MODE", the phone isn't recognised at all.
I went to "Device Manager" and saw "Android" with a yellow exclamation point next to it so I clicked and selected Update Drivers.
I chose the folder where I unzipped the one you asked me to download and selected the subfolders.
Once proceeded, I got a negative response from Windows saying that" Windows could not find the drivers for your device".
So I am stuck here and I can't use newflasher at all.
Sent from my G8441 using Tapatalk
unotretresette said:
This is the most complete answer I could ever receive.
Unfortunately , I have had another problem.
I downloaded the ADB Drivers but I can't install them.
When the phone is on (I activated USB debugging as well) I can get ADB to work on my Computer.
I run the CMD Shell and input "adb devices" and the smartphone is recognised automatically, however when I switch off the xz1c and press volume down and plug it to the PC to activate the "FLASH MODE", the phone isn't recognised at all.
I went to "Device Manager" and saw "Android" with a yellow exclamation point next to it so I clicked and selected Update Drivers.
I chose the folder where I unzipped the one you asked me to download and selected the subfolders.
Once proceeded, I got a negative response from Windows saying that" no drivers have been found".
So I am stuck here and I can't use newflasher at all.
Sent from my G8441 using Tapatalk
Click to expand...
Click to collapse
You could download and install flashtool. Although you cannot use flashtool to flash your XZ1c, once it's installed there is a 'Drivers' folder in it, inside that is a very handy .exe that installs all the drivers you need for flashing and ADB.
Otherwise a quick search found this
Edit: I don't think you have to hold the volume down to use newflasher. All I did was turn the phone off, plug it in, start newflasher.
Didgesteve said:
You could download and install flashtool. Although you cannot use flashtool to flash your XZ1c, once it's installed there is a 'Drivers' folder in it, inside that is a very handy .exe that installs all the drivers you need for flashing and ADB.
Otherwise a quick search found this
Edit: I don't think you have to hold the volume down to use newflasher. All I did was turn the phone off, plug it in, start newflasher.
Click to expand...
Click to collapse
I am using Windows 10 64bit and I get this error from newflasher :
No usb device with vid:0x0fce pid:0xb00b
unotretresette said:
I am using Windows 10 64bit and I get this error from newflasher :
No usb device with vid:0x0fce pid:0xb00b
Click to expand...
Click to collapse
If you are using Windows 10 then the drivers won't have installed properly.
You need to hold 'shift' while restarting the machine. Then when it starts in safe mode, look for 'disable driver signatures' or something like that, in the advanced menu.
Then try installing the drivers again.
Didgesteve said:
If you are using Windows 10 then the drivers won't have installed properly.
You need to hold 'shift' while restarting the machine. Then when it starts in safe mode, look for 'disable driver signatures' or something like that, in the advanced menu.
Then try installing the drivers again.
Click to expand...
Click to collapse
I did it already and I have installed the drivers.
I see the same error ....
unotretresette said:
I did it already and I have installed the drivers.
I see the same error ....
Click to expand...
Click to collapse
If you open device manager on the PC and then open up USB devices, you should see the phone listed, with a warning.
Update the drivers in the USB section with the ones you downloaded from Sony, just point to the unpacked folder, you don't need to open any of the folders, it should work with the sa0117adb.inf file.
This is while your phone is turned off and connected, not turned on.
Didgesteve said:
If you open device manager on the PC and then open up USB devices, you should see the phone listed, with a warning.
Update the drivers in the USB section with the ones you downloaded from Sony, just point to the unpacked folder, you don't need to open any of the folders, it should work with the sa0117adb.inf file.
This is while your phone is turned off and connected, not turned on.
Click to expand...
Click to collapse
When I connect my phone in FLASH MODE and I check Devices Manager, I see "android" with the warning....
I try to select the drivers I downloaded but windows says that the drivers aren't found for this devices.....
I did everything possible !
unotretresette said:
When I connect my phone in FLASH MODE and I check Devices Manager, I see "android" with the warning....
I try to select the drivers I downloaded but windows says that the drivers aren't found for this devices.....
I did everything possible !
Click to expand...
Click to collapse
Did you install the drivers from flashtool drivers folder?
Edit: in safe mode..
Didgesteve said:
Did you install the drivers from flashtool drivers folder?
Edit: in safe mode..
Click to expand...
Click to collapse
I did but i get always the same errors:crying:
unotretresette said:
I did but i get always the same errors:crying:
Click to expand...
Click to collapse
when you started the flashtool drivers update, which drivers did you pick?
Didgesteve said:
when you started the flashtool drivers update, which drivers did you pick?
Click to expand...
Click to collapse
I installed flash mode and fastboot drivers.
Sent from my G8441 using Tapatalk
unotretresette said:
I installed flash mode and fastboot drivers.
Sent from my G8441 using Tapatalk
Click to expand...
Click to collapse
Perhaps this Reddit guide can help you
Didgesteve said:
Perhaps this Reddit guide can help you
Click to expand...
Click to collapse
I read the guide but these steps are exactly the ones I followed already.
I'm very unlucky.
Probably something I did in the past or my OS doesn't allow me to do what I wanna do.
I try the last option with my wife's laptop with Windows 7.
If it doesn't work, I'll wait for the update to come naturally which will probably take some months [emoji854]
Sent from my G8441 using Tapatalk
unotretresette said:
I read the guide but these steps are exactly the ones I followed already.
I'm very unlucky.
Probably something I did in the past or my OS doesn't allow me to do what I wanna do.
I try the last option with my wife's laptop with Windows 7.
If it doesn't work, I'll wait for the update to come naturally which will probably take some months [emoji854]
Sent from my G8441 using Tapatalk
Click to expand...
Click to collapse
Did you enable USB debug in the developer options?