So, I downloaded the nookie-froyo-0.6.8.custom.3.zip file mentioned in this thread:
http://forum.xda-developers.com/showthread.php?t=883175
I assume the next step is to make that zip file available to clockwork on the nook somehow? Is that correct? How do I do that?
Thanks.
custom.3 ? I see only nookie-froyo-flashable-0.6.8.zip on the op.
Anyway thats what I'm on and its what I finally decided on after a week of ROM jumping. It runs on the internal flash memory. emmc.
Two steps:
1)on your pc download a suitable CWM recovery .img file. Write it to your sd card via a sd card read/writer. I'm using the CWM 3.0.0.5 image. Next copy the above froyo image .zip to the sd card.
2)insert the sd card in your nook and boot from the power off state. It will boot off the SD card into CWR recovery. Use the recovery menu (vol+,vol-, nook n) and install the .zip file from the sd card. Next remove the sd card and reboot.
done.
I used the 4GB sdcard CWR .img file from here, can flash/backup/recover HC and froyo.
http://legacyschool.us.to/nookdev/clockwork/0.1-ext4/
britoso said:
custom.3 ? I see only nookie-froyo-flashable-0.6.8.zip on the op.
Anyway thats what I'm on and its what I finally decided on after a week of ROM jumping. It runs on the internal flash memory. emmc.
Two steps:
1)on your pc download a suitable CWM recovery .img file. Write it to your sd card via a sd card read/writer. I'm using the CWM 3.0.0.5 image. Next copy the above froyo image .zip to the sd card.
2)insert the sd card in your nook and boot from the power off state. It will boot off the SD card into CWR recovery. Use the recovery menu (vol+,vol-, nook n) and install the .zip file from the sd card. Next remove the sd card and reboot.
done.
I used the 4GB sdcard CWR .img file from here, can flash/backup/recover HC and froyo.
Click to expand...
Click to collapse
When I copy the froyo image to the card where do I place it?
Thanks!
Root directory
SO basically I want to
1.) burn a CWR SD card.
2.) Put it in the nook and boot into CWR
3.) Take the card out, format it back to fat32
4.) Put the Phiremod 6.3 SD flashable rom.zip on it.
5.) Pop it back into the nook and mount the storage.
6.) Flash Phiremod onto the SD card.
7- Turn nook on and Profit??
Well, I just booted my NC to CWR from SD, then removed the SD and was able to read a second card without any error from CWR.
So I suppose that would work in theory, the only difference would be you are doing it on one single card and not two. Though I don't know how safe it would be.
Yea I took the plunge and tried it.
Although I flashed
Update 4/30: v6.2 Update(This will format /system only): http://www.multiupload.com/58WUW1AZ0A
MD5 - 70b2ff0345897252f3f3dff8728a4b55
found in this thread Flashing Roms to SD CARD -
http://forum.xda-developers.com/showthread.php?t=998861
and I didn't boot into Phiremod, instead it was nook stock.
Would I first need to flash V6.zip, then flash the 6.2 update.zip?
EDIT* Did not work. Still boots into stock
How about you try this:
[ROM][CM7] Size-agnostic SD Card image and CM7 installer for SD Cards. with updater
I don't know if it works with a Phiremod ROM but it doesn't hurt to try. I used this to install plain CM7 on my Card.
____________________________________________________
Sent from NookColor CM7 using Tapatalk
So I'm trying to follow everything from here http://forum.xda-developers.com/showthread.php?p=38153094#post38153094 and I got lost at the part where I have to burn the image. When I burn it basically repartitioned my 8gig sd card down to 120mbs... What am I doing wrong? I don't know if I need to burn cwm first or if it's included there?
jmstrat said:
So I'm trying to follow everything from here http://forum.xda-developers.com/showthread.php?p=38153094#post38153094 and I got lost at the part where I have to burn the image. When I burn it basically repartitioned my 8gig sd card down to 120mbs... What am I doing wrong? I don't know if I need to burn cwm first or if it's included there?
Click to expand...
Click to collapse
That is what it is supposed to do, be 120 MB. And that 120Mb includes the CWM so you can flash the CM ROM. When you boot it in the nook, it further partitions it so that CM can be installed on the SD. Don't worry, the rest of your 8GB will be available.
Sent from my Nook HD+ running CM10 on Hybrid SD
Thanks!
leapinlar said:
That is what it is supposed to do, be 120 MB. And that 120Mb includes the CWM so you can flash the CM ROM. When you boot it in the nook, it further partitions it so that CM can be installed on the SD. Don't worry, the rest of your 8GB will be available.
Sent from my Nook HD+ running CM10 on Hybrid SD
Click to expand...
Click to collapse
Ok, the problem I had was that I was confused regarding where to put the rest of the files, apperantly I'm and idiot and didn't realize I'm supposed to put them in the internal memory... Ok let's see how it goes, thanks!
jmstrat said:
Thanks but how am I supposed to copy the cm10 zip file and gapps/converter file if they wont fit onto it? Also do I just insert the sd card in and then it automatically reformats it and then I'm supposed to plug it back into my pc drag the cm10 files and then put it back into the nook again? Forgive my ignorance I really want to try this out though! I also forgot to mention that I haven't done anything with my nook, it's non rooted and then only thing I've done is sideloaded the playstore on there, that's it. My nook is completely stock.
Click to expand...
Click to collapse
I'm not sure you read my instructions. I said to put the CM zip, gapps zip and converter zip on the internal media SD built into the nook, not on the external SD inserted into your PC. So it does not matter if the SD is only 120 MB, you are copying nothing there. Just download the zips with stock to internal SD or hook your cable to the PC with stock booted and copy to internal SD.
EDIT: I just edited the OP to clarify all this.
Sent from my Nook HD running CM10.1 on Hybrid SD
You weren't supposed to see that message lol..
leapinlar said:
I'm not sure you read my instructions. I said to put the CM zip, gapps zip and converter zip on the internal media SD built into the nook, not on the external SD inserted into your PC. So it does not matter if the SD is only 120 MB, you are copying nothing there. Just download the zips with stock to internal SD or hook your cable to the PC with stock booted and copy to internal SD.
Sent from my Nook HD running CM10.1 on Hybrid SD
Click to expand...
Click to collapse
Oh no I figured it out!!! I thought I deleted that comment I didnt want to embarrass myself.. I have another question, I'm using an 8gig card, but I want to get a 64gib card, what should I do when I get the new card, reburn and do the same steps? Thank you for replying to my question so quickly you're ****ing awesome! Wow I'm just messing around with cm10, it's like a new tablet, holy ****. Sketchbook pro appears to have less latency, finally I can draw! So what else is possible with cm10 now, what do you like about cm10 that wasn't possible before? Also what build prop is the tablet being seen as now?
jmstrat said:
I have another question, I'm using an 8gig card, but I want to get a 64gib card, what should I do when I get the new card, reburn and do the same steps?
Also what build prop is the tablet being seen as now?
Click to expand...
Click to collapse
If you want to move to a larger card, use win32diskimager to read the 8GB card to a file. The file will be 8GB. Then use win32diskimager to write that file to your new 64GB card. Then use partitioning software like Mini-Tool Partition Wizard to expand the last partition to the full size of the card.
The build prop is set as a B&N Nook HD.
Sent from my Nook HD+ running CM10 on Hybrid SD
I have Leapinlar's SD card image installed on a SD card that I used to then install the EMMC version onto my HD+ which is working great, thanks to Leapinlar and Verygreen for that. Since I don't want to misplace the SD card I've left it in my Nook, but then whenever I reboot it, it boots off of the SD card and goes into the CWM on the card. I was wondering if anyone knew of a way to activate the Cyanoboot menu on the card so that I could choose to boot from the card, or the EMMC, and possibly change the default so that it boots to the EMMC instead. I realize that this might not be the right forum as it isn't necessarily a Nook question, so thanks for any help.
Edit: I should specify that I used the 4GB CWM SD card image in Leapinlar's thread, and is the one I'd like to modify. Thanks.
Ask and Ye shall receive.
Attached below is a .rar file that has four files in it. Extract those files to the boot partition of your CWM SD, replacing any duplicates. It will add the cyanoboot menu to it. It will by default boot to CWM, but if you want to boot to emmc (stock or CM10.1 on emmc), hold the n key and the cyanoboot menu will come up and you can choose stock. If you want it to boot to emmc by default, just change the Default Boot Device from "CM10/10.1" to "Stock". Then it will boot to emmc if you do nothing. Then you can boot to CWM by using the cyanoboot menu.
You rock, thanks!
leapinlar said:
Ask and Ye shall receive.
Attached below is a .rar file that has four files in it. Extract those files to the boot partition of your CWM SD, replacing any duplicates. It will add the cyanoboot menu to it. It will by default boot to CWM, but if you want to boot to emmc (stock or CM10.1 on emmc), hold the n key and the cyanoboot menu will come up and you can choose stock. If you want it to boot to emmc by default, just change the Default Boot Device from "CM10/10.1" to "Stock". Then it will boot to emmc if you do nothing. Then you can boot to CWM by using the cyanoboot menu.
Click to expand...
Click to collapse
I know this thread is a bit old, but thanks! Didn't know if it would work,, but added it to my CM 10.2 SD so I could dual boot that and CarbonRom. Other than the menu having the wrong text, it works quite well.
Sent from my BN NookHD+ using Tapatalk 4
I have the Stock BN rom on DS card and have 10.2 on native install.. but an i think as far as installing the dual boot menu i got that right..
but when i try to switch to the Stock BN rom living on the SD card it just says loading SD... but never continues to the BN boot animation.. or loads continues to login... it feels like a boot loop... do i have to have root access to get this to operate... i have 10.2 root but BN SD is not rooted... confused...
i would just like a boot menu to allow the option to boot to the BN SD card or default to native 10.2..
help?
scuzzo said:
Im trying to put the Stock BN rom on DS card and have 10.2 on native install.. but an i think as far as installing the dual boot menu i got that right..
but when i try to switch to the Stock BN rom living on the SD card it just says loading SD... but never continues to the BN boot animation.. or loads continues to login... it feels like a boot loop... do i have to have root access to get this to operate... i have 10.2 root but BN SD is not rooted... confused...
help?
Click to expand...
Click to collapse
My files do not work with the systems reversed. Stock must be emmc and CM on SD. Sorry.
Sent from my Galaxy Tab 2 using XDA Premium
leapinlar said:
My files do not work with the systems reversed. Stock must be emmc and CM on SD. Sorry.
Sent from my Galaxy Tab 2 using XDA Premium
Click to expand...
Click to collapse
Right thread this time! So this is dual boot thread (sorry about earlier Leapin!).
Took me about five minutes to get where I'd made my mistakes though even after finding this and trying again. Now that I understand how this installs, and that stock must be in emmc, I just have one question....do I place CM 10.1 on the root of my SD card as a zipped, or unzipped, file for it to load from the menu? Or is there still more to do other than just "sticking the file on there?"
I know this much...every day I have greater & greater respect for xda developers. To be willing to explain things so even myself can understand it a little - and put up w questions - has to be a chore in and of itself. Thank you!
Prof24 said:
Right thread this time! So this is dual boot thread (sorry about earlier Leapin!).
Took me about five minutes to get where I'd made my mistakes though even after finding this and trying again. Now that I understand how this installs, and that stock must be in emmc, I just have one question....do I place CM 10.1 on the root of my SD card as a zipped, or unzipped, file for it to load from the menu? Or is there still more to do other than just "sticking the file on there?"
I know this much...every day I have greater & greater respect for xda developers. To be willing to explain things so even myself can understand it a little - and put up w questions - has to be a chore in and of itself. Thank you!
Click to expand...
Click to collapse
First you need to go to verygreen's SD thread and make the early 7.1 CWM card. The put the CM10.1 zip on internal memory using stock. Then boot with the CWM SD you just made and after it finishes preparing the SD, install the zip from internal memory. Then you can use the files in this thread to put the cyanoboot menu on that SD.
Sent from my Galaxy Tab 2 using XDA Premium
leapinlar said:
First you need to go to verygreen's SD thread and make the early 7.1 CWM card. The put the CM10.1 zip on internal memory using stock. Then boot with the CWM SD you just made and after it finishes preparing the SD, install the zip from internal memory. Then you can use the files in this thread to put the cyanoboot menu on that SD.
Sent from my Galaxy Tab 2 using XDA Premium
Click to expand...
Click to collapse
Ok, I seem to be / was good until I got to installing zip from internal memory. This is what has happened so far.
1. Created 7.1 CWM SD with win32 disc imager ...No probs
2. Not enough room on external card to place CM 10.1 zip file even though I started with 16 Gb....so I assumed you meant load CM 10.1 to Nook HD+ internal memory from my PC...no problem there.
3. This is where I got stuck: 7.1 card booted up just fine, but then I wasn't quite sure what next step was...found "install zip from internal SD" and tried that, but of course it sent the update - apparently - to emmc, as Cyanogenmod spinner logo now comes up after reboot.
So my question is how do I need to go about installing from internal memory once CWM 7.10 is running. Is there an adb command I'l need, or did I just choose wrong option?
Prof24 said:
3. This is where I got stuck: 7.1 card booted up just fine, but then I wasn't quite sure what next step was...found "install zip from internal SD" and tried that, but of course it sent the update - apparently - to emmc, as Cyanogenmod spinner logo now comes up after reboot.
So my question is how do I need to go about installing from internal memory once CWM 7.10 is running. Is there an adb command I'l need, or did I just choose wrong option?
Click to expand...
Click to collapse
You used the correct menu item.
If you used an sdcard version of the CM zip, it should have put it on the SD. You can tell by popping the SD out of the slot and booting. It should still boot to stock if you used the correct version. Then when you put the SD back in the slot it should boot to CM.
If you have it correct, then use the files in this thread to add the cyanoboot menu so you can boot back and forth without taking the card out.
Sent from my Nook HD+ running CM10.1 on emmc.
leapinlar said:
You used the correct menu item.
If you used an sdcard version of the CM zip, it should have put it on the SD. You can tell by popping the SD out of the slot and booting. It should still boot to stock if you used the correct version. Then when you put the SD back in the slot it should boot to CM.
If you have it correct, then use the files in this thread to add the cyanoboot menu so you can boot back and forth without taking the card out.
Sent from my Nook HD+ running CM10.1 on emmc.
Click to expand...
Click to collapse
Didn't use correct version...I'll have to find SD card version of CM 10, reload stock and try again.
Prof24 said:
Didn't use correct version...I'll have to find SD card version of CM 10, reload stock and try again.
Click to expand...
Click to collapse
You get the SD version the same place you got 7.1, verygreen's thread.
Sent from my Nook HD+ running CM10.1 on emmc.
Missing memory on SD CM10 boot
First post so I hope I'm putting this in the right place.
I have a Nook HD+ 32GB
I' ve started with Leapinlar's
[CWM/ROOT/EXTRAS] HD/HDplus Stock Root and other Mods
I've then used verygreen's
[Nook HD+] CM10.1 development for sdcard last update 09/04
All that seems to be fine but in CM10.1
Settings - storage reports internal memory 1GB and no SD memory or available mounts
x-plore reports /storage/emulated/0 and /Root as 850MB free of 1GB
Without the SD card - reverting to stock - I have 2.44GB used and 26.56GB available.
Is the 1GB apparently available on a partion on the SD card? I only had a 2GB SD going spare - this now has three partitions, the boot files and two others, one of 1GB. If I'd used a 32GB card would I have 31GB free?
But, more importantly, can anyone tell me how I get CM to give me my 32GB of internal storage back?
Please?
FWIW I expect to run CM10 from internal memory in the long run, but want to be sure that a couple of critical apps run OK before replacing the B&N stock.
Dave
davedamsons said:
First post so I hope I'm putting this in the right place.
I have a Nook HD+ 32GB
I' ve started with Leapinlar's
[CWM/ROOT/EXTRAS] HD/HDplus Stock Root and other Mods
I've then used verygreen's
[Nook HD+] CM10.1 development for sdcard last update 09/04
All that seems to be fine but in CM10.1
Settings - storage reports internal memory 1GB and no SD memory or available mounts
x-plore reports /storage/emulated/0 and /Root as 850MB free of 1GB
Without the SD card - reverting to stock - I have 2.44GB used and 26.56GB available.
Is the 1GB apparently available on a partion on the SD card? I only had a 2GB SD going spare - this now has three partitions, the boot files and two others, one of 1GB. If I'd used a 32GB card would I have 31GB free?
But, more importantly, can anyone tell me how I get CM to give me my 32GB of internal storage back?
Please?
FWIW I expect to run CM10 from internal memory in the long run, but want to be sure that a couple of critical apps run OK before replacing the B&N stock.
Dave
Click to expand...
Click to collapse
Everything is as it should be. You only have 1GB for 'sdcard' since you only used a 2GB SD. If you had used a 32GB, you would have close to 31GB for 'sdcard'.
And on an SD install, the internal memory is still there but not as 'sdcard'. It shows as a folder named 'emmc'.
Since you are planning on installing CM to internal memory, it will be even different yet. 'Sdcard' will be your internal memory and your external SD will be shown as ext_sdcard.
And do not pay too much attention to the settings/storage. People get very confused when reading that since it mixes apples and oranges. (Media storage and app storage).
Sent from my Galaxy Tab 2 using XDA Premium
leapinlar said:
Everything is as it should be. You only have 1GB for 'sdcard' since you only used a 2GB SD. If you had used a 32GB, you would have close to 31GB for 'sdcard'.
And on an SD install, the internal memory is still there but not as 'sdcard'. It shows as a folder named 'emmc'.
Since you are planning on installing CM to internal memory, it will be even different yet. 'Sdcard' will be your internal memory and your external SD will be shown as ext_sdcard.
And do not pay too much attention to the settings/storage. People get very confused when reading that since it mixes apples and oranges. (Media storage and app storage).
Sent from my Galaxy Tab 2 using XDA Premium
Click to expand...
Click to collapse
Finally...it worked! Thanks leapinlar, for all your help!
I encountered the situation above and am wondering if, say, instead of the 2GB card I use a 16 GB...that gives me 16 GB of storage for the CM 1.0 tablet, and my regular flash storage also stays 16 GB? Or all the apps are by default stored on the emmc?
Prof24 said:
Finally...it worked! Thanks leapinlar, for all your help!
I encountered the situation above and am wondering if, say, instead of the 2GB card I use a 16 GB...that gives me 16 GB of storage for the CM 1.0 tablet, and my regular flash storage also stays 16 GB? Or all the apps are by default stored on the emmc?
Click to expand...
Click to collapse
On the SD install, both media and apps get stored on the SD. If you use a 16GB SD to install CM to, it will have about 15GB available for media and app storage instead of 1GB on the 2GB card. But 2GB is really too small to be running CM. You will be running out of app and media storage very quickly.
Since you will be dual booting, when booted to stock the media and apps will be stored on internal memory. You will either have 13GB or 28GB available on stock on emmc depending on the size of the device (16 or 32GB model).
Sent from my Nook HD+ running CM10.1 on emmc.
Updating SD version of CM 10.1
I know I've seen this elsewhere, but can't find it...if I go to update the rom on the SD card, it makes sense to me that I would need to load the latest SD version from verygreen's page...or can I just update from settings and not lose dual boot? Also, will a dirty install work so that the data is not lost? (backups are always good )
Man we're enjoying dual boot. My Acer a500 is unreliable so I backed the "build a city town park" up with Helium app. Long story short, with dual boot my kid and I get to continue building and enjoying our monsters in "Monsterama Park" by booting to CM 10.1and restoring data, yet I don't have to give up some of the reader features that I really like with the original Nook OS. Marvelous find....again, thanks y'all for the hard work!
Prof24 said:
I know I've seen this elsewhere, but can't find it...if I go to update the rom on the SD card, it makes sense to me that I would need to load the latest SD version from verygreen's page...or can I just update from settings and not lose dual boot? Also, will a dirty install work so that the data is not lost? (backups are always good )
Man we're enjoying dual boot. My Acer a500 is unreliable so I backed the "build a city town park" up with Helium app. Long story short, with dual boot my kid and I get to continue building and enjoying our monsters in "Monsterama Park" by booting to CM 10.1and restoring data, yet I don't have to give up some of the reader features that I really like with the original Nook OS. Marvelous find....again, thanks y'all for the hard work!
Click to expand...
Click to collapse
Do not use settings to update an SD install. It will try to put the new ROM on internal replacing stock. Go get the latest SD ROM from the verygreen thread. You can dirty install it with the SD install's CWM.
Sent from my Nook HD+ running CM10.1 on emmc.
So there is no way to switch the menu for stock on sdcard?
leapinlar said:
Do not use settings to update an SD install. It will try to put the new ROM on internal replacing stock. Go get the latest SD ROM from the verygreen thread. You can dirty install it with the SD install's CWM.
Sent from my Nook HD+ running CM10.1 on emmc.
Click to expand...
Click to collapse
I'm a little confused. I've put verygreens stock on sdcard and have cm 10.2 on emmc. If the images are renamed can you boot with the menu into stock on sd or cm 10.2 from emmc? If not is there a second solution?
krash1256 said:
I'm a little confused. I've put verygreens stock on sdcard and have cm 10.2 on emmc. If the images are renamed can you boot with the menu into stock on sd or cm 10.2 from emmc? If not is there a second solution?
Click to expand...
Click to collapse
It does not work on that configuration and there is no solution.
Sent from my BN NookHD+ using XDA Premium HD app
Hello,
I am trying to use the mods posted Leapinlar in his excellent post here, but I am certainly doing something wrong since the internal and my SD card are not swapped. After installing the appropriate Zip file, I reboot my nook, but it does not see the Sd card anymore, it just shows the internal memory as both sdcard and ext_sdcard as if I do not have any memory card inserted. Once I remove the swap feature, everything works like before so I see both the internal memory as sdcard and my 16GB sd card as ext_sdcard. What I did
1.- I created the CWM 4GB card
2.- I copied both the SDSwap and remove SDSwap ZIP file on the CWM card
3.- Booted my nook with CWM card
4.- Chose to install the SDSwap Zip file
5.- Removed the card, inserted my 16GB sd card and rebooted
After that, with or without any SDcard inserted, the nook only shows the content of the internal memory as sdcard and ext_sdcard.
Thank you for any help for this silly newby here,
Miguel
Matoroa said:
Hello,
I am trying to use the mods posted Leapinlar in his excellent post here, but I am certainly doing something wrong since the internal and my SD card are not swapped. After installing the appropriate Zip file, I reboot my nook, but it does not see the Sd card anymore, it just shows the internal memory as both sdcard and ext_sdcard as if I do not have any memory card inserted. Once I remove the swap feature, everything works like before so I see both the internal memory as sdcard and my 16GB sd card as ext_sdcard. What I did
1.- I created the CWM 4GB card
2.- I copied both the SDSwap and remove SDSwap ZIP file on the CWM card
3.- Booted my nook with CWM card
4.- Chose to install the SDSwap Zip file
5.- Removed the card, inserted my 16GB sd card and rebooted
After that, with or without any SDcard inserted, the nook only shows the content of the internal memory as sdcard and ext_sdcard.
Thank you for any help for this silly newby here,
Miguel
Click to expand...
Click to collapse
What are you running, stock or CM10.1? If stock, it may be how you formatted the SD. If you used stock to reformat the card, the swap will not work. Get SDFormatter free on the web and format the SD. Then try the swap.
Sent from my Nook HD+ running CM10.1 on emmc.
leapinlar said:
What are you running, stock or CM10.1? If stock, it may be how you formatted the SD. If you used stock to reformat the card, the swap will not work. Get SDFormatter free on the web and format the SD. Then try the swap.
Sent from my Nook HD+ running CM10.1 on emmc.
Click to expand...
Click to collapse
That might be it. I am using stock and formated the card with it.
Thank you, I will try your solution.
Worked!!!!!
Matoroa said:
That might be it. I am using stock and formated the card with it.
Thank you, I will try your solution.
Click to expand...
Click to collapse
It worked. That was the solution. Thank you very much Leapinlar.
accessing internal memory
Matoroa said:
It worked. That was the solution. Thank you very much Leapinlar.
Click to expand...
Click to collapse
Thanks to leapinar and the junior op who started this post, i plucked up the courage to install sdswap. and its worked.
what i really want to know now is how to access my files on the internal memory? i use "es explorer" mainly, but if there
is another app that can access the internal memory that would be great.
I am using nook hd stock 2.1.1 with sideload mod and sdswap installed.
sunnysideup128 said:
Thanks to leapinar and the junior op who started this post, i plucked up the courage to install sdswap. and its worked.
what i really want to know now is how to access my files on the internal memory? i use "es explorer" mainly, but if there
is another app that can access the internal memory that would be great.
I am using nook hd stock 2.1.1 with sideload mod and sdswap installed.
Click to expand...
Click to collapse
ES Explorer is fine, but there are other file managers that also work. Root Browser, Root Explorer and many others. Just look in ext_sdcard as that is where internal memory is after the swap.
Sent from my Galaxy Tab 2 using XDA Premium