[Q] Screen black when I open keyboard (xt860) - Motorola Droid 3

My screen goes black when I open the keyboard. After I close it, it stays black and I have to take the battery out.
The light behind the buttons on the screen still comes on, and it seems like the blacklight behind the screen comes on. I tested it and if I recieve a call while it's doing this, the phone rings and the backlight lights up, but I cant answer because the screen stays black.
This is driving me crazy...
It's doing this on fresh stock rom and a fresh install of minimoto 1.7
Any idea why this is happening and how to fix it?

This happened to mt xt862. It was a bad or loose flex cable. Had it replaced and the problem was solved.
Sent from my XT862 using xda app-developers app

I thought it was my ROM at first too, but it is the flex cable going out. It gets worse over time until you can't use the touchscreen at all or the backlight doesn't turn on. When I opened my D3 up, there was a clean cut halfway across the cable.
I recommend mobiledefenders[dot]com > Droid 3 > Flex Cable
Here's the disassembly video I used:
www[dot]youtube[dot]com/watch?v=A_S9S9YLz7A
You will need a Torx 5 and Torx 3 (i used Torx 4 without issue)
Sorry for the lack of clickable links, I haven't met XDA's min post requirements yet

Related

[Q] Milestone screen not responding

I have had my Milestone for a while and it is out of warranty. Recently a narrow strip on the right side (when held vertically) of the phone has stopped responding to touch. It has decommissioned the search softkey, the backspace, L and the P key of the keyboard.
However, I have noticed that the touch response on the left has increased. For instance Q, A, and Z keys respond even if i touch the black edge of the screen, this goes for the back/return softkey as well.
This leads me to conclude that somehow my phone's inner working's alignment to the screen has been disturbed.
I have tried several roms...CM7, Froyomod and stock froyo but the problem remains.
I did use a third-party car charger once that gave me the ghost screen issue. Draining the batter to 0 with the app Battery Refresh and charging it to the full with Milestone charger solved the issue.
I'm in Bangladesh and there is no moto here...there is no support and sending the phone abroad for a fix is not an option. I'll have to fix it myself or save up for a few months to buy something else...not a bootloader locked moto again.
So, any suggestions? or directions I should be going or looking at?
1. The ghost touch appeared for me, too, after flashing FroyoMOD. I left the phone for ~a night slided-out, without battery, micro SD, SIM etc ) and it worked fine for ~5 days. Then, the same right side stopped working. We don't actually know what is the problem (moisture, bad charging, wear of the flex cable, defective digitizer) and we also can't be sure if we replace the digitizer the problem won't appear again. So, I suggest that you should sell the phone.
2. You could get an i9000, an LG 2x or a Desire HD.
L.E. I'm 95% sure that this isn't a software issue, so flashing different ROMs wont help.
same issue...
solution: dumped stone, got galaxy (Y)
My milestone eventually died. No M logo even. Thinking about getting a Huawei U8500 as an interim phone before I get something good.
Try Iphone insted
Once I got the same problem, it was not on the edge, but the middle of the screen & U, J & N keys stopped working. It was under warranty so I got the things replaced.
Touchwood

[Q] Phone works, screen does not yet sometimes it does

Hello
One night I was using the phone without doing anything special , some video watching . Phone went dark, tried to reboot. Blank Screen and the capacitive buttons flash. Left it to charge all night, in the morning it started but after I pressed the lock button blank screen but phone still working and receiving input.
Took the battery and SD card out left it for 30 seconds then started it again, Stuck at LG logo. Repeat , phone started ... Pressed lock button once then again to unlock , screen wouldn't start.
Used LG Mobile Update recovery tool to restore it ... Didn't solve problem. Sometimes it does not even start , just flashes buttons, other times it does without screen and last all works even the screen until first time goes dark , in the last two cases I can use LG On-Screen Phone without trouble, in doing so I installed a proximity sensor test app to see if it was causing my screen to not come back on , the sensor looked fine.
Facts:
1. Two day old Optimus Black p970, worked like a charm until stated problem
2. The app that checked proximity sensor showed the sensor to be free when my hand wasn't on it
3. The warranty laws in my country are idiotic so I would do or buy anything rather than send it so they can give me a new one in 3 months.
4. Tried another battery from another Optimus, fully charged nothing different.
5. Stock rom.
Do any of you fine people have some ideas on how to fix this? Thanks in advance
Hi there...
Sometime ago [1 year and a half or so~] I worked at a cell refurbishing facility [there were samsung, motorola and palm devices from sprint] and that problem you have was quite usual. Blank screen, still the phone is somehow usable like reciving calls...
There's this thing called "flex" which is the connector between board and display and that is what we fix, most of the time not even "fix it" just getting it in the right place...
This happen because of excesive use in those sliding or clamshell devices, in OB could be for overheating, you could try to fix it yourself or pay $20 usd [that's what it cost here]
Would that connector explain the fact that sometimes it doesn't start at all? hmm I am thinking now and I guess if it moves and somehow the phone feels it has not display connected it could fail to start... Anyhow thank you
actually yes, it could be only for the flex [some devices don't start at all when not having display or keyboard if there's any] but since our OB is not sliding nor clamshell type probably was overheating.
you say you have stock rom, well now I'm using CM7 but when I was at stock and after using the phone a few minutes it felt warm and some more minutes [like playing gunbros where you need to use both hands and a lot of movement] it was really hot and had to stop playing for a while.
what I'm trying to say is that because of overheating flex could have moved, but because of overheating too may have move something else, you couldn't belive the huge number of micro-things that reside in the board.
so if it's only the flex, it's an easy task to do, just unplug and plug again, but if it's something else it's quite hard to know just looking at it, you need to do some electric measures and stuff, the recomendation is to take it to a tech center or something
Hi. I Have same issue. Two times when i press power buton, butons flashing and screen still black. Phone not responding. I must remove baterry.
Sent from my LG-P970 using Tapatalk
Hi there, got the same problem too with my optimus black. Screen goes flickering, shut down don't do any good, and the phone temperature is kinda hot. But in my case it work after I clean some cache and data in the phone storage through LG OSP. After that, the phone temperature back to normal and the phone screen back to normal also. I believe that in my case the phone is overheated.

LCD Screen replacement

Thought this was going to be an easy repair. Obtained a new screen from Repair Universe (Really quick). Followed the video and several take apart guides. Put the phone back together, turned it on, Get the Motorola Logo screen, bottom keys light up and then the screen goes blank, Have to pull the battery to shut it down. SO, I put the old screen back in, turned it on, Motorola Logo again and the then the screen dims to where you can hardly see what's there, but it goes through the boot process. Anybody have any ideas as to what the hell I did to screw it up? Swapped the screens around several times hoping I'd remember something and magic would happen but no such luck!! Thanks, Howie
Replacing the Bionic's LCD is one of the simplest phone repairs I've ever done. It's possible you got a faulty screen, or it's possible that the LCD is not your problem. I've purchased from them a few times but never had a problem...might want to check what their return policy is.
Yeah, plug and play! Should have taken 30 minutes tops? What has me puzzled is the old screen dims right out now so I screwed something up? Sorta hoping this happened to someone else ans they figured it out before I send it in for repair.....
Sent from my ADR6350 using Tapatalk 2
meandg5 said:
Yeah, plug and play! Should have taken 30 minutes tops? What has me puzzled is the old screen dims right out now so I screwed something up? Sorta hoping this happened to someone else ans they figured it out before I send it in for repair.....
Sent from my ADR6350 using Tapatalk 2
Click to expand...
Click to collapse
Couple questions I had which may help clarify a few things, and could help in troubleshooting or finding someone who had a similar problem..
Why are you replacing the screen, was the screen dimming before you tried the replacement or only after?
Are you running stock blur or are you rooted/rom'd?
Information like that can go a long way to diagnosing the actual problems.
It's rooted and it's not a stock rom. I bought the phone and the LCD screen was damaged, so I ordered a replacement. I could still use it with the damaged screen but it had several white lines going down it. I rooted the phone and loaded a different rom before I switched screens and it was fine until I switched lcd's.
Sent from my ADR6350 using Tapatalk 2
It's probably a faulty LCD in that case, as long as the old LCD is working as it was. If not then perhaps you damaged the back light circuit.
The old screen doesn't work anymore. Correctly anyway. The old screen is real dim?
Sent from my ADR6350 using Tapatalk 2
I would have to agree with brandogg, could be the back light that is having the problem and that is why the old broken LCD is going dim now.
I'm assuming that the dimness problem occured only after the install of the replacement LCD since you only mentioned the lines as being the original problem.
One thing you could check is if the auto brightness is enabled. I would disable that and set the brightness as high as it will go and see if you still have the dimness issues.
That's when the dimness started on the old screen, after I installed the new one. I'll try to check the brightness after work. Thanks for the idea. I'll post back.
Sent from my ADR6350 using Tapatalk 2

[Q] Droid3 boot with white noise on screen fail to start

Hi Bros,
My droid3 has been acting up for a week now and I should have done something about it but didn't get a chance. What happened was whenever you would slide out the physical keyboard the display would go off. Sometimes the phone would still work but no display. Sometimes I would restart the phone by taking out the batter an the display would be a white screen with multi colore noise. I could get the phone back on by moving the keyboard in and out a couple times. I've been able to use it until today, and I didn't back up my stuff.
Now today I've been trying to get it started but all I get is the white screen. I just need a couple minutes to get a couple more things off of it. I've been trying all day and was wondering if anyone had any ideas. I need to go to the store and hope it is covered still. I have taken good care of this phone since I got it. Still i can able to turn the screen on evertime when i booth it with an open slider keypad. and some lucky times it does nothing if after words i close the slider but most of the time after starting if i close the slider screen goes black and phone is still runing in the back
If any one can help me with my droid3
Thanx
Hmmmn..did you drop ur fone? It looks like the ribbon on the digitizer is probably cracked, broken, shorted or come loose partially and is defective..this could be causing the white screen. Try re-seating/replacing the touch digitizer's flex-cable.
its the ribbon cable or LCD screen both can be replaced, kind of a pain, look on ebay, brake down links in my list
sd_shadow's list of links for Droid FAQs, SBF, Rooting, ROMs.... https://docs.google.com/document/d/1Goawxdx_UBF4Y8lqzHYWf8Ha3yUcRK4faq0UWIlXLWA/edit
Sent from my XT862 using xda premium
Had the same thing happen to two D3s. Both times it started happening occasionally, then within 2 weeks it happened every boot. One went back to Verizon for an exchange, and the other is sitting in a drawer. Please let me know how you fix this, if you do fix this.
I fixed mine, by replacing the lcd screen, but your flex cable could be the problem too
http://www.ebay.com/itm/USA-Motorol...249?pt=LH_DefaultDomain_0&hash=item4ab523f419
http://www.repairsuniverse.com/motorola-droid-3-screen-repair-take-apart-guide.html
---------- Post added at 09:51 PM ---------- Previous post was at 09:40 PM ----------
Motorola Droid 3 XT862 Main LCD Slide Flex Ribbon Cable
http://www.ebay.com/itm/230761271827?ssPageName=STRK:MEWNX:IT&_trksid=p3984.m1439.l2649

[Q] [HELP] Black Screen but Functional Device. Galaxy Note N7000

Hello Everyone!
So i'm really stuck over here. I have an international Samsung Galaxy Note N-7000 that is working but with a black screen!
First of all i want to discuss exactly what i have done:
1.i had a problem with the charging port where it works sometimes and most of the times doesn't. So i decided to order a new charging port to replace the existing one.
2. When i received the new charging port i instantly started to dissemble the device (The device was working perfectly before starting replacement)
3. After i removed the old one and installed the new, i turned on the device and it showed only a black screen, then after some time i saw the touch buttons light, but still the screen is black:crying:
4. so i decided to return back the old charging port and this time when i turned on the device it sounded like it's booting and working but still with a black screen. The phone even received call and the touch screen is working but with black screen.
What do you guys think has just happened to my phone? could the new charging port cause any problems with the motherboard?
i'm really stuck and don't wanna go to a service center
I have recorded a video of the problem. Please see it below
since i'm new over here, i'm not allowed to post youtube link.
please head to youtube and type my username and watch the video : nadeaa0a
thank you very much
My younger brother always liked to disassemble things with a hammer wondering after why it wasn't possible to assemble it the other way around.
It took him a few years to understand that real knowledge of things is a clear advantage.
Go to a service center and get help from a professional instead of making it ...
Sent from my GT-N7000 using xda premium
maybe you disconnected the wire you were changing ports ! don't worry and don't freak out just take to any shop and they will check it i don't think the screen is burnt because if it was it would be more expensive ! go to any shop and ask them to change ports and check the screen
for what you described, my best guess would be either you unplugged the lcd and didnt plug it back in properly.... or you damaged the flex for the lcd... the charging flex wouldnt cause the problem... just inspect the lcd flex and plug for damage... if no visible damage plug it in again and try it again... lets hope its just not plugged in right...
I have the same problem
Hi,
I have the same problem. I had never disassembled my phone and the screen slowly turned purple and started blackening out. It was fully functional. This I knew because I connected it to my Windows 7 computer and used Android Commander. I ordered a new screen complete with bezel etc. I have two batteries, the first didn't even charge after I put it in the phone (it had drained totally during the wait for the new screen), the second was partially charged and allowed the screen to boot. It is however behaving like the first screen did before it went black, that is purple. I am sure I have not done anything wrong with the connections. Could it be the batteries? or the adapter flex? I just hope it is not the mainboard. It is not on warranty and we don't have that many honest phone specialists around where I live. I am almost sure others have experienced the same problem and someone on xda knows what the problem is. If you do I would be indebted.
nadeaa0a said:
Hello Everyone!
So i'm really stuck over here. I have an international Samsung Galaxy Note N-7000 that is working but with a black screen!
First of all i want to discuss exactly what i have done:
1.i had a problem with the charging port where it works sometimes and most of the times doesn't. So i decided to order a new charging port to replace the existing one.
2. When i received the new charging port i instantly started to dissemble the device (The device was working perfectly before starting replacement)
3. After i removed the old one and installed the new, i turned on the device and it showed only a black screen, then after some time i saw the touch buttons light, but still the screen is black:crying:
4. so i decided to return back the old charging port and this time when i turned on the device it sounded like it's booting and working but still with a black screen. The phone even received call and the touch screen is working but with black screen.
What do you guys think has just happened to my phone? could the new charging port cause any problems with the motherboard?
i'm really stuck and don't wanna go to a service center
I have recorded a video of the problem. Please see it below
since i'm new over here, i'm not allowed to post youtube link.
please head to youtube and type my username and watch the video : nadeaa0a
thank you very much
Click to expand...
Click to collapse
it shows as color black, or nothing (like locked device)? I used to face this problem too with my infuse 4G, but it was because of installing custom rom. Had problem with few rom i installed but nothing happen on my stock one. If your device is just not lighting up(like locked device), then i guess because of ROM, but i'm not sure yet. But if it shows "color black", then i don't know.
THIS IS NOT A SOFTWARE BUG. Its the Screen flex or the ribbon. Disassemble the back part, and take a look at the flex or the ribbon connector of the screen, clean the conector with a tooth cleaner with alcohol and let it dry for a few minutes. Put it back on and mount the back part again. Test it, it should work.
Same thing here: changed the usb port, booted fine, had issues with the sim, turned off took it apart again to check, put it back on and black screen.
Yea having the same issue here, dismantling the usb module and put in new one, power up black screen!! The menu and back button did lights up, and the phone is working too, can hear the booting tone, anyone got any solution for that yet?
jasonhs said:
Yea having the same issue here, dismantling the usb module and put in new one, power up black screen!! The menu and back button did lights up, and the phone is working too, can hear the booting tone, anyone got any solution for that yet?
Click to expand...
Click to collapse
You damaged your LCD flex cable or didn't plug it in correctly ..
N00b... said:
You damaged your LCD flex cable or didn't plug it in correctly ..
Click to expand...
Click to collapse
I have unplugged and replug back few times, same result. Guess most probably i have damaged the flex cable. Replacement part seems too pricy to change, rather buy a new phone.
Sent from my GT-P6800 using Tapatalk

Categories

Resources