Hello, now making my USB OTG cable from nothing. Saw in the "USB Host Controller" 's settings that I can change "Operation mode" to either "Host" or "Client", not only "OTG". Does this mean that my device can enable its host capabilities without connecting the "right" OTG cable with 4&5 pins connected?
Yes. OTG mode only means it will detect the operation mode automatically.
Redhattler said:
Hello, now making my USB OTG cable from nothing. Saw in the "USB Host Controller" 's settings that I can change "Operation mode" to either "Host" or "Client", not only "OTG". Does this mean that my device can enable its host capabilities without connecting the "right" OTG cable with 4&5 pins connected?
Click to expand...
Click to collapse
I made a few of these cables, OTG and audio line outs (fun with resistors had me soldering and making cables for a week lol)
USB Host Controller is just a helper app, You still need to short the pins for the cable to work, as well as making it a "powered" cable since the cappy wont power OTG compatible devices that need it.
Related
hi i was wondering if anyone out there new if there was an SDIO USB HOST card, similar to the shown on the link below (but obviously SD not CF)
http://www.ratocsystems.com/english/products/subpages/cfu1u.html
if not, does anyone know/have tried the above CF to USB Host with a standard usb webcam and got it to work? if so can you explain how i go about setting it up.
thanks
smigger666
i'd suspect that the fact that usb to host have to supply 5volt with 0.5mA
it could be an issue for something as thin as an sdcard
also not sure if the sdio interface even operate at 5v
usb host
I haven't seen an sdio to usb card, but I use my "htc universal" with it's mini usb as a usb 1.1 host. It works ok but you have to supply external power.
if you have that working you are the first and only person i know of who gotten any htc device act as usb host
sure there were rumors that it would do host
but later on ppl retracted those claims
After wiring up a cable for that, how do you set the phone to 'host mode'?
Thanks
usb host is not a mode
your pc is in host mode always
as are the 2 htc devices which do support
usb host out of the box
is a device is connected and the driver
is present the device works
Nope, USB host is a mode. It's the whole Master / Slave affair. Granted, it's automatic for most devices when another is connected... ah... that ought to answer my question I guess.
when looking at the storage control panel, it lists internal, sdcard-ext, and then "/mnt/usbdisk_1.1.1" and says "insert an [sic] USB disk for mounting".
so if i were to come up with some sort of adapter, could i plug a thumb drive into my phone's micro usb port to move files between the phone and the thumb drive? i can think of plenty of times that would be useful!
Tried. OTG cable works with Samsung galaxy S2 devices (Skyrocket using either SKY ICS or rooted OTA) but haven't got it to work on our Droids...(Bionic ICS leak, RAZR ICS OTA, Droid 4 ICS OTA...all rooted).
But if someone can prove me wrong I'd be happy to "eat my words" ...
Be strong and very Koragus, my ninja...
OTG works, BUT only in a very cumbersome way, since external power is needed.
A powered USB hub does not suffice, since it only powers the slave devices, not the host (= phone). The phone must be in charge-mode, which requires a Y-cable.
You need:
- an OTG adapter
- a USB hub with mini-USB in
- a USB Y cable with 2 normal USB plugs and one mini-USB out
Then
1. Connect the OTG adapter to your phone's micro-USB input
2. Connect the 'middle' USB plug of the USB Y cable into the OTG adapter
3. Connect the 'outer' USB plug of the USB Y cable to a charger (can be a portable battery as well)
4. Connect the mini-USB plug of the USB Y cable to the hub output
5. Connect any device you want to use to the USB hub
It looks like this (found this picture for Razr):
http://www.flickr.com/photos/teppan_hakushaku/6817735705/
Edit: I verified it for Droid 4 last week, but didn't take my own picture yet. Works with ICS .215 leak, no 3rd party apps (like 'StickMount') seem to be needed.
Edit2: According to some other posts in this forums (search for 'OTG') it will only work for FAT32 formatted drives. Didn't check this in detail but my drive was already FAT32. Also I found it did not work for my cheap wireless keyboard's USB dongle, but connecting a wired keyboard worked fine.
...reminded again why I love this community...
...no possible links to a purchase of this "y" cable?
Be strong and very Koragus, my ninja...
Glad I could help!
They come with some portable harddisks, so that's where I got mine. Not sure about the linking policy on XDA, please remove if not allowed. Here's an example:
http://www.dealextreme.com/p/usb-2-0-mini-5-pin-to-a-male-power-y-cable-62-cm-65630?item=10
Hi friends,
I want to attach to my touchpad memory card reader and external hard drive.
I wonder if it will be possible instead of buying Y cable and connect it to the OTG, to use my existing USB hub and connect to him the devices and the external battery bank.
Will it work?
Thanks
avizov2 said:
Hi friends,
I want to attach to my touchpad memory card reader and external hard drive.
I wonder if it will be possible instead of buying Y cable and connect it to the OTG, to use my existing USB hub and connect to him the devices and the external battery bank.
Will it work?
Thanks
Click to expand...
Click to collapse
im assuming youre talking about doing this in android 4.0.x +. if so then yes you should be able to connect an externally powered usb hub to the OTG cable and connect more than one device at a time.
Thanks
haxin said:
im assuming youre talking about doing this in android 4.0.x +. if so then yes you should be able to connect an externally powered usb hub to the OTG cable and connect more than one device at a time.
Click to expand...
Click to collapse
Yes android 4.
to be precise, I don't have powered usb hub.
I have normal usb hub which I will connect him the power with usb battery bank device.
will it work?
avizov2 said:
Yes android 4.
to be precise, I don't have powered usb hub.
I have normal usb hub which I will connect him the power with usb battery bank device.
will it work?
Click to expand...
Click to collapse
Yes. You need to give power to the periphal usb devices. I tried the same yesterday, without problems.
Hey all
I have a powered Belkin USB hub (this one: http://www.belkin.com/us/F4U040-Belkin/p/P-F4U040), coupled with an OTG cable which I know work together, as my Kindle Fire recognizes all USB devices through this setup (Keyboard, Mouse, Flash Drive etc).
I was surprised to find that my HP touchpad does not recognize any devices connected to this hub.
I did some diagnostics with USB Device Utility, and the touchpad recognizes my USB OTG cable, as it shows as a 'Qualcomm On-Chip EHCI Host Controller'.
The touchpad simply does not see anything plugged into the hub, be it a keyboard, mouse or flash drive.
Please help me here, guys!
What am I doing wrong?
Thanks
MainCourse said:
Hey all
I have a powered Belkin USB hub (this one: http://www.belkin.com/us/F4U040-Belkin/p/P-F4U040), coupled with an OTG cable which I know work together, as my Kindle Fire recognizes all USB devices through this setup (Keyboard, Mouse, Flash Drive etc).
I was surprised to find that my HP touchpad does not recognize any devices connected to this hub.
I did some diagnostics with USB Device Utility, and the touchpad recognizes my USB OTG cable, as it shows as a 'Qualcomm On-Chip EHCI Host Controller'.
The touchpad simply does not see anything plugged into the hub, be it a keyboard, mouse or flash drive.
Please help me here, guys!
What am I doing wrong?
Thanks
Click to expand...
Click to collapse
Are you sure that's powered? The picture doesn't show any DC connectors. Is it powered by something like a mini USB to USB cable on the back? If so, that might not be enough to power the device and the peripherals attached to the ports.
Belkin Hub
Daistaar said:
Are you sure that's powered? The picture doesn't show any DC connectors. Is it powered by something like a mini USB to USB cable on the back? If so, that might not be enough to power the device and the peripherals attached to the ports.
Click to expand...
Click to collapse
The belkin does have an external dc power supply and is not powered via usb
I think you need a Y cable even with a powered hub as its purpose is to inject power back into the OTG chip in the Touchpad.
SO I was this weekend to ski and when I came home I couldn't find my usb cable and charger...I have another mini usb cable but it just charging my phone mass storage not working...this is because is not an original usb cable right? Is there any tric or something to make it work?
ilooze said:
SO I was this weekend to ski and when I came home I couldn't find my usb cable and charger...I have another mini usb cable but it just charging my phone mass storage not working...this is because is not an original usb cable right? Is there any tric or something to make it work?
Click to expand...
Click to collapse
if it is charging.....then the pins for the data transfer in the mini-USB cable is not connected.....AFAIK, I think there are no tricks....
one trick is to get yourself a new data cable....
I'm trying to set up an Octoprint server on my old Note5 and as a result I need to be able to charge while using an OTG cable. I figured out that whenever I plug in a cable into the micro usb port, it disables wireless charging. Is there any way to override this?