Hello, I have HTC Sensation XL and it fall to water but after it dry there is no backlight, I change the lcd but there still no backlight, someone knows where is the IC Backlight on the motherboard?
Thank you
enamorado1 said:
Hello, I have HTC Sensation XL and it fall to water but after it dry there is no backlight, I change the lcd but there still no backlight, someone knows where is the IC Backlight on the motherboard?
Thank you
Click to expand...
Click to collapse
there is a TPS 65200 IC on the board
it's located on the same side of the lcd connector, under the shilding,
if you look at the board with the battery connector towards the top, you can see on the right the si reader, in the middle the samsung memory chip,
on the left of the memory chip - you see a coil that says 100 on it, that's the backlight coil, and right next to it, to the left is the backlight IC.
i would start with the coil before trying to reball the IC.
thank you
SergioHeadAche said:
there is a TPS 65200 IC on the board
it's located on the same side of the lcd connector, under the shilding,
if you look at the board with the battery connector towards the top, you can see on the right the si reader, in the middle the samsung memory chip,
on the left of the memory chip - you see a coil that says 100 on it, that's the backlight coil, and right next to it, to the left is the backlight IC.
i would start with the coil before trying to reball the IC.
Click to expand...
Click to collapse
Anyone can mark picture of coil and the ic that i shoud change? Thanks a lot
enamorado1 said:
Anyone can mark picture of coil and the ic that i shoud change? Thanks a lot
Click to expand...
Click to collapse
Hi,
Same problem here.
In the green zone, the "coil" but as you can see in the red zone there is a kind of glue or something that melted. Do you have the same thing?
How can I replace the "coil" then ?!!
Related
My dumb butt child was sucking on my phone a couple weeks ago and caused the LCD to short out or something. The phone still worked and if I used a bright light I could shine it onto the screen and barely make out what was on the screen. It was booting properly and I assume that if I could make out the menu options the phone would still function. I assumed that she shorted out the LCD so I ordered, received and replaced the LCD tonight. Apparently this was not the problem, sucks to be me. I do think there was a problem with the touch screen portion already which is now working properly again but still I can still not see the screen for crap. It's like the brightness setting is on 1 or something. If I use a flashlight I can make out the screen, use the stylus and operate the phone. When I was replacing the LCD I noticed that the two circuit boards to the north and south of the LCD seemed to have a bit of corrosion on some of the tiny chips. I used an alcohol swab to clean the area off but that didn't make a difference. I am utterly convinced that the motherboard is fine since it seems to be well protected in the case and not easily accessible to moisture. I see no signs of corrosion on the motherboard like I do the two circuit boards around the LCD area. I noticed that there are only two contacts on the LCD one of which is a cable that plugs into the south circuit board just underneath the front panel key pad. Just to the right of that cable connection is where I saw signs of corrosion so I wonder if that board is the problem.
The computer tech in me says that I could be swapping parts all night before I get this right. Since the LCD plugs into that board, that could be the problem, there is a ribbon cable that wraps around the back of the LCD which also seems to make contact with the LCD which could also be the problem, that ribbon cable plugs into the north circuit board, so that might be a problem and finally, the ribbon cable plugs into the main board so that too might end up being a problem.
Can anyone take a guess as to why I might be seeing such low contrast/brightness from the LCD? I have already adjusted the brightness setting in the menus. I think it was called the backlight setting, but I moved them to the far right with no change. Again, this is a near pitch black screen that is only visible when I shine a light onto the screen.
i haven't taken my tilt apart but as a computer tech repairing broken laptops etc i know your problem.
as for laptops, there is a little inverter card that powers the backlight. its connected to the display unit by 2 cables (same as with my digital camera, rip ) and this boards are really weak / vulnerable to moisture...
so most likely this board is damaged...
That sort of explains what I think is going on too. Take a look at this cable (apparently it's clickable and will grow slightly in size to give more detail):
Let me explain the cable. This fits directly behind the LCD. The LCD comes with one flat ribbon cable and it plugs into a port on the right side of this picture. On that right circuit board if you notice the top left portion of the board there is thin black slot which is where the LCD plugs into if I recall correctly. There is another cable that plugs in just to the right of that jack from where I forget actually, lol. Once that cable is flipped over the bottom keypad on the phone sits right on top of that board. In fact on the other side you can even see the contacts for the outside buttons. The buttons in question would be like the green phone and red phone, the "e" shortcut and pretty much all the silver external shortcut buttons. Getting back to the cable, you will notice that in the middle of the cable there is a rather wide connection and that is the one that plugs onto the motherboard.
When I was replacing the LCD I spotted two sources of corrosion on both boards. The more plausible culprit was about 1/8 of an inch away from where the LCD plugs into the right circuit board.
I sent HTC an email seeing if they would help to which they told me to send it in. I have no intentions of doing that. I already know how to disassemble and reassemble the phone at this point and I already have 35 dollars invested into a new LCD. I am not about to spend 250 bucks to have HTC take 3 weeks to replace that cable. After some searching last night though, I have no idea where to get the cable. It seems that all the normal parts places on the web want 90 bucks for this cable, but at the same time they want 120 for the LCD. Obviously prices have dropped some because I was able to get the LCD new from ebay for 35. I just need help finding a place that will sell me that cable at a reasonable price.
Now that you have looked at the cable and that board, do you think it's possible that the right board could be the back light inverter that you were mentioning? If that's truly the correct board then it would make since that there is something wrong with it since I saw signs of possible damage and the LCD does work, just not strong enough to be seen with the naked eye. Since these things tend to work much like laptops do, I am leaning towards the possibility that you totally know what your talking about and that it would make since that this is the faulty part.
One other thought, the backlight is the piece that increases the brightness of the LCD right and not just some sort of overhead flashlight or something, correct? The term backlight almost implies a different part but I am pretty sure it's the term used to describe the brightness of the LCD in this case. I just wanted to make sure we were on the same page here.
Any additional thoughts?
Thanks
okay, to be clear about this. i am not 100% sure, if the backlight on the kaiser works the same way as the one on my IBM Thinkpad T41.
tl;dr; i don't know if the kaiser actually has an inverter board.
as for the cable: if you found a bit corrosion on both boards, i'm pretty sure that the reason why your backlight doesn't work.
about the last part: yeah, with "backlight" i mean the unit sits behind digitizer and LCD and increases the brightness of the lcd so you are able to read everything on the screen. i don't mean an overhead flashlight
btw, i just found this one
http://www.cellulardr.com/50H10051-41M-XC.htm
selling the cable / boards or about 90$
<edit>
disregard that... i noticed that the boards allways come with that cable assembly.... and cost about 90$ everywhere... will keep an eye on that.
</edit>
I'm going through the same thing. Did you ever replace that piece? Please let me know because it sucks to not use this phone.
I had a black g1 that had a broken power button and sticky keys, but its digitizer and touchscreen were intact. I purchased a white shell, installed everything, making sure the ribbons were fine, and now, I have a working g1 with power and good keys, but the digitizer isn't functioning.
Any way to diagnose this prior to me getting a new digitizer?
Recheck the ribbons.. they can pull out when you stick the case back together.
goldenarmZ said:
Recheck the ribbons.. they can pull out when you stick the case back together.
Click to expand...
Click to collapse
Looks like it won't seat firmly, and in my attempt to, the little black flip switch broke off ; would I have to get a new display or replace the ribbon port somehow? I'm bidding on some ebay bids for broken G1's so maybe I can salvage some components such as that ribbon to get the g1 back up to snuff.
New digitizer and screen later, I'm not having much luck. Same issue, screen works, digitizer nada.
Is there any other thing to check besides the connection between the display and digitizer and the display to the long ribbon extending down to the phone's motherboard?
princedwi said:
...
Is there any other thing to check besides the connection between the display and digitizer and the display to the long ribbon extending down to the phone's motherboard?
Click to expand...
Click to collapse
Indeed you may check for damaged components on your mainboard...
E.g. there's a level shifter for I2C interface with integrated ESD protection.
First check the output of your kernel with dmesg to make sure that the synaptics touchcontroller get's recognized during boot up.
If your kernel fails to register the driver for synaptics controller, there's something wrong with your hardware.
See the attachment for the location of the touch controller level shifter.
Regards,
scholbert
anyone know where to get the LCD connector on the motherboard from a Sprint HTC One?
as the picture shows, I've got a broken one that needs replacing.
It's 31 pins. The closing lever is on the back behind the slot to insert the LCD ribbon (white lever in picture). I think it's called an FPC or FFC connector. But I don't know the pitch.
thanks.
While I realize this post is some two years old, it came up pretty high on google search results, so I'm going to answer for the sake of anyone else that has this question and finds this post.
Code:
http://www.parts4repair.com/lcd-screen-fpc-connector-for-htc-one/
this appears to be exactly what you're looking for, but it looks to be a daunting task to replace.
Hi
I tried to replace my battery and after assemble it back i only get a black display when turning my m7 on.
I broke this little plastic thing from the display cable off (look in attachment)
Is this thing essential for a working display? (i thought i can fix it with a drop of glue)
Should the display work when the backcover is off the device? Because there are some connectors on the backcover....
cheers
00Nuclear00 said:
Hi
I tried to replace my battery and after assemble it back i only get a black display when turning my m7 on.
I broke this little plastic thing from the display cable off (look in attachment)
Is this thing essential for a working display? (i thought i can fix it with a drop of glue)
Should the display work when the backcover is off the device? Because there are some connectors on the backcover....
cheers
Click to expand...
Click to collapse
Shouldn't have done that, I think you accidentally broke something. I'd send it to a HTC service center. But that's gonna cost you probably.
nah, official repair isn't worth it. The phone is more than 2 years old...
and yes i think i broke something... thats why im asking
You're gonna have to be good with a solder and a couple of tiny wires if you want to revive your phone.
00Nuclear00 said:
Hi
I tried to replace my battery and after assemble it back i only get a black display when turning my m7 on.
I broke this little plastic thing from the display cable off (look in attachment)
Is this thing essential for a working display? (i thought i can fix it with a drop of glue)
Should the display work when the backcover is off the device? Because there are some connectors on the backcover....
cheers
Click to expand...
Click to collapse
You definitively need this clip to be intact so the flex cable sits firmly in place otherwise you'll have bad contact between the cable and the pins.
If you don't want to send to HTC for repair you'll need at least to send it to your local electronic repair shop so someone skilled with the proper soldering tool (not the standard iron you have at home) can replace the connector. BTW some of these clips must be lifted from the cable side and some other from the opposite side of the cable, so next time use tweezers and apply very light force on each side you'll find from what side it must be lifted.
LCD should work fine with the back cover removed, afaik. Connectors in the back cover are often for antennas but I wouldn't recommend to run the phone with antennas disconnected to avoid damaging the radio chips (reflected power).
If you are from the US, you can easily find this connector on ebay for about 10$. I'm sure it won't be that much expensive to repair if you bring the new connector and the phone already disassembled to your local repair shop.
Btw are you sure its only the LCD? When trying to boot the phone can you here the HTC theme or does it vibrate? Recognized by your computer when connected with usb?
thx for your response
I found an replacement part on ebay but first i have to look for someone who can solder this for me.
When i try to turn it on it only vibrates without a htc theme sound and there is no display reaction.
The other thing i mentioned is that the phone gets very hot in the middle (should be the cpu) where i dont know if it should get that hot.
I have to try the pc connetion again and let you know asap.
00Nuclear00 said:
thx for your response
I found an replacement part on ebay but first i have to look for someone who can solder this for me.
When i try to turn it on it only vibrates without a htc theme sound and there is no display reaction.
The other thing i mentioned is that the phone gets very hot in the middle (should be the cpu) where i dont know if it should get that hot.
I have to try the pc connetion again and let you know asap.
Click to expand...
Click to collapse
I'm not really worried about the absence of HTC sound when booting, if your phone is on silent / vibration mode, it will only vibrate when booting. If your computer does detect it once booted, then I guess the broken connector clip is the problem.
---------- Post added at 09:49 AM ---------- Previous post was at 09:27 AM ----------
Here is a video about the connector replacement, it doesn't look that hard to replace but wouldn't recommend to do it yourself if you never soldered electronics before. Soldering isn't that hard but you need some practices and knowledge to make good joints. I don't think your phone motherboard is a good candidate to practices yourself if you never did it before. You'll also need a really tiny tip for your iron, probably a type "L", 50/50 solder + some flux. Flux must be cleaned after use to avoid corrosion. The most difficult when soldering on motherboard, imo, is to find the right temperature. If your iron is to hot, you'll damage your connector. If its not hot enough, solder will take more time to liquefy and some heat will be absorbed by surrounding components which can cause irreversible damage.
Easy fix mate
You don't need to replace the connector, I've done this before, it is just the connector clip that has come off and it goes back on reasonably easily.
You will need a good magnifier.
You will need a good light source.
The phone held securely on its side with the socket pointing up.
Some masking tape on the loose part because it WILL go "ping" into the distance if you don't and you will not find it.
Look at the other connectors to see the proper orientation for the part, mark it with a permanent marker on top and at one end.
The insertion looks difficult, it isn't too bad, keep the part nice and straight and the motion is kind of like clicking it down on the ribbon.
Forget replacing the connector, that is 100 times harder.
If you do lose the loose part I have one or two laying around.
Good luck.
Good day to everyone!
I confronted backlight issue on my Z3 Compact when replacing LCD. When turning on the phone I couldnt see anything but phone responds to my touches. I took a flashlight and I pointed it directly at the display and I could barrley see icons.
So if you are having this issue follow my steps.
(Im not responsible if you fry your device do it at your own risk *I'm a professional*)
Remove motherboard from the frame and find SMD fuse has V on top of it on the mobo, lt's bellow metal frame that covers resistors and capacitators.
Remove or keep the fuse then get your soldering iron and heat it about 335°C. With slight touch make a jumper on the fuse, if you removed the fuse like I did just solder tiny wire on those 2 metal plates where fuse used to be soldered. Assemble it all and viollaaa your backlight will hopefully work again.
Guys if this helped you, hit me with that thanks means alot to me! Much love and good luck:angel:
kenzyyy said:
Good day to everyone!
I confronted backlight issue on my Z3 Compact when replacing LCD. When turning on the phone I couldnt see anything but phone responds to my touches. I took a flashlight and I pointed it directly at the display and I could barrley see icons.
So if you are having this issue follow my steps.
(Im not responsible if you fry your device do it at your own risk *I'm a professional*)
Remove motherboard from the frame and find SMD fuse has V on top of it on the mobo, lt's bellow metal frame that covers resistors and capacitators.
Remove or keep the fuse then get your soldering iron and heat it about 335°C. With slight touch make a jumper on the fuse, if you removed the fuse like I did just solder tiny wire on those 2 metal plates where fuse used to be soldered. Assemble it all and viollaaa your backlight will hopefully work again.
Guys if this helped you, hit me with that thanks means alot to me! Much love and good luck:angel:
Click to expand...
Click to collapse
helo @kenzyyy, it has help me when my phone was lost the backlight.. thank's for that
now i have a different issue, backlight is show but no display at all.. i still can touch, receive phone call, with scrcpy on my laptop i can see my phone work normally except the display not show
which one fuse to jumper for bringing the display back
i've post a thread HERE and still trying to find my solving problem..
thank's
sorry for my bad english