Database Develop

Dead

I let my phone battery die, and now I can't turn it on.
Usually I get a red light which goes when the battery is in if its charging.
Sometimes I get a red light even when the battery is in and its charging.
If I do a soft reset, sometimes I get a flashing red light on the sides but then nothing.
I managed to get it back briefly by doing all manner of hard resets and soft resets, and taking the battery out and putting it back in over and over again for about half an hour...
Then I left it charging for half an hour or so and carelessly allowed the battery to die again because I needed to take it with me somewhere - so the same thing has happened again.
I left it charging overnight but I'm not having any luck with it this morning... any help would be much appreciated.

yeah similar problem here. my phone warned me the battery was low... i ignored the warning and used it until it died completely. then it wouldn't turn on. it was late so i just plugged it into the wall charger that came with the phone. i dont think it charged cause in the morning it was still flat. if anything i think having it connected to the charger while not charging drained the last a few drops of juice out of it. had a number of confusing red lights coming up in different spots at different times.
i read on here some guy managed to charge it by getting 3 AA batteries and connecting them directly to the battery for a couple of minuets. i did this and managed to turn the phone on! hoooray!
it had 1% and died in less than a couple of minuets even though i had it on the charger. tried the 3 AA battery trick again but to no avail. i think my battery is dead.
i'm pretty certain i will need to get a new one. i hope you are able to get yours working without buying a new battery.
im really annoyed the Sony Erricson batteries work out to be close to $100 AU. i would prefer to get a legit one... but does anyone have any experience with unofficial batteries? are they any good?

Sorry you're in the same boat... Ericsson really should have made this phone so that it can run out of battery.
Interesting - tell me more about the 3 AA battery trick!

sounds like the cells in your battery isnt balancing hence its dying...think you'll need to buy another one / or at least try another one to make sure it is and not the phone...

Hmmm... I fiddled and pressed buttons and took out the charger and put it in, and then kept pressing the on button while I was doing something else...
Suddenly it made the click noise, but it's not back yet.
It seems to have crashed on the 'Sony Ericsson' start up screen with the green logo.
I don't know if it's charging or not, so I'm not sure whether to turn it off to try again (at the risk of losing the battery), or leave it to charge as it is before I turn it off and can't start it again....
At least it's progress

There are a couple vof threads with many solutions. Look for them, they are very useful.

Yeah I've found a few - Thanks... just nothing they mentioned has worked yet
I think the problem I have may be a slightly different now anyway...
Now, if I unplug it I can't turn it on, but if it's plugged into my computer cable I can get it (every time - after about 3 minutes) to go to the Sony Ericsson loading screen but no further (as if there is no hard reset file for it to load). I can do that by plugging it in, then doing a soft reset (which produces flashing lights on the side) then holding on until it clicks (usually trying that a few times). When it clicks the lights on the side flash and it looks like it charges for a second before the lights go off and its just hte loading screen. I left it for 5 minutes and it turned off completely. Nothing happens if it's plugged into the wall cable at all.
Have you any idea how I might be able be get something to load after the loading screen?... Or any thoughts as to whether you think it's likely to be charging when its on that screen?
Thanks

Hmm... It seems you have a software problem as well.
Here is what I would do: get another battery (fully charged) and try one of these hard reset methods:
http://forum.xda-developers.com/showthread.php?t=437607
Something should work...

Sweet - I managed to get the hard reset screen to ask me the question about going back to factory defaults... after that the lights on the side are coming on to show its charging....
I guess there's a chance that when the battery is charged it'll have the juice to get past the loading screen... I hope anyway.

Wow this title gave me a heart attack almost
i thought someone is dead

plz i need help
hello good day plz i neesd to flash my htc p3600 and sony ericcson cybershot i need a software i can use to flash them plz help me any body that has an idea

just ordered a 1800mAh mugen power replacement battery. should be here in about a week my old SE k800i will be getting a bit of a work out in the mean time.
i think this break from unnecessary technology which I'm far too attached to will do me good. I'm far too materialistic.
hope you manage to get your battery going again!

My xperia doesn't take the charge!

Hey, dunno if some one had the same problem but my xperia doesn't take the charge.
Its appened when the mobile has terminated all his battery, and know the charge is not accepted by the phone
help me please

Something perhaps similar happened to me, i ran my battery completely flat and then could not switch the phone on even when it was on the charger. So I left it on the charger for ~1 hour and then it switched on fine! The other possibility is that you battery is dead. Hope this helps!

Its not the first time its appened to me, and the first time i had the problem i try a lot of time to recharge it, take out the battery, replace it etc.. and its worked.
But in 2 days, my phone is off :/
My battery is not dead i know, but how to recharge it

I have 2 computers from which I load it with usb cable. For some reason Mac Pro doesn't load the damn phone but Macbook does.
Try switching your "power" source. And sometimes when the battery goes really flat it needs many hours to even boot when loading up. One time I really thought the damn thing was dead for sure... But it came back to life
When you press the power button there's a red light next to volume buttons indicating it doesn't have enough power yet to boot up. If there's no red light then it's not charging at all.

thD64 said:
Hey, dunno if some one had the same problem but my xperia doesn't take the charge.
Its appened when the mobile has terminated all his battery, and know the charge is not accepted by the phone
help me please
Click to expand...
Click to collapse
Just leave if plugged-in and it will charge. It takes some time before it will charge if it is fully drained.

Ok thanks for reply
Have no real solution, but have the red light near to the volume button, or in the top of the phone.
But the phone doesn't take the charge at all...
The red light gave the battery charge, only that... have it sometimes and sometimes havent it...
Help me please
2 day less my phone know..

Ok i dunno why but the phone weak UP !
NICE
Ir was connected to the cpu and i presszs the button and it weak up
omg this phone

(Sort of) got it.
I'm not really an xda developer but id do have an xperia.
The same problem occured to my device about three weeks ago. I've noticed that the phone would still charge in the computer, but not by the power net adapter. (it must be broke i guess)
Today i've locked myself out calling the battery flat. I couldnt get it on anymore. After a lot of hassle this was the solution for me:
1) Connect the phone to a computer. Don't try to turn it on! Leave it there for about 15 minutes.
2) Disconnect the phone and pull out the battery.
3) Hold down the "on" button while inserting the battery back.
-- It should turn on now
4) Release the on button and quickly connect it to your computer again.
Hope this helps.

I just remember the red led lit on at the on/off button and the red light disappeared after 5 mins or so and i left for breakfast while it was still in the charger and by the time im back from breakfast, it turned itself on and was charging up

[Q] Will not charge or boot

My phone was running fine a few hours ago and I drained the battery. Now it will not charge or boot, no white or green light, and it is unresponsive to side buttons any ideas?

Try to plug the charger in while hitting the recovery combination without pressing the power button, does stuff show up?
Sent from my liquid glowing bomb shell

Nope
SuicideFlasher said:
Try to plug the charger in while hitting the recovery combination without pressing the power button, does stuff show up?
Sent from my liquid glowing bomb shell
Click to expand...
Click to collapse
Would be nice if that worked; was using a old BB charger (all that I had at the time). Still dont have the motorola charger but have a samsung charger at 1500mA instead of 750mA

did you notice any problems with the usb socket before this happened? or it might just be a fried battery

fried battery appears to be the best guess at this point
There have been minor problems with the socket in the past but nothing that is of any concern. It registers on my laptop (Moto Desk Man) and buttons are responsive then but will not charge. No help in store either because I'm out of warrenty as well so looks like time for a new phone.

check if the battery is misplaced, that can be the cause (must try out everything)

SuicideFlasher said:
check if the battery is misplaced, that can be the cause (must try out everything)
Click to expand...
Click to collapse
erm, you cannot misplace it, since it's not user-replaceable.
My GF has just had the same story with HTC One X - she was just playing poker app, the phone said the battery is low and then died. Completely died. I brought it to the service center and got it back in 10 days. The staff-girl said they changed 2 main-boards(!), but docket stated they changed the battery and a controller. So I'd say you don't have much choice =(
P.S. She used to use by charger for the good half of all recharges, so i just stopped using her one just in case =)

In a german forum an user had the same issue. So he bought a factory-cable (about 5 Euro), charged the battery with this and he could boot his phone again.
So maybe it's worth for you to try.
via RazR I & Tapatalk 4

[Q] What does this flex cable connect?

Can someone tell me what this flex cable is connecting?
My phone would sometimes spontanously freeze and switch off, showing the 3 red leds and just stops responding. It won't even take a charge. Usually the battery is at 60% when the phone dies, and sometimes it shows a constant RED led.
The back cover is loose (but has enough adhesive to actually stick reasonably, takes little force to open it up), so I pressed that connector with medium force. The next thing that happened, is that the phone responded to the charger, booted to the "charging state", where it shows the battery state and so on (which it shows it's approx on 60%.
Or could it be that I press something else, which causes my phone to work properly again?

emiglet said:
Can someone tell me what this flex cable is connecting?
My phone would sometimes spontanously freeze and switch off, showing the 3 red leds and just stops responding. It won't even take a charge. Usually the battery is at 60% when the phone dies, and sometimes it shows a constant RED led.
The back cover is loose (but has enough adhesive to actually stick reasonably, takes little force to open it up), so I pressed that connector with medium force. The next thing that happened, is that the phone responded to the charger, booted to the "charging state", where it shows the battery state and so on (which it shows it's approx on 60%.
Or could it be that I press something else, which causes my phone to work properly again?
Click to expand...
Click to collapse
Cable with connector in green box is for side keys, gyro and microphone. :good:

neoxx3m said:
Cable with connector in green box is for side keys, gyro and microphone. :good:
Click to expand...
Click to collapse
Thanks/Hvala!
But do you know what could be faulty on this specific point, which causes my phone to not charge? Can I find somewhere a complete guide to the disassembly and identification of all parts? It would make it alot easier for me . My phone is running again, going strong at 65% and still discharging for the last 3 hours. I'm logging the microVolts, temperature and other stats from the battery to see if it's the battery causing the malfunction, which I doubt.
Anyway, there should be something. By the way, prior to the issues, my phone dropped flat on the screen on tiles, about 1 meter high. So most likely, there is something loose/messed up. But I don't know what causes the entire system to flash the LED 3 times, saying that the battery is drained, yet after pressing on this point, immediately start up while on the charger.

emiglet said:
Thanks/Hvala!
But do you know what could be faulty on this specific point, which causes my phone to not charge? Can I find somewhere a complete guide to the disassembly and identification of all parts? It would make it alot easier for me . My phone is running again, going strong at 65% and still discharging for the last 3 hours. I'm logging the microVolts, temperature and other stats from the battery to see if it's the battery causing the malfunction, which I doubt.
Anyway, there should be something. By the way, prior to the issues, my phone dropped flat on the screen on tiles, about 1 meter high. So most likely, there is something loose/messed up. But I don't know what causes the entire system to flash the LED 3 times, saying that the battery is drained, yet after pressing on this point, immediately start up while on the charger.
Click to expand...
Click to collapse
Please PM me. (you speak croatian?)

[Q] [Help Thread] Nook HD not booting at all

I recently went on a 3 month trip. Before I left, my nook was working perfectly fine, when i got back, it didn't work at all. It's not dead because i left it plugged in overnight but it still didn't turn on. when i plug it in the LED goes from orange to green and then off (or green to orange, i can't remember). The screen doesn't turn on at all. I can't get to recovery either.
This is a Nook HD, I believe it had CM11.
:crying:
Can this be fixed
or should i plan it's funeral

Same here
The same has happened to me. Screen doesn't turn on, but there is power, I can play it into my laptop and something is there, just not enough.
Good excuse for a new tablet!

It can be fixed. I've done it before. It has to do with the fstrim not being compatible with certain hardware versions of our device. If I can remember how I fixed it, I'll post it here. Trying to fix mine (again).

tambourineman86 said:
It can be fixed. I've done it before. It has to do with the fstrim not being compatible with certain hardware versions of our device. If I can remember how I fixed it, I'll post it here. Trying to fix mine (again).
Click to expand...
Click to collapse
If would be fab if you could fix. Seems to be a common issue

I was able to fix it. YMMV.
1) Make sure the Nook is completely off and unplugged
2) Take out your sdcard
3) Hold down power button until the "battery depleted" icon shows, then promptly plug in the power before the icon disappears.
4) Let it set. The screen will go black, then it will attempt to boot and get stuck on the faint black screen, but this time, the charging light should stay amber.
If you want to be safe, wait until the device reboots itself. That could take hours though. If you're plugged into the wall wait at least 30 - 45 minutes before holding the power button down til it shuts down and then rebooting it (with the sdcard inserted).
Good luck, I hope it works for you.
EDIT: Also, I've read this may also have to do with wifi sending the device into some sort of strange bootloop when the screen is off. I personally believe it has more to do with the fstrim of JB but perhaps changing the wifi sleep policy may prevent this issue from happening again. I'm skeptical, but figured I'd pass that info along if anyone wants to try it as well.

tambourineman86 said:
I was able to fix it. YMMV.
1) Make sure the Nook is completely off and unplugged
2) Take out your sdcard
3) Hold down power button until the "battery depleted" icon shows, then promptly plug in the power before the icon disappears.
4) Let it set. The screen will go black, then it will attempt to boot and get stuck on the faint black screen, but this time, the charging light should stay amber.
If you want to be safe, wait until the device reboots itself. That could take hours though. If you're plugged into the wall wait at least 30 - 45 minutes before holding the power button down til it shuts down and then rebooting it (with the sdcard inserted).
Good luck, I hope it works for you.
EDIT: Also, I've read this may also have to do with wifi sending the device into some sort of strange bootloop when the screen is off. I personally believe it has more to do with the fstrim of JB but perhaps changing the wifi sleep policy may prevent this issue from happening again. I'm skeptical, but figured I'd pass that info along if anyone wants to try it as well.
Click to expand...
Click to collapse
Not sure we have the same problem. My screen doesn't come on at all, I don't get a battery depleted icon, no matter how long I hold in the power button. The only sign of life I get is when it's plugged in, when it goes from orange to green after about 10 seconds.
Thanks for the help, but I think it's a lost cause.

YMMV. But mine was the same issue. You should be able to get the icon by holding the power button down for 5 or 6 seconds. I'd say just eff with it until that icon appears. Try different button combinations. I used power and home trying to get the icon to show.

developerbuzz said:
when it goes from orange to green after about 10 seconds.
Thanks for the help, but I think it's a lost cause.
Click to expand...
Click to collapse
Anyway... since people are continually running into this kind of issue...
Give or take 21 seconds after turning orange it turns green during actual boot cycle into rom
Give or take 10 seconds after turning orange is cwm internal recovery.
After about 10 seconds the charging screen image disappears.
The charging screen image once finally no longer may not show up again until full power off/on (holding power button > 10 seconds or full battery discharge). Unplugging and plugging back in does nothing except making the device look bricked if there's too much light shining on it.
Device may not automatically leave the above state under a specific situation(s). May still need manual full power off/on.
Guessing 10 seconds could also be something else during the early/late boot process or other. The light changing color though should indicate that something is indeed happening.
Light should stay green during the boot process if its completely and fully no questions asked 100%. If you go based on that than yours doesn't appear to be completely fully charged which should either mean its turning on and using battery or not charging correctly.
The light turning off is curious. The device could be shutting off. If light comes back on a moment later then the device has rebooted. if the light stays off = n/a.
If its booting into recovery then the device would be available via adb. At that point it could be further evaluated.
On the off chance the screen was damaged it should boot and usb should be available via computer as well as adb.
If not then its probably toast unless its simply not getting a good enough current causing mislead battery stats and/or not enough energy to get to charging screen (bad wall power adapter in use, damaged power cable - though could be bad battery, defect, damage or whatever). OR there's some major error on behalf of the user happening (think should have tried that in the morning not while 1/2 asleep or came home from long trip and forget how that works).
Maybe the only other things are the emmc brick bug, was left sitting in the sun or heat or ocean air or other physical damage/defect even to the power port as well.
Or maybe it was mad that you left it. Shouldn't have hurt its feelings you know. At least its not crying battery acid on you.
That should just about cover everything except for the things not mentioned. Since its your device, you decide what happened.
Its complicated so anyone see any improvements, clarifications, or mistakes? Please put it in a post.

Jsorren said:
when i plug it in the LED goes from orange to green and then off (or green to orange, i can't remember). The screen doesn't turn on at all.
Click to expand...
Click to collapse
Bumping this thread to make it aware that there is a real answer. I have been able to duplicate this problem and rather easily too.
The problem is indeed from bad power. The device isn't receiving the correct amount of power needed to charge and start from a fully discharged battery.
To safely* duplicate this you can use a usb extension that isn't fully connected to the nook power cable. You may need to fully connect it first then slowly disconnect/connect till the light turns green when it should actually be charging. It won't actually charge in this state, or if it is, its very little and the battery percentage will continue to drop.
Leave the cable as is and unplugged. After the tablet is fully discharged, connect the usb cable. The light will change through the modes and turn off. The device will not turn on.
There are probably other ways to cause the problem like for instance a portable usb battery that doesn't put out enough juice (not the orange kind). Etc.
* It didn't hurt mine, but not my fault if it breaks your device.

sandsofmyst said:
Bumping this thread to make it aware that there is a real answer. I have been able to duplicate this problem and rather easily too.
The problem is indeed from bad power. The device isn't receiving the correct amount of power needed to charge and start from a fully discharged battery.
To safely* duplicate this you can use a usb extension that isn't fully connected to the nook power cable. You may need to fully connect it first then slowly disconnect/connect till the light turns green when it should actually be charging. It won't actually charge in this state, or if it is, its very little and the battery percentage will continue to drop.
Leave the cable as is and unplugged. After the tablet is fully discharged, connect the usb cable. The light will change through the modes and turn off. The device will not turn on.
There are probably other ways to cause the problem like for instance a portable usb battery that doesn't put out enough juice (not the orange kind). Etc.
* It didn't hurt mine, but not my fault if it breaks your device.
Click to expand...
Click to collapse
I actually ended up fixing it yesterday!! I haven't touched it in about 3 months, and I was planning on just throwing it out getting rid of it some how. For the heck of it, I decided to plug it in, assuming that it was gonna go through the same process. But this time it went from green to amber, but it never went off. So I pressed the power button and the battery icon appeared. This was a really good sign. So I left plugged in for about 5 to 10 minutes then tried to power on.:fingers-crossed: As soon as I saw that '' Nook" boot up screen, my heart stopped. It booted up perfectly and I almost blew up from excitement :victory:. So I then flashed the stock firmware back onto it, so this would never happen again.
I guess the battery had to be completely depleted or just had to cool down. Idk but either way this was one heck of a miracle
So I recommend for anyone having this problem to just leave it off and don't mess with it. I wouldn't say for 3 months like I did but maybe test it each week or wait a month if you have good patience

Wow. Man, that's awesome! Glad you posted that update on it. Thought if you had posted an update it would be the opposite as in trashed it
Actually, I guess only you could answer if you had also moved/unplugged the power cable from the wall adapter or put it into a different wall adapter, etc. Thinking there could have been a difference there.
These modern day devices are so finicky, guess anything is possible. Like you say, maybe sitting without power is another answer.

From some experimentation I have etermined that your power adapter (that plugs into the outlet) is the issue. It does not like to be leaft plugged in indefinately. It will continually use power even when the nook is not plugged in.
Also, if you use a differnt adapter you will have the same problem unless it is also of the exact same voltage and amps.