Database Develop

Moto X bootup issue

Totally stock XT1058 on Rogers, locked bootloader, no root, phone was encrypted under KK. Updated to 5.1 OTA a couple of weeks ago, and everything has been fine until today.
Installed a couple of app updates (Nova launcher, Falcon Pro, Google, Google keyboard), discovered my launcher had disappeared (as in exiting the play store left with me with no home screen or ability to access app tray). I rebooted in the hope this would help.
The phone now won't get into the launcher. Instead, the boot animations display, I get prompted for my PIN/encryption key, and the animation continues, but the screen stays blank. I've occasionally seen glimpses of the home screen, but it's non-responsive.
The phone is alive as I can call it and it will ring, but I can't answer. It is however running very warm.
I can power down the phone by long-pressing power button and touching the "Power off" prompt.
I can bring up the fastboot menu by holding volume down for a few seconds and tapping the power button:
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
As it's unclear, the first two lines read:
Code:
AP Fastboot Flash Mode (S)
30.BE (sha-34b7ccb, 2015-04-22 12:57:17)
Below this is information about the memory, and that the Device is Locked, Status code 0.
Blue lines are the boot options.
However, selecting either the "Normal Powerup" or "Factory" options just kicks off the same sequence (i.e. boot animations, prompt for PIN/encryption key, more boot animations, blank screen). Selecting the "Recovery" option just gives me the broken android screen with "no command" (following the "External Reset" instructions here).
The screen obviously works, as I can enter the PIN and select the power off prompt.
Any suggestions on how to troubleshoot?

Might be a corrupted SystemUI. A factory reset should do the work.

I have a similar problem only I updated to the 5.1 with the official OTA today.
Phone also encrypted in KK but on first boot said data got corrupted and prompted for factory reset on screen which had an unresponsive button...
Reboot basically lead to asking for password and then the same situation of some animation then blank screen.
For me loading up the fastboot menu works but trying to go into recovery for wipe just leads to a screen saying No Command

TaroLaw said:
For me loading up the fastboot menu works but trying to go into recovery for wipe just leads to a screen saying No Command
Click to expand...
Click to collapse
Yeah, that is what happens to me. Edited the original post to clarify this.

EmilianoTalamo said:
Might be a corrupted SystemUI. A factory reset should do the work.
Click to expand...
Click to collapse
Selecting "Factory" just kicks off the boot to blank screen and a warm running phone again.

thedosbox said:
Selecting "Factory" just kicks off the boot to blank screen and a warm running phone again.
Click to expand...
Click to collapse
So playing around, I managed to factory reset my phone by just using fastboot to wipe my phone with the fastboot -w command.
It almost seemed like it didn't work but then I decided to try and let it reboot and I guess the wipe ended up being successful in the end.
Maybe it'll work for you?

TaroLaw said:
So playing around, I managed to factory reset my phone by just using fastboot to wipe my phone with the fastboot -w command.
It almost seemed like it didn't work but then I decided to try and let it reboot and I guess the wipe ended up being successful in the end.
Maybe it'll work for you?
Click to expand...
Click to collapse
Good call, thanks - that worked.
For anyone having similar issues:
a) Power off the phone
b) Restart by holding the volume down key for a few seconds, then hitting power. This will boot you into the fastboot menu.
c) Connect the phone to your PC
d) On the PC, open a command prompt as an admin and issue the command "fastboot devices" to check the phone is visible
e) Issue the command "fastboot -w" to clear userdata and cache
f) Wait for the phone to reboot

Locked and not rooted Moto X stuck on the boot screen

Here is the situation :
I have a Moto X (1st generation), it's completely genuine, never been rooted or unlocked.
I was using Whatsapp and Airbnb apps, when suddenly a message pop up on the screen, it was like "The service com.google.IdontRememberWhat**** stopped". So I pressed the only option that was "OK", and this message instantly appeared again. Then there was a wild battle between my phone and I which consisted of an endless succession of pop-up/OK. My phone won, and I decided to turn it off which was the only thing I could do at that point.
Now, the situation is that my phone doesn't want to boot. When I start it, it stays 1-2 minutes on the boot screen with the Motorola logo, then it reboots. Endlessly. I accessed the bootloader by holding "power" and "Vol-".
The screen looks like this :
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
- If I try the option "Factory", the phone goes on its reboot-logo screen loop
- If I try the option "Recovery", I get this screen :
On this screen :
- If I try the option "wipe data/factory reset", the screen is stuck on
"-- Wiping data...
Formatting /data..."
for like 1 minute and the phone enters in its endless reboot-logo screen loop.
- If I try the option "wipe cache partition", the screen is stuck on
"-- Wiping cache...
Formatting /cache..."
for like 1 minute and the phone enters in its endless reboot-logo screen loop.
So, at this point what are my options apart from playing baseball with the phone ?
I see that in the recovery menu there are these two options "apply update from sdcard" and "apply update from ADB". Does anyone know if I can save my phone with these options (taking into account that my phone is locked and not rooted) ? And how ?
Thanks

Apprentice.Soft said:
Here is the situation :
I have a Moto X (1st generation), it's completely genuine, never been rooted or unlocked.
I was using Whatsapp and Airbnb apps, when suddenly a message pop up on the screen, it was like "The service com.google.IdontRememberWhat**** stopped". So I pressed the only option that was "OK", and this message instantly appeared again. Then there was a wild battle between my phone and I which consisted of an endless succession of pop-up/OK. My phone won, and I decided to turn it off which was the only thing I could do at that point.
Now, the situation is that my phone doesn't want to boot. When I start it, it stays 1-2 minutes on the boot screen with the Motorola logo, then it reboots. Endlessly. I accessed the bootloader by holding "power" and "Vol-".
The screen looks like this :
- If I try the option "Factory", the phone goes on its reboot-logo screen loop
- If I try the option "Recovery", I get this screen :
On this screen :
- If I try the option "wipe data/factory reset", the screen is stuck on
"-- Wiping data...
Formatting /data..."
for like 1 minute and the phone enters in its endless reboot-logo screen loop.
- If I try the option "wipe cache partition", the screen is stuck on
"-- Wiping cache...
Formatting /cache..."
for like 1 minute and the phone enters in its endless reboot-logo screen loop.
So, at this point what are my options apart from playing baseball with the phone ?
I see that in the recovery menu there are these two options "apply update from sdcard" and "apply update from ADB". Does anyone know if I can save my phone with these options (taking into account that my phone is locked and not rooted) ? And how ?
Thanks
Click to expand...
Click to collapse
download the firmware for your phone and flash it in the fastboot mode
Download your firmware Here
checkout this LINK

Rohit99 said:
download the firmware for your phone and flash it in the fastboot mode
Download your firmware Here
checkout this LINK
Click to expand...
Click to collapse
Thanks for the reply !
I already went through this forum and tried the solution on your link, unfortunately without success :
- For the 1st method, RSD Lite doesn't recognize my phone.
- For the 2nd method, I have just no idea what I have to do. It only says it's easier, and gives a bunch of code lines that I have no idea what to do with as at this point I have no access to my phone files.
Any idea ? Maybe there is a trick for this much easier 2nd method.

Huawei Ascend P7 - bootloop singular problem :(

Hello, my Huawei P7 during automatic update does not start up again. I can't go into download mode or fastboot . I have tried all ways , with the attached USB cable , pressing pwr + vol up, vol down + pwr , pwr + vol up and down . Always returns to the same place: Software install failed!
I managed to use this instruction (http://www.carbontesla.com/2015/07/guide-restore-ascend-p7-b805-lollipop-to-b609-kitkat-firmware/) to do downgrade using the transition pack , then downgrade to the B609 and unlock bootloader according to the instructions (http://forum.xda-developers.com/ascend-p7/general/unlock-bootloader-huawei-ascend-p7-l10-t2830641)
Everything I've done via SD card by force update
After bootloader unlock
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
Just trying to get fastboot or download mode by pressing pwr + vol-
https://www.youtube.com/watch?v=Ba0CcdiXQj0
pwr + vol+
https://www.youtube.com/watch?v=OaVlNfwtxKs

racesupport said:
Hello, my Huawei P7 during automatic update does not start up again. I can't go into download mode or fastboot . I have tried all ways , with the attached USB cable , pressing pwr + vol up, vol down + pwr , pwr + vol up and down . Always returns to the same place: Software install failed!
I managed to use this instruction (http://www.carbontesla.com/2015/07/guide-restore-ascend-p7-b805-lollipop-to-b609-kitkat-firmware/) to do downgrade using the transition pack , then downgrade to the B609 and unlock bootloader according to the instructions (http://forum.xda-developers.com/ascend-p7/general/unlock-bootloader-huawei-ascend-p7-l10-t2830641)
Everything I've done via SD card by force update
After bootloader unlock
Just trying to get fastboot or download mode by pressing pwr + vol-
https://www.youtube.com/watch?v=Ba0CcdiXQj0
pwr + vol+
https://www.youtube.com/watch?v=OaVlNfwtxKs
Click to expand...
Click to collapse
Have you thought of taking it to the repair shop? Because I'm thinking that this might be more than just a software problem.

TheSproker said:
Have you thought of taking it to the repair shop? Because I'm thinking that this might be more than just a software problem.
Click to expand...
Click to collapse
I think so too but first I wanted to try to somehow rescue... no results

racesupport said:
Hello, my Huawei P7 during automatic update does not start up again. I can't go into download mode or fastboot . I have tried all ways , with the attached USB cable , pressing pwr + vol up, vol down + pwr , pwr + vol up and down . Always returns to the same place: Software install failed!
I managed to use this instruction (http://www.carbontesla.com/2015/07/guide-restore-ascend-p7-b805-lollipop-to-b609-kitkat-firmware/) to do downgrade using the transition pack , then downgrade to the B609 and unlock bootloader according to the instructions (http://forum.xda-developers.com/ascend-p7/general/unlock-bootloader-huawei-ascend-p7-l10-t2830641)
Everything I've done via SD card by force update
After bootloader unlock
Just trying to get fastboot or download mode by pressing pwr + vol-
https://www.youtube.com/watch?v=Ba0CcdiXQj0
pwr + vol+
https://www.youtube.com/watch?v=OaVlNfwtxKs
Click to expand...
Click to collapse
Hi!
Try to get into bootloader mode WITHOUT any usb cable. If you do not get into bootloader, upload a video. I think there is a chance your phone is not dead

https://www.youtube.com/watch?v=flVRtOqIYU4

try to install b800 again
how is the battery? (charged ?)

Just downloading HUAWEI_Sophia-L10C900B839_Firmware_Europe_Android5.1.1_EMUI3.1.zip
Battery fine, charged to 100%
Ps
Phone is after update, still this same screen "software install failed"
During the update phone was restart after 19% and start updating again.
Dead?
Thanks for any help. I think thread is exhausted and phone Is dead as well.

Hard bricked(?)

I flashed my Lenovo A7000a (MT6752) to update to android 6.0 (it was rooted)with the "format all then download" option on SP tool. Now when i try to switch it on it shows a blank screen and dies. When connect my phone (power button down ofcourse) to pc with the SPTool download button activated, I am able to flash my phone again, but result is the same. The autorun for LenovoSuite even pops up when I connect the phone to PC. I am thinking that I may have flashed the wrong/bad ROM to my phone, will update again
Update: Flashed with "download only" option with an older ROM, phone is able to boot, but with the same blank screen, and I can press the power button to turn the screen off, or on. Not able to boot into recovery mode, meta mode, or whatever anything, just a white blank screen.

hi
guolehhh said:
I flashed my Lenovo A7000a (MT6752) to update to android 6.0 (it was rooted)with the "format all then download" option on SP tool. Now when i try to switch it on it shows a blank screen and dies. When connect my phone (power button down ofcourse) to pc with the SPTool download button activated, I am able to flash my phone again, but result is the same. The autorun for LenovoSuite even pops up when I connect the phone to PC. I am thinking that I may have flashed the wrong/bad ROM to my phone, will update again
Update: Flashed with "download only" option with an older ROM, phone is able to boot, but with the same blank screen, and I can press the power button to turn the screen off, or on. Not able to boot into recovery mode, meta mode, or whatever anything, just a white blank screen.
Click to expand...
Click to collapse
i have this problem!!!!
anyone can't help us??

alirezakiani19 said:
i have this problem!!!!
anyone can't help us??
Click to expand...
Click to collapse
Try this:
In the spflash tool go to the “Option” tab, then go to “Download”, and put a “tick” in the “DA DL All with Checksum.
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
Hope this will work for you

it asking that ...plz check your loadmatches with error

i have the same problem like you anyone help ??? Now my phone just display white blank screen . I was try to flash many times . . include format all + download but it's still blank screen .

guolehhh said:
I flashed my Lenovo A7000a (MT6752) to update to android 6.0 (it was rooted)with the "format all then download" option on SP tool. Now when i try to switch it on it shows a blank screen and dies. When connect my phone (power button down ofcourse) to pc with the SPTool download button activated, I am able to flash my phone again, but result is the same. The autorun for LenovoSuite even pops up when I connect the phone to PC. I am thinking that I may have flashed the wrong/bad ROM to my phone, will update again
Update: Flashed with "download only" option with an older ROM, phone is able to boot, but with the same blank screen, and I can press the power button to turn the screen off, or on. Not able to boot into recovery mode, meta mode, or whatever anything, just a white blank screen.
Click to expand...
Click to collapse
Is SPft tick Da/DL with checksum.am sure it will be fixed

aswinp222 said:
Is SPft tick Da/DL with checksum.am sure it will be fixed
Click to expand...
Click to collapse
Yes it is ticked still the same. I too have white screen after flash

i can help you...i fixed this .
guolehhh said:
I flashed my Lenovo A7000a (MT6752) to update to android 6.0 (it was rooted)with the "format all then download" option on SP tool. Now when i try to switch it on it shows a blank screen and dies. When connect my phone (power button down ofcourse) to pc with the SPTool download button activated, I am able to flash my phone again, but result is the same. The autorun for LenovoSuite even pops up when I connect the phone to PC. I am thinking that I may have flashed the wrong/bad ROM to my phone, will update again
Update: Flashed with "download only" option with an older ROM, phone is able to boot, but with the same blank screen, and I can press the power button to turn the screen off, or on. Not able to boot into recovery mode, meta mode, or whatever anything, just a white blank screen.
Click to expand...
Click to collapse
I think you already fixed the issue..
If not , email me @sreekanth[email protected]

i have exactly same problem....
if you fixed it please guide me too
Regards

When you connect your phone with pc, no need to press any button, just connect the cab

hgiang0808 said:
When you connect your phone with pc, no need to press any button, just connect the cab
Click to expand...
Click to collapse
Do you fix it already???

trikZ03 said:
Do you fix it already???
Click to expand...
Click to collapse
I did it many times. Just need install driver, then click "Download" button in flashtool then connect cab. Flashtool will run!

The phone stuck after trying to install rom

Hello! I have tried to install the THE GALAXY PROJECT rom
first I intalled TWRP
I try to wipe the phone and I got a massage:
"failed to mount data internal"
afterwards I anyway tried to intalled the rom and after the Installation done the phone try to reboot and failed. I got some massage about permission and with botton to reboot, and I clicked.
anyway now my phone stuck on circle with lightning.
I try to enter recovery mode or download mode and didn't make it.
please help.
(sorry for my english, I'm not a native)
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}

jd14771 said:
At some point, the Download mode trigger as changed.
to get download mode:
-Turn phone OFF
-HOLD VOLUME DOWN + BIXBY
-Plug phone into computer with USB cable while HOLDING the above BUTTONS.
-You should be in Download Mode.
Click to expand...
Click to collapse
thank you.
before I saw you comment I click on POWER + BOTTON DOWN.
now my phone stuck on the first screen (samaung galaxy note9..)
I want to try you suggestion but how I turn the phone OFF? he stuck on screen.
also I'm trying to Hold VOLUME DOWN + BIXBY and connect the cable like you said and nothing happened..
if I holding VOLUME DOWN + BIXBY + POWER the screen changed to black for second and again show me the 'samaung galaxy note9' screen.

yamar8 said:
thank you.
before I saw you comment I click on POWER + BOTTON DOWN.
now my phone stuck on the first screen (samaung galaxy note9..)
I want to try you suggestion but how I turn the phone OFF? he stuck on screen.
also I'm trying to Hold VOLUME DOWN + BIXBY and connect the cable like you said and nothing happened..
if I holding VOLUME DOWN + BIXBY + POWER the screen changed to black for second and again show me the 'samaung galaxy note9' screen.
Click to expand...
Click to collapse
your initial issue was that you DIDINT format data when you first flashed twrp. please read dr.ketans guide in the guides and discussion thread.
when the phone reboots by holding vold down and power, very very quickly swap to the DL button combo(vol down + bixby) and plug cable. reflash twrp 3.2.0.0 and follow the instructions. ( when odin fisnishes flashing twrp in the AP slot, DONT let phone boot to home screen or at all. immediately hold vol up +bixby +pwr to enter twrp recovery. then swipe to allow modification and go directly to wipe menu and format data. type yes when asked. go to reboot menu and choose reboot to recovery and flash
N960F_DS_N_PIE_Root_for_OEM_issue_devices_V5.zip)
again please read the guide attentively

jd14771 said:
follow these steps, you must be fast and diligent with the button combinations:
-first, plug phone into computer
-Second, HOLD POWER + VOLUME DOWN until device restarts, as SOON as the screen goes black you must let go of all buttons and immediately hold VOLUME DOWN + BIXBY
-you should be in download mode.
the phone has to be OFF and plugged into a computer BEFORE you hold VOLUME DOWN + BiXBY in order to enter download mode. You can not trigger this while the phone is on.
Click to expand...
Click to collapse
Thank you so much! it is worked!
I am in download mode.
now I will install the twrp again.

bober10113 said:
your initial issue was that you DIDINT format data when you first flashed twrp. please read dr.ketans guide in the guides and discussion thread.
leave cable plugged it.
when the phone reboots by holding vold down and power, very very quickly swap to the DL button combo(vol down + bixby). reflash twrp 3.2.0.0 and follow the instructions. ( when odin fisnishes flashing twrp in the AP slot, DONT let phone boot to home screen or at all. immediately hold vol up +bixby +pwr to enter twrp recovery. then swipe to allow modification and go directly to wipe menu and format data. type yes when asked. go to reboot menu and choose reboot to recovery and flash
N960F_DS_N_PIE_Root_for_OEM_issue_devices_V5.zip)
again please read the guide attentively
Click to expand...
Click to collapse
thanks, I'm trying now.