[Q] Proper diag drivers - HTC One Mini 2

Can anyone help me locate diag drivers for the mini2? Windows64 Os.
Edit*
Disregard, just my lack of windows know how was holding the old drivers up.

Related

Kaiser/TyTn II and QPST?

Hello, I'd like to request information on how to use QPST with my Kaiser via USB. QPST shows 'No Phone' on all ports and I don't seem to be able to enter diagnostic mode.
Any advice would be greatly appreciated. Thanks.
i'm running Vista if that makes a difference...
I also have a PC running XP if that helps.
Nobody will help me?
i am trying to do the same thing, i have gone as far as flashing to jockyw's spl with tty enabled. but i dont know how to put it in qpst diag mode... i am using vista, but also tried under xp, with no change.
I'm trying to do the same thing. I can get the comm ports to show up and use QPST while the phone is in the tri-color bootloader state. QXDM will also works in that state but since the phone is not runing, I get no useful information.
I have not been able to get the com ports to show up with the phone is fully booted like I can with CDMA smart phones by dialing ##DIAG#.
you can get qpst to recognize it in tri color mode? the only way i was able was to put it in download mode by issuing rtask a, and radata 90000000 1. after that i installed the motoq drivers available in the frankenkaiser pack. it shows up in qpst as download mode, but it can not mess with anything because it is in dl mode. if you know how to put it in diag mode, that would be a step for me!
I have installed the wmodem drivers and put the phone in bootloader. But qpst sees nothing. Is there a diagnostic mode similar to a CDMA phone.
does anybody know more about qpst?

[Q] What drivers are needed for Odin?

Please don't unnecessarily kill any more chickens.
Have you tried Android SDK usb drivers? Someone else on the forum said it works.
Thank you for the reply. But it didn't work. Said can't find "USB Gadget"
hi
i had same problem,i installed samsung pc studio package and managed to flash with odin without any problem
following tutorial in the sdk kit, I got "adp" to recognice my phone from a command prompt in USB debug mode. But when I connect in downloading mode, I get this "Gadget Serial" driver issue. Gadget Serial is not one of the drivers in any of the USB driver packages I downloaded. Anyone know where I can get this?
any answers?
i got the same issue and my phone stuck on the samsung screen restarting over and over
I have posted latest x64 drivers from samsung here on this forum. You can try to use them.
Sent from my GT-I9000 using XDA App
Also restart windows with enforce driver signing disabled. Try other usb ports.
Sent from my GT-I9000 using XDA App
Please please can someone help i was using the new 4.01 ics on samsung galaxy s. Now i cannot conect to pc. I Get an error message all the time saying Usb malfunctioned and i cant use odin to revert back or anything. I have looked everywhere tried reinstalling drivers ect but no joy
I know a while has gone by but just in case someone else stumbles on this thread with the same problem or in case you're still looking for an answer try dialing *#7284# which takes you to the PhoneUtil. Under USB section click on MODEM and then click on USB. Give it a try, it should work
there is a direct download for the nexus drivers found here : http://androiddrivers.net/samsung-android-drivers/download-nexus-s-drivers/ , also suggested in another similar post is to clean the usb port of your phone with alcohol and a fine brush(but remove battery if doing so)

[Q] What am I doing WRONG?!

I have a Galaxy tab 7 thru Verizon and I want to install galaxy cubed 3. I first installed drivers from verizon bootstrapper, then put in download mode and plugged in, get device driver not successfully installed and unknown device in zadig.exe. Then tried installing kies, then open tools and install drivers. Kies does not recognize my tab 7, and am told to put into pc studio mode to sync, but drivers seem to install correctly. I put into download mode and plug in, and again device driver not installed correctly and unknown device is shown in zadig.exe. I have uninstalled all drivers and kies and reinstalled more than onece, and this is not working. I am using windows 7. What else can I do? Any expert opinions would be greatly appreciated. I would really like to enjoy the hard work developers here have put in. Thank you!!

[Q] BP Tools drivers

Hi!
I'm trying to connect Moto X in BP Tools mode, but Windows XP cannot find appropriate drivers. I have latest drivers from Motorola website, version 6.2.0 I believe, part of Motorola Device Manager 2.4.3 package. It connects without problems in MTP mode, as well as I do not have any issues with connecting my Motorola XT912 in BP Tools mode.
Any ideas where to get proper drivers or overcome this issue?
Thanks!

Trouble installing HTC USB Modem drivers

I've been able to install the 9k drivers and the normal usb drivers however I can not get my PC to see the USB MODEM and install drivers when I plug it in. Please help. I've tried serial mode, and it still won't recognize.
Northstarr said:
I've been able to install the 9k drivers and the normal usb drivers however I can not get my PC to see the USB MODEM and install drivers when I plug it in. Please help. I've tried serial mode, and it still won't recognize.
Click to expand...
Click to collapse
also having troubles installing drivers... are u on windows 8. im using 8 and cant seem to get them working. anyone?

Categories

Resources