Related
So I upgraded to the latest mr clean rom and did some tweaks with the registry Wizard. I was playing around with it for a while and turned it off to charge overnight. I wake up and try and turn it on and nothing. I've tried soft reset, and hard reset and it doesn't turn on or do anything. When I plug in my charger the light on my phone doesn't even come on. PLEASE HELP. WHAT CAN I DO!!!.
dew1989 said:
So I upgraded to the latest mr clean rom and did some tweaks with the registry Wizard. I was playing around with it for a while and turned it off to charge overnight. I wake up and try and turn it on and nothing. I've tried soft reset, and hard reset and it doesn't turn on or do anything. When I plug in my charger the light on my phone doesn't even come on. PLEASE HELP. WHAT CAN I DO!!!.
Click to expand...
Click to collapse
It seems that you bricked you phone mate. I think that you installed MrClean rom in a G4 phone so you irrimediably f*cked up the bootloader (IPL and SPL). Many users have reported that their phones were able to boot (and behaved normally) immediatly after the flashing but were dead after they turned them off for the first time, this is what happened to you.
Only thing you can try is going to bootloader mode (but i think it won't work since you messed the bootloader) and then flash a new rom. To do this, press and keep pressed both the keys on the right side and then insert a pin in the reset hole briefly. If the phone goes to the tri-colors screen then you're safe, if not continue reading.
If your warranty perior is not yet over then you can have a new phone for free (DON'T tell them that you flashed an experimental rom!!! Tell only that it went off suddenly or that you were installing an official rom!).
Service centre can repair your device (i suppose they've some method to reflash the bootloader) but i don't know how much they'll ask you.
Try asking other users on this forum. Sorry!
bye
...did you ry to recharge it with the ----ORIGINAL 1A CHARGER----? looks stupid, but i resuscitated mine just before throwing it in the bin. if it works, i will explain you the rest....
yup, I tried charging it with the home charger and still nothing. My battery reads at 3v and it's supposed to be 3.8 so it's not out of juice, but maybe it's just dead?
...you can try with just a normal 9 VDC battery, in order to boost up the voltage, to connect it for a few seconds to the ppc battery till you reach the 3.8 VDC and see if it's working...
Ok, i did that...and amazingly it turned on so I pluged it into the charger right away. Windows booted and about 20sec later the device turned off and won't charge again. So i tried again and the same thing happened. Do I need a new battery? TIA
dew1989 said:
Ok, i did that...and amazingly it turned on so I pluged it into the charger right away. Windows booted and about 20sec later the device turned off and won't charge again. So i tried again and the same thing happened. Do I need a new battery? TIA
Click to expand...
Click to collapse
This is waht you need:
http://www.thetravelinsider.info/phones/cellphonerecharger.htm
This charger is somehow wired weird... it charges the battery AND feeds juice to the phone at the same time (believe it or not, regular chargers and USB cables do not engage until the OS is loaded), allowing you to turn the phone on and in a few minutes plug it into the regular charger to continue charging. Just make sure you get the RAZR tip.
It has saved my ass more than once.
I fixed it , What I did was zap the battery with a 9v battery in 3 sec intervals, I did this about 5 times, then I pluged my phone into the charger and turned it on, the 9v gave it enough juice to boot up and the usb took over from there. So to everyone out there who is having this same problem, try this but don't over zap, check your battery with a multimeter.
im having the same problem----my MDA went dead last night because i forgot to charge the battery and then i went to plug it in the charger but the phone doesnt turn on no more...the light doesnt turn on like if it would be charging and i left it overnight and it still doesnt work..... do yall think that its the battery or is the phone just messed up and cant use it nomore????
Last time I had my battery completely drained, it wouldn't charge from laptop via USB. I read something about how the device's "smart-charging" function itself needs a bit of power to start-up...
but anyways, I couldn't charge the battery through the phone (software charging) - what I had to do was to take a USB cable, cut out one end, identify the +/- (red/black) wires, and charge them directly to the battery's two poles (metal plates). It took about 10-20 seconds of charging until I had enough power in the battery to place it back in the phone, start WM5 and charge it thru the phone.
It would have been much easier if you have a battery charger.
I had my phone connected to the computer through the usb cable, and I just left it connected for a week and it was completely dead and could not be turned on. I don't know how it drained the battery (probally by leaving the wifi on, but the computer was in use all the time). Anyway, thanks to this thread, I used the ac charger and it turned on.
Keywords: t-mobile tmobile mda phone won't don't turn on
phone down
thanks for infos
I'm going to give this a go; a Crossbow ROM flash went horribly wrong last night and in my attempts to repair it (I also must have flashed at least 9 times) the phone went dead. It won't charge either, but battery voltage is 3.7 volts, and I'm sat here wishing it was 3
Will get back to you all!
To update: no... it didn't work! I hooked the battery up to a computer power supply (nearest thing to hand) on 5v and 12v and the voltage increased to about 3.81V... I guess the battery is not the problem with my phone, though the symptoms were the same :-(
Any buttons I can press (i.e. like the voice command button for bootloader) to wake the damned thing up? It's probably fried.
Suggestion
CrArc said:
To update: no... it didn't work! I hooked the battery up to a computer power supply (nearest thing to hand) on 5v and 12v and the voltage increased to about 3.81V... I guess the battery is not the problem with my phone, though the symptoms were the same :-(
Any buttons I can press (i.e. like the voice command button for bootloader) to wake the damned thing up? It's probably fried.
Click to expand...
Click to collapse
My phone has a hardware problem with the on / off button (doesn´t work at all), at the beggining I thought it was a software problem and I tried all sort of tricks, then I gave up and recognized that was a hardware issue and I found 2 ways to turn the phone on 1) When is totally off (This happens when I have to remove the battery to change SIM card) I connect to the USB cable to my PC or to the car or wall charger and I make a soft reset. 2) When I see the phone signal led blinking I remove the memory card and wakes the phone up (not a good idea since I know that the card is going to get damaged sooner or later).
I just got a G3 wizard from a friend a couple days ago. On Thursday I upgraded it to XDA Mobile 6 and left it on the 2.25.11 (I think) T-Mobile Radio that the T-Mobile 2.26 firmware flash put on it. I used it all day on Friday and then I held the power button and shut the phone completely off for 25 hours, but left it plugged in to a usb to 110V AC adapter that came with my Dell Axim X50V. On Saturday night I went to turn it on and it would not come on no matter what I tried. I found this thread and checked the voltage on the battery directly with a multimeter, 3.13V. I cut the head off a usb cable and then held the black and red wires to the positive and negative terminals on the battery for 2 minutes with the head plugged into a front USB port on my PC. The multimeter then read 3.7V. I put it back into the MDA and it turned on, booted and informed me that the battery was completely drained. I plugged it into the USB to AC charger and it read 10% battery on BatteryStatus. I have left it to charge and it is currently at 60%.
I guess the lesson here is to not totally shut the phone off and let it sit, or the battery won't charge, even plugged into my charger. I guess the OS needs to be running in suspend mode for the charging circuit to run. I know I won't turn it all the way off ever again unless I have my little plug thing and my laptop with me.
(old) Nokia phones have a state called "Acting dead" (from service manuals) which takes place when phone is turned off and battery inserted. It means that the energy is flowing around the board so that the responsible hardware keeps waiting for a 'HIGH' signal ordering to turn ON the phone.
When batteries go bellow the 2.x volts they stop being charged by the phones. This is why i protect the battery terminals with tape when the phone is stored for some time and the reason why a lot of people thinks the phones are broken when not used for months. I usually use the 'freezer trick' where i leave the batteries inside the freezer all night and charge them next day.
just 2 cents...
My Wizard XDA got discharged over the weekend and wouldn't start up - after 12 hours on USB it still wouldn't start.
The charge tips saved my bacon - I modified a USB cable as per the instructions above, and used it to charge up the XDA battery - it only needed five seconds and the phone now boots!
Thanks All, great information!
My 2 cents...
If you're going to try the same, connect red usb to the +ve terminal of your battery and black USB to the -ve terminal of the battery. I'd suggest having a voltmeter to hand to check battery and supply voltage.
Disclaimer - the ablve worked for me, but I'm not responsible for anyone damaging themselves, their PC,their phone or anything else by using the above info!
BUMP! thought my phone was dead, hacked a USB cable and i'm back in business!!!!
TYTN II won't turn on
i left it plugged in all day and when i tried to turn it on it didn't respond. i have a second battery that was fully charged and that didn't work either. i tried a hard reset with it unplugged and with it plugged into the charger. nothing works. i'm on the standard at&t rom with lots of programs. i got it unlocked so i can't go to at&t.
Edit: thanks to this post, my problem has been solved. Thanks!
So last night I went from stock motorola 2.2 to this wonderful-seeming version of CyanogenMod on my UK milestone - the install went flawlessly, but now I have a problem - my battery is not charging at ALL.
While the phone was on last night after I charged it, it was plugged in, first to my PC and then to the wall socket. In both cases, the battery indicator had a ? (question mark) on it.
I thought it might have been some weirdness with battery calibration so I left it and plugged the phone in from the wall to charge overnight. This morning, my phone was telling me to connect my charger (despite it being plugged in) and on removing the power cable, it died due to no battery power left within 10 minutes.
While plugged in from the wall, the battery indicator comes up but again just contains a ? on it. The little white light next to the power socket never lights up.
If I plug the phone in to my PC via USB then if the handset is OFF, the white light comes on and around 10 mins later it gets enough juice to boot up. The problem is that when the CM7 software starts, the little white light disappears, the phone stops charging despite the cable being present, and it then dies 2 minutes later.
I know the battery is fine because it was perfectly fine before I installed CM7.
Anyone else experienced this problem and/or know how to fix it?
One thing I did manage to do before it died was install a battery calibration app that I found on xda-developers - this told me that the battery was running at 3267 mV - any idea if that's good or bad?
(and yes, I'm using precisely the same cable/charger I was using before I put this version of CM7 on, so I know they are fine - they charge a friend's SGS with no problems)
thatbloke83 said:
So last night I went from stock motorola 2.2 to this wonderful-seeming version of CyanogenMod on my UK milestone - the install went flawlessly, but now I have a problem - my battery is not charging at ALL.
While the phone was on last night after I charged it, it was plugged in, first to my PC and then to the wall socket. In both cases, the battery indicator had a ? (question mark) on it.
I thought it might have been some weirdness with battery calibration so I left it and plugged the phone in from the wall to charge overnight. This morning, my phone was telling me to connect my charger (despite it being plugged in) and on removing the power cable, it died due to no battery power left within 10 minutes.
While plugged in from the wall, the battery indicator comes up but again just contains a ? on it. The little white light next to the power socket never lights up.
If I plug the phone in to my PC via USB then if the handset is OFF, the white light comes on and around 10 mins later it gets enough juice to boot up. The problem is that when the CM7 software starts, the little white light disappears, the phone stops charging despite the cable being present, and it then dies 2 minutes later.
I know the battery is fine because it was perfectly fine before I installed CM7.
Anyone else experienced this problem and/or know how to fix it?
One thing I did manage to do before it died was install a battery calibration app that I found on xda-developers - this told me that the battery was running at 3267 mV - any idea if that's good or bad?
(and yes, I'm using precisely the same cable/charger I was using before I put this version of CM7 on, so I know they are fine - they charge a friend's SGS with no problems)
Click to expand...
Click to collapse
Try plugging the phone into the wall charger, without the battery. Try and boot it up and let it boot. Once it's booted up, give it a bit and try and put the battery in and leave it to charge.
What happens if you turn off you phone and plug it in a wall charger? If the problem isn't in your battery it will charge fully.
When you phone comes up, try to disable the 1% battery steps in settings. I got a problem with it, and after disabled/enabled it worked fine for me.
Hope this helps.
On plugging it into a wall charger, the phone comes up with its special battery charging screen (i.e. a fullscreen battery level indicator) - no amount of pressing the power button seems to get it to boot properly (with or without the battery).
I'll see if I can get in and get rid of the 1% steps thing later, thanks for the suggestion
afonsolage said:
What happens if you turn off you phone and plug it in a wall charger? If the problem isn't in your battery it will charge fully.
When you phone comes up, try to disable the 1% battery steps in settings. I got a problem with it, and after disabled/enabled it worked fine for me.
Hope this helps.
Click to expand...
Click to collapse
Dude, that was PERFECT.
Managed to get enough juice into the thing to get into the menu for a moment and was able to disable the 1% battery steps option - soon as I touch that tickbox, the battery indicator switches from a ? to the charging symbol and the phone starts charging. Thanks a million!
Nop dude, you are welcome
I'm using Darky ROM 10.4.2, My Galaxy S has been in use for almost a year now (i bought it second hand early last year), it has been running great up until this morning. I have always charged my phone while I sleep and everytime i'm next to the computer and have USB cable handy. I more than often charge directly from a computers USB or from a plug socket to USB converter i have (designed for phone charging).
Anyway what happened this morning was I woke up and my phone was really hot, and a message was on the screen saying that the battery is too hot or too cold and that charging has been paused.
I removed the battery and took it off charge and let the phone cool down. After rebooting, the phone seemed to be working fine, however when I tried charging via USB, I noticed that the phone recognizes that its charging (i.e. the charging animation icon comes up), however the percentage does not increase no matter how long i leave it charging (did it for about 30 minutes this morning). I thought this may have been a battery stats problem, so just to be safe I cleared the battery stats in CWM recovery. However the problem seems to remain. Although, I'm not sure whether its charging fully if i switch the phone off instead of booting it, as again it does recognize that its charging, but the battery meter in that case has no % and I can't actually make out whether its increasing or not.
Any ideas on what I need to do? Whether that's to buy a new battery, flash a new ROM, or anything else I could attempt?
(I'm aware a lot of battery problems are reported, but after searching I could not find one that particularly matches whats happening to mine.)
Hi, i have a big problem with my droid 4. I have tried plugging it into 2 different chargers, and it says its charging on the lock screen, but in the battery setting it says its discharging, even when plugged in. The droid also got HOT when it was connected to the charger for a while
What the heck could be wrong
are they moto chargers? could be battery, app
is phone rooted, romed?
Sent from my Clear using xda premium
sd_shadow said:
are they moto chargers? could be battery, app
is phone rooted, romed?
Sent from my Clear using xda premium
Click to expand...
Click to collapse
nevermind, it charges normally again after leaving it on the charger overnight. not sure what happened but im glad its fixed.
My daughter has the Droid 4, that is completely stock without root, and is having this problem right now. At first I thought the usb port was loose, and it was losing connection while charging. It says it's charging, but doesn't go above certain pecentages. It's all random each time it's plugged in. At first it wouldn't go above 5%, until I used the jumper method.
After I got it past 5%, I turned it on, let it charge by USB for a couple hours, and it wouldn't go past 20%. So I unplugged it, and let it go for a couple days without messing with it. I turned it back on, plugged it in, says it was at 5% again, and let it charge overnight. I got up the next day, it wouldn't even turn on, because it didn't charge at all, and discharged below 5%. Jumpered it again, this time for about 10 minutes, and got it to 60%. The battery never even got warm to the touch either time I jumpered it. I plugged it in today without turning it on, it goes to the phone off charging cylcle like it's supposed to, says it's still at 60%, but the charging animation doesn't show the battery filling up all the way, and then dropping back to 60%. The animation only goes about 5% further, and back to 60%.
This is her second Droid 4, and the first one did this too. I am hoping maybe it's something to do with the Stock ROM, and when JellyBean comes out, it will fix the issue.
The update finally came out for my daughter's Droid 4, and the update went smooth. I was able to keep it at 60% by only turning it on to check for the update. It dropped to 50% while updating.
Still having problems charging while on, or off. While on, it shows it's charging on the battery icon, and it also shows that it's charging in the battery status in settings. While off, it shows the battery charging animation as before. Once in a while it will take a bit of a charge, but not very much. I left it plugged in all night, and woke up to a completely dead phone that would not react to anything, because it's actually discharging while it says it's charging. I had to jumpstart it, let it go for 10 minutes, and it only took a 15% charge. Let it set for a while, and charged it again for a few hours, just to have it stay at 10% the whole time.
I removed everything that didn't come pre-installed, thinking maybe something was running in the background. That had no effect on it at all. Everything to do with data, wifi, and stuff that draws power has all been turned off. While off nothing should be drawing power, and it's still discharging while it says it's charging.
The chage port is a little loose, but the way I set it down the connection stays solid the whole time it's plugged in. I'm figuring something in the hardware is borked, or the battery is toast.
Any ideas anyone?
have you tried a different charger?
if so
i would do a factory reset
you may want to backup contacts, texts, call log… whatever data you want to keep
data on external sd card will be safe, but data on internal storage could get wiped
best to connect to a pc and copy everything on internal storage
pictures are in dcim/camera on internal &/or external sd card
more info on wiping data in my list
sd_shadow's [Collection] of Links for Droid 4
Sent from my Clear using xda premium
I have tried many chargers, and cables. Stock, Samsung, Duracell, and an old Motorola data/charge cable that needed an adapter. They were all doing the same thing.
I did a complete factory reset, and let it wipe all the internal data. It went back to 4.1.2, but it didn't fix the problem.
I messed with it some more afterwards, and threw the Motorola data/charge cable for my old RAZR V9X on it with the same results. Then I got to thinking, maybe it is a loose port, it's just getting enough contact to say it's charging, and not enough to actually charge the battery. I added some weight to the cable to keep constant, not too much, tension on the cable, and it started charging. Left it overnight, and it finally took a full charge.
Off to Cell Phone Repair Shop, it goes.
24fan4life said:
I have tried many chargers, and cables. Stock, Samsung, Duracell, and an old Motorola data/charge cable that needed an adapter. They were all doing the same thing.
I did a complete factory reset, and let it wipe all the internal data. It went back to 4.1.2, but it didn't fix the problem.
I messed with it some more afterwards, and threw the Motorola data/charge cable for my old RAZR V9X on it with the same results. Then I got to thinking, maybe it is a loose port, it's just getting enough contact to say it's charging, and not enough to actually charge the battery. I added some weight to the cable to keep constant, not too much, tension on the cable, and it started charging. Left it overnight, and it finally took a full charge.
Off to Cell Phone Repair Shop, it goes.
Click to expand...
Click to collapse
My Droid gets VERY VERY hot at times, my phone gets VERY slow and the same thing happens... it doesn't charge up (or takes absolutely forever to charge).
I have a widget called Battery Plus and you can see what uses the most battery and Google Plus is ALWAYS the culprit. I never use G+ (except to backup photos), but every time I go in and see what is using all my battery, its always G+. Its says taht G+ also downloads quite a bit of information onto my phone. Yesterday 10mb, today 2.5mb's or data. What is G+ doing??????
I have a Moto X 2013 that, after replacing the battery with a supposedly new, OEM battery, refuses to charge past 3%. This phone is rooted and was rom'd with the Nougat xPerience rom, but I tried flashing it with Nougat Lineage as a troubleshooting test.
I replaced the battery last night without incident, and the phone booted and seemed to behave fine, and the battery had about 30% charge. The only issue I found immediately after replacing the battery was a battery app installed on the phone saying the battery hasn't been charged for -19000 hours, or something a long those lines (I can't remember exactly what it said, as I did not install the app, my friend did who I was fixing the phone for. I just remember it was some outrageously large negative number.). Thought it was weird, and maybe thought it was a software issue, so I booted to TWRP and wiped the cache and dalvik. Rebooted the phone, and the app reset to something along the lines of 500 hours. That is a bit more believable.
I plugged the phone into my laptop to let it charge (as it was the only way I could charge it at the time), my laptop saw the Moto, and the Moto said "Charging..." and "Android Debugging...", and thought it was working. I had to run an errand, and when I returned about an hour later, the phone hadn't moved a drop up or down. My laptop was asleep, so I assumed maybe it just stopped charging when my laptop shut off, and I was exhausted myself so I just let it sit on standby all night.
Morning came, and the Moto is dead. I plug it into the wall charger I was just using to charge my v10 with (brand new cord, made for data transferring and charging that I used once before with the old battery), and head to class, hoping it'll charge. Guess what? It didn't charge. Well, it did a little. It went up from 0% to 3%, and sat there. Annoyed, I unplugged and replugged in the phone. It came up with the white battery charging screen, switched to the Nougat "N", vibrated, then went to a black battery charging thing. Once there, the battery icon went up two squares, the screen flashed, and the phone died and stopped charging, then repeated itself a few more times until it went silent.
I started to think maybe my brand new cord was screwing up, so I grabbed another one I had and plugged it into my desktop. I had read on another thread that sometimes you can force the phone to jumpstart charging by plugging in the phone and holding down power + volume down for upwards of two minutes. I tried this, and it charged enough that I could turn the phone on again, but it wouldn't charge enough to do much more. I left it plugged into my desktop for a few hours, not allowing the desktop to fall asleep, and yet the phone was still not rising above 3 or 4% despite the fact that it says that it is charging. Oh, and the phone was on the whole time if it was plugged in, but the moment I unplugged it (Like the one time it got over 5%), it immediately shuts down.
I know I'll probably just have to buy another new battery for the dumb thing, but I am just curious to see if there is anything I can do to fix this, just because I cannot currently afford to buy another new battery (and my friend, who this phone belongs to, is getting impatient on getting it back.)
Thanks for any help!
I have the same problem, charging topping out at 3% with a "new" battery.
Did you change the battery? Did it work?
Thanks for your feedback.
(FYI, this phone is running the stock lollipop firmware.)