hi im new here as a member of xda but hae learned a ton by reading around the site. ive currently ran into an issue with my atrix hd (mb886) i updated the firmware i tried multiple versions to see if the problem was with the file. even with stock firmware if i dont use a rom i get stuck on motorolla screen. i have cwm revocery. my bootloader is unlocked and before i updatd the firmware my phone was rooted. so at this point i tried installing multiple roms. 1: CM =bootloop 2:jellybam=bootloop 3:btakang rises- screen passes the motorolla screen and goes to a black screen that flashes every 6 seconds. my fastboot menue reads the following
normal power up
recovery
ap fastboot
factory
bp tools
when ii enter ap fastboot this is what i see
ap fastboot flash mode (s)
10.9B(*) (sha-ca705b9,2013-02-17 18:17:55)
eMMC info: size 8gb
device is unlocked, status code:3
battery ok
transfer mode
fastboot reason:boot menue selected (that sometimes changews to sticky etc only if im connected and flashing firmware via command promt on laptop)
im not sure what i need to do to fix my phone at this point if i can get the thing to turn on idc what rom or firmwar i use lol thanx alot in advance
Related
Hello, I'm the owner of a bricked Droid Bionic. I purchesed it from someone that tried to root it, not is just boots into fastboot (with errors if you let it just start, and 0A.61 AP FastBoot Flash Mode (S) if you do the up/down power button method.
I've used RSD Lite 5.7 several times with all the VRZ files I can find. Most stop at step 6 with "Phone Fail" and occasionally at step 2 USB Error read/write (basically).
These are the file names I've tried:
VRZ_XT875_5.5.893.XT875.Verizon.en.US_CFC_01.xml
VRZ_XT875_5.9.905.XT875.Verizon.en.US_CFC.xml
VRZ_XT875_6.7.246.XT875.Verizon.en.US_CFC_01.xml
VRZ_XT875_6.7.246.XT875.Verizon.en.US_CFC_01_Dfib
Most files I find are no longer active and the links fail or lead to some bloated download site that requires registration etc to use.
I'm also normally running Linux but since trying to repair this phone I installed XP SP3 "just for the Bionic".
Thanks for any help, guidance etc ..
If I just let the phone boot as normal it goes to a broken fastboot screen:
AP FastBoot Flash Mode (S) (Flash Failure)
0A.61
Battery OK
OK to Program
Connect USB
Data Cable
Thank you.
Fixed
I finally got it to finish the push from FastBoot. I used a cable from my HTC Incredible 2, on a USB 1.0 port and it finally went through.
67comet said:
Hello, I'm the owner of a bricked Droid Bionic. I purchesed it from someone that tried to root it, not is just boots into fastboot (with errors if you let it just start, and 0A.61 AP FastBoot Flash Mode (S) if you do the up/down power button method.
I've used RSD Lite 5.7 several times with all the VRZ files I can find. Most stop at step 6 with "Phone Fail" and occasionally at step 2 USB Error read/write (basically).
These are the file names I've tried:
VRZ_XT875_5.5.893.XT875.Verizon.en.US_CFC_01.xml
VRZ_XT875_5.9.905.XT875.Verizon.en.US_CFC.xml
VRZ_XT875_6.7.246.XT875.Verizon.en.US_CFC_01.xml
VRZ_XT875_6.7.246.XT875.Verizon.en.US_CFC_01_Dfib
Most files I find are no longer active and the links fail or lead to some bloated download site that requires registration etc to use.
I'm also normally running Linux but since trying to repair this phone I installed XP SP3 "just for the Bionic".
Thanks for any help, guidance etc ..
If I just let the phone boot as normal it goes to a broken fastboot screen:
AP FastBoot Flash Mode (S) (Flash Failure)
0A.61
Battery OK
OK to Program
Connect USB
Data Cable
Thank you.
Click to expand...
Click to collapse
Hi people, I have a big problem with my friend's Razr i, I was trying to root it, but i didn't want to unlock my bootloader so tried several methods but not a single one worked, So i tried the one for unlocked bootloaders and ended up bricking my device, Now It's stuck on fastboot mode.
I've tried to flash some brazilian firmwares via RSD lite, but it get stuck on "6/9 flashing radio_signed" SO PLEASE SOMEONE GUIDE ME TO THE SOLUTION WHAT AM I DOING WRONG?
PS: Also tried to flash an argentinian Firmware but it didn't even let me start flashing bringing the error "Faled flashing process. Unknown fastboot command. (getvar)"
PS2: Also tried the eternityprj Alternate method without RSD, and it gets stuck on flashing recovery... and it also prompts some errors you can see in the attached file.
HELP ME PLEASE AS I SAID THE RAZR IS A FRIEND'S PHONE NOT MINE, I NEED TO SAVE IT.
Vaizen said:
Hi people, I have a big problem with my friend's Razr i, I was trying to root it, but i didn't want to unlock my bootloader so tried several methods but not a single one worked, So i tried the one for unlocked bootloaders and ended up bricking my device, Now It's stuck on fastboot mode.
I've tried to flash some brazilian firmwares via RSD lite, but it get stuck on "6/9 flashing radio_signed" SO PLEASE SOMEONE GUIDE ME TO THE SOLUTION WHAT AM I DOING WRONG?
PS: Also tried to flash an argentinian Firmware but it didn't even let me start flashing bringing the error "Faled flashing process. Unknown fastboot command. (getvar)"
PS2: Also tried the eternityprj Alternate method without RSD, and it gets stuck on flashing recovery... and it also prompts some errors you can see in the attached file.
HELP ME PLEASE AS I SAID THE RAZR IS A FRIEND'S PHONE NOT MINE, I NEED TO SAVE IT.
Click to expand...
Click to collapse
your secure level was to high for a non bootloader method and if you done a method with a unlocked bootloader and your bootloader was locked thats bad.
unlock your bootloader >>WARRANTY VOID<< install cwm and use any backup. or flash the 39 gb fw but i think you have yet to unlokc the bootloader to safe it.. and be patient dont try to much stuff if your battery goes low you need a factory adapter or something like this to charge ur razr i if the battery is down.
regards hope you get it waorking again
I solved my problem this way
Vaizen said:
Hi people, I have a big problem with my friend's Razr i, I was trying to root it, but i didn't want to unlock my bootloader so tried several methods but not a single one worked, So i tried the one for unlocked bootloaders and ended up bricking my device, Now It's stuck on fastboot mode.
I've tried to flash some brazilian firmwares via RSD lite, but it get stuck on "6/9 flashing radio_signed" SO PLEASE SOMEONE GUIDE ME TO THE SOLUTION WHAT AM I DOING WRONG?
PS: Also tried to flash an argentinian Firmware but it didn't even let me start flashing bringing the error "Faled flashing process. Unknown fastboot command. (getvar)"
PS2: Also tried the eternityprj Alternate method without RSD, and it gets stuck on flashing recovery... and it also prompts some errors you can see in the attached file.
HELP ME PLEASE AS I SAID THE RAZR IS A FRIEND'S PHONE NOT MINE, I NEED TO SAVE IT.
Click to expand...
Click to collapse
Hello good morning
I brick 2 phones trying to get one of them and in the process did fail at 2, how the recovery?
1. - Use RSD Lite version 6.1.4
2. - Use 1 extra phone (htc wildfire root and backup CWMR in case of failure)
3. - Use a GB retail rom (CFC_8.7.1I-110_IFW-39_S7_UCASMI01E1017.0R_USASMIICSRTGB_P042_A005_S1FF_fb.xml)
4. - The phone to unbrick, put fastboot mode, switching on via the power button and vol (-) until the fastboot mode screen read "fastboot reason:" if it does not, re-try until there is
5. should not say "fastboot reason: flash failure, or anything else xxxxxx xxxx xxxxx ............"
6. - Boot rsd lite 6.1.4, select retail rom, and indicate that only "unzip" connects your motorola razr I, and it connects back to the other phone (in my case htc wildfire), which has a debug mode enabled.
7. - Note, that in the window of the Rsd Lite in row 1, the Razr I phone is detected, then you start flashing in RSD Lite 6.1.4, see screenshot of your razr I to see that data is being sent, (the other phone should not be affected and only serves as a decoy to usb drivers, Rsd lite at least do not damage to my phone)
8. - Remember flashing erase the card was in your internal Razr I therefore will lose programs, photos or music you had or downloaded to the SD or internal virtual
9. - Flashing can stop and have to do everything again, but remember that no fastboot mode screen should read:
"fastboot reason: flash failure or otherwise else xxxxxx xxxxxxx ......." must be clean that is just:
"fastboot reason: "
luck : Good:
Warning, do not take responsibility for any damage to your cell involved in the process, ......... the lure of the phone can be found on youtube and just suits the way because of my need to get my phone ........ in no way am programmer or software developer, for which only comment what turned out ok to me
excuse my bad English
jacbarahona72 said:
Hello good morning
I brick 2 phones trying to get one of them and in the process did fail at 2, how the recovery?
1. - Use RSD Lite version 6.1.4
2. - Use 1 extra phone (htc wildfire root and backup CWMR in case of failure)
3. - Use a GB retail rom (CFC_8.7.1I-110_IFW-39_S7_UCASMI01E1017.0R_USASMIICSRTGB_P042_A005_S1FF_fb.xml)
4. - The phone to unbrick, put fastboot mode, switching on via the power button and vol (-) until the fastboot mode screen read "fastboot reason:" if it does not, re-try until there is
5. should not say "fastboot reason: flash failure, or anything else xxxxxx xxxx xxxxx ............"
6. - Boot rsd lite 6.1.4, select retail rom, and indicate that only "unzip" connects your motorola razr I, and it connects back to the other phone (in my case htc wildfire), which has a debug mode enabled.
7. - Note, that in the window of the Rsd Lite in row 1, the Razr I phone is detected, then you start flashing in RSD Lite 6.1.4, see screenshot of your razr I to see that data is being sent, (the other phone should not be affected and only serves as a decoy to usb drivers, Rsd lite at least do not damage to my phone)
8. - Remember flashing erase the card was in your internal Razr I therefore will lose programs, photos or music you had or downloaded to the SD or internal virtual
9. - Flashing can stop and have to do everything again, but remember that no fastboot mode screen should read:
"fastboot reason: flash failure or otherwise cuarquier xxxxxx xxxxxxx ......." must be clean that is just:
"fastboot reason: "
luck : Good:
Warning, do not take responsibility for any damage to your cell involved in the process, ......... the lure of the phone can be found on youtube and just suits the way because of my need to get my phone ........ in no way am programmer or software developer, for which only comment what turned out ok to me
excuse my bad English
Click to expand...
Click to collapse
Could PM Me with the instructions in spanish, there are some things that i do not understand in your english
Tried to use your method but RSD lite got stuck on "4/11 erase userdata" and the phone says "program dummy sp block for userdata" I don't thin I understood well the part of the second phone, does it have to be on, i mean normal on, or does it have to be in flashmode aswell?
Hello, thanks for your time, I need Help. I have been reading the whole day with no results.
1. what i have: I have the Atrix hd from AT&T sim unlocked, bootloader unlocked, CWM v6.0.2.8, it charges by using bp tools while connected to usb charger. now it is 100%.
2. the problem. I can´t make it go up, it can get to fastboot and CWM, when I try to make it start normally it goes to the bootloader unlocked screen and stays there then turn off and goes to the same screen again, when I connect it to the pc while it's off it then turn on to the fastboot and the pc recognizes it as unknown device , the fastboot says.
AP Fastboot Flash Mode (S)
10.9B(*) (sha-2e68372, 2012-11-17 23-33-08)
eMMC Info: Size 8GB
Device is UNLOCKED, Status Code: 3
Battery OK
Transfer Mode:
USB Connected
Fastboot Reason: Flash Failure
else I can go there by using the +, - and Power button, and selecting Fastboot, and it changes the
USB Connected -> Connect USB
Flash Failure -> Menu Selected.
if i connect to the pc it says nothing, I have tried with different PCs and usb cables, also I tried using "Fastboot Reboot"? on my father's Atrix 2 with the same cable and it worked.
I can not mount /data or /sdcard, but i can mount the xternal sdcard.
I have been looking for a Update.zip for the Atrix HD, but nothing found, also the Atrix HD is not supported by the kitchen, it is to flash stock JB with CWM.
how i got there?
first I Rooted, and unloked bootloader with myth tools, i was in Stock JB,
then I instaled CWM and flashed Pacman pac_mb886-nightly-20131222,
then flashed stock ICS 7.7.1Q-115_MB886_FFW-14_SIGNED_CFC.xml.zip with Myth,
then I started geting the Unknown Device and could'nt mount the phone on the pc, even in fastboot,
then flashed back pacman, but the problem kept going,
then tried flashing JB with Myth and manually using the CMD Fastboot and the script of flashing.bat in the myth and the phone died, it went fine until flashing modem from then on it said failed directory doesnt exist, or device not found, or too many links.
again thanks.
EDIT: Thanks for all of those who say my post, editing here to tell you how I managed to fix it.
first I went into CWM, then mount and format -> format data and data media, (Sdcard), something I didn't want, coz I lost all my data and bakups, but anyway i clicked it hopping it wouldnt function, but it did, wen I saw succes.
formated system, data, cache, dalvik, mounted external sd, and instaled pacman, and gaps, that i had there, then reset system now.
it went to fastboot reason flash failed, turned off.. vol + & - , star normally, it went to warning bootloader unlock and finally pacaman bootanimation, I saw glory.
Now I just have to fix the fastboot booting and the warning but reading ill get it.
Glad you got it working. You should also update to the latest cwm or Philz for recovery.
Yes, and you can install Philz Touch recovery zip from within CWM - then you can install the KK ROMs.
Hello all together,
i end up here because i could not find any other Resolution on the net to get a rooting working ! So perhaps someone can give me an advise on this !?
I am working now since a week on this problem to get my HTC on Max rooted but nothing seem to work, several downloads from the net and studi all of the existing Youtube videos with al lot of houres of trying and working on this.
What i have:
HTC one Max with 4.3 date 27.11.2013 and htc sense 5.5, 11GB with 32 GB SD (in the monent no Sim installed)
What i already did with success:
Aktivated Developers mode and USB Debugging (get adb Device and fastboot device to see my phone in PROMPT)
Under Powersettings Disabled "FASTBOOT"
Unblocked the Bootloader, so i see in the fastboot of the phone in the first lines the Information *TEMPERED* and in the seconfd line *UNBLOCKED* so that means that all this work is done O.K. without any Problems also to flash offcorse the right ROM image.
(this i did with the Prompt fastboot method: fastboot flash recovery ......img, then fastboot clear cache).
Copyed the SU to Root of Phone to make then after recoveryrestard the root. -Latest Verion-
So here now the Problem where i stuck since some days and Nights without any resolution:
After all done (up mentioned) i go with Vol Down and Power to fastboot and choose the second line Recovery and confirm with Powerbutton (after a while the phone suppose to enter into the recovery so that i could choose the SU-ZIP - the normal way), but now the Phone reboots into white screen and shows on top Pink line like Phone Recovery (this all still looks good), then nothing happens (where it supose to start after that my rom to enter and choose the SU-ZIP).
It just turns off after a while to black screen and reboots normaly like i turn the phone on up into the normal Phone-Desktop !
So it was not entering into the recovery and with this i could not start the SU-ZIP, so the phone is not rooted.
Thanks for any help and sugesstion (sorry for my bad english)
So do you have any idear what i perhaps have maked wrong !? or do i have to downgrade the Phone perhaps to 4.2 !?
hi, i have a problem:
i tried to unlock my boot loader and instal a recovery (specifically the PhilZ Touch Advanced CWM Recovery), apparently the unlock did't work, i did not see that and i proceeded to install the recovery, the device reboot on the AP fastboot flash mode and says:
Device is LOCKED. Status Code 0
Battery OK
Connect USB
Data Cable
Fastboot Reason Flash Failure
now when always i press the button on, the device boot on the AP fastboot flash mode.
I can boot normally acceding to the boot menu pressing the 3 side buttons (+/- on) , but i want to solve that problem because i really want to unlock the boot loader
help please and thanks
(sorry for my english)
How did you try to unlock your bootloader?
Sent from my ATRIX HD using XDA Free mobile app
First off, would you kindly give us more information? We need to know what method you used to unlock your bootloader, your operating system, and your phone's original carrier to fully assist you. As it stands, you best bet is to ensure you have to correct drivers for adb and fastboot, then use RSDlite or Mythtools to flash the correct fastboot file to your phone.
I use the motopocalypse method for unlock the bootloader (but apparently didn't work), i have jelly bean and orignally is from nextel (mexican carrier) but a change it to telcel (also mexican)
Have you tried reflashing the stock jb Mexican sbf files? You can find them in the help and troubleshooting section.
there is no problem if i try to flash it when i have the bootloader locked?
You can flash stock roms even when bootloader is locked....
Sent from my ATRIX HD using XDA Free mobile app
can i flash it whit myth tools? (sorry for the noob question)
edit: i download the stock rom and extract the recovery, i flash it with myth tools and now everything is ok
Tthanks for the help
another problem
now i tried to unlock the boot loader but before the process start, in the console appears the message "TrustZone Write Failed -11"
exist a solution for that?