**
I think i just bricked it.
it is now stuck on the N screen
been stuck there for 10 minutes. not going anywhere
i am looking but cant find anything on what to do now.
any suggestions?
thanks guys
Hello,
I want the new upgrade so i was trying yo go back to stock but i must be doing something wrong.
first i tried method one
...Flash_back_to_clean_stock_ROM[/url]
and at 7 clockworkmod opens up and it never goes into the " re-flash its /system partition"
so then i tried connecting to my computer and using adb but it always just says there is no device found.
anyone have any idea on what I am missing?
my nook is 1.0.1
Have you tried the manual 8 interrupted boots?
yes and on the 7th interrupt clockworkmod started.
seems irreverent now that i am stuck on the n spalsh screen.
thank you for your reply
but i think i buggered things up
So, to make a long story, short, for the past couple of days my phone has been soft-bricked... It first happened when I attempted to flash dmodv6 in CWM. Everything looked good throughout the installation, however, when I rebooted my device, I got stuck in a boot loop where It would say "Samsung Galaxy S III GT-I8190" for a few seconds, the screen would go black, then say the same thing again... over and over and over...
After a lot of trial and error because of NOT making a nandroid backup via CWM (stupid, I know - I had made one via Titanium Backup and thought that might be good enough), I finally was able to boot. Thanks to xXPR0T0TYPEXx, I was able to flash another rom by puting my external sd card into another phone, loading another rom onto it, and putting it back in my phone. I now had Cyanogenmod10 and was able to boot back up.
I attempted to restore the Titanium Backup I had made with this new rom (stupid again, I know) and it made almost every service on the phone stop working... I desperately wanted just to get back to square one - to install stock firmware and go from there. I followed tys0n's guide on flashing stock recovery then attempted to install stock firmware... All seemingly went well - I booted up, got past the initial "Samsung Galaxy S III GT-I8190" logo and finally got hung up at the "Samsung" logo. I left it one while I went to sleep, just to see if it would eventually work... I woke up and it was still the same. I tried flashing different version of the same stock firmware but it all ended in getting hung up at the "Samsung" logo.
A major problem is that I absolutely CANNOT flash a custom recovery via Odin - it just will NOT work. Everything looks good on Odin's end - I PASS, get the (succeed 1 / failed 0) thing but am sent to stock recovery every time I do the 3 button combination. I've tried many version of CWM and TWRP.... NOTHING. I've even unticked the "Auto-Reboot" button in Odin and pulled the usb cable and battery upon completion but, but nothing ever works. The only way I was ever able to get CWM on my phone in the first place was by an in-phone app... Rom Manager, maybe? I can't remember. But, as it is, that method is out of the question.
I've learned a lot about what I did wrong so that's the only good part of all of this. Now, all that's left is to fix the thing so I can go about it right. I'm completely out of ideas, have spent almost a full 24 hours searching solutions to this problem and I am at wits end...
I just want to get back to stock firmware... Any ideas, guys? Should I go about re-partitioning my device at this time?
I have the PIT file... but I'm not sure as to which firmware to choose. I imagine a firmware that is 4.1.1 like my phone was... but I'm not sure about the region. I live in the US and there is no US or North American region firmware version.Can anyone shed some light on which one I should choose?
My SSN underneath my battery say "GTI8190GSMH".
I'm sorry this is so long, I just wanted to explain what happened as best as I could. So, should I go about re-partitioning my device at this point? If so, what firmware would you recommend for my model? Are different region versions okay for a this method?
Or is there another way?
Thanks, guys. :silly:
Some additional details (if it will help): I can, indeed, boot into both recovery and download mode. I just can't seem to flash a stock rom that will boot past the "Samsung" logo.
I've even attempted to flash the param file after the rom flash but it didn't help.
AffectiveEffect said:
Some additional details (if it will help): I can, indeed, boot into both recovery and download mode. I just can't seem to flash a stock rom that will boot past the "Samsung" logo.
I've even attempted to flash the param file after the rom flash but it didn't help.
Click to expand...
Click to collapse
Do you have the stock recovery now instead CWM? If yes do (if you didn't try it) a factory/data reset and wipe cache but it will delete your pics, music etc on your internal storage too.
xXPR0T0TYPEXx said:
Do you have the stock recovery now instead CWM? If yes do (if you didn't try it) a factory/data reset and wipe cache but it will delete your pics, music etc on your internal storage too.
Click to expand...
Click to collapse
Yeah, I have stock recovery now and I have tried that many, many times... Even if I install something like CyanogenMod, it still gets hung up on the CyanogenMod boot screen... And if I boot a stock firmware, it gets hung up at the same place at the "Samsung" logo...
I have an idea that one of the only options left is a PIT re-partitioning... If so, how would I properly go about that? Load the PIT file and the stock firmware in odin? Or only the PIT as PDA? I've heard a couple of different things and am unsure.
AffectiveEffect said:
Yeah, I have stock recovery now and I have tried that many, many times... Even if I install something like CyanogenMod, it still gets hung up on the CyanogenMod boot screen... And if I boot a stock firmware, it gets hung up at the same place at the "Samsung" logo...
I have an idea that one of the only options left is a PIT re-partitioning... If so, how would I properly go about that? Load the PIT file and the stock firmware in odin? Or only the PIT as PDA? I've heard a couple of different things and am unsure.
Click to expand...
Click to collapse
I don't know about PIT files but some people got this message : "CUSTOM PIT BINARY" in recovery mode after flashed a PIT file (maybe they used a other PIT file that wasn't compatible). So make sure you use a PIT file that is GT-i8190 compatible.
I tried flashing the PIT file for the hell of it because I am completely out of ideas.... It failed repeatedly in Odin.
I have no clue on how to fix this... I've tried countless roms and they all get stuck on their respective boot screens. The only one that gave me a glimmer of hope was Cyanogenmod10.2.... It went as far as saying "Android is upgrading" and showed "starting apps" but it got hung up there.
I don't know what to do, guys. Someone help!!!
AffectiveEffect said:
I tried flashing the PIT file for the hell of it because I am completely out of ideas.... It failed repeatedly in Odin.
I have no clue on how to fix this... I've tried countless roms and they all get stuck on their respective boot screens. The only one that gave me a glimmer of hope was Cyanogenmod10.2.... It went as far as saying "Android is upgrading" and showed "starting apps" but it got hung up there.
I don't know what to do, guys. Someone help!!!
Click to expand...
Click to collapse
Use a custom ROM to see if it will fix the problem .Try to flash CyanogenMod 10.2 by NovaFusion via odin or if you flash CyanogenMod 11 then you will automatically get the TWRP recovery. NovaFusion Team Homepage : novafusion.pl. I know you want the stock ROM but try other ROMs to get a booting phone again
xXPR0T0TYPEXx said:
Use a custom ROM to see if it will fix the problem .Try to flash CyanogenMod 10.2 by NovaFusion via odin or if you flash CyanogenMod 11 then you will automatically get the TWRP recovery. NovaFusion Team Homepage : novafusion.pl. I know you want the stock ROM but try other ROMs to get a booting phone again
Click to expand...
Click to collapse
I have... I've tried numerous stock roms and numerous custom roms... all versions of Cyanogenmod, Chameleon, Carbon, Slim mod, etc... They all get stuck at their respective logos.
I even tried the Cyanogenmod with TWRP but, as I explained earlier, I absolutely CAN NOT flash a custom recovery unless I use what ever app I used.... It doesn't work with Odin or with a rom. I don't know why.
I wish someone had more info on repartitioning my phone and if it would help.
NEED HELP?
AffectiveEffect said:
So, to make a long story, short, for the past couple of days my phone has been soft-bricked... It first happened when I attempted to flash dmodv6 in CWM. Everything looked good throughout the installation, however, when I rebooted my device, I got stuck in a boot loop where It would say "Samsung Galaxy S III GT-I8190" for a few seconds, the screen would go black, then say the same thing again... over and over and over...
After a lot of trial and error because of NOT making a nandroid backup via CWM (stupid, I know - I had made one via Titanium Backup and thought that might be good enough), I finally was able to boot. Thanks to xXPR0T0TYPEXx, I was able to flash another rom by puting my external sd card into another phone, loading another rom onto it, and putting it back in my phone. I now had Cyanogenmod10 and was able to boot back up.
I attempted to restore the Titanium Backup I had made with this new rom (stupid again, I know) and it made almost every service on the phone stop working... I desperately wanted just to get back to square one - to install stock firmware and go from there. I followed tys0n's guide on flashing stock recovery then attempted to install stock firmware... All seemingly went well - I booted up, got past the initial "Samsung Galaxy S III GT-I8190" logo and finally got hung up at the "Samsung" logo. I left it one while I went to sleep, just to see if it would eventually work... I woke up and it was still the same. I tried flashing different version of the same stock firmware but it all ended in getting hung up at the "Samsung" logo.
A major problem is that I absolutely CANNOT flash a custom recovery via Odin - it just will NOT work. Everything looks good on Odin's end - I PASS, get the (succeed 1 / failed 0) thing but am sent to stock recovery every time I do the 3 button combination. I've tried many version of CWM and TWRP.... NOTHING. I've even unticked the "Auto-Reboot" button in Odin and pulled the usb cable and battery upon completion but, but nothing ever works. The only way I was ever able to get CWM on my phone in the first place was by an in-phone app... Rom Manager, maybe? I can't remember. But, as it is, that method is out of the question.
I've learned a lot about what I did wrong so that's the only good part of all of this. Now, all that's left is to fix the thing so I can go about it right. I'm completely out of ideas, have spent almost a full 24 hours searching solutions to this problem and I am at wits end...
I just want to get back to stock firmware... Any ideas, guys? Should I go about re-partitioning my device at this time?
I have the PIT file... but I'm not sure as to which firmware to choose. I imagine a firmware that is 4.1.1 like my phone was... but I'm not sure about the region. I live in the US and there is no US or North American region firmware version.Can anyone shed some light on which one I should choose?
My SSN underneath my battery say "GTI8190GSMH".
I'm sorry this is so long, I just wanted to explain what happened as best as I could. So, should I go about re-partitioning my device at this point? If so, what firmware would you recommend for my model? Are different region versions okay for a this method?
Or is there another way?
Thanks, guys. :silly:
Click to expand...
Click to collapse
i got same problem with you before im wayback dmod v6 before and stuck at samsung logo i just try hard reset
1. open your phone
2. remove battery and put the battery try and try til u get in recovery mode (CWM) maybe just tried almost 20x restarting in logo til u in CWM :victory:
3. re-Flash your dmod v6 this way for dirty rom like what i said (softbricks)
4. just flash another new rom whatever u like or dmod v6.
5. I HOPE IT HELPS DONT FORGET TO THANKS <3 :highfive:
Hi all,
I really need your guys help. Out of nowhere today my phone restarted and then got stuck in a bootloop. When I went into recovery, it gave me the "android is updating" pop-up. I knew there was no update and within 20 seconds or so it said "no command". I went through to wipe the cache, and after rebooting it back up, strangely it didn't give me the "android is updating" screen that occurs after wiping cache. I went ahead and tried to factory reset through recovery and everything was fine until I got a msg "E: could not mount (file or directory could not be found) or something a long those lines. I'm assuming the EFS is fried? I rebooted it after and even at the "Welcome Screen" it started boot looping again. I'm stock lollipop unrooted. I never rooted this phone or flashed any ROMs. I called T-Mo and they will send me a replacement but I still want to see if this can be fixed. I also don't have a replacement phone so..there's that. Would anyone be able to help?
Edit: The only thing I haven't tried is flashing the stock firmware via odin. Would this trip the knox counter though? I really want to avoid that especially since I am having these issues and I don't want tmo/samsung to think I caused this issue.
Bad phone. Ur new phone will be good to go.
BAD ASS NOTE 4
Hey everyone,
I'm having a problem after trying to flash CM12.1 on a i8190l.
The instructions I basically followed are the ones mentioned here: novafusion.pl/tutorials/installation-guide-golden/ and I used the rom Lollipop 5.0.2 (CyanogenMod 12.0) 20150428 stable with the Odin app to install it.
All went well up to the point 12. Click on Wipe, then use slider on the bottom to let process begin.
At this point I received a FAILED message with an error message saying below that /data couldn't be mounted. After that, I rebooted the phone, and it started loading the first android screen apparently. After a few minutes, Android threw up an error saying that it couldn't encrypt the data and had to reboot. After that reboot, the system won't stop going over a loop boot that flashes TeamWin over and over again.
I can still get to the download mode, what is the recommended step to take from here? Is it possible to recover the OS? Do I have to worry about the battery running out, or does it charge up while on download mode/other mode?
Thanks for your help
I'm a complete newbie to android phone modding, and I was really proud of myself when I was able to install the Cyanogen 12.1 and Google Apps onto my Samsung S3 Mini. However, I made the mistake of trying to put my work email on it, which requires that my phone be encrypted. Well, I guess the encryption and rooted phone didn't want to play nice together, so I got the error message that my phone would be factory reset. Boo! Well, it got worse. Instead of a factory reset, my rooted phone now is stuck in what I have now learned is called a bootloop. Basically I turn my phone on, and the Cyanogen start screen (with the text "TEAMWIN") just infinitely flashes on the screen until I pull the battery.
I have tried using Odin 3.07 and cm12.1_golden.nova.20160210.ODIN_TWRP.tar.md5. I do the three button system boot, connect the usb, run Odin, get the phone recognized, and then install the .md5 in the PDA section of Odin. It tells me that it succeeded, but when I restart my phone it's still the same bootloop. I also tried swearing, but that didn't help either.
Has anyone else out there had experience with Cyanogen and this particular error? I would love to get this phone working again... preferably with either a Lollipop version of android or back to Cyanogen 12.1.
Any info would be greatly appreciated! Thanks everyone.
So I've got an update if anyone's interested... I can't call it progress, but it's a different problem now.
I was able to download and use Odin to do what was shown on this link: http://forum.xda-developers.com/showthread.php?t=2122548&highlight=root
Everything worked in Odin, the phone rebooted, and went to the Team Win Recovery Project diagnostics screen, rebooted again, and then to the samsung logo. However, it immediately goes to the "Encryption Failed" error screen, and the only option is to 'reset device'. Of course, doing this just reboots the phone and it then has the Team Win loading screen, Team Win Recovery Project diags screen, Samsung logo, and back to the 'Encryption Failed' screen again. So now I have a new infinite loop to solve. *sigh*
any thoughts?
Have you been able to get into TWRP? If you are, maybe you could wipe everything from there and flash the recovery version of your ROM.
I was able to put the stock bootloader onto the phone using Odin, download the original tar from here: http://live.samsung-updates.com/index.php?device=GT-I8190, then used the stock bootloader to install it from the sd card. Everything went fine, but now when I boot the phone it just hangs on the Samsung Galaxy S3 mini GT-i18190 start screen indefinitely. Is this progress, or have I created a new problem now?
You're playing around with heavy stuff. I won't recommend using an upgrade flash (CM over Odin) as an full flash. Please try flashing a stock image.
If you did something wrong to the partitioning, then it's likely to not allow you to do a successfull factory reset. Maybe you can try re-flashing a stock Odin image with PIT repartitioning.
Remember to try to backup the EFS folder, doing that kind of flash might wipe it.