n7000 won't turn on no recovery only download mode - Galaxy Note GT-N7000 Q&A, Help & Troubleshooting

my phone after i downloaded stock rom (don't have another information about it it wasn't me) didn't open, only black screen when i press power button nothing happens but when i connect usb cable firstly it was getting like it was charging now it just keep appearing and disappearing but when i press (power button +vol. down +menu button) i gets me to download mode i tried many times to get to recovery but i can't please help me it's been 2 days and i can't find a solution .

roryror2010 said:
my phone after i downloaded stock rom (don't have another information about it it wasn't me) didn't open, only black screen when i press power button nothing happens but when i connect usb cable firstly it was getting like it was charging now it just keep appearing and disappearing but when i press (power button +vol. down +menu button) i gets me to download mode i tried many times to get to recovery but i can't please help me it's been 2 days and i can't find a solution .
Click to expand...
Click to collapse
Download Odin and Stock rom for your phone, open odin click on PDA and navigate to your stock rom you downloaded, check Auto Reboot and F.Reset Time checkboxes in odin put your phone i download mode Connect USB data cable to Phone. The ID:COM box will will be highlighted and turn to color yellow when the phone is properly connected and already detected with Odin. Tick the 'START' button when all is set and ready to begin flashing. Don't touch phone while odin is flashing wait until you get green box with PASS sign and until your phone reboots, and do full reset. Hope it helps.

RoloRS said:
Download Odin and Stock rom for your phone, open odin click on PDA and navigate to your stock rom you downloaded, check Auto Reboot and F.Reset Time checkboxes in odin put your phone i download mode Connect USB data cable to Phone. The ID:COM box will will be highlighted and turn to color yellow when the phone is properly connected and already detected with Odin. Tick the 'START' button when all is set and ready to begin flashing. Don't touch phone while odin is flashing wait until you get green box with PASS sign and until your phone reboots, and do full reset. Hope it helps.
Click to expand...
Click to collapse
i tried to flash stock rom but still same problem.

roryror2010 said:
my phone after i downloaded stock rom (don't have another information about it it wasn't me) didn't open, only black screen when i press power button nothing happens but when i connect usb cable firstly it was getting like it was charging now it just keep appearing and disappearing but when i press (power button +vol. down +menu button) i gets me to download mode i tried many times to get to recovery but i can't please help me it's been 2 days and i can't find a solution .
Click to expand...
Click to collapse
If your phone is still detectable in odin follow the instructions for odin in this link:
http://forum.xda-developers.com/showthread.php?t=1901191
boot into download mode
start odin3 and configure it as in picture below
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
connect phone in download mode to PC via USB
press start to flash the tar.md5 package
Location of tar.md5 recoverys: https://goo.im/devs/philz_touch/CWM_Advanced_Edition/n7000/
Then once youve got a working recovery just pick ur rom and flash from extrnal sd card
Good luck m8

pdolton2000 said:
If your phone is still detectable in odin follow the instructions for odin in this link:
http://forum.xda-developers.com/showthread.php?t=1901191
boot into download mode
start odin3 and configure it as in picture below
connect phone in download mode to PC via USB
press start to flash the tar.md5 package
Location of tar.md5 recoverys: https://goo.im/devs/philz_touch/CWM_Advanced_Edition/n7000/
Then once youve got a working recovery just pick ur rom and flash from extrnal sd card
Good luck m8
Click to expand...
Click to collapse
thanks for your reply but still same problem .

roryror2010 said:
thanks for your reply but still same problem .
Click to expand...
Click to collapse
Thats fine pal...so what did odin say...was it detectable...did it appear to flash ok but just doesnt let you boot into recovery on the phone or was there an error with odin?
The more info the more we can help

pdolton2000 said:
Thats fine pal...so what did odin say...was it detectable...did it appear to flash ok but just doesnt let you boot into recovery on the phone or was there an error with odin?
The more info the more we can help
Click to expand...
Click to collapse
ok the device was detectable flash was pass there was no errors but when i press [vol. up + power +menu] nothing happens.

roryror2010 said:
ok the device was detectable flash was pass there was no errors but when i press [vol. up + power +menu] nothing happens.
Click to expand...
Click to collapse
Maybe your plus key is not working?
If odin detected it, and odin said pass thats impossible unless it really was successful...that recovery is on there alright...its just that plus button must be to blaim...question is how can you test the plus button really works?
EDIT
Hang on did odin say pass when flashing your stock rom before Using rolors's suggestion?
---------- Post added at 09:44 PM ---------- Previous post was at 09:23 PM ----------
roryror2010 said:
ok the device was detectable flash was pass there was no errors but when i press [vol. up + power +menu] nothing happens.
Click to expand...
Click to collapse
Ok this is the only other thing you can try. There is a way of using adb commands to kick your device into recovery mode...and adb commands to install roms...first you need this neat piece of software For windows so you can use adb commands to your phone
http://forums.androidcentral.com/so...g/415287-open-source-adb-console-wizzrah.html
Then type "adb reboot recovery" i think whilst in dwnload moad to see if at least it tries to....if you see dwnload mode dissapear you know it recieved the command at least...best i can do...a quick google of adb commands will show you more Though
Good luck.

pdolton2000 said:
Maybe your plus key is not working?
If odin detected it, and odin said pass thats impossible unless it really was successful...that recovery is on there alright...its just that plus button must be to blaim...question is how can you test the plus button really works?
EDIT
Hang on did odin say pass when flashing your stock rom before Using rolors's suggestion?
---------- Post added at 09:44 PM ---------- Previous post was at 09:23 PM ----------
Ok this is the only other thing you can try. There is a way of using adb commands to kick your device into recovery mode...and adb commands to install roms...first you need this neat piece of software For windows so you can use adb commands to your phone
Then type "adb reboot recovery" i think whilst in dwnload moad to see if at least it tries to....if you see dwnload mode dissapear you know it recieved the command at least...best i can do...a quick google of adb commands will show you more Though
Good luck.
Click to expand...
Click to collapse
thanks for your reply i tried adb console while i'm on download mode first i entered "adb reboot recovery " i got "Error: error: device not found" then i entered "adb devices" and there was nothing in "list of devices"

roryror2010 said:
thanks for your reply i tried adb console while i'm on download mode first i entered "adb reboot recovery " i got "Error: error: device not found" then i entered "adb devices" and there was nothing in "list of devices"
Click to expand...
Click to collapse
Out of curiosity is there any unknown devices in device manager when its in dwnload mode? Or anything with a yellow exclamation mark...its strange because odin only detects devices with adb drivers installed so this adb software should pick it up really....if everything seems fine in device manager try right clicking on this program and pressing run as administrator....ive never used this program though so ill experiment tomoz myself with it and report back....we will not be beaten lol

roryror2010 said:
thanks for your reply i tried adb console while i'm on download mode first i entered "adb reboot recovery " i got "Error: error: device not found" then i entered "adb devices" and there was nothing in "list of devices"
Click to expand...
Click to collapse
You haven't configured adb correctly for your computer. If it was done properly, you would have got your device listed.
Please follow proper instructions before attempting anything worthy to your device.

i did it now i can reach recovery mode and i tried to wipe cache n data but ;i'm facing the same problem i only got to recovery mode while usb cable is connected it gets me battery logo but it doesn't charge it keeps gets on n off i pressed (vol. up +menu +power) i was able to get to recovery mode ,any suggestions

nobody can help me or what ??

Problem Solved
finally i solved my problem i just bought a new battery and it worked like a charm ,
thank you guys for trying.

Related

[Q] No bootloader, only connect to PC Icon - please help

Hi,
I have got a problem with my HD7 device.
After unsuccesful flashing it went to the state:
1) After it starts it goes straight into the "Connect to PC" mode
Photo:
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
2)
It is unable to go into booloader mode (Power + vol down) because it ignores it - it goes straight to 1)
3) If I connect it to zune it detects it but momentally it returns error
I don't have an idea what to do next, I have working Y-cable and sd-card with 1gb card which I already used few months ago.
adminmodeenabled said:
Hi,
I have got a problem with my HD7 device.
After unsuccesful flashing it went to the state:
1) After it starts it goes straight into the "Connect to PC" mode
Photo:
2)
It is unable to go into booloader mode (Power + vol down) because it ignores it - it goes straight to 1)
3) If I connect it to zune it detects it but momentally it returns error
I don't have an idea what to do next, I have working Y-cable and sd-card with 1gb card which I already used few months ago.
Click to expand...
Click to collapse
did u try entering the USB host mode? If you can enter the USB host mode try flashing again using the gold card method....
And when u said unsuccessful flashing were u updating through Zune?
sirajgoku said:
did u try entering the USB host mode? If you can enter the USB host mode try flashing again using the gold card method....
And when u said unsuccessful flashing were u updating through Zune?
Click to expand...
Click to collapse
No - it is not because updating through Zune, I tried to upload new Rom - previously I had WP7.5 with 2 month old rom
I tried to reflash using 2 roms with gold card method, both times it completed "UPDATE SUCCESS" but it doesnt' boot up - still the same screen.
Update process looked like that
1) First rom
RADIO - OK
BOOTLOADER - OK
OS - OK
RCUST - OK
TOUCH - OK
TOUCH - OK
TOUCH - OK
TOUCH - OK
TOUCH - OK
2) Second rom
RADIO - OK
BOOTLOADER - OK
OS - OK
RCUST - OK
3) ZUNE ERROR: C101002E - RESTORE ERROR
4) RUU_Schubert_HTC_Europe_1.69.401.01_Radio_5.54.09.21_22.33b.50.10_Signed_SCHUBERT_RELEASE.exe
ERROR[260] CONNECTION - THe Update Utility can't connect your phone
Additional info - I have got SPL 1.54
Advanced setting problem
Hi Dear members,
I used advanced setting, after some setting some of my phone (htc-hd7) do not work such as Nokia drive, Nokia map, touchxplorer. When I touch them to use, the icon only tremble. This icon are tottering and don't work.
I tried to reinstall again but the ds market also does not work. I upgrade ds market and install devstor but this app also does not work.
Please help me what can I do ?
My direct email is [email protected]
m_r_anari said:
Hi Dear members,
I used advanced setting, after some setting some of my phone (htc-hd7) do not work such as Nokia drive, Nokia map, touchxplorer. When I touch them to use, the icon only tremble. This icon are tottering and don't work.
I tried to reinstall again but the ds market also does not work. I upgrade ds market and install devstor but this app also does not work.
Please help me what can I do ?
My direct email is [email protected]
Click to expand...
Click to collapse
Please open a separate thread for your question as it has no relevancy to the OP.
Did u try reflashing using the Y cable?
sirajgoku said:
Did u try reflashing using the Y cable?
Click to expand...
Click to collapse
Yes, I did it 3 times. Here are logs from screen
1) First rom
RADIO - OK
BOOTLOADER - OK
OS - OK
RCUST - OK
TOUCH - OK
TOUCH - OK
TOUCH - OK
TOUCH - OK
TOUCH - OK
2) Second rom
RADIO - OK
BOOTLOADER - OK
OS - OK
RCUST - OK
3) Rom extracted from %TEMP% by running RUU_Schubert_HTC_Europe_1.69.401.01_Radio_5.54.09. 21_22.33b.50.10_Signed_SCHUBERT_RELEASE.exe
RADIO - OK
BOOTLOADER - OK
OS - OK
RCUST - OK
did you try using another CardReader or FlashDrive?
KatoGuro said:
did you try using another CardReader or FlashDrive?
Click to expand...
Click to collapse
Cardreader - it detects it, detects rom on it, and loads everything from it with
"OK, OK, OK"
and then it writes that update is successful
sirajgoku said:
did u try entering the USB host mode? If you can enter the USB host mode try flashing again using the gold card method....
Click to expand...
Click to collapse
Press power for about 10 sec, then try to get in USB host mode for reflash
KatoGuro said:
Press power for about 10 sec, then try to get in USB host mode for reflash
Click to expand...
Click to collapse
But what for? Because if I press power it immediately starts to show HTC logo.
Maybe I should do it in different situation?
when you get stuck into the "Connect to PC" mode, press PowerButton for 10 sec for Restart, then hold Power+Camera+VolumeDown until the USB Host Mode appears!
KatoGuro said:
when you get stuck into the "Connect to PC" mode, press PowerButton for 10 sec for Restart, then hold Power+Camera+VolumeDown until the USB Host Mode appears!
Click to expand...
Click to collapse
I know how to enter USB HOST MODE - I reflashed the rom few times using goldcard (logs are in previous posts).
No I am trying your way - not after taking of battery, but after exiting from "Connect to PC" using power button.
SHUIMG.nhb -OK
RADIO - OK
BOOTLOADER - OK
OS - RCUST - OK
TOUCH - OK
TOUCH - OK
TOUCH - OK
TOUCH - OK
TOUCH - OK
Update Complete
UPDATE SUCCESS
Same - booting to "Connect to PC Mode"
but how...
how you managed to flash in just seconds??? should take about 30 min
KatoGuro said:
but how...
how you managed to flash in just seconds??? should take about 30 min
Click to expand...
Click to collapse
I thought about what you wrote and that was the only logical explanation - so after your answer I already guessed what did you mean.
Generally yeah...it took something about 15 minutes (not sure if it was 30).
But there is one problem - When i push the power button during the "Connect to pc screen" it reboot itselfs after 3-4 seconds and then is starting again so I have to press Camera + vol down button to enter USB Host mode (I am still holding the power button).
Maybe you meant something else?
I have time - I can try multiple things
adminmodeenabled said:
I thought about what you wrote and that was the only logical explanation - so after your answer I already guessed what did you mean.
Generally yeah...it took something about 15 minutes (not sure if it was 30).
But there is one problem - When i push the power button during the "Connect to pc screen" it reboot itselfs after 3-4 seconds and then is starting again so I have to press Camera + vol down button to enter USB Host mode (I am still holding the power button).
Maybe you meant something else?
I have time - I can try multiple things
Click to expand...
Click to collapse
I can even record what I do and upload video

[Q] GT-P1000 bricked after wrong bootloader patch

Hi !
I have a european GSM Galaxy Tab (GT-P1000) with Gingerbread and it seems that I just bricked it... Let me explain :
- I have a Mac, so I rooted it using adb and the Terminal, following the DooMLoRD's method. This worked fine.
- I applied the bootloader patch found here : http://forum.xda-developers.com/showthread.php?t=888071
(to make it short : the (french) tutorial I followed did not say that it wasn't suppose to work on Gingerbread, so I did it...and it failed).
- But at the moment the Tab was still working ! It was showing a "rainbow" screen before boot and was recognized by my computer as" 7 CDCs" which was totally useless. Here is the rainbow screen :
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
But it was able to boot. I found someone with the same problem in the bootloader patch thread and people answered him to flash it with Odin. So I installed VirtualBox and succeded to use Odin (1.7).
- The Galaxy Tab in Download Mode wasn't recognized by Odin at all, although I installed Samsung's drivers. Heimdall was able to install the drivers for the Tab but the .pit file download failed. So I did nothing wrong with Odin or Heimdall since I did nothing at all.
- And yesterday, the Tab was plugged in the computer, in Download Mode, and it switched off definitely. When I plug it in using the USB charger, this image blink slowly :
It can't boot in any mode. I tried pushing the power button for 30+ seconds, tried Power + Volume Up, Power + Volume Down, it doesn't work. I let it plugged in the whole night to see if it's not a "coma brick" (like said on the "unbrick the GTab thread", it keeps blinking. Trying to boot while plugged in doesn't work and it's not recognized by the computer. I haven't found any answer to this precise problem on the forum so I finally decided to ask.
Here are my questions :
- what is happening (so that it doesn't happen again) ?
- can I fix it and how ?
Thank you in advance
PS : my english may not be perfect, sorry. I'm french and I do my best
Your picture show the tab in another download mode.
You can still flash it with heimdall
Follow my signature to new overcome link.
You only need the gb stock save v5
You can unpack the Rom and find all the necessary files.
Sent from my GT-I9300 using xda app-developers app
Heimdall can't see my device
priyana said:
Your picture show the tab in another download mode.
You can still flash it with heimdall
Click to expand...
Click to collapse
Thank you for your answer ! Sadly my Tab isn't recognized by the computer (Heimdall can't detect any device in download mode). The image only show when it's plugged in the wall.
EDIT : there is something new ! Now the Tab stopped blinking and show the image I posted before when I plug it in the wall. I can unplug it, the image stay, so I guess it lauches a kind of download mode... However Heimdall on Mac still can't find it. I need to try with a PC.
EDIT 2 : it blinks again. Wut.
Rigatoni said:
Thank you for your answer ! Sadly my Tab isn't recognized by the computer (Heimdall can't detect any device in download mode). The image only show when it's plugged in the wall.
EDIT : there is something new ! Now the Tab stopped blinking and show the image I posted before when I plug it in the wall. I can unplug it, the image stay, so I guess it lauches a kind of download mode... However Heimdall on Mac still can't find it. I need to try with a PC.
EDIT 2 : it blinks again. Wut.
Click to expand...
Click to collapse
Hey. I got the same problem as you thanks to some user here named "cx5" and his stupid misleading instructions that got my tab bricked.
Anyway, i finally found a awesome application that managed to unbrick my tab. Yeah it's ALIVE!! back again Not sure if this will work on your tab but IF you are interested and decided to take a risk then go http://forum.xda-developers.com/showthread.php?t=1153310 and download OneClickUnbrick then connect your Tab to your PC using USB. and leave it there and wait for 20 Minutes it will turn on during that time and quickly click unbrick button on the application then select List All Devices then click the Samsung USB port that you connected your tab at, Wait awhile for installing Driver, after installing completed click unbrick button again. let me know if this works for you too.
Thank you !
dc2mx said:
Hey. I got the same problem as you thanks to some user here named "cx5" and his stupid misleading instructions that got my tab bricked.
Anyway, i finally found a awesome application that managed to unbrick my tab. Yeah it's ALIVE!! back again Not sure if this will work on your tab but IF you are interested and decided to take a risk then go http://forum.xda-developers.com/showthread.php?t=1153310 and download OneClickUnbrick then connect your Tab to your PC using USB. and leave it there and wait for 20 Minutes it will turn on during that time and quickly click unbrick button on the application then select List All Devices then click the Samsung USB port that you connected your tab at, Wait awhile for installing Driver, after installing completed click unbrick button again. let me know if this works for you too.
Click to expand...
Click to collapse
That worked but my bootloader is still a mess because I see some funky rainbow lines when booting and can't access to recovery... How did you fix that ?
Rigatoni said:
That worked but my bootloader is still a mess because I see some funky rainbow lines when booting and can't access to recovery... How did you fix that ?
Click to expand...
Click to collapse
Hmm.. Actually, i meant i am stuck in Phone ! Computer screen and can't do anything about it which is same as you. i am not sure how do fix this rainbow screen you're getting. i guess wait for priyana reply. since he is experienced with galaxy tabs. the method above is to fix soft bricked.
You are right that rainbow screen is caused by boot loader patch.
Just use the gbstock safe from overcome. It has GB bootloader.
Follow my signature for the link.
There is the guide in pdf but for Odin.
If you can get it to work with Odin, jump to page 7 of the guide,
And flash according to the picture.
In completion it will reboot.
I did write about using heimdall command line somewhere.
Just search the forum.
Sent from my GT-P1000 using xda app-developers app
Thank you again !
So :
- the Tab is booting again but show strange lines when it boots
- the computer don't see it : Odin don't work, Heimdall seems to fail when trying to flash a zImage, and heimdall-frontend fail at downloading .pit file
Any help ?
I don't know if virtual box work.
In my experience it never works for me.
Try get a fresh PC.
Btw, you can try boot to safe mode (windows) and remove the USB driver for the tab.
And reinstall the driver from GB stock safe.
BTW also, pit file doesn't matter, I think. Boot loader is boot.bin and Sbl.bin
They both can be flashed via heimdall without pit file, you care to try?
But this is the most dangerous operation. Of all flashing, flashing bootloader is one that will kill a tab, as you have found yourself by patching a GB boot loader.
I guess if nothing works, you try heimdall command file with the boot loader part.
Sent from my GT-P1000 using xda app-developers app
priyana said:
I don't know if virtual box work.
In my experience it never works for me.
Try get a fresh PC.
Btw, you can try boot to safe mode (windows) and remove the USB driver for the tab.
And reinstall the driver from GB stock safe.
BTW also, pit file doesn't matter, I think. Boot loader is boot.bin and Sbl.bin
They both can be flashed via heimdall without pit file, you care to try?
But this is the most dangerous operation. Of all flashing, flashing bootloader is one that will kill a tab, as you have found yourself by patching a GB boot loader.
I guess if nothing works, you try heimdall command file with the boot loader part.
Sent from my GT-P1000 using xda app-developers app
Click to expand...
Click to collapse
Ok, I'll try with Heimdall command line. Thank you ! I'll give some news later, if that worked or not.
EDIT : So, first I tried to flash the GB Stock rom with command line. It worked fine, but it didn't fix my problem. Since there was nothing else to do, I flashed the booloader files of the GB stock rom (with heimdall command line, again) and I don't know what I have done wrong, but it failed and the Tab looks dead. Doesn't boot, even after a night plugged in the wall. I guess there's nothing I can do, now ?
Sorry to hear that.
I don't know why it got to this stage.
Can you do the oneclickunbrick again?
Plug to PC for at least 20min and see if it comes alive like before?
Sent from my GT-P1000 using xda app-developers app
priyana said:
Sorry to hear that.
I don't know why it got to this stage.
Can you do the oneclickunbrick again?
Plug to PC for at least 20min and see if it comes alive like before?
Sent from my GT-P1000 using xda app-developers app
Click to expand...
Click to collapse
No it doesn't work. I think I did something wrong and only flashed the primary bootloader... I tried plugging it to the PC but it doesn't work anymore. I think it's over maybe some people I know will be able to help me doing hard stuff to fix it, I hope.
just out of curiosity,
what command was it that you issued to flash the bootloaders?
Same problem I have now the blinking while charging in the main supply. After trying some restocking on my GT-p1000 and always fail using Odin and other guides, now I can't open my tab but when I plug it in the main charger it shows warning link between phone and computer. Then afterwards, after I left it charging for 30mins. My tab now just blinking while the charger is on. Its just keep on blinking with warning link phone and computer showing.
Any same problems? What should I do. I waited and charged it for almost 4 hours, still its blinking.
Try OneClickUnbrick
I tried now OneClick and then after that my tab stuck in the samsung logo and can't turn off via button. Computer can recognize the tablet but it is not in the download mode.
~Now I turned it off. Charging it to full. Hopefully after charging it Odin will now work. Cause it always fail in movinand flash. I followed all the instruction using overcome and safe flash.
now I can access download mode but odin can't recognize the tab.
I am out of idea.
The most recent case I read of this, was fixed by removing and reinstalling the USB driver for the samsung device.
I personally use linux. And heimdall seems to always able to reach my tab.
I suspect the OneClickUnbrick's heimdall driver (zadig) is obscuring your tab from Odin.
Reinstall the USB driver again

[Q] Xperia Z cannot get in FLASH MODE

I try to update my Xperia Z but while need press volume up button and plug in cable, nothing happen~~~
keroro84 said:
I try to update my Xperia Z but while need press volume up button and plug in cable, nothing happen~~~
Click to expand...
Click to collapse
I think you have to press the volume down button and then plug it in.
hope i helped.
Mufrad said:
I think you have to press the volume down button and then plug it in.
hope i helped.
Click to expand...
Click to collapse
Same, I try Press Volume Up or Volume Down, also same, nothing happen.:crying:
keroro84 said:
Same, I try Press Volume Up or Volume Down, also same, nothing happen.:crying:
Click to expand...
Click to collapse
I only get an unknown USB device and i don't seem to have any correct driver.
unable to access flashmode
nurps said:
I only get an unknown USB device and i don't seem to have any correct driver.
Click to expand...
Click to collapse
i can confirm that, got the same issue - i installed at least cwm for cm10.1, want to go back to stock rom - need another kernel - only can be installed by fastboot but i can not access the mode - volume up or down while plugging in usb cable doesn't work, no driver change
keroro84 said:
I try to update my Xperia Z but while need press volume up button and plug in cable, nothing happen~~~
Click to expand...
Click to collapse
same here, trying to to update using Sony PC Companion and was told in the instructions, under step 5, to press and hold volume don key on the phone while plugging the USB cable into your phone, tried several times, even restarted phone, not happening.. HELP!1111111111
- Make sure the phone has charge.
- Remove SD card from phone.
- Make sure the correct divers are installed:
http://forum.xda-developers.com/showthread.php?t=2153261
Scroll down to: [ before we begin unlocking bootloader ]
Here 3 packages are given for fastboot drivers:
download the fastboot package with usb drivers (alternate drivers if the ones in package dont work OR this)
- Try another PC \ USB port \ USB calbe?
- Switch the phone OFF , hold the volume UP button while you plug-in the USB. (DO NOT PRESS POWER!) Blue led?
- Switch the phone OFF , hold the volume DOWN button while you plug-in the USB. (DO NOT PRESS POWER!) Green led?
Does any of these options work?
Kind regards, Stefan.
No change for me, works fine on another PC. But i want to be able to update that phone in my own home.
Thaevil0ne said:
- Make sure the phone has charge.
- Remove SD card from phone.
- Make sure the correct divers are installed:
http://forum.xda-developers.com/showthread.php?t=2153261
Scroll down to: [ before we begin unlocking bootloader ]
Here 3 packages are given for fastboot drivers:
download the fastboot package with usb drivers (alternate drivers if the ones in package dont work OR this)
- Try another PC \ USB port \ USB calbe?
- Switch the phone OFF , hold the volume UP button while you plug-in the USB. (DO NOT PRESS POWER!) Blue led?
- Switch the phone OFF , hold the volume DOWN button while you plug-in the USB. (DO NOT PRESS POWER!) Green led?
Does any of these options work?
Kind regards, Stefan.
Click to expand...
Click to collapse
hi, no one of both options works, also tried hard power off (3 x vibrations and then plugin while holding down/up)
anybody, i have sam problem too...Cant see that flashboot drivers are installed in flastoll?
---------- Post added at 09:58 PM ---------- Previous post was at 09:55 PM ----------
anybody? i have same problem too...
Sauriann said:
anybody, i have sam problem too...Cant see that flashboot drivers are installed in flastoll?
---------- Post added at 09:58 PM ---------- Previous post was at 09:55 PM ----------
anybody? i have same problem too...
Click to expand...
Click to collapse
Keep trying, not a lot else you can do.
Sent from my C6603 using xda premium
XperienceD said:
Keep trying, not a lot else you can do.
Sent from my C6603 using xda premium
Click to expand...
Click to collapse
I got the same issue, cant get to fastboot mode, This issue maybe related to the registry, but i dont know how to deal with it.
Sent from my Nexus 4 using xda app-developers app
chungjimmybb said:
This issue maybe related to the registry, but i dont know how to deal with it.
Click to expand...
Click to collapse
Not sure why, it's usually more to do with user error, so simply retrace your steps and start over.
I tried via Sony PC Companion 2.1 and I get this message:
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
I use these rom on Xperia Z:
Sauriann said:
I tried via Sony PC Companion 2.1 and I get this message:
Click to expand...
Click to collapse
So use the flashtool then, and read the stickys too.
I tried flashtool at least 20 times. Simply can not start the installation system (vol. down button + USB cable at the same time does not work!). SO, I can not put phone in flashmode enymore. Flashtool see phone in this mode for a few seconds and then stuck. On the phone i have green led for a sec, then nothing...
So any method that requires phone in flashmode is unusable.
Before this i use it (flashtool) several time normaly.
Sauriann said:
So any method that requires phone in flashmode is unusable.
Click to expand...
Click to collapse
Then you need to clean your computer of all things Sony, remove drivers etc and start over. http://developer.sonymobile.com/services/flash-tool/
XperienceD said:
Not sure why, it's usually more to do with user error, so simply retrace your steps and start over.
Click to expand...
Click to collapse
i got the same issue too and just tried in friend's computer with no luck. i am sure to stick with the flashtool guide step by step, but can't do fastboot mode yet.
Ok this (http://developer.sonymobile.com/services/flash-tool/) work, and this "flashtool" is Emma fom Sony Mobile.
Tnx for help.
keroro84 said:
I try to update my Xperia Z but while need press volume up button and plug in cable, nothing happen~~~
Click to expand...
Click to collapse
Wat kind of version do you use? The regular one or beta one?
Sent from my C6603 using xda app-developers app

[q] my galaxy pocket wont start nor can i enter recovery

HEY GUYS !!
I am new to xda so im not sure if i have posted it at the right place.
anyway, my phone (galaxy pocket GTS5300) is rooted runs on infuzion 2 kernel and has hydroperia v2 custom rom(i followed the instructions from xda)
so recently i wanted to increase its ram so i partioned my external sd and installed swapper 2 (just like the post in xda),everything went all right
then i downloaded "file2sd"" from play store and installed it to gets some space in my phones internal memory but as i opened the app and selected
the format as ext3 the said i have to reboot and i pressed the "" restart now ""button,thats it and the phone just got stuck i waited for some time no buttons responded so removed the battery and tried turning it on but it just shows a blank screen after showing the model no. and i CANT enter recovery mode but i can enter odin (but my laptop does not recognize the device,eventhough i have tried installing all the usb drivers and kies ,i dont know if its because of the data cable or windows8 or my phone ) so i removed my external sd copied all my files and saw (in mini tool partition wizard)that my 2nd partition was full(512 mb)i didnt know what to do and i formatted everything(sd).
i dont know what to do next .someone please help!!!
glenzac said:
HEY GUYS !!
I am new to xda so im not sure if i have posted it at the right place.
anyway, my phone (galaxy pocket GTS5300) is rooted runs on infuzion 2 kernel and has hydroperia v2 custom rom(i followed the instructions from xda)
so recently i wanted to increase its ram so i partioned my external sd and installed swapper 2 (just like the post in xda),everything went all right
then i downloaded "file2sd"" from play store and installed it to gets some space in my phones internal memory but as i opened the app and selected
the format as ext3 the said i have to reboot and i pressed the "" restart now ""button,thats it and the phone just got stuck i waited for some time no buttons responded so removed the battery and tried turning it on but it just shows a blank screen after showing the model no. and i CANT enter recovery mode but i can enter odin (but my laptop does not recognize the device,eventhough i have tried installing all the usb drivers and kies ,i dont know if its because of the data cable or windows8 or my phone ) so i removed my external sd copied all my files and saw (in mini tool partition wizard)that my 2nd partition was full(512 mb)i didnt know what to do and i formatted everything(sd).
i dont know what to do next .someone please help!!!
Click to expand...
Click to collapse
So you can actually enter the "download" mode. Thats good at least.
Win 8 comatible driver --> Samsung 1.5.27.0
Which version of odin do you use? This will wotk for you --> Odin 3.07
thanks 4 quick reply
THANKS FOR THE REPLY!!!!!
I HAVE THE USB DRIVER 1.5.23 and still the phone wont work.
actually i have both odin1.85 and 3.09
glenzac said:
THANKS FOR THE REPLY!!!!!
I HAVE THE USB DRIVER 1.5.23 and still the phone wont work.
actually i have both odin1.85 and 3.09
Click to expand...
Click to collapse
Check under device manager if it shows usb device with yellow triangle while phone is connected to computer (Be sure to set show all devices)
yes
LS.xD said:
Check under device manager if it shows usb device with yellow triangle while phone is connected to computer (Be sure to set show all devices)
Click to expand...
Click to collapse
when i used to connect the phone it would show "usb device not recognized".i tried reinstalling the usb drivers but no use.
glenzac said:
when i used to connect the phone it would show "usb device not recognized".i tried reinstalling the usb drivers but no use.
Click to expand...
Click to collapse
you have to force the installation. Right mouse on device. Install driver. select driver manually. (you have to xtract the driver files from the installer first) show "incompatible" devices --> musg be sth like "USB composite device"
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
k
LS.xD said:
you have to force the installation. Right mouse on device. Install driver. select driver manually. (you have to xtract the driver files from the installer first) show "incompatible" devices --> musg be sth like "USB composite device"
Click to expand...
Click to collapse
im sorry i havent understood what you said, can you PLEASE explain it in a detailed manner
glenzac said:
im sorry i havent understood what you said, can you PLEASE explain it in a detailed manner
Click to expand...
Click to collapse
device manager shoes "unknown device" with a yellow triangle?
glenzac said:
HEY GUYS !!
I am new to xda so im not sure if i have posted it at the right place.
anyway, my phone (galaxy pocket GTS5300) is rooted runs on infuzion 2 kernel and has hydroperia v2 custom rom(i followed the instructions from xda)
so recently i wanted to increase its ram so i partioned my external sd and installed swapper 2 (just like the post in xda),everything went all right
then i downloaded "file2sd"" from play store and installed it to gets some space in my phones internal memory but as i opened the app and selected
the format as ext3 the said i have to reboot and i pressed the "" restart now ""button,thats it and the phone just got stuck i waited for some time no buttons responded so removed the battery and tried turning it on but it just shows a blank screen after showing the model no. and i CANT enter recovery mode but i can enter odin (but my laptop does not recognize the device,eventhough i have tried installing all the usb drivers and kies ,i dont know if its because of the data cable or windows8 or my phone ) so i removed my external sd copied all my files and saw (in mini tool partition wizard)that my 2nd partition was full(512 mb)i didnt know what to do and i formatted everything(sd).
i dont know what to do next .someone please help!!!
Click to expand...
Click to collapse
The Best Solution Is :
Press thanks if It helps
Download CWM From here : http://forum.xda-developers.com/attachment.php?attachmentid=1461120&d=1352197095
Download Stockrom from here : http://www.4shared.com/zip/SZzB-egN/S5300XXLF5_S5300BTULF1_BTU.html
Put both zips in your sd card
go to recovery mode by pressing vol up + home button + power button (Hold for 10 seconds)
Now in recovery mode select apply update from sd card and select cwm file...
Now in cwm mode again go to apply update from sd card ...
Select Stock ROm ZIP...
You will now boot normally
N'ayam Amarsh'e said:
Download The Samsung Unbicking Software from Here http://forum.xda-developers.com/showthread.php?t=1153310 and try it out and if it works press thanks button and also of the creator of this software....
Click to expand...
Click to collapse
Have you tried this before? I did --> no success at all, its made for Galaxy S. Sure try it out
PM me if ya want something-...
further?
LS.xD said:
device manager shoes "unknown device" with a yellow triangle?
Click to expand...
Click to collapse
ok i am working on it
if at all it works what am i to do next?
what all files should i have?
LS.xD said:
Have you tried this before? I did --> no success at all, its made for Galaxy S. Sure try it out
PM me if ya want something-...
Click to expand...
Click to collapse
It's edited now....
glenzac said:
ok i am working on it
if at all it works what am i to do next?
what all files should i have?
Click to expand...
Click to collapse
you have extracted samsung drivers in a folder on your desktop????
right mouse button on unknown device - install driver - searh pc for drivers -> show list -> select folder where the samsung driver is stored -> unmark "compatible devices" and then you can manually select a device if it shoes not compatible -> ignore just install
before we fill 20 more pages may be you can install "gtalk"?
what next???
N'ayam Amarsh'e said:
It's edited now....
Click to expand...
Click to collapse
the soft brick software will not do as i can access odin
so can someone please help me to go ahead with odin
what files would i require?
also there is another major problem my phone wont charge.the second i connect the charger the phone tries to turn on and returns back to the black screen,
please help
glenzac said:
the soft brick software will not do as i can access odin
so can someone please help me to go ahead with odin
what files would i require?
also there is another major problem my phone wont charge.the second i connect the charger the phone tries to turn on and returns back to the black screen,
please help
Click to expand...
Click to collapse
MAN did you installed driver as i said? when its showing Samsung USB comosite device --> flash stock rom with odin. S5300 Stock firmwares make sure to have your region
Your phone has to b connected in "download" mode (by pressing the 3 button combo)
If you cant enter download mode? release battery and connect phone to pc with usb cable then press Vol- and home and power and put back in battery while. Your computer should get the device.
you flash stockrom using odin.
Sry for that complicated chat, but its not that easy using a browser based chat for that. Also you got more then 1 person tell what to do. Seems not workin that good...
So if something is still not cleat, may be install GTalk for easier chat or teamviewer that i can "show" what i mean.
regards
no luck
LS.xD said:
MAN did you installed driver as i said? when its showing Samsung USB comosite device --> flash stock rom with odin. S5300 Stock firmwares make sure to have your region
Your phone has to b connected in "download" mode (by pressing the 3 button combo)
If you cant enter download mode? release battery and connect phone to pc with usb cable then press Vol- and home and power and put back in battery while. Your computer should get the device.
you flash stockrom using odin.
Sry for that complicated chat, but its not that easy using a browser based chat for that. Also you got more then 1 person tell what to do. Seems not workin that good...
So if something is still not cleat, may be install GTalk for easier chat or teamviewer that i can "show" what i mean.
regards
Click to expand...
Click to collapse
sorry for responding late i tried all that you said but no luck.
i am beginning to suspect it is the problem of the cable or of the phones jack
Hey ,
Just install Kies and uninstall that USB driver . Download files exept .pit and try again . If boot is force closing , go to recovory mode . It should work . Worked in my case
Sent from my GT-S5300 using xda app-developers app
sorry everyone for the late reply
I had gone on a long trip on my way back I also bought an USB cable then it worked perfect ,and I flashed stock Rom with Odin. Alright
Thanks
Now I have a new query can I upgrade my galaxy pocket to jelly bean.
Please help

Device bricked - Qualcomm 9008 port up but ADB does not detect the device

Hello everyone,
It seems that my worst nightmares came up, and got my device bricked while trying to flash it to a stock ROM (had a custom multilingual ROM installed by the chinese seller), and now it's in a strange stage, as Windows detects the Qualcomm port, but adb can't see it.
The adb devices list is in blank, and QPST detects everything, but when trying to flash the device, the error message on the screenshot appears.
Also tried to do it with MiFlash, but didn't worked too.
Any idea about how to solve this?
Thank you in advance for your help.
P.D.: My device is in black screen, so no menu or anything.
P.D.2: Already downloaded the Android SDK in order to try it's ADB, but it didn't worked too.
Now after some research, I found out that the "ADB interface" is not showing in Windows device manager
I tried to install it manually, but can't find a way to get it working, and after the flash, USB debugging was set on, so can't figure out what could be happening...
Is it possible it's completely dead?
Any idea?
Just to say that I have tried multiple combinations while plugging the device to the PC, and didn't worked...
I mean, the PC seems to react, but always with the same end, only shows the Qualcomm port 9008, nothing about the adb...
Getting out of ideas, anyone more has some?
did you start the tool with admin rights?
read a Little bit here
http://zukfans.eu/community/threads/howto-flash-a-stock-zui-rom-zuk-z2-z2131-only.104/
if you have a Z2 pro take this
http://zukfans.eu/community/threads/howto-flash-a-stock-zui-rom-zuk-z2-pro-z2121-only.57/
Zukunft said:
did you start the tool with admin rights?
read a Little bit here
http://zukfans.eu/community/threads/howto-flash-a-stock-zui-rom-zuk-z2-z2131-only.104/
if you have a Z2 pro take this
http://zukfans.eu/community/threads/howto-flash-a-stock-zui-rom-zuk-z2-pro-z2121-only.57/
Click to expand...
Click to collapse
Yeah, I already started the cmd with admin rights, but the problem is that adb does not works, as the device is not turning on.
As you can check in my first post, in the screenshot, after running the "adb devices" command, it doesn't gives any kind of error, just returns a blank list.
Noggin said:
Yeah, I already started the cmd with admin rights, but the problem is that adb does not works, as the device is not turning on.
As you can check in my first post, in the screenshot, after running the "adb devices" command, it doesn't gives any kind of error, just returns a blank list.
Click to expand...
Click to collapse
adb will never recognized it, in 9008 mode or it's called EDL, the only program that recognized the port is QFIL / Miflash. if you get an error when flashing you must reset your phone again to repeat the process by pressing power button for a couple seconds. if your bootloader already unlocked that must be simpler to do, just press power button for a couple minutes until shor vibration then press vol up + vol down and connect to usb at the same time..
arif_kholid said:
adb will never recognized it, in 9008 mode or it's called EDL, the only program that recognized the port is QFIL / Miflash. if you get an error when flashing you must reset your phone again to repeat the process by pressing power button for a couple seconds. if your bootloader already unlocked that must be simpler to do, just press power button for a couple minutes until shor vibration then press vol up + vol down and connect to usb at the same time..
Click to expand...
Click to collapse
Thanks for the info, I've tried the vol + and vol- buttons after the short vibration, and the PC does not detect the device...
Is it there any other way to get the device detected by the PC?
Actually, the only thing the device does, is the following:
After pressing the PWR button for around 5-7 seconds, it makes a short vibration and the notifications led makes a flash in green colour, but nothing more... If you keep pressing it, around 7-8 later, it makes a litte bigger vibration and a flash on green too... And if you continue, it does on, and on, and on...
Any idea? Anyone told me about getting a Xiaomi Deep flash cable, but I'm not sure about if that will work or not...
Noggin said:
Thanks for the info, I've tried the vol + and vol- buttons after the short vibration, and the PC does not detect the device...
Is it there any other way to get the device detected by the PC?
Actually, the only thing the device does, is the following:
After pressing the PWR button for around 5-7 seconds, it makes a short vibration and the notifications led makes a flash in green colour, but nothing more... If you keep pressing it, around 7-8 later, it makes a litte bigger vibration and a flash on green too... And if you continue, it does on, and on, and on...
Any idea? Anyone told me about getting a Xiaomi Deep flash cable, but I'm not sure about if that will work or not...
Click to expand...
Click to collapse
i've already tried xiaomi deep flash cable, and its work on my z2 plus, that's how to force phone into 9008 mode.. and also, dont add space between folder names where your firmware files there or there will always sahara fail
Hey man!
I had the same Problem!
Sahara error, no reaction from device, black screen, port recognized in qfil etc.
I found out that this behaviour of the device means, that it is in EDL-mode.
what helped ma was:
1) Unplug everything.
2) Set up the QFIL Tool completely, but do not hit "Download Content".
3) Try to "reboot" the Zuk Z2 Pro by pressing the power button for several seconds. Kind of resets everything.
4) Plug in USB
5) execute: "adb reboot edl" via adb
6) unplug USB
7) plug in USB and immediately (within a second!) hit the "Download Content" buton, just after it is clickable.
8) dowload should start without sahara error
Hope it works! :good:
Well, finally, I talked with the aftersales dpt from the shop where I got the device, and returned it, and incredibly it seems it was defective.
The guy from the tech dpt said that it wasn't supposed to die that way, so they returned me a brand new device, and fortunately it's up to date with ZUK's last official ROM.
Thank you everyone for your ideas and help, now I can enjoy this great device
My Zuk Z2 plus got stuck after TWRP, I need help badly.
sirmclord said:
Hey man!
I had the same Problem!
Sahara error, no reaction from device, black screen, port recognized in qfil etc.
I found out that this behaviour of the device means, that it is in EDL-mode.
what helped ma was:
1) Unplug everything.
2) Set up the QFIL Tool completely, but do not hit "Download Content".
3) Try to "reboot" the Zuk Z2 Pro by pressing the power button for several seconds. Kind of resets everything.
4) Plug in USB
5) execute: "adb reboot edl" via adb
6) unplug USB
7) plug in USB and immediately (within a second!) hit the "Download Content" buton, just after it is clickable.
8) dowload should start without sahara error
Hope it works! :good:
Click to expand...
Click to collapse
I will tell my issue
I bought this device this July month, I was encouraged seeing you guys did a lot of flashing, I thought I could flash myself but it became a nightmare now.
I am not that much technical so please bare my usage of words below, but I need a real help.
I was doing the basic TWRP for getting the AICP ROM 12.1 but after wiping the data from TWRP my device doesnt get recognized for the Sideload and I did whatever I can but it doesnt detect my phone, so I am having a screen with Start "Green" which is showing the device status as unlocked and when I click on Recovery it goes to the Zuk logo and doesn't have any sign after that.. stuck really
I tried using QFIL but my device detects as 900H but not 9008 also adb doesn't detect my device at all after this.
I think I really did a hard brick of my device.
I dont want to loose hope, I want your help really badly.
For those of you who had the same problem don't give up! I was in that same situation and I solved by putting my phone on EDL via this method
https://www.youtube.com/watch?v=2m44xKog-dI
After plugging the phone for the second time and QFIL recognize as EDL mode I clicked on download content as fast as I could so it started to flash the ROM that I spent like 10h trying to figure a way to do it lol. Anyways, the procedure is the same as putting into EDL via adb fastboot, the only difference is that you make it through a "fake" deep flash cable as that guy in the video shows.

Categories

Resources