[Q] stuck on Odin - Galaxy Note GT-N7000 Q&A, Help & Troubleshooting

HI, i m update my N7000 to 4.1.2 , when i was use Odin it stuck on status below
<ID:0/016> Odin v.3 engine (ID:16)..
<ID:0/016> File analysis..
<ID:0/016> SetupConnection..
<ID:0/016> Initialzation..
<ID:0/016> Get PIT for mapping..
<ID:0/016> Firmware update start..
<ID:0/016> boot.bin
<ID:0/016> NAND Write Start!!
and also can turn to recovery mode.
ps help

Try to flash a rom zip file from recovery.

nokiamodeln91 said:
Try to flash a rom zip file from recovery.
Click to expand...
Click to collapse
Can not turn in recovery mode

First post you wrote you CAN. Anyways how did you reach this situation?

nokiamodeln91 said:
First post you wrote you CAN. Anyways how did you reach this situation?
Click to expand...
Click to collapse
Sorry , can not turn to recovery mode, just can turn to download mode ( Odin can ) , but when update to ( N7000DXLSE_N7000OLBLSE_N7000DXLS8 ) it stuck at below
<ID:0/016> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> N7000DXLSE_N7000OLBLSE_N7000DXLS8_HOME.TAR.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/016> Odin v.3 engine (ID:16)..
<ID:0/016> File analysis..
<ID:0/016> SetupConnection..
<ID:0/016> Initialzation..
<ID:0/016> Get PIT for mapping..
<ID:0/016> Firmware update start..
<ID:0/016> zImage
<ID:0/016> NAND Write Start!!
Ps help what can i do next

Start by telling us what did you do to reach that situation.

Related

help miui to stock

help miui to stock
Installed miui MGCv3 to try out which I liked very much but no FM radio so I Went back2 fyoro using Ezbase 2 but I get Fail on
<OSM> Leave CS..
<ID:0/009> Odin v.3 engine (ID:9)..
<ID:0/009> File analysis..
<ID:0/009> SetupConnection..
<ID:0/009> Initialzation..
<ID:0/009> Set PIT file..
<ID:0/009> DO NOT TURN OFF TARGET!!
<ID:0/009> Get PIT for mapping..
<ID:0/009> Firmware update start..
<ID:0/009> boot.bin
<ID:0/009> cache.rfs
<ID:0/009> factoryfs.rfs
Click to expand...
Click to collapse
can get into download mode with 3 button and resistor 301k
Have you tried re-downloading all the EZbase files including the EZodin and EZpit, could be a corrupt file(maybe the pit)
I've not had a problem reverting back to the 2.2.1 EZBase firmware. I did get a lot of errors when trying to install the 2.3.3 version of EZBase though. Just make sure that you use the pit file that is in that thread and you should be good to go.
As far as the radio issue in MIUI goes, there are plenty of 3rd party fm radio apps on the market that you can use to get the radio feature back again.
Re download all the files but still no joy
<ID:0/009> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> EZbase-PDA-XWJS3.tar.md5 is valid.
<OSM> EZbase-PHONE-XXJVE.tar.md5 is valid.
<OSM> EZbase-CSC-XXJV1.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/009> Odin v.3 engine (ID:9)..
<ID:0/009> File analysis..
<ID:0/009> SetupConnection..
<ID:0/009> Initialzation..
<ID:0/009> Set PIT file..
<ID:0/009> DO NOT TURN OFF TARGET!!
<ID:0/009> Get PIT for mapping..
<ID:0/009> Firmware update start..
<ID:0/009> boot.bin
<ID:0/009> factoryfs.rfs
Click to expand...
Click to collapse
Ive had this problem. Wipe all data/factory reset from the recovery menu and then download a new firmware from www(.)samfirmware(.)com
Flash one which has 3 files, not the one which gives you one file which you enter into pda cause you cant select repartition

[Q] Help Required - Camera stuck in Download Mode

Hi all,
Before I return this device back to Samsung i wanted to check here if anyone had similar Problems or can possibly help with this.
I've never had the Luxury of personally using this Device, the Original Owner bought it and during the OTA it appears something went wrong. Rather than returning it to Samsung directly (they have a notoriously bad reputation of turn around time here) she asked me to have a look at it
Originally it was stuck in a Bootloop of The Intro of the boy looking through the telescope and appearing with the Samsung logo in a recurring Bootloop. Kies (the terrible software it is) is stuck at the connecting screen and doesn't move further than that.
To the jist;
I cant enter Recovery Mode, it takes me directly to the "downloading" screen. I can however boot manually into the Downloading mode. I've tried reflashing the stock recovery with Odin but still won't allow me to get into it, it boots to download mode before I even get a chance to do anything else.
I've tried multiple full firmware's from samsung-updates/sammobile and all drop me back to the same screen (with Odin)
Naturally, I will turn this in to Samsung and wait the time that it takes to have it repaired/replaced for her. I just wanted to know if anyone had any great ideas i could go through before going ahead with this
Thanks in advance
kartoffelpower said:
Hi all,
Before I return this device back to Samsung i wanted to check here if anyone had similar Problems or can possibly help with this.
I've never had the Luxury of personally using this Device, the Original Owner bought it at Duty Free here in Dubai and during the OTA it appears something went wrong. Rather than returning it to Samsung directly (they have a notoriously bad reputation of turn around time here) she asked me to have a look at it
Originally it was stuck in a Bootloop of The Intro of the boy looking through the telescope and appearing with the Samsung logo in a recurring Bootloop. Kies (the terrible software it is) is stuck at the connecting screen and doesn't move further than that.
To the jist;
I cant enter Recovery Mode, it takes me directly to the "downloading" screen. I can however boot manually into the Downloading mode. I've tried reflashing the stock recovery with Odin but still won't allow me to get into it, it boots to download mode before I even get a chance to do anything else.
I've tried multiple full firmware's from samsung-updates/sammobile and all drop me back to the same screen (with Odin)
Naturally, I will turn this in to Samsung and wait the time that it takes to have it repaired/replaced for her. I just wanted to know if anyone had any great ideas i could go through before going ahead with this
Thanks in advance
Click to expand...
Click to collapse
What's the screen you get on Odin? What does it say?
robb13 said:
What's the screen you get on Odin? What does it say?
Click to expand...
Click to collapse
Hi Robb,
Thank you for the reply,
Odin is fine, it flashes without any issues but upon restarting without booting into any special mode, it comes up immediately with "downloading... do not turn of target!!"
When I flash with what i presume would be the correct firmware i get an error (it's bought in Dubai so i figured it was the XSG firmware)
When using the "official XSG" from samsung-updates (zip file EK-GC100_XSG_1_20121121162346) which extracts to GC100XXALK6_GC100OJVALK1_GC100XXALJG_HOME.tar i get this error;
Code:
<ID:0/016> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> GC100XXALK6_GC100OJVALK1_GC100XXALJG_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/016> Odin v.3 engine (ID:16)..
<ID:0/016> File analysis..
<ID:0/016> SetupConnection..
<ID:0/016> Initialzation..
<ID:0/016> Get PIT for mapping..
<ID:0/016> Firmware update start..
<ID:0/016> system.img
<ID:0/016> NAND Write Start!!
<ID:0/016> boot.img
<ID:0/016> cache.img
<ID:0/016> hidden.img
<ID:0/016> recovery.img
<ID:0/016> modem.bin
<ID:0/016>
<ID:0/016> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
However if i flash with GC100XXALJF_GC100OXAALJF_GC100XXALJG_HOME.tar it is successful but after rebooting, its stuck in download mode,
here from Odin;
Code:
<ID:0/016> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> GC100XXALJF_GC100OXAALJF_GC100XXALJG_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/016> Odin v.3 engine (ID:16)..
<ID:0/016> File analysis..
<ID:0/016> SetupConnection..
<ID:0/016> Initialzation..
<ID:0/016> Get PIT for mapping..
<ID:0/016> Firmware update start..
<ID:0/016> boot.img
<ID:0/016> NAND Write Start!!
<ID:0/016> cache.img
<ID:0/016> hidden.img
<ID:0/016> modem.bin
<ID:0/016> recovery.img
<ID:0/016> system.img
<ID:0/016> RQT_CLOSE !!
<ID:0/016> RES OK !!
<ID:0/016> Completed..
<OSM> All threads completed. (succeed 1 / failed 0)
<ID:0/016> Removed!!
<ID:0/016> Added!!
When i boot into download mode/recovery mode myself i'm presented with;
"Odin Mode"
Product Name: EK-GC100_EUR_XX
Custom Binary Download: No
Current Binary: Samsung Official
System Status: Custom
kartoffelpower said:
Hi Robb,
Thank you for the reply,
Odin is fine, it flashes without any issues but upon restarting without booting into any special mode, it comes up immediately with "downloading... do not turn of target!!"
When I flash with what i presume would be the correct firmware i get an error (it's bought in Dubai so i figured it was the XSG firmware)
When using the "official XSG" from samsung-updates (zip file EK-GC100_XSG_1_20121121162346) which extracts to GC100XXALK6_GC100OJVALK1_GC100XXALJG_HOME.tar i get this error;
Code:
<ID:0/016> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> GC100XXALK6_GC100OJVALK1_GC100XXALJG_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/016> Odin v.3 engine (ID:16)..
<ID:0/016> File analysis..
<ID:0/016> SetupConnection..
<ID:0/016> Initialzation..
<ID:0/016> Get PIT for mapping..
<ID:0/016> Firmware update start..
<ID:0/016> system.img
<ID:0/016> NAND Write Start!!
<ID:0/016> boot.img
<ID:0/016> cache.img
<ID:0/016> hidden.img
<ID:0/016> recovery.img
<ID:0/016> modem.bin
<ID:0/016>
<ID:0/016> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
However if i flash with GC100XXALJF_GC100OXAALJF_GC100XXALJG_HOME.tar it is successful but after rebooting, its stuck in download mode,
here from Odin;
Code:
<ID:0/016> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> GC100XXALJF_GC100OXAALJF_GC100XXALJG_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/016> Odin v.3 engine (ID:16)..
<ID:0/016> File analysis..
<ID:0/016> SetupConnection..
<ID:0/016> Initialzation..
<ID:0/016> Get PIT for mapping..
<ID:0/016> Firmware update start..
<ID:0/016> boot.img
<ID:0/016> NAND Write Start!!
<ID:0/016> cache.img
<ID:0/016> hidden.img
<ID:0/016> modem.bin
<ID:0/016> recovery.img
<ID:0/016> system.img
<ID:0/016> RQT_CLOSE !!
<ID:0/016> RES OK !!
<ID:0/016> Completed..
<OSM> All threads completed. (succeed 1 / failed 0)
<ID:0/016> Removed!!
<ID:0/016> Added!!
When i boot into download mode/recovery mode myself i'm presented with;
"Odin Mode"
Product Name: EK-GC100_EUR_XX
Custom Binary Download: No
Current Binary: Samsung Official
System Status: Custom
Click to expand...
Click to collapse
This might help (again, this is why my thread should be a sticky) http://forum.xda-developers.com/showthread.php?t=2086636
Flash the firmware that fails on modem.
Let it fail. Turn off and boot into download mode again.
Then root the camera via odin with the root method Adam gave us.
That flash should go all the way 100%
After this, the camera should work again.
Try it, let us know if it helped.
robb13 said:
This might help (again, this is why my thread should be a sticky) http://forum.xda-developers.com/showthread.php?t=2086636
Flash the firmware that fails on modem.
Let it fail. Turn off and boot into download mode again.
Then root the camera via odin with the root method Adam gave us.
That flash should go all the way 100%
After this, the camera should work again.
Try it, let us know if it helped.
Click to expand...
Click to collapse
Thanks Robb, i've given it a try but it reboots back into Download Mode again
Code:
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> GC100XXALK6_GC100OJVALK1_GC100XXALJG_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/016> Odin v.3 engine (ID:16)..
<ID:0/016> File analysis..
<ID:0/016> SetupConnection..
<ID:0/016> Initialzation..
<ID:0/016> Get PIT for mapping..
<ID:0/016> Firmware update start..
<ID:0/016> system.img
<ID:0/016> NAND Write Start!!
<ID:0/016> boot.img
<ID:0/016> cache.img
<ID:0/016> hidden.img
<ID:0/016> recovery.img
<ID:0/016> modem.bin
<ID:0/016>
<ID:0/016> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
<ID:0/016> Removed!!
<ID:0/016> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> CF-Auto-Root-gd1-gd1xx-ekgc100.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/016> Odin v.3 engine (ID:16)..
<ID:0/016> File analysis..
<ID:0/016> SetupConnection..
<ID:0/016> Initialzation..
<ID:0/016> Get PIT for mapping..
<ID:0/016> Firmware update start..
<ID:0/016> recovery.img
<ID:0/016> NAND Write Start!!
<ID:0/016> cache.img
<ID:0/016> RQT_CLOSE !!
<ID:0/016> RES OK !!
<ID:0/016> Completed..
<OSM> All threads completed. (succeed 1 / failed 0)
<ID:0/016> Removed!!
<ID:0/016> Added!!
I even did a further step of removing modem.bin from the failed tar and repackaging it and reflashing, still returns back to downloading mode.
I do however now have Custom Binary Download: Yes
Downloading Adam's suggested JellyBean 4.1.1 build:GC100XXALK1 and will see if that works for me.
Have you tried getting into recovery?
Sent from my GT-N7100 using Tapatalk 2
RavenY2K3 said:
Have you tried getting into recovery?
Sent from my GT-N7100 using Tapatalk 2
Click to expand...
Click to collapse
I wish i could enter recovery but it no longer works, it takes me straight into downloading mode (even when using the Recovery mode combo when turning the camera on). This download mode is slightly different from the Download Mode launched with the combination, it only shows the Android Avatar + Downloading.... do not turn off target !!. (No odin, no flash counters, etc)
kartoffelpower said:
I wish i could enter recovery but it no longer works, it takes me straight into downloading mode (even when using the Recovery mode combo when turning the camera on). This download mode is slightly different from the Download Mode launched with the combination, it only shows the Android Avatar + Downloading.... do not turn off target !!. (No odin, no flash counters, etc)
Click to expand...
Click to collapse
What about trying to reflash just the recovery alone, stock that is and see if it kicks it into booting into it, to try a wipe perhaps, I've got the stock recovery if you want to give it a try?
Sent from my GT-N7100 using Tapatalk 2
RavenY2K3 said:
What about trying to reflash just the recovery alone, stock that is and see if it kicks it into booting into it, to try a wipe perhaps, I've got the stock recovery if you want to give it a try?
Sent from my GT-N7100 using Tapatalk 2
Click to expand...
Click to collapse
I tried the stock recovery recovery-stock-bll7-EKGC100 without any luck. Now after recent reflashing the camera boots to a white screen rather than downloading mode.I can still boot to download mode with the combination, the flashing counter has been reset but now also i can't flash ANYTHING onto it, got some new nifty error
Code:
<ID:0/017> Added!!
<ID:0/017> Odin v.3 engine (ID:17)..
<ID:0/017> File analysis..
<ID:0/017> SetupConnection..
<ID:0/017> Initialzation..
<ID:0/017> Get PIT for mapping..
<ID:0/017>
<ID:0/017> There is no PIT partition.
I tried using the PIT file from Adam over at thispost but it throws me
Code:
<ID:0/017> Odin v.3 engine (ID:17)..
<ID:0/017> File analysis..
<ID:0/017> SetupConnection..
<ID:0/017> Initialzation..
<ID:0/017> Set PIT file..
<ID:0/017> DO NOT TURN OFF TARGET!!
<ID:0/017>
<ID:0/017> Re-Partition operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
Having some fun with this device, will return it after the weekend if nothing works out, happy to any suggestions though
Thanks to everyone for the help so far
Sounds completely FUBAR, how did you clear the counter or did it do on it's own/by accident? haha.
Sent from my GT-N7100 using Tapatalk 2
RavenY2K3 said:
Sounds completely FUBAR, how did you clear the counter or did it do on it's own/by accident? haha.
Sent from my GT-N7100 using Tapatalk 2
Click to expand...
Click to collapse
Yeah, now that i can't flash roms at all withotu a valid PIT this camera has definitely reached its point where I will be turning it in to the Service center after the weekend.
The Counter Reset itself, i'm guessing once the partitions disappeared it took the count with it too ;-P
kartoffelpower said:
The Counter Reset itself, i'm guessing once the partitions disappeared it took the count with it too ;-P
Click to expand...
Click to collapse
Well..... Every cloud and all that haha
Sent from my GT-P7500 using Tapatalk HD
My GC2 EK-GC200 has same issue
I cant flash any firmware on my GC2, odin alway failed on system.img ... Please give me PIT file of Samsung EK-GC200

[Q] Softbricked phone, only need to get data

Hi,
recently I flashed a wrong recovery file to my i9000. So now I have the phone-triangle-computer logo on the phone....
I am able to get the phone into download mode, but everytime I try to flash a CWM of TWRP tar file via Odin (both 1.83 and 3.07), both fail:
Odin 1.83:
Code:
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> cwm-touch-5.0.2.8-mini.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/010> Odin v.3 engine (ID:10)..
<ID:0/010> File analysis..
<ID:0/010> SetupConnection..
<ID:0/010> Initialzation..
<ID:0/010> Get PIT for mapping..
<ID:0/010> Firmware update start..
<ID:0/010> recovery.img
<ID:0/010>
<ID:0/010> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
Odin 3.07
Code:
<ID:0/010> Added!!
<ID:0/010> Odin v.3 engine (ID:10)..
<ID:0/010> File analysis..
<ID:0/010> SetupConnection..
<ID:0/010> Initialzation..
<ID:0/010> Get PIT for mapping..
<ID:0/010> Firmware update start..
<ID:0/010> recovery.img
<ID:0/010> NAND Write Start!!
This NAND Write Start doesn't complete, or show the progress indicator
I had installed CM10.1 before, and I would like to restore the data on the internal memory, potentially only via CWM, but preferably a little bit more
Anybody got an idea how to get the data or phone restored?
DaSuperGrover said:
Hi,
recently I flashed a wrong recovery file to my i9000. So now I have the phone-triangle-computer logo on the phone....
I am able to get the phone into download mode, but everytime I try to flash a CWM of TWRP tar file via Odin (both 1.83 and 3.07), both fail:
Odin 1.83:
Code:
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> cwm-touch-5.0.2.8-mini.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/010> Odin v.3 engine (ID:10)..
<ID:0/010> File analysis..
<ID:0/010> SetupConnection..
<ID:0/010> Initialzation..
<ID:0/010> Get PIT for mapping..
<ID:0/010> Firmware update start..
<ID:0/010> recovery.img
<ID:0/010>
<ID:0/010> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
Odin 3.07
Code:
<ID:0/010> Added!!
<ID:0/010> Odin v.3 engine (ID:10)..
<ID:0/010> File analysis..
<ID:0/010> SetupConnection..
<ID:0/010> Initialzation..
<ID:0/010> Get PIT for mapping..
<ID:0/010> Firmware update start..
<ID:0/010> recovery.img
<ID:0/010> NAND Write Start!!
This NAND Write Start doesn't complete, or show the progress indicator
I had installed CM10.1 before, and I would like to restore the data on the internal memory, potentially only via CWM, but preferably a little bit more
Anybody got an idea how to get the data or phone restored?
Click to expand...
Click to collapse
This kernel will help you. It is flashable via Odin.
kevinrus123 said:
This kernel will help you. It is flashable via Odin.
Click to expand...
Click to collapse
Thanks! It worked!
Can't say how pleased I am, these fora are just great!
DaSuperGrover said:
Thanks! It worked!
Can't say how pleased I am, these fora are just great!
Click to expand...
Click to collapse
No problem
Thank you for hitting thanks button

[Q] Galaxy Gear Update

Hi Everyone, i have searched through the forums and tried what has been said, but still no luck. I have a galaxy Gear V700
I tried numerous times on kies to update and it just would not play ball at all.Even leaving it over night, thinking maybe it is downloading something.
Today i have used Odin today, and flashed with V700XXUCNF1_V700OXACNF1_BTU
Within Odin it does the following
<ID:0/004> Added!!
<ID:0/004> Odin v.3 engine (ID:4)..
<ID:0/004> File analysis..
<ID:0/004> SetupConnection..
then it freezes. Because it had froze for about 25 minutes, i unpluged the Gear, to try again. All of a sudden Odin jumped up and said failed, and the Gear now is stuck with "Firmware Upgrade encountered an issue, please select recovery mode in kies and try again"
Problem is Kies 2 and 3 do not recognise the watch anymore. Odin seems to recognise it but wont allow me to do anything . I have tried using Odin to flash an original stock image, and have even tried the earlier Tizan.
I am still stuck...
I am a complete newbie on here and do not really know much about the phones and watches, but got so frustrated at not being able to upgrade the traditional way.
Any help would be greatly appreciated..
Many thanks
:crying::crying::crying:
I am now getting this in Odin 3.09, so it seems to be going a little further, but still fails at the end
<ID:0/005> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> V700XXUCNF1_V700OXACNF1_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/005> Odin v.3 engine (ID:5)..
<ID:0/005> File analysis..
<ID:0/005> SetupConnection..
<ID:0/005> Initialzation..
<ID:0/005> Get PIT for mapping..
<ID:0/005> Firmware update start..
<ID:0/005> SingleDownload.
<ID:0/005> sboot.bin
<ID:0/005> NAND Write Start!!
<ID:0/005> zImage
s0mewhitedude said:
I am now getting this in Odin 3.09, so it seems to be going a little further, but still fails at the end
<ID:0/005> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> V700XXUCNF1_V700OXACNF1_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/005> Odin v.3 engine (ID:5)..
<ID:0/005> File analysis..
<ID:0/005> SetupConnection..
<ID:0/005> Initialzation..
<ID:0/005> Get PIT for mapping..
<ID:0/005> Firmware update start..
<ID:0/005> SingleDownload.
<ID:0/005> sboot.bin
<ID:0/005> NAND Write Start!!
<ID:0/005> zImage
Click to expand...
Click to collapse
I had this issue when trying to flash an incorrect image.
Sent from my SPH-L900 using XDA Premium HD app
I have just answered your question in the Q&A forum.
Also a suggestion, please do not post questions in the General forum, and do not double post.

flashed custom recovery but still getting the stock one !

everytime i flash a custom recovery all i get is the same samsung stock recovery (note 5 sm-n920c)
and i don't know why , and by the way when i flash the custom recovery odin tells that everything is completed without of errors !! , but still getting the stock recovery !
here is what appears in odin when i flash it
<ID:0/006> Added!!
<OSM> Enter CS for MD5..
<OSM> Binary Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/006> Odin engine v(ID:3.1100)..
<ID:0/006> File analysis..
<ID:0/006> SetupConnection..
<ID:0/006> Initialzation..
<ID:0/006> Get PIT for mapping..
<ID:0/006> Firmware update start..
<ID:0/006> SingleDownload.
<ID:0/006> recovery.img
<ID:0/006> NAND Write Start!!
<ID:0/006> RQT_CLOSE !!
<ID:0/006> RES OK !!
<ID:0/006> Removed!!
<ID:0/006> Remain Port .... 0
<OSM> All threads completed. (succeed 1 / failed 0)
please help guys :crying:
abodi40400 said:
everytime i flash a custom recovery all i get is the same samsung stock recovery (note 5 sm-n920c)
and i don't know why , and by the way when i flash the custom recovery odin tells that everything is completed without of errors !! , but still getting the stock recovery !
here is what appears in odin when i flash it
<ID:0/006> Added!!
<OSM> Enter CS for MD5..
<OSM> Binary Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/006> Odin engine v(ID:3.1100)..
<ID:0/006> File analysis..
<ID:0/006> SetupConnection..
<ID:0/006> Initialzation..
<ID:0/006> Get PIT for mapping..
<ID:0/006> Firmware update start..
<ID:0/006> SingleDownload.
<ID:0/006> recovery.img
<ID:0/006> NAND Write Start!!
<ID:0/006> RQT_CLOSE !!
<ID:0/006> RES OK !!
<ID:0/006> Removed!!
<ID:0/006> Remain Port .... 0
<OSM> All threads completed. (succeed 1 / failed 0)
please help guys :crying:
Click to expand...
Click to collapse
Did you enable OEM UNLOCK under developer options ?
abodi40400 said:
everytime i flash a custom recovery all i get is the same samsung stock recovery (note 5 sm-n920c)
and i don't know why , and by the way when i flash the custom recovery odin tells that everything is completed without of errors !!
Click to expand...
Click to collapse
Flash the recovery with Auto Reboot unchecked.

Categories

Resources