Related
Hello
I had some trouble with a bricked SGS for about 3 weeks ago but got it on the run again with some flashing help.
Now i have this strange problem. If i turn it off or if it just goes black out, which it has begun to do after i flashed it, then it can't turn on, it just show the sun looking loading icon and then a empty battery icon and then turns off.
I can't load recovery mode with the combo, but i can make the download mode combo work.
But if i connect the phone with the charger/usb i recognize it and show that it charging up. Now it boot and shows the Galaxy I9000 model no. image.
Had tried flashing newer versions From XXJPO -> XXJPY -> XWJS3 and both with and without pre-partition and it still occur.
Now the question: Does any of you experienced people know this problem and can it be fixed somehow ?
Thank you in advance
First i would liik to charge phone for 24 hours and also check with another battery .
jje
JJEgan said:
First i would liik to charge phone for 24 hours and also check with another battery .
jje
Click to expand...
Click to collapse
The battery don't seem to be defected. Once the phone is booted with a cable connected, it goes without problems. It just will not boot without a charging signal.
Bump - Still actual
Try using Block 2 Odin method here to go back first to Eclair and if that works test phone then upgrade to Froyo .
jje
JJEgan said:
Try using Block 2 Odin method here to go back first to Eclair and if that works test phone then upgrade to Froyo .
jje
Click to expand...
Click to collapse
That happened to me a while back and I couldn't find a fix for it. Ended up doing the above and it resolved it.
Z3icon said:
Hello
I had some trouble with a bricked SGS for about 3 weeks ago but got it on the run again with some flashing help.
Now i have this strange problem. If i turn it off or if it just goes black out, which it has begun to do after i flashed it, then it can't turn on, it just show the sun looking loading icon and then a empty battery icon and then turns off.
I can't load recovery mode with the combo, but i can make the download mode combo work.
But if i connect the phone with the charger/usb i recognize it and show that it charging up. Now it boot and shows the Galaxy I9000 model no. image.
Had tried flashing newer versions From XXJPO -> XXJPY -> XWJS3 and both with and without pre-partition and it still occur.
Now the question: Does any of you experienced people know this problem and can it be fixed somehow ?
Thank you in advance
Click to expand...
Click to collapse
i agree wiv the suggetions frnds given.galaxy is hard to brick.i did all sort of unusual things an even uptodate lol.don worri m8 jus flash to older stock and hard reset.check the connectivity pins,to b clean even the battri pins.somtimes its best u format ur eternal xd on pc an format.and giving another hard rest makes things better.i had once formated my int sd on pc and the phone had emptied,then i flashed and things worked fine.personally sticking to stock rom is better if u dont wan troubles,cause every custom rom has som drawback an needs a lil knownledge to tweak it up.check kies if ur on it,i recomend download the recovery driver in it.hope u get some help.cheeeerzzzz
Same here...
Hello everyone,
I too have the same issue as stated in the first post.
I even had issue sometimes that when boot up.
The USB notification icon wouldnt turn off even if i wasn't connected.
Some threads suggested that I clean the USB port, which i did and nothing changed, even if it looked a little bit dirty in there (Hard to say since it is really small).
Now the USB port looks just as new but same issue: I cant power on the unit witout having it connected with a power cord.
Also, when offline in download mode, Odin detect the unit and I can flash my device (Which I did yesterday by flashing UGJH2 re-partition and UGJL2 not re-partition) but when boot up, I can't make it to sync up with the computer. No sync possible (Also now I'm not rooted anymore).
The unit is under warranty but since it is unlocked with a tool that needed rooting to lock back, abviously I would need to be rooted again but to do it, I need to be able to sync it with my PC (No cant do here).
I have some engineer at work that offered me to check it out for me, they think it is related with the USB port, but I'm worried about the warranty seal. I found how to disasemble it but does anybody knows where it could be located on the I9000M from bell (Vibrant)? Does it have one?
Anybody have any better suggestion or a second opinion, please?
Its my 3rd Galaxy S from Bell and Samsung is now the last company I would think when buying a new mobile.
EDIT: Did the Block 2 Method and now it doesnt even want to boot at all (Did the JPY_JPY_JPY.tar part), now it shows the loading sign even faster and the battery doesnt even show it self at all.
Hello again people!
Got my friend engineers to open the phone and they didnt find anything that would cause my issue (Also no warranty label...).
Does anybody knows how to root a Galaxy S with Froyo without a PC?
I want to return my phone to Bell Canada under warranty but my phone is unlocked and I want to lock it back before sending it back and I need to be rooted to do so...
Thanks for your help!
I got the same problem here. Could someone tell me more on this. What is this Block 2 ODIN method?
this problem can be caused by water or sweat that got inside the case of your sgs.
the biggest hole in the case is micro-usb port) i think condensation accumulated there and locked some contacts.
try to disassemble the phone and carefully clean and dry it.
this helped me.
HI,
I am from INDIA, few months back I got a Samsung Captivate , Till now i tried FIREFLY and CM7 ROMs . The first time flash i did it with ODIN i guess i did it with a wrong firmware ,So was stuck with AT&T screen boot loop issue. Searching the forums and found JIG may help and so made a JIG (as i can't get one here) . and recovered my phone and flashed stock and then FIREFLY and 2 weeks back i flashed CM7 for getting Gingerbread and not likeing the UI of the ROM tried to switch back to stock and then customize on my own.
So When i tried flashing Stock the installation was success the screen stuck few moments on AT&T logo and i thought it would go off, But as i was very eager to get my phone online again i pulled of the battery to restart manually (Which i dont think was nice idea ) Now the screen remains black even i use the JIG to get into download mode. But the phone heats UP when i plug it for charging on computer or directly to switch
HELP NEEDED as i am very addicted to this PHONE
I have the same issue. I was tryint to load Cognition and it just gets stuck on the ATT screen but I haven't tried a jig yet. I was wondering if I can replace the files on the phone with good files that aren't corrupted and see if it boots up because droid explorere can still pick up the phone and so does Odin but when I do a master reset nothing happens.
@rajasekhar - Have you tried: Removing all parts (battery, sim, sd) let it sit for a few min (my preference is around 10 min to insure no residual power is left in the system) then hold the jig in place and putting the battery back in? Keeping the jig in place, so that as soon as the device gets power it is immediately seeing the jig, before it can try any other processes.
A bit difficult to do with hand made jigs I know. If you still getting nothing then your in for the worst and the phone need a JTAG or service center visit.
Tho it sounds a little odd that it could boot up to seeing the AT&T logo, but does not respond to the jig. Might even be a hardware problem.
@i3oots - Since you say your still getting PC response your safe to try and reflash it or just pick something different altogether. Tho you might wanna let ODIN settle and just sit there doing nothing for a few min, w/o then w/ the phone plugged in. Or learn about Heimdall and go that route.
Would I be able to flash it even though it get's stuck on the ATT screen? It won't go into download mode. I'll look on the forums how to flash it too. I'm a newb at this which is why I bricked it but everyone has to start somewhere lol.
rajasekhar19489 said:
HI,
I am from INDIA, few months back I got a Samsung Captivate , Till now i tried FIREFLY and CM7 ROMs . The first time flash i did it with ODIN i guess i did it with a wrong firmware ,So was stuck with AT&T screen boot loop issue. Searching the forums and found JIG may help and so made a JIG (as i can't get one here) . and recovered my phone and flashed stock and then FIREFLY and 2 weeks back i flashed CM7 for getting Gingerbread and not likeing the UI of the ROM tried to switch back to stock and then customize on my own.
So When i tried flashing Stock the installation was success the screen stuck few moments on AT&T logo and i thought it would go off, But as i was very eager to get my phone online again i pulled of the battery to restart manually (Which i dont think was nice idea ) Now the screen remains black even i use the JIG to get into download mode. But the phone heats UP when i plug it for charging on computer or directly to switch
HELP NEEDED as i am very addicted to this PHONE
Click to expand...
Click to collapse
You have probably Hard Bricked your phone. A JIG will not work to recover the phone. If the phone has any life at all, then the JIG will work. Else, u hard bricked it...you should never remove the usb cable when flashing bootloaders or odin or anything!
the only solution is to get a JTAG which can recover hard bricks OR you can go to a warranty store (don't know about india) and make up a sob story and have them replace it..
rajasekhar19489 said:
HI,
I am from INDIA, few months back I got a Samsung Captivate , Till now i tried FIREFLY and CM7 ROMs . The first time flash i did it with ODIN i guess i did it with a wrong firmware ,So was stuck with AT&T screen boot loop issue. Searching the forums and found JIG may help and so made a JIG (as i can't get one here) . and recovered my phone and flashed stock and then FIREFLY and 2 weeks back i flashed CM7 for getting Gingerbread and not likeing the UI of the ROM tried to switch back to stock and then customize on my own.
So When i tried flashing Stock the installation was success the screen stuck few moments on AT&T logo and i thought it would go off, But as i was very eager to get my phone online again i pulled of the battery to restart manually (Which i dont think was nice idea ) Now the screen remains black even i use the JIG to get into download mode. But the phone heats UP when i plug it for charging on computer or directly to switch
HELP NEEDED as i am very addicted to this PHONE
Click to expand...
Click to collapse
Does your computer recognize the phone? If odin is open, does the box turn yellow when you connect your phone? Make sure you have the right drivers. I think cm7 and captivate drivers are different. Keep trying with the jig. Just because you can't see anything on the screen doesn't mean the phone is dead.
i3oots said:
Would I be able to flash it even though it get's stuck on the ATT screen? It won't go into download mode. I'll look on the forums how to flash it too. I'm a newb at this which is why I bricked it but everyone has to start somewhere lol.
Click to expand...
Click to collapse
If your phone is booting up far enough to send out USB info for ODIN and other PC programs to see it, then your still in a workable condition. This also means you can still get into download mode, but since things arn't working properly it will be harder. Depending on which bootloaders your phone has will direct which methods you'll have to try out to get into download mode.
AFTER you've had a chance to look around the forum and self-educate on the different ways of getting into download mode. If your still having problems give us a lil more info of what you were running before the flash and to which version of Cog you were trying to flash.
Did anything worked for you, if not only a jtag can help you looks like u hard bricked the phone.
Hi guys
@DaNarki : Yea i tried that method to .
Thanx for ur suggestions guys .I really squeezed through xda for all possible ways of unbricking but no use. SO thought JTAG was the only option.But wanna know more about JTAG???????
Went for a samsung service centre they said they wont handle other country products of samsung. Just yesterday went to the local Cell phone Repair store , He said like he would try using a Ctool box they have for installin onto the rom directly. So i thought why not Give a shot to it ...
That store guy raised another question in me . Yesterday after giving it in the morning he said to call in the evening . I did so and he said the Phone is booting on the Ctool but it is sometimes throwing error . I dint get his intention in saying so . have to go to him today
bricked maybe not
I thought I was bricked also ...HARD BRICKED......no buttons no nothing ...tried odin on, phone plugged in, and hold down volume up and down and reinstall batt......nothing worked.......but this... it worked for me........ok first of all remember this will be a bit tricky because you will have to keep the volume keys pressed the whole time till you have download mode......should also have full batt......take out the sim and any flash cards you may have in the phone and the batt.....set the phone down and watch a couple hours of tv or try to brick your buddies phone so he can feel your pain...lol something.....ok now after your tv show has gone off turn on your computer and start up odin one click to stock.... put just the batt in the phone.....if your friend is still there you should try this with 100% batt.... use his phone to charge your batt.....any way put the batt in the phone....plug the usb cable into your computer......now for the tricky part .......press down the volume up and down now and do not let them go till the end of this and you should have download mode.......now plug in the usb to your phone IF YOU HAPPEN TO GET DL MODE HERE THEN GO AHEAD AND LET GO OF THE VOLUME BUTTONS AND FLASH YOUR PHONE ....if not... KEEP THE BUTTONS PRESSED.......now take the batt out of the phone.....keep them pressed......unplug your usb cable......keep them pressed.... restart odin...... keep them pressed....plug your usb cable back in.......keep them pressed... re-install the batt.....you should get download mode.......remember you have to keep them pressed... JUST... the volume up and down pressed through the whole process nothing else....This worked for me and I was dead bricked no nothing from any of the keys no nothing..... I DIDNT INVENT THIS METHOD I READ IT ON HERE SOMEWHERE AND CANT FIND IT AGAIN......It did work for me when nothing else did.....so if the person that posted it reads this THANK YOU...... ................................................. I hate to say this but I may have got the last two instructions backward you may have to put the batt in before plugging in the usb cable.......Like I said I cant find the original post
rajasekhar19489 said:
Hi guys
@DaNarki : Yea i tried that method to .
Thanx for ur suggestions guys .I really squeezed through xda for all possible ways of unbricking but no use. SO thought JTAG was the only option.But wanna know more about JTAG???????
Went for a samsung service centre they said they wont handle other country products of samsung. Just yesterday went to the local Cell phone Repair store , He said like he would try using a Ctool box they have for installin onto the rom directly. So i thought why not Give a shot to it ...
That store guy raised another question in me . Yesterday after giving it in the morning he said to call in the evening . I did so and he said the Phone is booting on the Ctool but it is sometimes throwing error . I dint get his intention in saying so . have to go to him today
Click to expand...
Click to collapse
rajasekhar19489 said:
Thanx for ur suggestions guys .I really squeezed through xda for all possible ways of unbricking but no use. SO thought JTAG was the only option.But wanna know more about JTAG???????
Click to expand...
Click to collapse
If you just wanna know a bit about the process ask this guy. He is pretty much the only person in the US (I know not all to useful to a person in India) that does JTAG for the cappy.
I can tell you this much, it requires a special device called a Riff box and it sends boot info directly to the chip on the main/mother board that is used for the booting process.
Somewhere I've seen a site that listed info of ppl around the world that will JTAG, but I can't seem to find it right now.
malebornin69 said:
I thought I was bricked also ...HARD BRICKED......no buttons no nothing ...tried odin on, phone plugged in, and hold down volume up and down and reinstall batt......nothing worked.......but this... it worked for me........ok first of all remember this will be a bit tricky because you will have to keep the volume keys pressed the whole time till you have download mode......should also have full batt......take out the sim and any flash cards you may have in the phone and the batt.....set the phone down and watch a couple hours of tv or try to brick your buddies phone so he can feel your pain...lol something.....ok now after your tv show has gone off turn on your computer and start up odin one click to stock.... put just the batt in the phone.....if your friend is still there you should try this with 100% batt.... use his phone to charge your batt.....any way put the batt in the phone....plug the usb cable into your computer......now for the tricky part .......press down the volume up and down now and do not let them go till the end of this and you should have download mode.......now plug in the usb to your phone IF YOU HAPPEN TO GET DL MODE HERE THEN GO AHEAD AND LET GO OF THE VOLUME BUTTONS AND FLASH YOUR PHONE ....if not... KEEP THE BUTTONS PRESSED.......now take the batt out of the phone.....keep them pressed......unplug your usb cable......keep them pressed.... restart odin...... keep them pressed....plug your usb cable back in.......keep them pressed... re-install the batt.....you should get download mode.......remember you have to keep them pressed... JUST... the volume up and down pressed through the whole process nothing else....This worked for me and I was dead bricked no nothing from any of the keys no nothing..... I DIDNT INVENT THIS METHOD I READ IT ON HERE SOMEWHERE AND CANT FIND IT AGAIN......It did work for me when nothing else did.....so if the person that posted it reads this THANK YOU......
Click to expand...
Click to collapse
Thanx MAN!!!!!! . it seems interesting method to try .. but i have to wait 12 hrs to get my phone back from the guy i gave to repair that. he said his chances of getting it fixed are 50-50 so i might as well prepare for your method to ..
DaNaRkI said:
Somewhere I've seen a site that listed info of ppl around the world that will JTAG, but I can't seem to find it right now.
Click to expand...
Click to collapse
Thanx DaNaRkI .. hmm well i would now again start digging the threads for seeing wat u have suggested ..
rajasekhar19489 said:
HI,
I am from INDIA, few months back I got a Samsung Captivate , Till now i tried FIREFLY and CM7 ROMs . The first time flash i did it with ODIN i guess i did it with a wrong firmware ,So was stuck with AT&T screen boot loop issue. Searching the forums and found JIG may help and so made a JIG (as i can't get one here) . and recovered my phone and flashed stock and then FIREFLY and 2 weeks back i flashed CM7 for getting Gingerbread and not likeing the UI of the ROM tried to switch back to stock and then customize on my own.
So When i tried flashing Stock the installation was success the screen stuck few moments on AT&T logo and i thought it would go off, But as i was very eager to get my phone online again i pulled of the battery to restart manually (Which i dont think was nice idea ) Now the screen remains black even i use the JIG to get into download mode. But the phone heats UP when i plug it for charging on computer or directly to switch
HELP NEEDED as i am very addicted to this PHONE
Click to expand...
Click to collapse
hello brother,,
u can find the Jig here in india... i also purchased... and it worked for me..
Download-Mode-USB-Jig
press thanx if it helps..
rajasekhar19489 said:
Thanx MAN!!!!!! . it seems interesting method to try .. but i have to wait 12 hrs to get my phone back from the guy i gave to repair that. he said his chances of getting it fixed are 50-50 so i might as well prepare for your method to ..
Click to expand...
Click to collapse
Hope it helps I wish I could find the original post again to thank the guy that told me how to do it. I had sent that phone back to att and the promptly sent it back and told me the water dammage sticker in the bat compartment was missing and they wanted to charge me 409 bucks for the phone ....long story short it was there when I sent it and I told them to go pound sand up their ass because I wasnt paying them that much and ended up paying 125 bucks for a paper weight.So that is when I decided to have it jtaged but figured I would give it one more shot before mailing it off. That was when I found the post from that person and low and behold it worked........................... I hate to say this but I may have got the last two instructions backward you may have to put the batt in before plugging in the usb cable.......Like I said I cat find the original post
malebornin69 said:
Hope it helps
Click to expand...
Click to collapse
Buddy tried it ... Thanx for that..But dint help . Now going for another options i mean in search for other options
But ppl help me with JTAG thing and its users(or developers) availability in india
Forgot to mention
I Missed to explain my flashing procedure i have done this time . Like I never tried flash a boot file along and so was reading some threads about boot loader variations between FROYO and GINGERBREAD so i tried flashing ablong with boot loader and then I got the stock gingerbread file i put the boot loader SBL in heimdall Firstboot loader path .And Boom the first reboot got stuck and i removed the battery and then again when i tried to restart the phone is dead
Thinking this might have where the whole thing went wrong and made the cell dead .
Hi everybody, I searched everywhere for a solution but no luck
i love my note so much that if i couldnt fix it i think im gonna kill myself.
let me tell you the whole story, maybe you can revive my note again.
im a daily rom flasher, sometimes even 2 or 3 roms a day,
i wanted to flash ics stunner rom so i went into cwm recovery,flashed the zip file and wanted to format data\factory reset, but while the phone was formatting i accidently pressed the power button, the phone was stuck and didn't complete formatting, i took the battery out, put it back in and powered the phone, it was stuck at the bootscreen GTn7000 Galaxy Note.
I got into download mode and flashed a stock rom, but it was the same.
i downloaded and flashed other stock roms but it was stuck at the bootscreen.
then i wanted to flash a stock rom that came with a Pit file, i did everythig correctly, and Odin was stuck at the partition thing, for more than 15 minutes.
i unpluged the phone i pressed the power button, NOTHING!!
i officially bricked my phone which i worked so hard for months to get it.
i tried everything,even the jig thing, i couldn't buy so i had to make one.
maybe i did somethig wrong with the jig or maybe because i didnt solder it or the usb plug im using isnt working.
this may be relevant, i pluged the usb OTG in the phone and in the OTG was a bluetooth peice for computers, the piece had a light, and the light was ON.
Another thing that if i leave the battery in the phone for a while, the camera area in the back gets a little hot, my phone always did that meaning its still alive.
i may have written too much, forgive me but im really desperate.
Thanks in advance.
You probably end up going to Samsung. Pay €200 and get a new motherboard.
Good luck.
Sent from my CM9 GT-N7000 using XDA premium
hav0c said:
You probably end up going to Samsung. Pay €200 and get a new motherboard.
Good luck.
Sent from my CM9 GT-N7000 using XDA premium
Click to expand...
Click to collapse
WOW...
the problem is that i live in a fu**ed up country and we dont have samsung here.
all phones come without warranty and by smuggling from other countries
You mentioned killing yourself. Bro it's just a phone... Hang in there!!!
Sent from my GT-N7000 using Tapatalk 2
First thing donot flash Ics now untill you are craze about it.2nd donot use CWM as much as possible.Read this.
Ok to the problem now.Since you say it gets hot,it might be still alive.Remove the battery and insert it after 10 secs and insert the jig and after few secs press vol up button.Now connect the phone to computer and see if its detected if it does try flashing abyy's kernel.I dont know which kernel for sure.Somebody might help you.People were able to get into DL mode when there screen were not showing anything.
There are situations when your phone is working, but your screen is black.
Let's hope yours is one of those...Try this:
1. Don't flash Abyss. Download a stock GB Rom instead.
2. Charge your phone for a couple of hours. You need your battery for the
following steps.
3. After charging, take out your battery and wait 1 minute
4. Put it back in
5. Boot into Download mode (Volume Down+Home+Power) (you will see only black screen)
6. Count to 10
7. Press Volume Up
8. Count to 10
9. Start your PC Odin
10. Connect your phone to PC
11. Wait untill PC installs the necessary drivers
12. If all goes well, your PC Odin will flash the yellow light with COM info in it
13. Flash your stock GB Rom
If this doesn't work, you'll need to think of the ways of getting your phone JTagged or where to get a new motherboard.
Dude, if you have no way of repairing a bricked phone in your country then stay away from flashing custom ROMs!!!
Sent from my superior GT-N7000 using Tapatalk
Bro as u mentioned already that u flashed stock once...all root and cmw will be wiped... i would prefer going to samsung service center and tell them that u were updating your phone through kies and after the update completed ur phone stopped working... they will fix it for free... and act innocent
Edit::: dint see the other post where u mentioned that there is no samsung center at your place... in that case theres only one thing u can do... buy the motherboard and fix it urself.... sorry that ur beast is dead
izzmohamed said:
Hi everybody, I searched everywhere for a solution but no luck
i love my note so much that if i couldnt fix it i think im gonna kill myself.
let me tell you the whole story, maybe you can revive my note again.
im a daily rom flasher, sometimes even 2 or 3 roms a day,
i wanted to flash ics stunner rom so i went into cwm recovery,flashed the zip file and wanted to format data\factory reset, but while the phone was formatting i accidently pressed the power button, the phone was stuck and didn't complete formatting, i took the battery out, put it back in and powered the phone, it was stuck at the bootscreen GTn7000 Galaxy Note.
I got into download mode and flashed a stock rom, but it was the same.
i downloaded and flashed other stock roms but it was stuck at the bootscreen.
then i wanted to flash a stock rom that came with a Pit file, i did everythig correctly, and Odin was stuck at the partition thing, for more than 15 minutes.
i unpluged the phone i pressed the power button, NOTHING!!
i officially bricked my phone which i worked so hard for months to get it.
i tried everything,even the jig thing, i couldn't buy so i had to make one.
maybe i did somethig wrong with the jig or maybe because i didnt solder it or the usb plug im using isnt working.
this may be relevant, i pluged the usb OTG in the phone and in the OTG was a bluetooth peice for computers, the piece had a light, and the light was ON.
Another thing that if i leave the battery in the phone for a while, the camera area in the back gets a little hot, my phone always did that meaning its still alive.
i may have written too much, forgive me but im really desperate.
Thanks in advance.
Click to expand...
Click to collapse
Your phone is pretty much dead I'm afraid
Why didn't you bother to read stickies first?
It has been known for several weeks now that doing a wipe from CWM in a leaked recovery (I.e all ICS ROMs except cm9 official) will lead to a corrupted emmc drive ,thus a dead phone
And no ,you pressing the power button had nothing to do with it being stuck
The moment you hit wipe from ICS stunner's recovery your phone was dommed.
Anyway what's done is done ,now find an unofficial repair shop and replace your motherboard.
I hope this makes it clear ,and good luck to you.
izzmohamed said:
Hi everybody, I searched everywhere for a solution but no luck
Click to expand...
Click to collapse
Try this : http://forum.xda-developers.com/showthread.php?t=1257434
To force your phone into Download mode !
octavian90 said:
You mentioned killing yourself. Bro it's just a phone... Hang in there!!!
Sent from my GT-N7000 using Tapatalk 2
Click to expand...
Click to collapse
if you had gone through what i went through to get the phone, you would probably do the same.Thanks for the reply, any thing would help me right now.
vijai2011 said:
First thing donot flash Ics now untill you are craze about it.2nd donot use CWM as much as possible.Read this.
Ok to the problem now.Since you say it gets hot,it might be still alive.Remove the battery and insert it after 10 secs and insert the jig and after few secs press vol up button.Now connect the phone to computer and see if its detected if it does try flashing abyy's kernel.I dont know which kernel for sure.Somebody might help you.People were able to get into DL mode when there screen were not showing anything.
Click to expand...
Click to collapse
Thanks man, i will definitely try it right away.
mother board
mother board is gone due to kernel harm of ics leak
sorry
this is the fact...
chasmodo said:
There are situations when your phone is working, but your screen is black.
Let's hope yours is one of those...Try this:
1. Don't flash Abyss. Download a stock GB Rom instead.
2. Charge your phone for a couple of hours. You need your battery for the
following steps.
3. After charging, take out your battery and wait 1 minute
4. Put it back in
5. Boot into Download mode (Volume Down+Home+Power) (you will see only black screen)
6. Count to 10
7. Press Volume Up
8. Count to 10
9. Start your PC Odin
10. Connect your phone to PC
11. Wait untill PC installs the necessary drivers
12. If all goes well, your PC Odin will flash the yellow light with COM info in it
13. Flash your stock GB Rom
If this doesn't work, you'll need to think of the ways of getting your phone JTagged or where to get a new motherboard.
Click to expand...
Click to collapse
kvsandeepreddy said:
Bro as u mentioned already that u flashed stock once...all root and cmw will be wiped... i would prefer going to samsung service center and tell them that u were updating your phone through kies and after the update completed ur phone stopped working... they will fix it for free... and act innocent
Edit::: dint see the other post where u mentioned that there is no samsung center at your place... in that case theres only one thing u can do... buy the motherboard and fix it urself.... sorry that ur beast is dead
Click to expand...
Click to collapse
kvsandeepreddy said:
Bro as u mentioned already that u flashed stock once...all root and cmw will be wiped... i would prefer going to samsung service center and tell them that u were updating your phone through kies and after the update completed ur phone stopped working... they will fix it for free... and act innocent
Edit::: dint see the other post where u mentioned that there is no samsung center at your place... in that case theres only one thing u can do... buy the motherboard and fix it urself.... sorry that ur beast is dead
Click to expand...
Click to collapse
MR.change said:
Your phone is pretty much dead I'm afraid
Why didn't you bother to read stickies first?
It has been known for several weeks now that doing a wipe from CWM in a leaked recovery (I.e all ICS ROMs except cm9 official) will lead to a corrupted emmc drive ,thus a dead phone
And no ,you pressing the power button had nothing to do with it being stuck
The moment you hit wipe from ICS stunner's recovery your phone was dommed.
Anyway what's done is done ,now find an unofficial repair shop and replace your motherboard.
I hope this makes it clear ,and good luck to you.
Click to expand...
Click to collapse
pvillasuso said:
Try this : http://forum.xda-developers.com/showthread.php?t=1257434
To force your phone into Download mode !
Click to expand...
Click to collapse
You guys are awesome, im gonna do everything you said and get back with the results, fingers crossed.
I have a friend who's going to Dubai,UAE in a week or so. if nothing worked i'll send the phone with her to repair it at samsung,does anybody know if there's a samsung service center in Dubai and give me the location ?
i cant thank you enough,really appreciate all the help.
firasusman said:
mother board is gone due to kernel harm of ics leak
sorry
this is the fact...
Click to expand...
Click to collapse
OK, how much will it cost me ?
by the way i forgot to mention that before i bricked the note, it had a charging problem, saying voltage too high,charging stopped,and when the phone is turned off the battery icon keeps appearing and disapearing, could it be that the jig is not working because of that??
Try a different USB cable?
Sent from my SPH-D710 using XDA
izzmohamed said:
OK, how much will it cost me ?
by the way i forgot to mention that before i bricked the note, it had a charging problem, saying voltage too high,charging stopped,and when the phone is turned off the battery icon keeps appearing and disapearing, could it be that the jig is not working because of that??
Click to expand...
Click to collapse
You're not going to like this: I had to send my phone back to Samsung to get that fixed. Basically the charging port was shorting out, happens when stuff gets inside it (dirt, moisture, etc, from what I read). You could try cleaning it, but for me the port didn't break, it just acted like it was charging when there was nothing plugged in. So the JIG will work if it's supposed to.
jeffrey567 said:
Try a different USB cable?
Sent from my SPH-D710 using XDA
Click to expand...
Click to collapse
I did, still the same.
jayshah said:
You're not going to like this: I had to send my phone back to Samsung to get that fixed. Basically the charging port was shorting out, happens when stuff gets inside it (dirt, moisture, etc, from what I read). You could try cleaning it, but for me the port didn't break, it just acted like it was charging when there was nothing plugged in. So the JIG will work if it's supposed to.
Click to expand...
Click to collapse
Hmmm,i'll try cleaning it.I had the same situation, so the jig should work fine despite this problem ?
jayshah said:
You're not going to like this: I had to send my phone back to Samsung to get that fixed. Basically the charging port was shorting out, happens when stuff gets inside it (dirt, moisture, etc, from what I read). You could try cleaning it, but for me the port didn't break, it just acted like it was charging when there was nothing plugged in. So the JIG will work if it's supposed to.
Click to expand...
Click to collapse
Just out of curiosity: Are you in the US and had to send your international Note somewhere? I am wondering how one can get a support for an International Note if you're in the US.
I don't mind sending it to another country, but which Samsung center will accept it?
lanwarrior said:
Just out of curiosity: Are you in the US and had to send your international Note somewhere? I am wondering how one can get a support for an International Note if you're in the US.
I don't mind sending it to another country, but which Samsung center will accept it?
Click to expand...
Click to collapse
I am wondering the same thing, mine got bricked about a week ago and I don't really know what to do with it
Sad day today....all was well, tried to play around with Swap memory and then the trouble started,
First all the data on my SD card got wiped out !
After that the phone just went dead, no led when connected to charge,screen was dead no light, flicker of any sort, removed battery and tried many times still no luck...
suspected it could be a software problem so connected to to SUT, a phone was detected, tried completing the stock ROM reload, went to certain extent but then resulted in FAIL
Post that now I get a led red light when connected to charger but nothing else. does not go into download mode or battery charging animation.
Tried SUT once again but this time there is no phone detected.....
not sure if it is battery / handset problem....did the core areas in the phone get corrupted while playing with Swap ???
I partitioned using CWM, used Swapper2 app, all went well till I realised that data in SD was wiped clean.
Was on sharp mod...missing the phone badly...any help or guidance will be much appreciated...
Also will visit to service center help now that this phone is completely off SPICE stores ? yes it is still under "Warranty"
had to switch back to blackberry yucksss !!...for sometime I was infact trying to touch the screen
hoping to hear soon from you guys !!!!
First of all very sad to hear, My heartfelt condolences....
At this stage after trying SUT for multiple times, I think a visit to Spice service center is the only solution, please try it and update here
Be ready to part with your phone for a week atleast
BACK in BUSINESS
I got it Back folks.....thanks to SUT & Windows.....was breaking my head on what could be wrong...retraced back all my steps....
checked if the device has been wrongly configured by windows....went to device manager...lo I saw there was "Other Device" with something registered as Qualcomm CDMA. Deleted it...removed the usb and reconnected.....
Windows did a fresh installation of the device...after sometime I could see F drive of the device with image folder and all its contents....
Simply ran SUT once again, even now there was no display, just a gut feel everything will proceed smoothly....and yes SUT detected the device went through the installation. At one step it also asked if it could format F drive....I went ahead pressing OK....SUT finished successfully...after few anxious moments saw the familiar battery charging icon ......My day was made....and after few more anxious moments....I pressed power button to see SHARP Loading....my device is reborn again !
lesson learnt.....Don't play with SWAP mem, let the dev folks figure out and guide us...
If in any trouble keep SUT and preferrably Stock NB0 file handy.
Back in business folks !!
well done bro, was following your situation closely, so glad your phone is back to normal.
Sent from my SH8188U using xda premium
Glad that it works
Great job done
Sent from my Desire HD using xda premium
I will note your experience. Because I am a newbie who tend to do stupid things may be experiencing the same thing. Glad you can solved it and thanks for sharing.
Device still bricked
Hi, I have the same problem. My device (spice mi-410) suddenly stopped working. screen is blank, without power. It wont start in recovery or download mode. It wont charge. Only red led when connected to charger. That red led comes even when battery is not placed in the device and charger is connected. When i connect it to pc, windows detect it as HUAWEI Mobile Connect - Bus Enumerate Device in USB controllers. F disk is not visible nor can SUT detect it. Guess I am struck. This thing happened without me doing anything. It was working properly till night, just saw the device in the morning in this state. I had flashed official .nb0 few months back and the device was working flawlessly till now. Sending it to repairs to spice service centre is out of question (as it is out of warranty), nor those idiots know anything, they just gave me an estimate of INR 9k for repairs without seeing the device.
Any help appreciated.
9K OMG without looking at the phone
ya that idiot has fu***-up my phone earlier too. few months back my glass cracked, although the phone kept working fine. he changed the glass and returned the phone 2 months later, with all signs of ra**e been committed on phone. they never knew anything about the phone and were surprised to see such a huge device from spice. so they tried all there *tools* to pry it open before realizing that what damage they have done. my gps stopped working since then, they refused to fix it saying that as the phone has been *opened* (ra**d by them) it is out of warranty, although it was still under warranty.
And now this has happened.
Mod edit : dont use any abusive words its against the forum rules if u do need to use them i have edited ur post OK
forthe said:
Hi, I have the same problem. My device (spice mi-410) suddenly stopped working. screen is blank, without power. It wont start in recovery or download mode. It wont charge. Only red led when connected to charger. That red led comes even when battery is not placed in the device and charger is connected. When i connect it to pc, windows detect it as HUAWEI Mobile Connect - Bus Enumerate Device in USB controllers. F disk is not visible nor can SUT detect it. Guess I am struck. This thing happened without me doing anything. It was working properly till night, just saw the device in the morning in this state. I had flashed official .nb0 few months back and the device was working flawlessly till now. Sending it to repairs to spice service centre is out of question (as it is out of warranty), nor those idiots know anything, they just gave me an estimate of INR 9k for repairs without seeing the device.
Any help appreciated.
Click to expand...
Click to collapse
Hi Pretty similar to the problem I had, try and do the following
Try to use the newer SUT (1.8) version, search in this forum and you will get the link. If you are on it great.
Keep the nb0 file of any original rom - Spice GB on .32 kernel or Sharp GB on .35 kernel
connect the device with battery (hopefully charged well) to your computer, let windows detect it, launch your SUT, if you see a phone connected you are in luck !...just proceed with the next steps of by selecting the nb0 file, and selecting erase all user data.
SUT will prompt that your F disk is gone bad and do you need to reinstall it, select yes and let SUT do its stuff.
This will 100% load the ROM and F disk stuff and device will boot into the ROM once you finish.
In case SUT is not showing A phone is connected, restart your computer, ensure no other application is running, clear all earlier recognized devices in Device Manager and start fresh by connecting the device again.
vijayar said:
Hi Pretty similar to the problem I had, try and do the following
Try to use the newer SUT (1.8) version, search in this forum and you will get the link. If you are on it great.
Keep the nb0 file of any original rom - Spice GB on .32 kernel or Sharp GB on .35 kernel
connect the device with battery (hopefully charged well) to your computer, let windows detect it, launch your SUT, if you see a phone connected you are in luck !...just proceed with the next steps of by selecting the nb0 file, and selecting erase all user data.
SUT will prompt that your F disk is gone bad and do you need to reinstall it, select yes and let SUT do its stuff.
This will 100% load the ROM and F disk stuff and device will boot into the ROM once you finish.
In case SUT is not showing A phone is connected, restart your computer, ensure no other application is running, clear all earlier recognized devices in Device Manager and start fresh by connecting the device again.
Click to expand...
Click to collapse
hi
this is just my exp i had to use the old sutL3 which is the old 1.7.3
to flash the original India update of the 2.3 it did not work on the 1.8
this is based on my experience when i flashed back the orignal to sell the same and get the one V . I could be wrong do correct me if so but i did this just around 2 weeks back:laugh:
haree said:
hi
this is just my exp i had to use the old sutL3 which is the old 1.7.3
to flash the original India update of the 2.3 it did not work on the 1.8
this is based on my experience when i flashed back the orignal to sell the same and get the one V . I could be wrong do correct me if so but i did this just around 2 weeks back:laugh:
Click to expand...
Click to collapse
You could be right, if I recollect I infact flashed directly Sharp Stock ROM when I was facing the same problem. ....
btw how is HTC ONE V....you could have invested in a device with more RAM If I am not wrong this is with 512
vijayar said:
You could be right, if I recollect I infact flashed directly Sharp Stock ROM when I was facing the same problem. ....
btw how is HTC ONE V....you could have invested in a device with more RAM If I am not wrong this is with 512
Click to expand...
Click to collapse
hi
its ok budget buddy i didnt have much money and only the spice guy was giving me the buy back :laugh:
Phone not detected
I tried all the methods mentioned above on two different PC's. The Problem is that the phone is detected as "USB Input Device". The driver is provided by SUT. When it says device driver installed it shows as "usb input device" and the red notification LED glows. This happens whether or not battery is inserted. I charged the battery externally too.
Any Solutions?
Hello
Recently my device fails to reboot itself
I was with him in CM10. Then he began to have trouble running, absorption, and performance
Then I decided to lower it to CM 9 and solved at first, but then they grew and I could not format the device at all
What the device really shows me where this picture is off of the battery when I plug it into electricity.
Picture up and burns out until I physically take out the battery and has no access to electricity
Please note the battery is full and original.
I found a partial solution to insert the device via Odin and made burning GB version 2.3.5 with the PIT file. Full versions.
Although the device was. But I can not turn it off at all. Because if he turns off it returns to I said before you can not turn it at all and it displays the image with battery power connections.
What can you do?
Please help me! I have no idea how to solve the problem!
If u success in flashing stock 2.3.5 with ODIN without any failure and still become like that, only one problem: hardware failure.
compacity said:
If u success in flashing stock 2.3.5 with ODIN without any failure and still become like that, only one problem: hardware failure.
Click to expand...
Click to collapse
what i can do?
Is replacing the motherboard can handle the problem?
Are there other solutions?
if u can use da fone then juz dont turn it off, thats all. if u still wanna try to repair it urself, then see here
http://forum.xda-developers.com/showthread.php?t=1330491
but its quite hard to success n u need to hav at least basic on this one. Easy way, juz send it for repairing