hello friends..i am using cm10.1.3 latest based on 4.2.2 jellybean.I always set my cpu speed at 480 megahertz... and in that speed when i tried to multitasking it just gets a fast reboot..i think the problem is only for cm10.1...now is there any way to solve it???
my device info:
model: gts 5830
rom: cm 10.1.3 latest
ram: default 26% (72 mb)
kernel: default of cm 10.1
debajyoti1 said:
hello friends..i am using cm10.1.3 latest based on 4.2.2 jellybean.I always set my cpu speed at 480 megahertz... and in that speed when i tried to multitasking it just gets a fast reboot..i think the problem is only for cm10.1...now is there any way to solve it???
my device info:
model: gts 5830
rom: cm 10.1.3 latest
ram: default 26% (72 mb)
kernel: default of cm 10.1
Click to expand...
Click to collapse
Usually multitasking on CM 10 and above always slows down your device because of huge RAM and CPU requirement. Can you try increasing the CPU speed to 800 MHz and see if it makes a difference? If it doesn't, then it must a problem with the rom. Don't forget our device was not meant to get an official update after Gingerbread because of its low hardware specifications. Do post the result. Hope I Helped
debajyoti1 said:
ram: default 26% (72 mb)
Click to expand...
Click to collapse
You Need To Disable zRAM.
BTW: The Latest From CM 10.1 Branch is 10.1.6
mahithm said:
Usually multitasking on CM 10 and above always slows down your device because of huge RAM and CPU requirement. Can you try increasing the CPU speed to 800 MHz and see if it makes a difference? If it doesn't, then it must a problem with the rom. Don't forget our device was not meant to get an official update after Gingerbread because of its low hardware specifications. Do post the result. Hope I Helped
Click to expand...
Click to collapse
yes bro I know that our ace is old,outdated and have low hardware...i am facing the problem in @800 megahertz also when i type very fast,or do any activities (touches) very fast and the problem is only with cm 10.1 so i thought there might be any solution.. btw thanx for your reply..
thanx
waqaswasil said:
You Need To Disable zRAM.
BTW: The
yes may be but mine rom is latest....yes its reduce the lag of rebooting..
Click to expand...
Click to collapse
debajyoti1 said:
yes bro I know that our ace is old,outdated and have low hardware...i am facing the problem in @800 megahertz also when i type very fast,or do any activities (touches) very fast and the problem is only with cm 10.1 so i thought there might be any solution.. btw thanx for your reply..
Click to expand...
Click to collapse
Better post this problem at the rom thread. Rom developer would be able to provide a solution to your problem
Which min freq value are you using?
Related
Hello xda,
I am posting here as i do not have sufficient rights to post in developer section.
My Q is that is anyone facing problem in boype's modded CyanogenMod 7 latest builds:
cm-7-package-20120916-p970-boype
cm-7-package-20120909-p970-boype
I am facing atleast one SOD per day.
This is not an accusation,just a question.
If anyone could solve the problem.
Even bagr84 is also facing the problem as he said in his reply.
http://forum.xda-developers.com/showthread.php?t=1734312&page=155
Thanks.
e1forall said:
Hello xda,
I am posting here as i do not have sufficient rights to post in developer section.
My Q is that is anyone facing problem in boype's modded CyanogenMod 7 latest builds:
cm-7-package-20120916-p970-boype
cm-7-package-20120909-p970-boype
I am facing atleast one SOD per day.
This is not an accusation,just a question.
If anyone could solve the problem.
Even bagr84 is also facing the problem as he said in his reply.
http://forum.xda-developers.com/showthread.php?t=1734312&page=155
Thanks.
Click to expand...
Click to collapse
Did you do a full wipe before installing the ROMs? Did you restore apps and data with Titanium Backup?
I only had that problem, when I either not did a full wipe, or restored via TB.
N00BY0815 said:
Did you do a full wipe before installing the ROMs? Did you restore apps and data with Titanium Backup?
I only had that problem, when I either not did a full wipe, or restored via TB.
Click to expand...
Click to collapse
Thanks for the quick reply.
I do data reset and dalvik cache reset from CWM before flashing any rom
and
I always do the all apps manual installation process after flashing any rom.
Same problem I faced in both the builds I mentioned.
Before the cm-7-package-20120909-p970-boype build the rom was stable for me.
Never tried tweaking anything else except for the graphic ones.
Thanks
I got SODs with the 20120909 build. They went away after I set the minimum CPU clock to 400MHz (interactivex-governor).
OptiMyst said:
I got SODs with the 20120909 build. They went away after I set the minimum CPU clock to 400MHz (interactivex-governor).
Click to expand...
Click to collapse
Thanks for the reply
Currently i rebeveted back to 20120905 from 20120916...That is i flashed 20120905 back on 20120916
Did wipe/reset, wipe dalvik cache, cache reset.
No SODs so far ...
But facing a new problem.. when I connect my phone to mass storage it restarts.
Any clue?
And on 20120905 the minimum cpu clock is 200MHz default governor and still no sod.
And doesnt setting minimum cpu clock to 400MHz will eat battery?
Any solution for my new problem?
No replies?
No one is facing such problems?
Sorry but what is SOD. New here that's why asking..
Sent from my LG-P970 using Tapatalk 2
vishaldhamnekar said:
Sorry but what is SOD. New here that's why asking..
Sent from my LG-P970 using Tapatalk 2
Click to expand...
Click to collapse
Screen of death. Frozen screen
vishaldhamnekar said:
Sorry but what is SOD. New here that's why asking..
Sent from my LG-P970 using Tapatalk 2
Click to expand...
Click to collapse
Probably a mac user?
On Topic:
I had no problems on interactivex
OptiMyst said:
I got SODs with the 20120909 build. They went away after I set the minimum CPU clock to 400MHz (interactivex-governor).
Click to expand...
Click to collapse
Hey
Thanks man.. it helped...
back to boype's 20120916 build and minimum clock to 400MHz ....
no sods so far... :laugh:
Just a quick notice: I've upgraded to boype's 20120925 build yesterday which contains changes to help against SODs. I've changed minimum clock back to 200 MHz to see if it the new version is better. I had no SOD so far. I'll keep an eye on it.
OptiMyst said:
Just a quick notice: I've upgraded to boype's 20120925 build yesterday which contains changes to help against SODs. I've changed minimum clock back to 200 MHz to see if it the new version is better. I had no SOD so far. I'll keep an eye on it.
Click to expand...
Click to collapse
Hey
I have also upgraded to 20120925 build but have the same settings as before.
Governor - interactivex
min cpu freq - 400 MHz
I'll too change it to 200 and chek.
Thanks.
I had few SoDs after I've updated to the latest build. I've change minimum freq to 400MHz.
I had no SODs, but I had two spontaneous reboots to recovery-mode while in standby. I'm also going back to 400 MHz minimum clock now.
Yeah minimum clock to 400 MHz works fine.... no SOD's so far ... using at this setting since my last reply.
This maybe out of topic but anyone facing USB mass storage problem, the flash drive not shown on the computer screen or instant restart at USB mass connection turned on ...
??
where are you man..don't stay at stoneage.....go to future...
Now trend is CM10....enjoy the jellybean
pvsukumars said:
where are you man..don't stay at stoneage.....go to future...
Now trend is CM10....enjoy the jellybean
Click to expand...
Click to collapse
Any suggestions.....STABLE BUILD I mean for daily use....
Thanks
e1forall said:
Any suggestions.....STABLE BUILD I mean for daily use....
Thanks
Click to expand...
Click to collapse
The M2 build is doing a pretty good job but check it out on your own
Sent from my LG-P970 using xda app-developers app
N00BY0815 said:
The M2 build is doing a pretty good job but check it out on your own
Sent from my LG-P970 using xda app-developers app
Click to expand...
Click to collapse
Aah yes.. I'll try this thing...
Here's the link
http://get.cm/?device=p970&type=snapshot
e1forall said:
Aah yes.. I'll try this thing...
Here's the link
http://get.cm/?device=p970&type=snapshot
Click to expand...
Click to collapse
i want to use boypes rom
but i have always sods
launcher goes crazy
etc.
which cpu settings no sods no fcs no wakelocks and without problems?
could you tell me?
Hello everyone. I am installed einstein.frat's kernel and russell's revolution rom to my telephone. Actually, they are working very nicely but sometimes my telephone restarting for no reason. I don't understand why. Can you help me?
i'm sorry, my english very bad.
odunluzikkim said:
Hello everyone. I am installed einstein.frat's kernel and russell's revolution rom to my telephone. Actually, they are working very nicely but sometimes my telephone restarting for no reason. I don't understand why. Can you help me?
i'm sorry, my english very bad.
Click to expand...
Click to collapse
Some devices have this problem.Try reducing the overclock speed to 680mhz (No reboots at this frequency ) Or you can just install the stock kernel too.
nikhil16242 said:
Some devices have this problem.Try reducing the overclock speed to 680mhz (No reboots at this frequency ) Or you can just install the stock kernel too.
Click to expand...
Click to collapse
Thank you mate . I opened No-frills CPU Control program and I choose the max frequency 678 mhz. I'm trying now.
thank you for help
HI...
i wanna know if gpu overclocking is possible for our device????? the one like Kerner Tuner for HTC EVO 3D????
i searched over internet and found out this : http://rootzwiki.com/topic/27167-ke...-last-senseful-edition-aospsense-caf-drivers/
but it didnt mention whether it is supported for jb roms or not????
mnomaanw said:
HI...
i wanna know if gpu overclocking is possible for our device????? the one like Kerner Tuner for HTC EVO 3D????
i searched over internet and found out this : http://rootzwiki.com/topic/27167-ke...-last-senseful-edition-aospsense-caf-drivers/
but it didnt mention whether it is supported for jb roms or not????
Click to expand...
Click to collapse
Of course. Any rom made by me or albino has that option. Some other kernels may have it but it all depends.
i am currently on [ROM] CM10.1 AOSP 4.2.2 Jellybean [KANG] [Aug-6] by albinoman887.....
GPU OC is unsupported in kernel tuner.....also i cant overclock cpu thru "Performance".....and i am looking for a kernel update supporting jb 4.2.2
i tried this http://forum.xda-developers.com/showthread.php?t=2156949.............it said it supported jb but i guess it was ony for 4.1.x
mnomaanw said:
i am currently on [ROM] CM10.1 AOSP 4.2.2 Jellybean [KANG] [Aug-6] by albinoman887.....
GPU OC is unsupported in kernel tuner.....also i cant overclock cpu thru "Performance".....and i am looking for a kernel update supporting jb 4.2.2
i tried this http://forum.xda-developers.com/showthread.php?t=2156949.............it said it supported jb but i guess it was ony for 4.1.x
Click to expand...
Click to collapse
If you read there are instructions on how to edit the Kernel in the page you get the ROM from.
mnomaanw said:
i am currently on [ROM] CM10.1 AOSP 4.2.2 Jellybean [KANG] [Aug-6] by albinoman887.....
GPU OC is unsupported in kernel tuner.....also i cant overclock cpu thru "Performance".....and i am looking for a kernel update supporting jb 4.2.2
i tried this http://forum.xda-developers.com/showthread.php?t=2156949.............it said it supported jb but i guess it was ony for 4.1.x
Click to expand...
Click to collapse
The question is why...
Overclocking the GPU does almost nothing in terms of performance... No faster in UI in my experience... And... No better in benchmark (I know they mean nothing)
It actually just drains battery IMHO...
Sent from my Vivid 4G using Tapatalk 4
rignfool said:
The question is why...
Overclocking the GPU does almost nothing in terms of performance... No faster in UI in my experience... And... No better in benchmark (I know they mean nothing)
It actually just drains battery IMHO...
Sent from my Vivid 4G using Tapatalk 4
Click to expand...
Click to collapse
Yeah thats what im telling to my friend (who posted the OP using my account) ...thank god you answered. Now he will stop bi***ing
Sent from my Evo 3D CDMA using Tapatalk 4
mnomaanw said:
HI...
i wanna know if gpu overclocking is possible for our device????? the one like Kerner Tuner for HTC EVO 3D????
i searched over internet and found out this : http://rootzwiki.com/topic/27167-ke...-last-senseful-edition-aospsense-caf-drivers/
but it didnt mention whether it is supported for jb roms or not????
Click to expand...
Click to collapse
Almost cook room has overclocking, you can set in Performance settings (with CM room) or venom tweak(if using venom room).
For me, if no using some big application, I often set max CPU freq. <1200 htz and min <384htz. I realized when set max CPU > 1250 htz, my device is getting hotter, religion battery
hungpd00532 said:
Almost cook room has overclocking, you can set in Performance settings (with CM room) or venom tweak(if using venom room).
For me, if no using some big application, I often set max CPU freq. <1200 htz and min <384htz. I realized when set max CPU > 1250 htz, my device is getting hotter, religion battery
Click to expand...
Click to collapse
You're talking CPU...
He wanted to know about GPU
Sent from my Vivid 4G using Tapatalk 4
[GT-i9195][cm11] - [ROM](Feb.2016)&[kernel](ECOACTIVE & ECOPLUG)(OC/UV)(20151210)
This is a GT-I9195 CM11 kernel highly optimized to best possible performance and energy efficiency.
It may work on Slim (confirmed), AICP (confirmed) and Carbon Rom (confirmed) as well.
It will not work on any Samsung Stock based ROM.
- built from latest avalable CM sources
- CPU OC: 1998 Mhz (light: 1782 MHz) (default and max.)
- reworked freq- tables (unique 108 MHz-steps) for fast scaling
- CPU UV: -50mv (light: -25mv) (default, adjustable)
- GPU OC: freq steps changed to 192-400-608 MHz (light: 192-400-554 MHz)
- L2 OC/UV for extra performance (stock setting is a bottleneck, especially with OC)
- improved bus scaling
- RAM UV
- adjusted msm_thermal to prevent too much thermal throttling under heavy load
- added new "ECOACTIVE" governor and set as default
- added new "ECOPLUG" hotplug driver and set as default
- added FIOPS IO Scheduler and set as default
- added some more commonly used IO schedulers
- added fast random (and enabled via init.d)
- built with official gcc 4.8 with -O3 flags
"ECOACTIVE" is the ultimate governor for lag free performance and good battery life at the same time. It's based on interactive governor. It has a special input gain including the menu, home and back buttons. Separate input gain, fullspeed and eco/screen off phases minimize the use of high frequencys whithout slowing down the device noticably. The upscaling is more agressive during the input phase (default 1s). In the following fullspeed phase (default 10s, set to 0 for unlimited) full performance is allowed. The third phase is configured for battery saving usage while reading, watching videos, music listening or when the screen is off. This ensures maximum responsiveness and best gamig experience along with best possible battery life when reading, listening to music etc.
"ECOPLUG" is an alternative hotplug driver based on AutoSMP. It works much snappier on our device than the stock msm-mpdecision. On default setting second core is down when screen is off.
Everything is fully "pretweaked".
Flash from recovery, enyoy... no need to adjust anything via init.d or app.
Dont flash this kernel if you don't know how to fix problems after flashing !
Make a backup before flashing this kernel !
The hardware parameters are adapted near to the limits of my phone. This means this kernel will not work if your devices hardware cannot handle the OC/UV.
If you are lucky you run the fastest kernel available for your phone
If your phone doesn't run with the "lombartz kernel" you may try the "lombartz light kernel" with less agressive OC/UV.
My latest pure CM11 ROM build (Feb. 2016):
https://drive.google.com/open?id=0B-1RyGtdRvCwWEVfc0ZhTTRzdXc
If you use Xposed framework you need to flash XposedFix after ROM.
regards,
lombartz
...updated.
this kernel is amazing but i have a problem when i connect the smartphone at bluetooth radio. In this case my smartphone freeze and always reboot.
sorry for my english
Hi, thanks for yor feedback Have you already checked if you have the same problem with the last official CM11 kernel from 20150105 ?
regards,
lombartz
edit: tested with my laptop as bluetooth- speaker with no problems. My actual Version is heavily tweaked at the Moment but nothing changed with audio or bluetooth.
Anyone else with bluetooth- playback issues out there ?
edit: found a possible reason for the problem. hope it's fixed in new version (see OP)
Thank you for this. Any chance to include f2fs into the kernel?
bongster said:
Thank you for this. Any chance to include f2fs into the kernel?
Click to expand...
Click to collapse
It's already included, I tested it just now with my actual Version via USB OTG a d could read and write. It should also work with the 20150212 Version.
regards,
lombartz
lombartz said:
It's already included, I tested it just now with my actual Version via USB OTG a d could read and write. It should also work with the 20150212 Version.
regards,
lombartz
Click to expand...
Click to collapse
Strange. My data and cache partition are f2fs and with the f4ktion cm11 kernel all is working well, but after installation of your kernel I'm stuck at the boot logo.
bongster said:
Strange. My data and cache partition are f2fs and with the f4ktion cm11 kernel all is working well, but after installation of your kernel I'm stuck at the boot logo.
Click to expand...
Click to collapse
Here is a Version without OC/UV or other tweaks but with all CM Updates. Its about 20% slower than the tweaked Version but more actual than the V20150212.
If this one boots your phone doesn't like my OC/UV settings...
lombartz said:
Here is a Version without OC/UV or other tweaks but with all CM Updates. Its about 20% slower than the tweaked Version but more actual than the V20150212.
If this one boots your phone doesn't like my OC/UV settings...
Click to expand...
Click to collapse
Thank you very much! I will test it and report back! If I understand it right, f2fs support is also in stock cm11 kernel?
I never tried it...
bongster said:
Thank you very much! I will test it and report back! If I understand it right, f2fs support is also in stock cm11 kernel?
I never tried it...
Click to expand...
Click to collapse
Yes.
lombartz said:
Yes.
Click to expand...
Click to collapse
No luck. I also tried flashing the latest cm11 nightly with no luck.
If I remember right I've tried the stock kernel some time ago only formatting the cache partition and this didn't work either.
20150212 working nice with latest Carbon 4.4.4
can you please add option to underclock min CPU to 162/270 MHz?
spixy said:
20150212 working nice with latest Carbon 4.4.4
can you please add option to underclock min CPU to 162/270 MHz?
Click to expand...
Click to collapse
This is a technically useless placebo feature and doesn' t save any energy.
The HFPLL has to be used to get the lower frequencys and this will eat the saved energy.
br,
lombartz
bongster said:
No luck. I also tried flashing the latest cm11 nightly with no luck.
If I remember right I've tried the stock kernel some time ago only formatting the cache partition and this didn't work either.
Click to expand...
Click to collapse
Hmm, the reason is the fstab.qcom, /cache and /data is expexted to be ext4.
Can be changed but I dont know how to allow both fs at the moment.
lombartz said:
This is a technically useless placebo feature and doesn' t save any energy.
The HFPLL has to be used to get the lower frequencys and this will eat the saved energy.
br,
lombartz
Click to expand...
Click to collapse
hi, I dont know what HFPLL is (some high frequency PLL), but I trust you
but still, is more battery efficient to hold wakelock with 162MHz than with 384, no? (see my previous post)
But on theother hand, 50mW diference between 162 and 384 MHz isnt realy so large...
spixy said:
hi, I dont know what HFPLL is (some high frequency PLL), but I trust you
but still, is more battery efficient to hold wakelock with 162MHz than with 384, no? (see my previous post)
But on theother hand, 50mW diference between 162 and 384 MHz isnt realy so large...
Click to expand...
Click to collapse
I suppose you mean 50 mV ? The lower UV limit is reached at about 384 MHz anyway.
Youre right with hfpll. Only at 384 MHz the CPU runs with pll8.
If you undervolt @ 384 manually as much as possible you will find that you cannot go noticeably lower if you clock down further.
At the Moment I am testing other tweaks that should be more effective an give some extra performance.
bongster said:
No luck. I also tried flashing the latest cm11 nightly with no luck.
If I remember right I've tried the stock kernel some time ago only formatting the cache partition and this didn't work either.
Click to expand...
Click to collapse
If you like to you can test this. But please make a full backup before because i did not test it myself. I don't want to reformat my phone for f2fs at the moment.
If it boots you are a tester for all the new changes ...
This Version will not run with ext4 /cache and /data partitions.
lombartz said:
If you like to you can test this. But please make a full backup before because i did not test it myself. I don't want to reformat my phone for f2fs at the moment.
If it boots you are a tester for all the new changes ...
This Version will not run with ext4 /cache and /data partitions.
Click to expand...
Click to collapse
Thank you very much!
After app optimisation the phone reboots and after the reboot it hangs at the Samsung logo. Only recovering the old boot image helps. Don't know if the oc is the reason.
Update:
I've tried oc with f4ction kernel and had also a reboot. I guess my CPU is not the best.
bongster said:
Thank you very much!
After app optimisation the phone reboots and after the reboot it hangs at the Samsung logo. Only recovering the old boot image helps. Don't know if the oc is the reason.
Update:
I've tried oc with f4ction kernel and had also a reboot. I guess my CPU is not the best.
Click to expand...
Click to collapse
I am sorry. Should not publish something I did not test myself...
What OC Values did you use with f4ction ?
lombartz said:
I am sorry. Should not publish something I did not test myself...
What OC Values did you use with f4ction ?
Click to expand...
Click to collapse
No problem. I'm aware of the issues that can happen.
Normally I use f4ction as it is with 50uv. For the test I oc'ed to 1998mhz.
I upgraded my Touchpad to Latest version of Nougat yesterday.
However as soon as I started loading a few basic apps it started to not respond at all & ends up having to be continually rebooted. It's slightly better now but still has to be rebooted every so often & very often locks up for 30-60 seconds at a time.
I've checked all available space on storage & appears to be all correct with what was in the instructions, plus this was a clean install (the upgrade from kitkat was even worse!) & was done via TWRP with latest ROM, GAPPS etc. I'm aware Nougat is not the finished article but judging by other comments on the forum their experience is somewhat better than mine (using the TP right now us very frustrating).
This is being installed on a 32mb TP so storage isn't an issue at all. I've done a number of upgrades over the last few years but this is the first time I've run into these sort of problems.
Any help or suggestions would be greatly appreciated.
Thanks
Dellboy17
Exact same issue i am also facing.if somebody installed a fluidic rom means tell me ivwill also follow.
What's a fluidic ROM?
Dellboy17 said:
What's a fluidic ROM?
Click to expand...
Click to collapse
i think they mean 'one that operates in a fluid (smooth) manner'. i also have this problem on most n rom's i've tried, but addmittedly, my touchpad is near nand exhaustion. (and something about the N setups i've tried exacerbates it)
Evervolv 7.1.x lag fix
Dellboy17 said:
I upgraded my Touchpad to Latest version of Nougat yesterday.
However as soon as I started loading a few basic apps it started to not respond at all & ends up having to be continually rebooted. It's slightly better now but still has to be rebooted every so often & very often locks up for 30-60 seconds at a time.
I've checked all available space on storage & appears to be all correct with what was in the instructions, plus this was a clean install (the upgrade from kitkat was even worse!) & was done via TWRP with latest ROM, GAPPS etc. I'm aware Nougat is not the finished article but judging by other comments on the forum their experience is somewhat better than mine (using the TP right now us very frustrating).
This is being installed on a 32mb TP so storage isn't an issue at all. I've done a number of upgrades over the last few years but this is the first time I've run into these sort of problems.
Any help or suggestions would be greatly appreciated.
Thanks
Dellboy17
Click to expand...
Click to collapse
Sivabalan said:
Exact same issue i am also facing.if somebody installed a fluidic rom means tell me ivwill also follow.
Click to expand...
Click to collapse
speakxj7 said:
i think they mean 'one that operates in a fluid (smooth) manner'. i also have this problem on most n rom's i've tried, but addmittedly, my touchpad is near nand exhaustion. (and something about the N setups i've tried exacerbates it)
Click to expand...
Click to collapse
Hey guys install Shumash's SKZ Kernel and apply the following changes below, your user experience should drastically improve.
Extras: SKZ-OC Kernel recommended for Evervolv 7.1.x
[KERNEL]SKZ Overclock Kernel for Evervolv [1836KHz CPU/320MHz GPU]
Install notes:
-Install the SKZ-Kernel by flashing this zip file here through TWRP recovery
-Remove the Kernel by flashing a Evervolv ROM with TWRP recovery
-Enable Root permissions by flashing this Supersu v2.46 zip here with TWRP recovery
-You will need to update the Superuser binaries once your system boots.
-Install the Kernel Adiutor app to Overclock your CPU here
Recommended settings:
Note: These settings should fix the lag and touchscreen issues.
CPU
Set on boot = on
CPU Maximum Frequency = 1728MHz
CPU Minimum Frequency = 648MHz
CPU Governor = smartmax or dancedance
Schedule workqueues on awake CPUs to save power = enabled
CPU Hotplug
IntelliPlug = enabled
GPU
Apply on boot = on
GPU 2D Maximum Frequency = 266MHz
GPU 3D Maximum Frequency = 320MHz
GPU Governor = simple
I/O Scheduler
Scheduler = enabled
Scheduler = tripndroid
Kernel Samepage Merging
Kernel Samepage Merging = enabled
Low Memory Killer
Adaptive Low Memory Killer = enabled
Profile = aggressive
Misc
TCP Congestion Algorithm = sociopath
RolandDeschain79 said:
--SNIP--
[KERNEL]SKZ Overclock Kernel for Evervolv [1836KHz CPU/320MHz GPU]
--SNIP--
Click to expand...
Click to collapse
Note that while you can download the most current kernel from the links given, the thread is no longer being updated.
Devs Base note in the OP
shumash said:
Note that while you can download the most current kernel from the links given, the thread is no longer being updated.
Click to expand...
Click to collapse
Would it be possible to mention this in the OP of your old thread? Every time I add links to devs base the mods remove it here at XDA :silly:
Edit: Also worth mentioning that increasing the min CPU frequency to 600+ will help with the Evervolv lag issues.
Info about the move to Devs base for all those who haven't heard.
RolandDeschain79 said:
Would it be possible to mention this in the OP of your old thread? Every time I add links to devs base the mods remove it here at XDA :silly:
Edit: Also worth mentioning that increasing the min CPU frequency to 600+ will help with the Evervolv lag issues.
Info about the move to Devs base for all those who haven't heard.
Click to expand...
Click to collapse
wilco
speakxj7 said:
i think they mean 'one that operates in a fluid (smooth) manner'. i also have this problem on most n rom's i've tried, but addmittedly, my touchpad is near nand exhaustion. (and something about the N setups i've tried exacerbates it)
Click to expand...
Click to collapse
Yes correct!!
---------- Post added at 11:02 PM ---------- Previous post was at 10:57 PM ----------
RolandDeschain79 said:
Hey guys install Shumash's SKZ Kernel and apply the following changes below, your user experience should drastically improve.
Extras: SKZ-OC Kernel recommended for Evervolv 7.1.x
[KERNEL]SKZ Overclock Kernel for Evervolv [1836KHz CPU/320MHz GPU]
Install notes:
-Install the SKZ-Kernel by flashing this zip file here through TWRP recovery
-Remove the Kernel by flashing a Evervolv ROM with TWRP recovery
-Enable Root permissions by flashing this Supersu v2.46 zip here with TWRP recovery
-You will need to update the Superuser binaries once your system boots.
-Install the Kernel Adiutor app to Overclock your CPU here
Recommended settings:
Note: These settings should fix the lag and touchscreen issues.
CPU
Set on boot = on
CPU Maximum Frequency = 1728MHz
CPU Minimum Frequency = 648MHz
CPU Governor = smartmax or dancedance
Schedule workqueues on awake CPUs to save power = enabled
CPU Hotplug
IntelliPlug = enabled
GPU
Apply on boot = on
GPU 2D Maximum Frequency = 266MHz
GPU 3D Maximum Frequency = 320MHz
GPU Governor = simple
I/O Scheduler
Scheduler = enabled
Scheduler = tripndroid
Kernel Samepage Merging
Kernel Samepage Merging = enabled
Low Memory Killer
Adaptive Low Memory Killer = enabled
Profile = aggressive
Misc
TCP Congestion Algorithm = sociopath
Click to expand...
Click to collapse
Thanks buddy!! Actually fed up with the lag issue I have reverted to milaq's kikat 4.4.4. . Tonight will revert back to evervolv and will update here.
One doubt as the min cpu freq is 648 mhz will it not eat in to the battery??
Thanks,
Sivbal.
Sivabalan said:
Yes correct!!
---------- Post added at 11:02 PM ---------- Previous post was at 10:57 PM ----------
Thanks buddy!! Actually fed up with the lag issue I have reverted to milaq's kikat 4.4.4. . Tonight will revert back to evervolv and will update here.
One doubt as the min cpu freq is 648 mhz will it not eat in to the battery??
Thanks,
Sivbal.
Click to expand...
Click to collapse
Have flashed the latest test build and applied the above settings . its better now . will report after some days of usage.
Thanks for testing
Sivabalan said:
Have flashed the latest test build and applied the above settings . its better now . will report after some days of usage.
Click to expand...
Click to collapse
Thanks for testing it out and reporting back:highfive: I've found the battery drain is only slightly higher but fixing some of the lagging is worth the trade off.
RolandDeschain79 said:
Thanks for testing it out and reporting back:highfive: I've found the battery drain is only slightly higher but fixing some of the lagging is worth the trade off.
Click to expand...
Click to collapse
Also in toolbox if I disable aosp mode,the touchpad become very laggy and YouTube is not at all responding. But if we enbale aosp mode and disable all toolsbox functions...touchpad is useable.
Guys now after a long time I formatted my data and all the partitions then installed the evervolv 7.1.2 test build. Skz kernel overclocked to 1728. Also gpu overcolcked to 320. Kernel samepage killing enabled.cpu profile set to interactive. The rom is performing good. Please try.
Sent from my Touchpad using Tapatalk
---------- Post added at 09:56 AM ---------- Previous post was at 09:49 AM ----------
shumash said:
Note that while you can download the most current kernel from the links given, the thread is no longer being updated.
Click to expand...
Click to collapse
Guys now after a long time I formatted my data and all the partitions then installed the evervolv 7.1.2 test build. Skz kernel overclocked to 1728. Also gpu overcolcked to 320. Kernel samepage killing enabled.cpu profile set to interactive. The rom is performing good. Please try.
Sent from my Touchpad using Tapatalk
Is this much better than the Android 6 builds? The last decent one I had was JCSullins 5.1, my current 6.0.1 (22/08/2016) takes 2-3 longer to start up, is noticeably slow/laggy and has no USB OTG support. I notice that the Android 7 builds have no camera, Bluetooth and I need to overclock to have a good experience? I might go back to 5.1 again...
theronkinator said:
Is this much better than the Android 6 builds? The last decent one I had was JCSullins 5.1, my current 6.0.1 (22/08/2016) takes 2-3 longer to start up, is noticeably slow/laggy and has no USB OTG support. I notice that the Android 7 builds have no camera, Bluetooth and I need to overclock to have a good experience? I might go back to 5.1 again...
Click to expand...
Click to collapse
The newer evervolv builds have both working camera and Bluetooth but yes I'd recommend getting shumash's kernel and overclocking for the best experience. However if you're already using CM12 try updating to Milaqs latest builds here It might fix the issues you're having. I generally find Milaqs CM11 to be the most stable rom for your daily driver. Let me know how the newer builds of CM12 workout for you.
RolandDeschain79 said:
The newer evervolv builds have both working camera and Bluetooth but yes I'd recommend getting shumash's kernel and overclocking for the best experience. However if you're already using CM12 try updating to Milaqs latest builds here It might fix the issues you're having. I generally find Milaqs CM11 to be the most stable rom for your daily driver. Let me know how the newer builds of CM12 workout for you.
Click to expand...
Click to collapse
Thanks, I'm just deciding whether to go with JCSullins 12.1 from Jan 2016 or Milaq's 12.0 from Aug 2017. Tempted to go for 12.1 even though the actual rom is much older, I don't think much could have changed.
RolandDeschain79 said:
Hey guys install Shumash's SKZ Kernel and apply the following changes below, your user experience should drastically improve.
[...]
Misc
TCP Congestion Algorithm = sociopath
Click to expand...
Click to collapse
Thx a lot !! It saved my HPTP.
Yesterday i flashed the last evervolv, and looked for some improvements on xda-dev, and I saw your post. After flashing, I tried to apply these settings.
What a change !! The TouchPad is now usable.
My plan is to use it (with the touchstone) as a screen for my home automation. It was impossible, but now it seems to be responsive enough !
Thanks again.