SGH-I537 AT&T
1. Phone is never seen by or connects to Kies, just stays at Connecting. USB drivers are installed, and when connected to PC you get device connection tone, but phone is not seen in My Computer like normal.
When I enter the Model # SGH-I537 and the SN#, it comes back with...Please check the model name and enter it. Or it connects and message comes back from Samsung saying something like it can't verify the phone. For some stupid reason I can't find the latest official firmware for my phone 4.4.2, all I can find is 4.2.2.
Someone told me if you flash using Odin that you need to flash with the same firmware that is currently on your phone. I also hate to use Odin as I've heard of so many people bricking their phone with Odin. I'm not sure what's available for the I537, but once when I bricked my S2, I was able to connect a USB jig that shorted a couple of the pins, and this allowed me to boot into recovery. I wish I had something this simple of my S4 Active.
I'm in a bad way, I sold this phone, so I went into recovery to do wipe and reset the phone to factory, wipe was successful, but when rebooted it would only boot to Download mode. So then I tried to use Kies, and with Kies I never actually got into recovery, then the next time I rebooted, it went the Firmware upgrade encountered an issue for Kies, and is currently stuck there. I listed the phone online for sale and was purchased overnight. Now I have a phone that is worthless in its current state. Phone was only rooted, its never had anything else on it but stock firmware. I rooted it to use battery savers and get rid of some of the bloat.
I at updated it OTA to 4.4.2, and then rooted with towel. I tried to used Odin to push 4.3 I got off XDA official firmware, but that just failed. Anyone have an bright ideas? Help Please ! ! !
Log:
<ID:0/004> Removed!!
<ID:0/004> Added!!
<ID:0/004> Removed!!
<ID:0/004> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> BL_I537UCUBML2_2244695_REV06_user_low_ship_MULTI_CERT.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> AP_I537UCUBML2_2244695_REV06_user_low_ship_MULTI_CERT.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> CP_I537UCUBML2_2244695_REV06_user_low_ship_MULTI_CERT.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> CSC_ATT_I537ATTBML2_2244695_REV06_user_low_ship_MULTI_CERT.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/004> Odin v.3 engine (ID:4)..
<ID:0/004> File analysis..
<ID:0/004> SetupConnection..
<ID:0/004> Initialzation..
<ID:0/004> Set PIT file..
<ID:0/004> DO NOT TURN OFF TARGET!!
<ID:0/004> Get PIT for mapping..
<ID:0/004> Firmware update start..
<ID:0/004> SingleDownload.
<ID:0/004> sbl1.mbn
<ID:0/004> NAND Write Start!!
<ID:0/004> sbl2.mbn
<ID:0/004> sbl3.mbn
<ID:0/004> rpm.mbn
<ID:0/004> aboot.mbn
<ID:0/004> FAIL! (Auth)
<ID:0/004>
<ID:0/004> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
HC1Gunner said:
SGH-I537 AT&T
1. Phone is never seen by or connects to Kies, just stays at Connecting. USB drivers are installed, and when connected to PC you get device connection tone, but phone is not seen in My Computer like normal.
When I enter the Model # SGH-I537 and the SN#, it comes back with...Please check the model name and enter it. Or it connects and message comes back from Samsung saying something like it can't verify the phone. For some stupid reason I can't find the latest official firmware for my phone 4.4.2, all I can find is 4.2.2.
Someone told me if you flash using Odin that you need to flash with the same firmware that is currently on your phone. I also hate to use Odin as I've heard of so many people bricking their phone with Odin. I'm not sure what's available for the I537, but once when I bricked my S2, I was able to connect a USB jig that shorted a couple of the pins, and this allowed me to boot into recovery. I wish I had something this simple of my S4 Active.
I'm in a bad way, I sold this phone, so I went into recovery to do wipe and reset the phone to factory, wipe was successful, but when rebooted it would only boot to Download mode. So then I tried to use Kies, and with Kies I never actually got into recovery, then the next time I rebooted, it went the Firmware upgrade encountered an issue for Kies, and is currently stuck there. I listed the phone online for sale and was purchased overnight. Now I have a phone that is worthless in its current state. Phone was only rooted, its never had anything else on it but stock firmware. I rooted it to use battery savers and get rid of some of the bloat.
I at updated it OTA to 4.4.2, and then rooted with towel. I tried to used Odin to push 4.3 I got off XDA official firmware, but that just failed. Anyone have an bright ideas? Help Please ! ! !
Log:
<ID:0/004> Removed!!
<ID:0/004> Added!!
<ID:0/004> Removed!!
<ID:0/004> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> BL_I537UCUBML2_2244695_REV06_user_low_ship_MULTI_CERT.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> AP_I537UCUBML2_2244695_REV06_user_low_ship_MULTI_CERT.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> CP_I537UCUBML2_2244695_REV06_user_low_ship_MULTI_CERT.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> CSC_ATT_I537ATTBML2_2244695_REV06_user_low_ship_MULTI_CERT.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/004> Odin v.3 engine (ID:4)..
<ID:0/004> File analysis..
<ID:0/004> SetupConnection..
<ID:0/004> Initialzation..
<ID:0/004> Set PIT file..
<ID:0/004> DO NOT TURN OFF TARGET!!
<ID:0/004> Get PIT for mapping..
<ID:0/004> Firmware update start..
<ID:0/004> SingleDownload.
<ID:0/004> sbl1.mbn
<ID:0/004> NAND Write Start!!
<ID:0/004> sbl2.mbn
<ID:0/004> sbl3.mbn
<ID:0/004> rpm.mbn
<ID:0/004> aboot.mbn
<ID:0/004> FAIL! (Auth)
<ID:0/004>
<ID:0/004> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
Click to expand...
Click to collapse
Kies does not work with the i537, AT&T will not allow Samsung to release any of the firmware. You have nothing to worry about though, all you need to do is put the phone in download mode and use Odin to flash the ML2 package. MAKE SURE YOU DO NOT LOAD THE BOOTLOADER IN ODIN, IT WILL FAIL TO FLASH. Flash the other 3 files in Odin, reboot the phone to stock recovery and flash the NE3 OTA.
You're fine, it'll be in working condition by the end of the night.
Sounds Positive
Devo7v said:
Kies does not work with the i537, AT&T will not allow Samsung to release any of the firmware. You have nothing to worry about though, all you need to do is put the phone in download mode and use Odin to flash the ML2 package. MAKE SURE YOU DO NOT LOAD THE BOOTLOADER IN ODIN, IT WILL FAIL TO FLASH. Flash the other 3 files in Odin, reboot the phone to stock recovery and flash the NE3 OTA.
You're fine, it'll be in working condition by the end of the night.
Click to expand...
Click to collapse
Thanks for you help on this holiday weekend! I will give this a try tomorrow and cross my fingers. I was able to download the ML2 package, but I'm not sure about the NE3 OTA, I'm getting a lot of different hits when I do a search for it. Could you possible reply back with a link? I not sure what NE3 is, was that an update? I basically want to leave the phone stock for the new owner. Or are you saying that the ML2 flash will fix my phone, and after I have successfully booted my phone, I can go into settings/about phone/ software update, and this will give me NE3 OTA?
I see two different files:
ML2 to NE3 OTA File 444 MB
NC9 to NE3 OTA File 66.4 MB
BTW, I read somewhere in a post that if you are going to run/use odin, then you can not have Kies installed on your PC, any truth to this?
HC1Gunner said:
Thanks for you help on this holiday weekend! I will give this a try tomorrow and cross my fingers. I was able to download the ML2 package, but I'm not sure about the NE3 OTA, I'm getting a lot of different hits when I do a search for it. Could you possible reply back with a link? I not sure what NE3 is, was that an update? I basically want to leave the phone stock for the new owner. Or are you saying that the ML2 flash will fix my phone, and after I have successfully booted my phone, I can go into settings/about phone/ software update, and this will give me NE3 OTA?
I see two different files:
ML2 to NE3 OTA File 444 MB
NC9 to NE3 OTA File 66.4 MB
BTW, I read somewhere in a post that if you are going to run/use odin, then you can not have Kies installed on your PC, any truth to this?
Click to expand...
Click to collapse
I've never heard about the Kies / Odin issue, although that doesn't mean it's not true in certain cases.
NE3 is the latest firmware, you mentioned you were already on 4.4.2, so this will ensure that you're back on 4.4.2, and should fix some of the bugs with the original 4.4.2 OTA that was pushed a couple months ago.
The 2 OTA files you referenced are for updating from different firmware. So since your phone will be on ML2 and you're going to update it to NE3, you need to download the 444MB file and flash it through stock recovery.
Related
Hi so about a week ago I flashed the 2.3.3 gingerbread bootloaders and stock gingerbread rom using this method: http://forum.xda-developers.com/showthread.php?t=1045734
Then I flashed GR-11, then Continuum v5.3, and then Perception II Beta 3. Then I decided to flash back to stock 2.1 using Odin one click. But now I want to flash the 2.3.3 bootloaders and gingerbread stock rom again by using the same method (http://forum.xda-developers.com/showthread.php?t=1045734), but now everytime i try to reflash them, it fails.
this is what odin says specifically: <ID:0/004> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> PDA_XWJVB_Sbl.tar.md5 is valid.
<OSM> PHONE_XXJVK.tar.md5 is valid.
<OSM> CSC_NEE_JV3.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/004> Odin v.3 engine (ID:4)..
<ID:0/004> File analysis..
<ID:0/004> SetupConnection..
<ID:0/004> Initialzation..
<ID:0/004> Set PIT file..
<ID:0/004> DO NOT TURN OFF TARGET!!
<ID:0/004> Re-Partition operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
Can anyone help? I tried searching for this but could not find it so sorry if there is another thread about this :\
make sure "repartition" is selected" ?
Yes I did that I followed the directions from the link exactly. Am i supposed to pull out the sim card or something?
Just wondering - did you have the phone in download mode?
When i had it plugged into odin, yeah. My phone doesnt have the 3 button fix so i had to use adb reboot download and then i disconnected it and opened odin and plugged it back in. Should i just use my jig to put it into download mode instead of using adb because that could interrupt it or something?
Switch usb ports on your pc, make sure it's on the back connected to the motherboard, not a front port our a hub.
I tried that too with no luck :'(
hi,
well i have a galaxy gear v700, and i tryed to flash it before but i couldnt do well, after it i think it has a brick . but using this tutorial http://forum.xda-developers.com/showthread.php?t=2776157 i give my watch a new life, now i want to upgrade to tizen and i cant, kies tell me that the firmware was modify and no upgrade avable, and when i try to put a rom odin doesnt load, and stop on the last point that i show here what can i do to upgrade to tizen
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> kernel-GB-3a.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Firmware update start..
<ID:0/003> zImage
my Smart Watch Bloked
samsung tizen not responding
sir,
i own a samsung tizen z1 ,the device is not responding only logo sign is shown, i decided to flash it but md5 bootloader is locked so not able to flash -using odin software i need bootloader file to flash it and unlock it.. plz help
radekamilo said:
hi,
well i have a galaxy gear v700, and i tryed to flash it before but i couldnt do well, after it i think it has a brick . but using this tutorial http://forum.xda-developers.com/showthread.php?t=2776157 i give my watch a new life, now i want to upgrade to tizen and i cant, kies tell me that the firmware was modify and no upgrade avable, and when i try to put a rom odin doesnt load, and stop on the last point that i show here what can i do to upgrade to tizen
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> kernel-GB-3a.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Firmware update start..
<ID:0/003> zImage
Click to expand...
Click to collapse
So I'm trying to root my SM-G925I on 6.0.1 using Auto-Root and Odin. I got the right file, the latest odin. Put my phone into download, it registers on odin. Load it on AP and hit start. Then, I get this
<ID:0/003> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Odin engine v(ID:3.1203)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Can't open the serial(COM) port.
<OSM> All threads completed. (succeed 0 / failed 1)
And it obviously fails. Any suggestions?
EDIT: Now it gets stuck at "Get PIT for mapping..."
Probably because you aren't suppose to use any version of Odin for the S6 except "Odin3_v3.10.6"
Maqical said:
Probably because you aren't suppose to use any version of Odin for the S6 except "Odin3_v3.10.6"
Click to expand...
Click to collapse
Hmmm...Just tried with that version and it gets stuck on Get PIT for Mapping. Any other suggestions? Thanks.
Thanks! It worked when I switched computer.
Had some issue during flashing, and the process got interrupted.
Now the phone is stuck on "An error has occured while updating the device software", can't get in to recovery or download mode.
Any advice would be appreciated.
Thanks.
k10n9 said:
Had some issue during flashing, and the process got interrupted.
Now the phone is stuck on "An error has occured while updating the device software", can't get in to recovery or download mode.
Any advice would be appreciated.
Thanks.
Click to expand...
Click to collapse
keep pressing on volume down and power and insert cable to get bootloader mode again
carlitobahsoun said:
keep pressing on volume down and power and insert cable to get bootloader mode again
Click to expand...
Click to collapse
it just keeps going back to this screen ""An error has occured while updating the device software""
k10n9 said:
it just keeps going back to this screen ""An error has occured while updating the device software""
Click to expand...
Click to collapse
ok ,repeat : once screen black , keep pressing volume up + key power and insert cable
dont panic , happend to me dont worry
thanks. managed to get it to download mode.
another issue arise, trying to flash via odin again but it says <ID:0/004> Re-Partition operation failed.
k10n9 said:
thanks. managed to get it to download mode.
another issue arise, trying to flash via odin again but it says <ID:0/004> Re-Partition operation failed.
Click to expand...
Click to collapse
than u are flashing uncorrect firmware....show me what firmware u are and what are u trying to flash
And u have to make sure u have repartition unchecked in odin
carlitobahsoun said:
than u are flashing uncorrect firmware....show me what firmware u are and what are u trying to flash
Click to expand...
Click to collapse
G998U1_XAA to G991U_TMB
sswagonman said:
And u have to make sure u have repartition unchecked in odin
Click to expand...
Click to collapse
repartition is unchecked
you cant flash s21 firmware to a s21 ultra
k10n9 said:
G998U1_XAA to G991U_TMB
Click to expand...
Click to collapse
What exactly are you trying to do? Flashing G998 to G991? Is that a mistype or are you actually trying to flash a different device firmware on your phone?
jerrycoffman45 said:
you cant flash s21 firmware to a s21 ultra
Click to expand...
Click to collapse
It's s21 ultra firmware:
Samsung Galaxy S21 5G Firmware Download SM-G991U Free Download
Samsung Galaxy S21 5G Firmware Download SM-G991U Free Download ⭐ Official and fast update ⭐ Max speed and free download ⭐ Best Samsung Galaxy website
samfw.com
enigmaamit said:
What exactly are you trying to do? Flashing G998 to G991? Is that a mistype or are you actually trying to flash a different device firmware on your phone?
Click to expand...
Click to collapse
I was having the VoLTE issue, and wanted to try this:
VoLTE not working since OneUI 4.0 Beta installation
Hello All, I posted this in Samsung Community, but unfortunately none was able to help. I am hoping XDA members could help fix this issue. I am facing a strange problem with my S21 Ultra Unlocked which was directly bought from Samsung. I had...
forum.xda-developers.com
no G991U_TMB is s21 firmware you need g998u or g998u1 firmware
G998U and G998U1 Firmware Links and Flashing Discussion Here
For those who aren't already aware, G998U is the model number of all of the US carrier versions of the S21 Ultra. The G998U1 is the model number of the same device, but sold by Samsung SIM unlocked and with no carrier bloatware. Firmware is 100%...
forum.xda-developers.com
jerrycoffman45 said:
no G991U_TMB is s21 firmware you need g998u or g998u1 firmware
G998U and G998U1 Firmware Links and Flashing Discussion Here
For those who aren't already aware, G998U is the model number of all of the US carrier versions of the S21 Ultra. The G998U1 is the model number of the same device, but sold by Samsung SIM unlocked and with no carrier bloatware. Firmware is 100%...
forum.xda-developers.com
Click to expand...
Click to collapse
ok. let me try again
Hi all,
I really need some help. I bricked my S21 Ultra. I bought it in Thailand and wanted to change it to German CSC. And it now shows on the screen "an error occured while updating the sofware".
Frst in red it was saying something ike
Hash of Data Does Not Match Digest in DescriptorNow it only says "DEBORE :" nothing behind it....
I tried installing HOME_CSC_OXM_G998BOXM4BULI from HOME_CSC_OXM_G998BOXM4BVB1 (I entered all 4 flles in ODIN, ticked only Auto_Reboot and F.Rest Time ticked.
I cannot restart it or shut it off. It always come back to that screen.
Can anyone help?
In future you'll find that the error has occured screen is actually download mode it just displays a different screen. If you plug your phone in it registers and flashes fine from that screen.
GeeAyeZee said:
In future you'll find that the error has occured screen is actually download mode it just displays a different screen. If you plug your phone in it registers and flashes fine from that screen.
Click to expand...
Click to collapse
But I cannot flash with odin, I cannot go back anywhere (e.g. Factory Reset). What can I do? Do you have an Idea? Smart Switch does not have the recovery option...
those are the error messages in ODIN:
<ID:0/004> Removed!!
<ID:0/004> Removed!!
<ID:0/004> Added!!
<ID:0/004> Removed!!
<ID:0/004> Added!!
<ID:0/004> Removed!!
<ID:0/004> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/004> Odin engine v(ID:3.1401)..
<ID:0/004> File analysis..
<ID:0/004> skip file list for home binary
<ID:0/004> userdata.img
<ID:0/004> misc.bin
<ID:0/004> Home Binary Download
<ID:0/004> Total Binary size: 10626 M
<ID:0/004> SetupConnection..
<ID:0/004> Initialzation..
<ID:0/004> Get PIT for mapping..
<ID:0/004> Firmware update start..
<ID:0/004> NAND Write Start!!
<ID:0/004> SingleDownload.
<ID:0/004> sboot.bin
<ID:0/004> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
<ID:0/004> Removed!!
<ID:0/004> Removed!!
<ID:0/004> Added!!
Alex_Muc said:
those are the error messages in ODIN:
<ID:0/004> Removed!!
<ID:0/004> Removed!!
<ID:0/004> Added!!
<ID:0/004> Removed!!
<ID:0/004> Added!!
<ID:0/004> Removed!!
<ID:0/004> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/004> Odin engine v(ID:3.1401)..
<ID:0/004> File analysis..
<ID:0/004> skip file list for home binary
<ID:0/004> userdata.img
<ID:0/004> misc.bin
<ID:0/004> Home Binary Download
<ID:0/004> Total Binary size: 10626 M
<ID:0/004> SetupConnection..
<ID:0/004> Initialzation..
<ID:0/004> Get PIT for mapping..
<ID:0/004> Firmware update start..
<ID:0/004> NAND Write Start!!
<ID:0/004> SingleDownload.
<ID:0/004> sboot.bin
<ID:0/004> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
<ID:0/004> Removed!!
<ID:0/004> Removed!!
<ID:0/004> Added!!
Click to expand...
Click to collapse
make sure you get the latest firmware using frija and delete then reinstall latest drivers from samsung. use a different cable perhaps and a usb 2.0 port. If your quick you can access download mode by inserting the cable just as the phone reboots from button combo
GeeAyeZee said:
make sure you get the latest firmware using frija and delete then reinstall latest drivers from samsung. use a different cable perhaps and a usb 2.0 port. If your quick you can access download mode by inserting the cable just as the phone reboots from button combo
Click to expand...
Click to collapse
forget smart switch its useless
I tried to root my phone today and I failed and my phone is not working right now. Does anybody know how to fix it? Can someone please help me? Please!!! Thank you so much.
hxsports said:
I tried to root my phone today and I failed and my phone is not working right now. Does anybody know how to fix it? Can someone please help me? Please!!! Thank you so much.
Click to expand...
Click to collapse
My phone current is look like this. And I tried Odin flash and the process is failed.
<ID:0/004> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/004> Odin engine v(ID:3.1401)..
<ID:0/004> File analysis..
<ID:0/004> Total Binary size: 332 M
<ID:0/004> SetupConnection..
<ID:0/004> Initialzation..
<ID:0/004> Set PIT file..
<ID:0/004> DO NOT TURN OFF TARGET!!
<ID:0/004> Get PIT for mapping..
<ID:0/004> Firmware update start..
<ID:0/004> NAND Write Start!!
<ID:0/004> SingleDownload.
<ID:0/004> abl.elf
<ID:0/004> xbl.elf
<ID:0/004> FAIL! (Auth)
<ID:0/004>
<ID:0/004> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
hxsports said:
My phone current is look like this. And I tried Odin flash and the process is failed.
<ID:0/004> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/004> Odin engine v(ID:3.1401)..
<ID:0/004> File analysis..
<ID:0/004> Total Binary size: 332 M
<ID:0/004> SetupConnection..
<ID:0/004> Initialzation..
<ID:0/004> Set PIT file..
<ID:0/004> DO NOT TURN OFF TARGET!!
<ID:0/004> Get PIT for mapping..
<ID:0/004> Firmware update start..
<ID:0/004> NAND Write Start!!
<ID:0/004> SingleDownload.
<ID:0/004> abl.elf
<ID:0/004> xbl.elf
<ID:0/004> FAIL! (Auth)
<ID:0/004>
<ID:0/004> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
Click to expand...
Click to collapse
My phone stuck in Download mode right now and it shows
partition vbmeta
Reason vbmeta: Error verifying vbmeta image:
0_0INDIVLDUMT_EDRHS_IMTHSGAUEMSAC
if your phone won't boot because of verified boot, either flash back to stock or flash vbmeta_disabled.tar
if you tried to patch your boot.img this wouldn't really be a problem because magisk patches vbmeta for you when you patch.
if you tried to flash a magisk zip you should have followed instructions for twrp which requires flashing vbmeta_disable.tar in Odin. in other words you couldn't have followed instructions.
hxsports said:
I tried to root my phone today and I failed and my phone is not working right now. Does anybody know how to fix it? Can someone please help me? Please!!! Thank you so much.
Click to expand...
Click to collapse
bootloader is locked!! You got a US phone version, you can not Root neither install a custom Rom or TWRP.
Download the last official Rom for your phone, and flash it through Odin. Then your phone will work again.
3mel said:
if your phone won't boot because of verified boot, either flash back to stock or flash vbmeta_disabled.tar
if you tried to patch your boot.img this wouldn't really be a problem because magisk patches vbmeta for you when you patch.
if you tried to flash a magisk zip you should have followed instructions for twrp which requires flashing vbmeta_disable.tar in Odin. in other words you couldn't have followed instructions.
Click to expand...
Click to collapse
I can't flash anything into it because it say OEM lock and
hxsports said:
I can't flash anything into it because it say OEM lock and
Click to expand...
Click to collapse
flash the correct stock firmware for your phone and nothing else. if you have an American FE there's NOTHING ELSE that will work on it.
3mel said:
flash the correct stock firmware for your phone and nothing else. if you have an American FE there's NOTHING ELSE that will work on it.
Click to expand...
Click to collapse
Correct. There are sites, from where you may download the last available firmware for your phone!
Download it and flash it correctly with Odin, and it will work.
Download SM-G781U1 / Galaxy S20 Fan Edition 5G SM-G781U1 XAA in Samfw - Samsung firmware download
SM-G781U1 / Galaxy S20 Fan Edition 5G SM-G781U1 XAA samsung firmware download all model, lastest, fast update, completely free and fast speed in Samfw.com ✅
samfw.com
Download the latest one for US version for this phone, currently they jumped to bootloader v.7
Carreful, I gave you a link for S20 FE 5G !! If you got S20 FE 4G, download the adequate one.