[Q] [Help] Hard Bricked Xperia PC Recognizes as "qhsusb_dload" - Xperia Z Q&A, Help & Troubleshooting

Is there any solution?
DUMB ERROR HERE!!!!
I was flashing a rom but i make a big mistake and install another rom instead,( i use my phone as a usb sometimes! i forget to delete this rom from my sd card) :crying: MIUI for GALAXY S3 or something! Battery was over 86%
PROBLEMS:
1- No Leds (NO is NO!)
2- Phone doesnt vibrate ( not even hard keys combos, not anyones! )
3- Conecting to PC and PC doesn recognize Phone Sound alert for usb not dirvers
4- device manager shows my phone as "qhsusb_dload" with yellow alert for no drivers.
5- Flashtool doesnt see my phone on eny mode Fastboot or Flashtool
Any help?
I hope find a method to trick the driver an tell my pc is a XPERIA Z....
Any solutions?
THANX IN ADVANCE GUYS!

I also had that prob before after my phone get into the water. What i mean is water damage. What i did is leave the phone around 1 to 2 days.then charge it.miracles happen,my phone suddenly boot up.
Sent from my C6603 using xda app-developers app

mcyorian said:
Is there any solution?
DUMB ERROR HERE!!!!
I was flashing a rom but i make a big mistake and install another rom instead,( i use my phone as a usb sometimes! i forget to delete this rom from my sd card) :crying: MIUI for GALAXY S3 or something! Battery was over 86%
PROBLEMS:
1- No Leds (NO is NO!)
2- Phone doesnt vibrate ( not even hard keys combos, not anyones! )
3- Conecting to PC and PC doesn recognize Phone Sound alert for usb not dirvers
4- device manager shows my phone as "qhsusb_dload" with yellow alert for no drivers.
5- Flashtool doesnt see my phone on eny mode Fastboot or Flashtool
Any help?
I hope find a method to trick the driver an tell my pc is a XPERIA Z....
Any solutions?
THANX IN ADVANCE GUYS!
Click to expand...
Click to collapse
install usb drivers manually
if u r on win8 u should know to disable driver signature and etc (all tutorials are available)
then to find solution calm down, and check what did u do exactly step by step
not deleting another rom (i m opinion) cannot cause hard-brick cause almost of custom recoveries wipe everything themselves before start to flash new rom...
:good:

x102x96x said:
install usb drivers manually
if u r on win8 u should know to disable driver signature and etc (all tutorials are available)
then to find solution calm down, and check what did u do exactly step by step
not deleting another rom (i m opinion) cannot cause hard-brick cause almost of custom recoveries wipe everything themselves before start to flash new rom...
:good:
Click to expand...
Click to collapse
im not sure its so simply as connect the phone to charge, i mean, the phone was flashed by a rom designed for another phone!...
SONY XPERIA Z flashed by accident with a customn miui rom for GALAXY S3, as a result the phone is dead, no minimal responses, no vibs, or led, flashtool doesn works, and the only thing is the phone is seen bypc as "qhsusb_dload" unknown decvice.
About manually installed drivers... whats drives? Sorry for my english and thanks a lot for tour help!

mcyorian said:
im not sure its so simply as connect the phone to charge, i mean, the phone was flashed by a rom designed for another phone!...
SONY XPERIA Z flashed by accident with a customn miui rom for GALAXY S3, as a result the phone is dead, no minimal responses, no vibs, or led, flashtool doesn works, and the only thing is the phone is seen bypc as "qhsusb_dload" unknown decvice.
About manually installed drivers... whats drives? Sorry for my english and thanks a lot for tour help!
Click to expand...
Click to collapse
i don know what device is for xperia
but sth called Box is for galaxies that can reinstall rom from initial binaries... so it can help to recover almost dead phone
and some special tools again for galaxies, like g-tag or ...
i know them cause i hard-bricked my s3
But i didn't have any access to these tools... so my my s3 pasted away...
for ur situation; search more for these kindda tools and take it asap to pro. service or professional hardware engineer
good luck
:good:

Do you have ADB set up? See if ADB recognizes fastboot mode. Then maybe you can fastboot flash. But as far as I can tell with my limited knowledge the bootloader seems to be corrupted, which is probly irrepairable. Maybe you can get some of the real devs to help you if you ask nicely enough, I'm just a lurker...

mcyorian said:
Is there any solution?
DUMB ERROR HERE!!!!
I was flashing a rom but i make a big mistake and install another rom instead,( i use my phone as a usb sometimes! i forget to delete this rom from my sd card) :crying: MIUI for GALAXY S3 or something! Battery was over 86%
PROBLEMS:
1- No Leds (NO is NO!)
2- Phone doesnt vibrate ( not even hard keys combos, not anyones! )
3- Conecting to PC and PC doesn recognize Phone Sound alert for usb not dirvers
4- device manager shows my phone as "qhsusb_dload" with yellow alert for no drivers.
5- Flashtool doesnt see my phone on eny mode Fastboot or Flashtool
Any help?
I hope find a method to trick the driver an tell my pc is a XPERIA Z....
Any solutions?
THANX IN ADVANCE GUYS!
Click to expand...
Click to collapse
qhsusb_dload= qualcomm driver needed(but it wont change any thing). Only boot repair can solve this problem nothing else.
Ask riff box users about help.

robdevil said:
qhsusb_dload= qualcomm driver needed(but it wont change any thing). Only boot repair can solve this problem nothing else.
Ask riff box users about help.
Click to expand...
Click to collapse
Thanks!!! where can i find these people ? (riff Box Users?)

@[NUT] has a disaster recovery thread. He may be able to work some magic for you :fingerscrossed:
Sent from my C6603 using xda app-developers app

shoey63 said:
@[NUT] has a disaster recovery thread. He may be able to work some magic for you :fingerscrossed:
Sent from my C6603 using xda app-developers app
Click to expand...
Click to collapse
We where actually already working on a possible solution, he found my thread on his own

Help Needed
mcyorian said:
Thanks!!! where can i find these people ? (riff Box Users?)
Click to expand...
Click to collapse
have you found any solution because I am experiencing the same issue

Same Problem
Hi friends I have the Same problem With my xparia lt26w (acro s)
I think when the device has no kernel same thing would happen.
As I know Samsung users Made a program that save phones from Hard brick
Is there any way to write the same program for xperia devices???
Or If any boady knows a box that support Sony devices boot Repair???
I try riff 2014 box but Nothing happend and Not supported.
Any help Frome Developers plz???

I have the same problem, I try to install another rom on SXZ. I try QSTP and HDDrawCopy, but I need the files of bootloader for fix this issue, but I don't know where to find it.
This is my post http://forum.xda-developers.com/showthread.php?t=2639444

UPDATE
has been long time since my XZ was bricked, thanx to XDA community for help (specially @[NUT] ) but my phone was pretty dead ...
i left my phone alone by a month and go to vacations, now im back and put my phone to wall charger.... AND ****!
i got a red light!!!!!
i know there is no hope but, the phone was very unresponsive!!! and now i have a temporal red light,
the red led, turn on and was on by 5 minutes and then off, but when i press power button the led flashes acouple of times and off,
i put the phone on a pc, and the les turns on, but i still cant get flashmode work... i was triying on pc even with custom drivers by @[NUT] but no luck
the phone still doesnt get flashmode on. the phone on pc keep showing it as a qualcom **** device or somethig so.
Now, im a mac user, and ohhhh surprise! on mac the device get 2 different status...
1 - when connect to a mac and press the power button it says :
Sony Ericcsson Mobile Communications AB
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
2- When try to get flash mode on it shows:
0x05c6 (Qualcom, Inc)
Unfortunately my flashtool on mac start to fail and i cant run it .. ( force close ?) ill try to reinstall the app
if you know how to help me on this new plataform or on a pc THNX guys!!!
if you have suggestions or tricks to try this XZ back to life it would be very appreciate!
Sorry for my english ....and thanx guys!

Try to contact @the_laser, who made the Z1 hardbrick recovery software: http://forum.xda-developers.com/showthread.php?t=2646405
As long as it's only your bootloader which has been screwed up, you will have every chance he might be able to fix it.

Related

[Guide] How to update/change the ROM

Modified from my instructions posted in the wiki.
http://forum.xda-developers.com/wiki/index.php?title=Samsung_Omnia_7#Updating.2FChanging_the_ROM
Updating/Changing the ROM
Before continuing with any of the following processes, you should note that (at present) there is no way to back up your user data. Things such as your contacts and emails can be re-downloaded from your phone since they are stored on remote servers. Multimedia items which have been synced with Zune to your PC can also manually be transferred back to your phone. However, things such as personalisation settings, SMS and MMS are lost. Programs can, of course, be re-downloaded from the Marktetplace - but this, again, is a manual process.
This process may also help your recover a "bricked"device - or rather one which does not successfully boot up into Windows Phone fully.
Hard Reset / Full Format
You may wish to hard reset the phone if you are experiencing software errors which are not fixed after a soft reset (pulling the battery out) or if you wish to clear the phone (i.e. you've just bought the phone second hand or are selling the phone).
To hard Reset your Omnia 7 without booting into Windows Phone 7, you have to:
Turn off the phone.
Turn on the phone, holding the Power + Volume DOWN + Camera buttons
Hit home button (Start) twice to begin.
Update/Change the ROM
Disclaimer:You should note that this process may void your warranty! Neither I nor xda will be held responsible for any damage caused, or refusal of warranty, by following this guide.
Before you can update your ROM you'll need to see if you can access the phone's Download Mode.
Accessing Download Mode
To update your ROM software, you will need to be able to access the phone's download mode.
Turn off the phone
Turn on the phone, holding down the Power + Volume UP + Camera buttons simultaneously.
When the phone turns on, release the power button.
A yellow triangle with an exclamation mark and a "download mode” message should appear.
If you are successful in this then you can continue with the flash. If you are unable to access download mode, then your phone has a faulty(?) bootloader. Follow the instructions in this forum post.
Download your ROM and flash tools
To flash the new ROM you will need:
Your new ROM.
There are currently three ROMs available though the only difference is their locale (which you can change later in the settings). The 8700XXJK1 ## 2010 November CSC_Cetus_Europe_I8700XENJK1 can be found here. The ROM package is compressed in .rar format, the password is samfirmware.com
Edit: A nice sticky thread now exists with loads of ROMs available here
Samsung Mobile USB Drivers v5.2
Can be found here
Samsung WP7 Flash Program
Can be found here
Now we're ready to flash!
Turn off your phone and disconnect it from the PC
Unrar the downloaded ROM package and install the Samsung USB drivers
Boot the phone into download mode (or insert your jig)
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
Now connect the phone to your PC. Windows should recognise your device and install the drivers (it may check Windows Update first, you can either skip this or just let it be).
Open the WP7 flash program. If you are prompted with an md5 error, don't worry! You should see now an Active COM port (green) in the program.
Drag and drop the ROM files (all four) into the program, a small box will pop up and check the files. It will disappear.
Click start and the flash process begins!
DO NOT interrupt this process. Keep the phone and PC connected throughout. After 10-15mins the phone will reboot and you'll have your fresh new ROM.
Some things to note:
Between steps 7 and 8 everything should go automatically.
After the phone reboots for the fist time, a screen with a phone and a computer with an arrow and a red cross over the arrow will appear - this is OK!
There may be some delay between the phone asking for its new configuration settings and the flash program saying the flash is complete (a progress bar states it is still "Rebuilding"). It may be wise to just allow that progress bar to complete before inserting the new settings.
Depending upon what ROM you flash, you will find that your language and locale are probably not correct. You will need to change these in "Settings" for things such as Marketplace to work correctly.
If the Flash program does not recognise your device, try a different USB port. If that still doesn't work, try starting the program first and then plug in your phone.
Credits: Heathcliff74 and Erwan for the images.
Casey
Very good and very detailed... super job dude!
One quick question if i may... the screenshots show Vista OS i believe? Any idea if this will work on XP at all?
Thanks in advance
Yep, I think it works on Windows 2000 SP4, XP SP3, Vista and 7 - though I've only tested it on Win 7.
Let us know, if it doesn't!
Casey
i cant seem to extract the file. its failing
The updater app didn't seem to recognise the phone at first try, y had to reconnect it several times until everything went fine
Thanks, updated!
mikkybukky82 said:
i cant seem to extract the file. its failing
Click to expand...
Click to collapse
Did you enter the password? Somewhere in your rar extractor you'll have to put the password: samfirmware.com
Hope that helps,
Casey
Update successful ^^
Thanks for the guide !
Omnia 7 French locked to ORANGE
Flashing the ROM always seemed quite complicated to me. But after going thorugh the guide and flashing my phone successfully I have to say it actually quite easy.
Thanks for the guide.
Flashing is quick and easy with this guide, very n00b friendly.
I have a problem :S ...
i want to update my Omnia 7 and i get this...
I don't know why ... it was green...com 3
EDIT: I guess that i must connect USB cable to back of my PC ... in front USB just disconnecting device.
gogibyte said:
I have a problem :S ...
i want to update my Omnia 7 and i get this...
I don't know why ... it was green...com 3
[B]EDIT: [/B] I guess that i must connect USB cable to back of my PC :) ... in front USB just disconnecting device.[/QUOTE]
Yeah that's strange but I used to have the same problem when flashing ROMs to my HTC HD2, some of the USB ports worked and some didn't.
Glad you managed to fix it though!
Casey
Click to expand...
Click to collapse
Is this fw 7.0.7008?
premikkoci said:
Is this fw 7.0.7008?
Click to expand...
Click to collapse
No, but you should find that as soon as you flash this you'll get the notification to update.
Casey
I have a problem. My HP pavilion 6 doesn´t found my omnia 7 in download mode.
premikkoci said:
I have a problem. My HP pavilion 6 doesn´t found my omnia 7 in download mode.
Click to expand...
Click to collapse
You've installed the drivers, right?
If so, try using a different USB port.
Casey
premikkoci said:
I have a problem. My HP pavilion 6 doesn´t found my omnia 7 in download mode.
Click to expand...
Click to collapse
had the same issue...
- first i had to use jig for downloadmode (with the 3 button "trick" i got only the restore thing)
- i plugged the phone to computer...nothing happens (driver was installed before and i have rebooted)
- i unplugged the phone and used another usb port
-> driver where installed, i thought all is fine
- i started "WP7 flash program" but the program didnt see the phone, i checked device manager and all looked fine
- i unplugged the phone and plugged it in at the usb port i used first (when the phone was in restore mode)
- wp7 flash program found my phone
- flashed and all was fine
btw had a t-mobile (de) branded one and didnt get the 7008 update...now i have it in no time
€dith
i think marketplace and zune (on the phone) are now much more stable#
@dith 2:
marketplace ist much much much more stable compared to my original image and i had bad lags, now...no lags.
I dont know if the 7008 update makes this all or just the new firmware
EDIT. It works!
Is it possible to reverse this incase you need to return your phone for repair etc ?
Forzahibs said:
Is it possible to reverse this incase you need to return your phone for repair etc ?
Click to expand...
Click to collapse
If you can find your original ROM, then yes.
Casey
Download Mode
When I try to put my Omnia 7 into download mode using the 3 buttons I get a screen showing a phone to the left with a zig zag arrow to a laptop on the right. Is this an alternative download mode screen or is it the "bad" downloader??

[q] my galaxy pocket wont start nor can i enter recovery

HEY GUYS !!
I am new to xda so im not sure if i have posted it at the right place.
anyway, my phone (galaxy pocket GTS5300) is rooted runs on infuzion 2 kernel and has hydroperia v2 custom rom(i followed the instructions from xda)
so recently i wanted to increase its ram so i partioned my external sd and installed swapper 2 (just like the post in xda),everything went all right
then i downloaded "file2sd"" from play store and installed it to gets some space in my phones internal memory but as i opened the app and selected
the format as ext3 the said i have to reboot and i pressed the "" restart now ""button,thats it and the phone just got stuck i waited for some time no buttons responded so removed the battery and tried turning it on but it just shows a blank screen after showing the model no. and i CANT enter recovery mode but i can enter odin (but my laptop does not recognize the device,eventhough i have tried installing all the usb drivers and kies ,i dont know if its because of the data cable or windows8 or my phone ) so i removed my external sd copied all my files and saw (in mini tool partition wizard)that my 2nd partition was full(512 mb)i didnt know what to do and i formatted everything(sd).
i dont know what to do next .someone please help!!!
glenzac said:
HEY GUYS !!
I am new to xda so im not sure if i have posted it at the right place.
anyway, my phone (galaxy pocket GTS5300) is rooted runs on infuzion 2 kernel and has hydroperia v2 custom rom(i followed the instructions from xda)
so recently i wanted to increase its ram so i partioned my external sd and installed swapper 2 (just like the post in xda),everything went all right
then i downloaded "file2sd"" from play store and installed it to gets some space in my phones internal memory but as i opened the app and selected
the format as ext3 the said i have to reboot and i pressed the "" restart now ""button,thats it and the phone just got stuck i waited for some time no buttons responded so removed the battery and tried turning it on but it just shows a blank screen after showing the model no. and i CANT enter recovery mode but i can enter odin (but my laptop does not recognize the device,eventhough i have tried installing all the usb drivers and kies ,i dont know if its because of the data cable or windows8 or my phone ) so i removed my external sd copied all my files and saw (in mini tool partition wizard)that my 2nd partition was full(512 mb)i didnt know what to do and i formatted everything(sd).
i dont know what to do next .someone please help!!!
Click to expand...
Click to collapse
So you can actually enter the "download" mode. Thats good at least.
Win 8 comatible driver --> Samsung 1.5.27.0
Which version of odin do you use? This will wotk for you --> Odin 3.07
thanks 4 quick reply
THANKS FOR THE REPLY!!!!!
I HAVE THE USB DRIVER 1.5.23 and still the phone wont work.
actually i have both odin1.85 and 3.09
glenzac said:
THANKS FOR THE REPLY!!!!!
I HAVE THE USB DRIVER 1.5.23 and still the phone wont work.
actually i have both odin1.85 and 3.09
Click to expand...
Click to collapse
Check under device manager if it shows usb device with yellow triangle while phone is connected to computer (Be sure to set show all devices)
yes
LS.xD said:
Check under device manager if it shows usb device with yellow triangle while phone is connected to computer (Be sure to set show all devices)
Click to expand...
Click to collapse
when i used to connect the phone it would show "usb device not recognized".i tried reinstalling the usb drivers but no use.
glenzac said:
when i used to connect the phone it would show "usb device not recognized".i tried reinstalling the usb drivers but no use.
Click to expand...
Click to collapse
you have to force the installation. Right mouse on device. Install driver. select driver manually. (you have to xtract the driver files from the installer first) show "incompatible" devices --> musg be sth like "USB composite device"
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
k
LS.xD said:
you have to force the installation. Right mouse on device. Install driver. select driver manually. (you have to xtract the driver files from the installer first) show "incompatible" devices --> musg be sth like "USB composite device"
Click to expand...
Click to collapse
im sorry i havent understood what you said, can you PLEASE explain it in a detailed manner
glenzac said:
im sorry i havent understood what you said, can you PLEASE explain it in a detailed manner
Click to expand...
Click to collapse
device manager shoes "unknown device" with a yellow triangle?
glenzac said:
HEY GUYS !!
I am new to xda so im not sure if i have posted it at the right place.
anyway, my phone (galaxy pocket GTS5300) is rooted runs on infuzion 2 kernel and has hydroperia v2 custom rom(i followed the instructions from xda)
so recently i wanted to increase its ram so i partioned my external sd and installed swapper 2 (just like the post in xda),everything went all right
then i downloaded "file2sd"" from play store and installed it to gets some space in my phones internal memory but as i opened the app and selected
the format as ext3 the said i have to reboot and i pressed the "" restart now ""button,thats it and the phone just got stuck i waited for some time no buttons responded so removed the battery and tried turning it on but it just shows a blank screen after showing the model no. and i CANT enter recovery mode but i can enter odin (but my laptop does not recognize the device,eventhough i have tried installing all the usb drivers and kies ,i dont know if its because of the data cable or windows8 or my phone ) so i removed my external sd copied all my files and saw (in mini tool partition wizard)that my 2nd partition was full(512 mb)i didnt know what to do and i formatted everything(sd).
i dont know what to do next .someone please help!!!
Click to expand...
Click to collapse
The Best Solution Is :
Press thanks if It helps
Download CWM From here : http://forum.xda-developers.com/attachment.php?attachmentid=1461120&d=1352197095
Download Stockrom from here : http://www.4shared.com/zip/SZzB-egN/S5300XXLF5_S5300BTULF1_BTU.html
Put both zips in your sd card
go to recovery mode by pressing vol up + home button + power button (Hold for 10 seconds)
Now in recovery mode select apply update from sd card and select cwm file...
Now in cwm mode again go to apply update from sd card ...
Select Stock ROm ZIP...
You will now boot normally
N'ayam Amarsh'e said:
Download The Samsung Unbicking Software from Here http://forum.xda-developers.com/showthread.php?t=1153310 and try it out and if it works press thanks button and also of the creator of this software....
Click to expand...
Click to collapse
Have you tried this before? I did --> no success at all, its made for Galaxy S. Sure try it out
PM me if ya want something-...
further?
LS.xD said:
device manager shoes "unknown device" with a yellow triangle?
Click to expand...
Click to collapse
ok i am working on it
if at all it works what am i to do next?
what all files should i have?
LS.xD said:
Have you tried this before? I did --> no success at all, its made for Galaxy S. Sure try it out
PM me if ya want something-...
Click to expand...
Click to collapse
It's edited now....
glenzac said:
ok i am working on it
if at all it works what am i to do next?
what all files should i have?
Click to expand...
Click to collapse
you have extracted samsung drivers in a folder on your desktop????
right mouse button on unknown device - install driver - searh pc for drivers -> show list -> select folder where the samsung driver is stored -> unmark "compatible devices" and then you can manually select a device if it shoes not compatible -> ignore just install
before we fill 20 more pages may be you can install "gtalk"?
what next???
N'ayam Amarsh'e said:
It's edited now....
Click to expand...
Click to collapse
the soft brick software will not do as i can access odin
so can someone please help me to go ahead with odin
what files would i require?
also there is another major problem my phone wont charge.the second i connect the charger the phone tries to turn on and returns back to the black screen,
please help
glenzac said:
the soft brick software will not do as i can access odin
so can someone please help me to go ahead with odin
what files would i require?
also there is another major problem my phone wont charge.the second i connect the charger the phone tries to turn on and returns back to the black screen,
please help
Click to expand...
Click to collapse
MAN did you installed driver as i said? when its showing Samsung USB comosite device --> flash stock rom with odin. S5300 Stock firmwares make sure to have your region
Your phone has to b connected in "download" mode (by pressing the 3 button combo)
If you cant enter download mode? release battery and connect phone to pc with usb cable then press Vol- and home and power and put back in battery while. Your computer should get the device.
you flash stockrom using odin.
Sry for that complicated chat, but its not that easy using a browser based chat for that. Also you got more then 1 person tell what to do. Seems not workin that good...
So if something is still not cleat, may be install GTalk for easier chat or teamviewer that i can "show" what i mean.
regards
no luck
LS.xD said:
MAN did you installed driver as i said? when its showing Samsung USB comosite device --> flash stock rom with odin. S5300 Stock firmwares make sure to have your region
Your phone has to b connected in "download" mode (by pressing the 3 button combo)
If you cant enter download mode? release battery and connect phone to pc with usb cable then press Vol- and home and power and put back in battery while. Your computer should get the device.
you flash stockrom using odin.
Sry for that complicated chat, but its not that easy using a browser based chat for that. Also you got more then 1 person tell what to do. Seems not workin that good...
So if something is still not cleat, may be install GTalk for easier chat or teamviewer that i can "show" what i mean.
regards
Click to expand...
Click to collapse
sorry for responding late i tried all that you said but no luck.
i am beginning to suspect it is the problem of the cable or of the phones jack
Hey ,
Just install Kies and uninstall that USB driver . Download files exept .pit and try again . If boot is force closing , go to recovory mode . It should work . Worked in my case
Sent from my GT-S5300 using xda app-developers app
sorry everyone for the late reply
I had gone on a long trip on my way back I also bought an USB cable then it worked perfect ,and I flashed stock Rom with Odin. Alright
Thanks
Now I have a new query can I upgrade my galaxy pocket to jelly bean.
Please help

USB didnt work only for chargeing

Hi guys ,
i have problem with my xperia Z. comes troubles with USB connection.
especially with data transfer , it didn't connect to the flashtool and also did not works Fastboot and flashmode.
I tried many cables and so many ways to repair it. but it didn't help.
factory reset didn't help and also repair with PC companion, i tried change MTP and MSC mods but it didnt help also,
do someone of you know what to do? or what to do to flash clear sony rom to complaint it at the store where i bought my phone,??
thank u very much for any help!!
:crying::fingers-crossed:
Hi, have you flashed a Custom ROM before the USB problem appeared?
You wrote about trying to fix with Sony PC Companion, but how it's possible if the USB connection of your phone doesn't work?
Let me know clearly the situation, you cannot transfer any data through USB?
If you cannot transfer data through USB and the problem appeared suddenly , can be an hardware issue with USB Connector.
Are you on STOCK or CUSTOM ROM?
Have you tried to wipe cache/factory from recovery to see if that helps?
If you want more help let me know more details
paranormal11 said:
Hi, have you flashed a Custom ROM before the USB problem appeared?
You wrote about trying to fix with Sony PC Companion, but how it's possible if the USB connection of your phone doesn't work?
Let me know clearly the situation, you cannot transfer any data through USB?
If you cannot transfer data through USB and the problem appeared suddenly , can be an hardware issue with USB Connector.
Are you on STOCK or CUSTOM ROM?
Have you tried to wipe cache/factory from recovery to see if that helps?
If you want more help let me know more details
Click to expand...
Click to collapse
Hi, yes I flash custom rom before USB goes wrong..
I mean it with PC companion , that i tried it and it didn't work..it means that i stuck on the part when u have to connect phone with volume down.
Yes, i cannot transfer the data through USB, i cannot nothing with USB flashmode, Fastboot. only thing i can do is charging with charger.
I tried to flash clear , Stock rom 5.0.2 , but I thing that it have little customization...
Yes, i tried to wipe but only from service menu and settings of phone.. because my recovery disappear...somehow
Thank you for your hapls!!!!
It's a really strange thing,
You have wrote tried to flash Android 5.0.2 is flashing process going fine?
Can you confim that when Sony PC Companion ask for the phone, the phone is off and you connect to USB holding e keeping press Volume -
You have to press and hold Volume - before connect USB cable to PC.
Wich CUSTOM ROM have you flashed before USB goes wrong? Have you use the recovery or flash with Flashtool?
The USB connector with the CUSTOM ROM installed have never works?
Are you sure you have not broken your USB connector?
Let me know
paranormal11 said:
It's a really strange thing,
You have wrote tried to flash Android 5.0.2 is flashing process going fine?
Can you confim that when Sony PC Companion ask for the phone, the phone is off and you connect to USB holding e keeping press Volume -
You have to press and hold Volume - before connect USB cable to PC.
Wich CUSTOM ROM have you flashed before USB goes wrong? Have you use the recovery or flash with Flashtool?
The USB connector with the CUSTOM ROM installed have never works?
Are you sure you have not broken your USB connector?
Let me know
Click to expand...
Click to collapse
.. I flash the rom before month? or so.... and then after month normal working transfer data via USB and pc and charging from pc ..I want to backup my data (photos , videos etc..) and it didnt works...so i tried many ways to repair it or get works.. ( as i says up))
yes ofcourse I know that phome must be switchoff before geting to flashmode..
The usb connector works normally whit milions rom i tried before..)
may be it is broken,, so now im trying to remove/delete kingroot and find out which rom I flash (this..the last one)
THX mate )))
If the USB connector worked for some time with the CUSTOM ROM installed, i think it isn't a ROM problem, can be an app that caused this but probably may be an hardware problem of the USB connector.
If you have already wiped all your data and reset your phone to factory settings and the problem persist, at 99,9% it's a fault USB connector.
paranormal11 said:
If the USB connector worked for some time with the CUSTOM ROM installed, i think it isn't a ROM problem, can be an app that caused this but probably may be an hardware problem of the USB connector.
If you have already wiped all your data and reset your phone to factory settings and the problem persist, at 99,9% it's a fault USB connector.
Click to expand...
Click to collapse
usb works before.. and now it is broken for two weeks.. so it looks like usb connector is broken..
so.. can u help me with removing the king root ( and kinguser app) pls?? because if i tap in the settings of Kinguser app ´´remove root permission´´ and than clear.. its processing.. but afer that is kinguser still there.....
what shall i do?
Have you tried different cables?
Perhaps one of the wires is torn.
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
There are cables for data transfer & there are cables for power supply.
of course.. I tried.. as I says before in the first post .(maybe four different cables)
i'm trying to remove root and then try to complain the phone.. but in not sure which one of rom i have now.. I cant recognize if it is stock rom or not.. and I can't remember which I flashed this last one...:/
Your ROM Version is a Stock Android 5.0.2 for UK (United Kingdom) phones
http://forum.xda-developers.com/xperia-z/general/stock-rom-xperia-z-c6603-10-6-0-454-t3127499
" Xperia Z (C6603) Generic UK (.FTF)"
Android version: 5.0.2
Baseband: 9x15A-ACEFWMAZQ-30110212-82
Kernel: 3.4.0-perf-g8fa3dae [email protected] #1 Wed Apr 8 17:43:10 2015
Build number: 10.6.A.0.454
Customization Version: 1270-7689
Branding: Generic UK
Country: United Kingdom
BUT
kingvortex said:
This works on ANY Xperia Z (C6603).
Click to expand...
Click to collapse
So this is not the reason for your problem.
Did you wipe your Cache/Dalvik Cache with recovery?
If not...do it and try again.
You could activate the Development Settings in Android
1. Go to settings
2. Choose "about the phone"
3. Press 5 times on "Build Number" till the message "your are a developer"
4. go back
5. go to Developer-options (it's a new setting directly over the point "over the phone")
6 Activate "USB-Debugging" or "Android-Debugging"
7. Try again to connect with PC.
Good luck
If you connect to PC....
What shows your PC?
1. Look for new Partitionen.
2. Look into Printer & Devices
3. Look into Device-Manager (ne USB Device? Or Modem Device? Or something else?)
4. Look into Partitiontables on your PC.
thx...
BUT there is the problem.... My recvery disepeared...
SO.. is it possible to install recovery without PC?? I have Unlock Bootloader and root.. what about using the emulator.. MUST BE ANY WAY to get RECOVERY without PC just installed in phone..PLS help
Sure you can install recovery without pc:
(but only with root)
1. Download https://dl.twrp.me/yuga/twrp-2.8.7.0-yuga.img.html
2. Copy file to external SDCard
3. Install Shell-App (Terminal) on Phone (f.e https://play.google.com/store/apps/details?id=com.acr.shellterminalemulator or https://play.google.com/store/apps/details?id=jackpal.androidterm)
4. open shell/terminal
5. Type "su" without ""
6. Type "dd if=/sdcard/twrp.img of=/dev/block/platform/msm_sdcc.1/by-name/FOTAKernel" without ""
if it dosn't work (but should work) try following:
http://www.jmzsoftware.com/downloads/TWRPManager.apk (direct download) or https://play.google.com/store/apps/details?id=com.jmz.soft.twrpmanager (play store but same file)
or
http://dl.cdn.chip.de/downloads/112...434-bd44ef-B-80f5410908912da7c9de22a0ec003aed
or
https://play.google.com/store/apps/details?id=de.mkrtchyan.recoverytools
Good luck
THX.. @Xperience Z
that apps i tried before..)
but also the command didnt work...
i wrote..
su
dd if=/sdcard/twrp-2.8.7.0-yuga.img of=/dev/block/platform/msm_sdcc.1/by-name/FOTAKernel
(is it right? )
(i renamed twrp-2.8.7.0-yuga.img to twrp.img because short is good )
so...you should use "supersu" instead of Android own adminprogram......
if you type su, the terminal will ask you "Terminal tries to get root access"
did you copy the twrp.img on internal or external sdcard?
There are several ways to Rome.
internal:
dd if=/sdcard/twrp.img of=/dev/block/platform/msm_sdcc.1/by-name/FOTAKernel
dd if=/storage/sdcard0/twrp.img of=/dev/block/platform/msm_sdcc.1/by-name/FOTAKernel
dd if=/mnt/sdcard/twrp.img of=/dev/block/platform/msm_sdcc.1/by-name/FOTAKernel
external:
dd if=/storage/sdcard1/twrp.img of=/dev/block/platform/msm_sdcc.1/by-name/FOTAKernel
dd if=/ext_card/twrp.img of=/dev/block/platform/msm_sdcc.1/by-name/FOTAKernel <- that's what i use
Here you've Screenshot How-To:
Rashr from play store is another option. Select the. img and flash it to recovery (in reality - fotakernel)
Good Luck again
@Xperience Z
THANXX!!
but nothing helps.....i dont know why..
also rash didnt works..
SO I will unroot my phone and make factory reset form setting and i have to hope that they will accept my complaint and repair my phone..
what will u recommend me to real unroot (deleting the su user (kingroot and kinguser in my case) ??
thx so much mate!
Did you activate "USB Debugging" ?
Dude you have a problem.
unroot = revert to stock (flash stock rom) - there is no other method.
But by root you don't lose your guarantee / manufacturer's guarantee.. Only by unlocking the bootloader.
what will you get for messages in terminal?
can you make screenshots?
You could try super-sume https://play.google.com/store/apps/details?id=darkslide.com.supersumepro
(for a few dollars)
Then when kingroot has been purged and replaced with supersu, you can do a full unroot from within the supersu app.
The unlocked bootloader may be the bigger problem though. It can, in some cases void warranty repair. (depending on seller/repairers attitude )

[GUIDE]How unbrick your L5 from a softbrick

After my friends ask me so much for me to do this tutorial for the sake of L5, I decide to do.
If you see your L5 does not start the system, it is the LG logo, follow a tutorial below according to your case.
Note that this guide helps only in cases of softbrick. In cases of hardbrick, I recommend you go to a technical assistance.
If your device is in the boot animation forever:
Probably you should have modified the system and is very easy to recover. Just look for the ROM that you were using normally occur before it and reinstall.
If your device is not out of the LG logo and/or not go to recovery:
1 - Download the drivers here and install: http://depositfiles.org/files/8nbpilxsh
2 - Download the stock ROM here: http://lg-phone-firmware.com/index.php?id_mod=12
Download according to your device!
3 - Go to the download mode.
If the baseband is V10, remove the battery and insert it again (don’t turn it on!). Press and hold volume up button and volume down buttons and connect the device to your computer while holding the buttons.
If the baseband is V20, remove the battery and insert it again (don’t turn it on!). Press and hold volume down an connect the device to your computer while holding the buttons.
If it was not for the recovery, the stronger hold buttons! Worked with me
4 - Download the KDZ updater here http://www.unclenet.de/files/KDZ_FW_UPD_EN.7z
The file contains msxml.msi. Install it first before running the KDZ updater
5 - Start the program.
Leave the options as follows:
Type: 3GQCT
Phone Mode: DIAG
KDZ file: navigate to the file location. KDZ downloaded in step 2 and select.
6 - Click on "launch software update".
The process will take a while. No way, do not disconnect the device from your computer!!!
7 - If still not start, go to the recovery and format
To go to the recovery, will depend on the installed ROM. Each ROM is different. I do not know how to enter the recovery of all ROMs.
When you go to the stock recovery, will automatically format.
(Special case) If your screen looks like this:
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
Do as if you were standing in the logo of LG. However, in this case, will not appear on the screen written this in download mode.
To go in download mode, you will have to have plenty of patience to get out of this situation.
Try:
Hold the volume up and connect the PC;
Hold the volume down and connect the PC;
Hold the volume down and up at the same time and connect to PC.
You should try one of these at a time and wait about 10 seconds. While the screen does not look like this, keep trying and holding the stronger buttons.
View attachment 3726726
Make sure it is connected. Go on the control panel, Hardware and Sound, Devices and Printers. If not appear, uninstall the drivers in the device manager and reinstall it.
After that, you just have to install the ROM on KDZ updater.
its a softbrick when it comes and its easy thats right,but whats when we have a real hardbrick?
--SIGNATURE--
-CALIBAN666- said:
its a softbrick when it comes and its easy thats right,but whats when we have a real hardbrick?
--SIGNATURE--
Click to expand...
Click to collapse
I don't know
Amazing man, I appreciate your work
Jonas Cardoso said:
Amazing man, I appreciate your work
Click to expand...
Click to collapse
thanks
Hard brick is when your device won't react to any of your actions.
n0b0dy666 said:
Hard brick is when your device won't react to any of your actions.
Click to expand...
Click to collapse
So all I said is to recover from a soft brick?
Antonio Almeida Filho said:
So all I said is to recover from a soft brick?
Click to expand...
Click to collapse
Yes.
Soft brick; bootloop etc.
Hard brick; phone wont turn on & can not access recovery/download mode.
rhystagram said:
Yes.
Soft brick; bootloop etc.
Hard brick; phone wont turn on & can not access recovery/download mode.
Click to expand...
Click to collapse
Therefore, I have nothing to say about hardbrick. In this case, I would recommend just taking the phone into a technical assistance.
Antonio Almeida Filho said:
Therefore, I have nothing to say about hardbrick. In this case, I would recommend just taking the phone into a technical assistance.
Click to expand...
Click to collapse
Btw... How did this thread ended in XDA Home Page??:silly:
Hardbrick is relatively easy too (just one temporary pull down on eMMC data line, then emergency downloader from SoC is available over usb), though for writing guide/testing software i would need actual genuine hardbrick (mobo of l7 or enough of l5)
But even if i write guide, you will still need to have full eMMC backup, any other way while not impossible, violates xda rules. Otherwise you will have no IMEI (though that state could be still useful)
Unfortunately this sock doesn't support QDL 9008 from what I know. The title is just misleading. There is no hard-brick here.
It does since forever:
MSM7k ARMv7 - over USB
any before - over UART
Guys, I never said that this tutorial is about hardbrick. You probably should have seen it http://www.xda-developers.com/xda-external-link/unbrick-lg-optimus-l5-from-hard-brick/ . I think you should discuss it there, with the guy who spoke that it is a hardbrick guide.
neutrondev said:
Unfortunately this sock doesn't support QDL 9008 from what I know. The title is just misleading. There is no hard-brick here.
Click to expand...
Click to collapse
I DO NOT told at any time that was hardbrick. I'm going for the title which is softbrick. This so good?!
Antonio Almeida Filho said:
I DO NOT told at any time that was hardbrick. I'm going for the title which is softbrick. This so good?!
Click to expand...
Click to collapse
True. My bad mate.
Antonio Almeida Filho said:
Guys, I never said that this tutorial is about hardbrick. You probably should have seen it http://www.xda-developers.com/xda-external-link/unbrick-lg-optimus-l5-from-hard-brick/ . I think you should discuss it there, with the guy who spoke that it is a hardbrick guide.
Click to expand...
Click to collapse
Apologies for the inconvenience caused. I should try and work with more coffee. It was not my intention to cause such harm. The post has been removed.
a.cid said:
Apologies for the inconvenience caused. I should try and work with more coffee. It was not my intention to cause such harm. The post has been removed.
Click to expand...
Click to collapse
Do not get this message as irony, but thank you for that.
LG E 610 Softbrick tried everything MPT Driver fails to load
hi,
i have an LG Optimus L5 (LG-E610) here, it used to have a Stock Android 4.0.3 of nov 06-2012 on it and i tried to put a custom 4.4.4 ROM on it. i had root, Philz Recovery installed and flashed with it: 20 baseband, ROM, gapps, in that order. after it was finished-> reboot system. but the fon would not boot properly and show my a dizzy screeen. after i installed LGMobileDriver_WHQL_Ver_4.2.0.exe and tried flashing V10B_00.kdz with the KDZ_FW_UPD_EN.7z tool. ti said "phone not found" no matter in wich way i used it. after this the fon would not be properly recognised by the win7 x64 pc anymore. the "Android Net MTP device" driver fails to install. some mpt driver used to work before.
after this i also worked with the lg mobile tool und the lg 3.8 mobile driver. uninstalled drivers, used other pcs, virtual oss, lg pc suite. i tried every possible combination of push buttons (i believe) and did with and without battery in the fon. the problem remains. MTP device driver fails to install.
WHAT TO DO?
i have an old device, i cant access the download mode or recovery mode just a white screen, this happen after i was trying to flash a custom recovery (twrp). any have an idea? i just need to enter the download mode, and the kdz wont recognize the device

[HELP] Phone is stuck at Linux Penguin Logo ( Bootloader, Recovery Not Responding)

Good Morning Guys,
I have Redmi 4X 64GB version. The phone has unlocked bootloader and was running on Havoc OS V2.5 and the phone was rooted.
About a week ago the phone is suddenly got into weird state. And i am unable to figure out what to do.
The phone is gotten into Linux Penguin Logo. I am attaching an image with that problem. And also phone in not responding to any physical power+volume button integration. Any combination just takes me to this Penguin Screen. Here are some thing i have already tried to do but not working at all. Although when i connect this device to computer with this Penguin Logo screen it does get detected as fastboot device but so far that isn't helping.
Some tricks that i have already tried but not working:-
1. I have booted my phone into edl mode and installed fastboot rom via miflash tool, and it is successfully installed but after pressing power+volume button it is the same screen as Penguin Logo. [so Not Working]
2. I have opened the phone disconnect the battery and tried some combinations but still no luck.
3. Used every combination with power button as well as connected to pc and used fastboot commands but not working out.
4. TWRP installation get failed. ( will attach the preview).
So, Please anyone has any clue or anyone has ever face this same problem please reach out to me. Any Honect answer will work.
Sorry i am new at writing thread. So if any mistake i am sorry.
Images:
If you still have custom recovery installed then try flashing latest firmware.
i've found this similar having issue video on youtube of Redmi 3S(Appears to be) and how it got solved, please check it here https://www.youtube.com/watch?v=oMZ08qQrqnc
i am not sure if those files are limited to Redmi 3S or can be use on other xiaomi devices but it gives some sort of idea what you should try. and video language i don't understand and maybe you understand maybe not but should be understandable by watching video.
Thanks for replying. But that is the problem i am unable to reach anywhere not bootloader nor recovery. The phone is just showing the linux penguin logo whether you use power and volume combination or you do the same via connecting to pc.
I think he has that download link in description. But that link requires password for opening .rar file. And i do not trust that guy. That file may have some bloatware or virus or something. If you find same file that he has please share that file over here so that i can use it.
Thanks.
SafvanShaikh said:
I think he has that download link in description. But that link requires password for opening .rar file. And i do not trust that guy. That file may have some bloatware or virus or something. If you find same file that he has please share that file over here so that i can use it.
Thanks.
Click to expand...
Click to collapse
Did you solve the problem? I'm stuck in it and after trying all the things (including deciphering that rar file very doubtful, which I did not achieve) I'm empty of ideas
try to put the phone in edl mode...open the phone case and disconnect the battery wire..if u have tweezer then try touching it to testpoints and then plug the usb cable at the same time...a driver will install on ur computer named (qdloader9008)....open miflash tool then try flashing it via the tool...
Time to use Device as Paper Weight
::
victorkorp1999 said:
Did you solve the problem? I'm stuck in it and after trying all the things (including deciphering that rar file very doubtful, which I did not achieve) I'm empty of ideas
Click to expand...
Click to collapse
Sorry Bro, Nothing is working at all. I mean i am IT Engineer and i have tried all things but still no luck. So, my thinking is the boot loader is too much damaged so there is nothing that can be written on it, no TWRP or no any data partition, it's all out of option. I have started using the phone as Paper Weight.
I am still hoping that someone can solve this problem and get back to me. Fingers Crossed
Thank You.
Not Working, Already tried:
jerry.07 said:
try to put the phone in edl mode...open the phone case and disconnect the battery wire..if u have tweezer then try touching it to testpoints and then plug the usb cable at the same time...a driver will install on ur computer named (qdloader9008)....open miflash tool then try flashing it via the tool...
Click to expand...
Click to collapse
Sorry Bros, Already tried all things that you have mentioned in the post and its not working at all. If somehow we can change the memory storage chip on the phone that contains the bootloader then the phone can come back to its normal form.
Try to turn fastboot if you turn this on then you are on good situation . Boot TWRP and try installing rom again ( with wiping data, cache,vendor,system,dalvik,and might internal storage)
Your problem solved or still u r stuck?
To answer your question, yeah i got it done. Actually where i live, there is repair shop guy that i know he got it done for just 500rs. I don't know how he do that.
Here is my own tested solution for you !
In my case, when i try to install boot logo on Redmi 5 then this happened.
And yet last . i find the great solution by Miassistant
.1. Download Miassistant on PC
2. Download ADB Driver for your Pc
3. Download (Recovery Rom) not Fastboot Rom
5. press volume up + Power for (Miassistant mode)
6. Flash from Miassistant
Thanks for the solution. My device is already fixed, but i this solution can work. If something like this happens in future we can try this out. But i really wanna know what causes this thing to be happened?
Xiaomi Mi 5s Plus stuck in Linux icon FIXED
SafvanShaikh said:
Thanks for the solution. My device is already fixed, but i this solution can work. If something like this happens in future we can try this out. But i really wanna know what causes this thing to be happened?
Click to expand...
Click to collapse
Sorry if this is not the place for post this, but I read a lot of cases that people have their phones stuck in Linux Icon, after a fail installing a ROM, this same case happened to me in a Xiaomi Mi 5 S Plus, one of the devices of Xiaomi, with less support because there were not to much units manufactered.
In mi case, after try to put the device in the fastboot mode, that was impossible I had to put the MI5 s Plus in EDL mode, using the 2 test points pins in the motherboard, and using Miflash for instal a fastboot rom.
I ll explain the steps;
A- Install MiFlash, in your computer, with all the drivers
B-Download a stable Fastboot ROM for your device, you can find it easily in the forums. ( In my case was the "natrium_global_images_V10.2.4.0.OBGMIXM_20190424.0000.00_8.0_global_07f157530a" with MIUI 10 for the Xiaomi MI5 S Plus (natrium) )
C- Put your device in EDL mode
Normally if you are stuck in the linux mode, this is your only solution for put the device in EDL mode, use the 2 test points in the motherboard of the phone.
Check in internet, where are located the test pins in your device, is different for every model. ( I attached a image of the 2 test points in Mi 5 S Plus)
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
For put the device in EDL mode:
1- Disassemble the back cover of your phone
2- Disconect the battery
3- Connect the usb cable to the phone, but not connect yet to the computer
4-Use something metallic, like a clip, wire, or tweezers, and touch the 2 Test points at the same time in the motherboard and while you re touching this 2 points connect the USB to the computer
5-You ll hear the sound in the computer that recognizes a new device conected, after that you can remove the clip or wire from touching the 2 points in the board of the phone
6-Open Miflash and have to appear a device connected like COM...., If don´t appear , you can make the process again (there is no problem if you make the steps with the MIflash open)
7- Select the option Flash all (clean all) in Miflash for install the fastboot rom
8- If some error appears during the installation, check the fastboot rom, I ll try 2 or 3 differents versions before one that was completely installed without error
9- If the installation is correct, your phone will be restart, and take some minutes for the first boot after the installation.
In my case, with this device and other Xiaomi devices, to put the phone in EDL mode, and install a stable official fastboot rom, was the only solution for this kind of software problems, I hope this post help someone
bro i have the same problem i need get my data how can i get back please help i have my grandmother lst pics in it
SafvanShaikh said:
To answer your question, yeah i got it done. Actually where i live, there is repair shop guy that i know he got it done for just 500rs. I don't know how he do that.
Click to expand...
Click to collapse
bro data recover hoaa ke nahi please tell me
SafvanShaikh said:
To answer your question, yeah i got it done. Actually where i live, there is repair shop guy that i know he got it done for just 500rs. I don't know how he do that.
Click to expand...
Click to collapse
without data loss..., please fast reply given my redmi 3s prime mobile this type problem I attached charging and show bird logo no any start... please contact me 9106142185

Categories

Resources