Hello all, while drunk at the beach this weekend I accidentally went into the water with my Touch Diamond in my pocket... stupid... I know, did I mention I was drunk? Anyways, the current issue at hand is what to do with my screwed up cell phone.
I took the backing, battery and SIM card out of the phone and let it dry out as much as I could since the weekend. When I turned it on this morning, the "smart mobility" text appears for a few seconds, but the phone shuts off shortly after that. Do batteries usually break from water damage, as well?
If anyone has any advice for me I would greatly appreciate it. Does anyone know of a legit place that can repair this? Is there anything I can do to try and remedy this problem? Or would you recommend I just sell/ditch this one and get a new phone? Thanks a lot.
Have you tried charging the battery? that might explain it only booting for a second, the other explanation is that it's fried the ROM chips and only the bootloader works.
It's not looking good, is it under warranty?
Disassemble your Diamond completely (manual floating around somewhere in this forum), clean all pieces using one of these isopropanol-brush-thingies, reassemble, turn it on - and pray. Any year - a new battery might be a good idea. No promises on anything of that though. The diamond is a very integrated piece of technology and you might have short-circuited something on one of the PCBs really. No guarantee that everything will work as usual even if the device comes up as well.
Warranty seems to be out of the question - I guess virtually any repair center will notice residue of loads of salt water on the first look inside...
That's true, I meant to say insurance, heh.
Strip it down Salt water is very and I mean very corrosive ! You have nothing to lose and everything to gain by doing this . Waranty repair will be expensive.
Clean with an alchol based cleaner as advised but you must ensure you get all the salt out. To see it boot means that the screen has survived ( Amazed by this ) .
Best of luck , oh and if it does not work are you insured for accidental damage on personal items on your household insurance. This could be the next route
I have the same problem with my Tytn 2. It got wet during the "Oranje" Party in Basel, when the firemen were "cooling" down the fans...
It boots..but as soon as it has booted, you here a lot of "bling..bling..bling.." and it shuts down.. the batterie doesn't charge..
You recommend to open and clean it with alcool? Actually I'm not sure if it was washed by the firemen or by my own alcool .ehhehe..
I have a Diamond now, but if I get it back to work, I would sell it on ebay.
Regards
dajudge01 said:
Warranty seems to be out of the question - I guess virtually any repair center will notice residue of loads of salt water on the first look inside...
Click to expand...
Click to collapse
There is a watersensor inside the diamond. They'll notice that the device has been in the water.
wardy said:
Strip it down Salt water is very and I mean very corrosive ! You have nothing to lose and everything to gain by doing this . Waranty repair will be expensive.
Clean with an alchol based cleaner as advised but you must ensure you get all the salt out. To see it boot means that the screen has survived ( Amazed by this ) .
Best of luck , oh and if it does not work are you insured for accidental damage on personal items on your household insurance. This could be the next route
Click to expand...
Click to collapse
Luckily I was at lake Michigan in Chicago (fresh water), for whatever that's worth, so I'm not really worried about salt corroding anything away. I bought it off eBay unlocked, I did buy insurance but, naturally, I'm pretty sure that this water damage won't be covered.
Sounds like taking it apart and cleaning it might be my best bet. Do you guys think that any cell phone repair place would be able to help me out? Anyone know of a good cell phone repair shop (in the U.S.)? Thanks for the help thus far guys, I really appreciate it
Firstly remove the battery and SIM, please do not try to power up or charge again as you might have already damaged it beyond repair.
Isopropanol or IPA is what you need (100% Alcohol), you can get this from your local chemist for about £5 a bottle.
You need to strip your phone down completely and use an anti static PCB brush to clean the whole lot (Buy it from Maplin), submerge it in a plate of IPA (excluding the screen) while cleaning. As for the warranty sticker remove this by first heating with a hair drier, then uing a Stanley knife point to remove it.
Once it’s all been cleaned and dried in air, re-assemble and power up. If it fails to work take it back for a warranty replacement. As the warranty sticker is intact, and all the evidence of water damage will have been removed, they should replace it for you without a problem.
nairb011 said:
Luckily I was at lake Michigan in Chicago (fresh water), for whatever that's worth, so I'm not really worried about salt corroding anything away. I bought it off eBay unlocked, I did buy insurance but, naturally, I'm pretty sure that this water damage won't be covered.
Sounds like taking it apart and cleaning it might be my best bet. Do you guys think that any cell phone repair place would be able to help me out? Anyone know of a good cell phone repair shop (in the U.S.)? Thanks for the help thus far guys, I really appreciate it
Click to expand...
Click to collapse
Pretty sure? I would check if I was you before doing anything else with it. If insurance doesnt cover water damage, what does it cover? Phone insurance is so expensive i thought they covered everything like theft and accidental damage, I thought the idea was a warranty wont cover you if you break the phone but insurance will.
I'm thinking it may be an idea to check before you do anything else so they dont say "Well we cover water damage, but now youve taken apart the phone we cant cover you"
Antimus said:
Have you tried charging the battery? that might explain it only booting for a second, the other explanation is that it's fried the ROM chips and only the bootloader works.
It's not looking good, is it under warranty?
Click to expand...
Click to collapse
Seriously you are not hoping warranty will cover "swimming with the diamond"...
imranbashir_uk said:
all the evidence of water damage will have been removed, they should replace it for you without a problem.
Click to expand...
Click to collapse
All the evidence, that is, apart from the water-sensitive tab which I am assuming you didn't know about...? (behind the tab for attaching a strap)
Mathew
webmice said:
Seriously you are not hoping warranty will cover "swimming with the diamond"...
Click to expand...
Click to collapse
or doese he mean "Swimming Diamond" ... Is that a new feature we overlocked? I think it's time for another entry in the tweaklist... *rofl*
My warranty does not cover accidental water damage, that is for sure.
I charged the battery up over the weekend and tried turning it back on, and, to my utter amazement, the phone completely powered on. I got to all of my menus and was able to use all of the programs that I opened, even the WiFi worked.
However, the functionality of the touch screen is quite screwed up. I don't know if its shorting out or what but there are basically "ghost taps" and other unintentional actions happening all the time. For example, if I were to just leave it at the home screen it would eventually scroll to another menu, open the start pull-down menu, automatically open the calendar and start doing random ****, etc.
Does anyone know how to fix the touch screen or have any ideas on how to replace one? I have a faint hope that this thing might not be beyond saving.. thanks a lot people
nairb011 said:
Does anyone know how to fix the touch screen or have any ideas on how to replace one? I have a faint hope that this thing might not be beyond saving.. thanks a lot people
Click to expand...
Click to collapse
Maybe try to re-calibrate the touch screen?
Don't give up hope, sometimes these things can take days, even weeks to fully dry and become functional. My mom had a sony ericsson somethingorother that she loved, dropped in the tub, didn't work for like a month or more... She'd check it every week or so to see, and slowly the features started coming back... Little by little, more and more buttons would respond (without activating 2 or 3 at a time). Well, long story short (too late?) works 100% now. I don't think water damage is a reparable occurrence, but DON'T sell your Diamond for parts or anything like that, keep it around and check back periodically. Best of luck.
there is a little white sticker onto the battery.
If it goes RED it shows HTC that the Phone/Battery went into the water.
This allows HTC to avoid repair "sunk" phones
deuillevent said:
there is a little white sticker onto the battery.
If it goes RED it shows HTC that the Phone/Battery went into the water.
This allows HTC to avoid repair "sunk" phones
Click to expand...
Click to collapse
Should also be one on the phone... If not, there's your solution. New battery + deny any water damage = Free replacement.
Black93300ZX said:
Should also be one on the phone... If not, there's your solution. New battery + deny any water damage = Free replacement.
Click to expand...
Click to collapse
See post #12
Haha you're all over it... Yeah, I had a feeling they'd have something in the phone, they'd never make it THAT easy.
Hello there,
I've been trying to fix my G1's digitizer for some time now, and it hasn't been too successful. When I acquired the G1, it had no battery cover, banged up covers, and a bulging battery. Since then, I've done a full swap of the housing (entire case, new battery, hardware buttons, LCD, ribbons, and digitizer) and still no results with the digitizer detecting any touch input on the phone.
If anyone's skilled to help repair my G1, can you please assist me with this? I'm willing to ship the phone out and pay accordingly depending on how severe the issue is, and whether more parts need to be replaced.
Or, if there is a way to get professional repairs (maybe even HTC accepting to repair it), how much would it cost to get it functional? I'm at a loss to what is wrong, considering i replaced everything short of the actual board components.
Try this.
Hello everyone!
I bought a Xperia Z1 two weeks ago, and it was the best phone I have ever had.
However my idiot brother Managed to crack the Digitizer a few days back, the display is still working and the phone powers up but the touch panel is unresponsive.
(He was playing with one of those Heavy Snake Egg magnets, he threw the magnet into the air, and landed right on my phone. I'm surprised the Display is still working. )
Anyways, I was wondering if anyone here has replaced only the Touch Panel. I know on the Xperia Z1 its fused with the LCD, however with a machine like the Scotle PR-1000 its possible to separate the LCD from the touch panel.
Here is the link to a video showing the process: https://www.youtube.com/watch?v=h8bZi3FreMk
Now I have a few questions such as:
-With this method, wont the LCD display be scratched up as well?
-When I replace the touch screen with a new touch panel using this method, will it look normal? Or will it look like it has been opened and repaired?
-With a new digitizer, is the phone still waterproof capable? (I dont really care about the waterproof capabilities that much anyways.)
Thanks!
Can anyone help me?
You could just replace the entire display module, digitizer, LCD, and all. This would be the cleaner and easier way of replacing it with fewer potential problems. As far as waterproofing goes, I am not sure. Those are sort of uncharted waters (no pun intended) as far as repairs go. If I were you, I would assume not just to be on the safe side, until further knowledge presented itself. I hope this info helps!
FOr the past few days thats what I was thinking.
Especially since where I live most Cellphone "technicians" are just people with a very limited knowledge of electronics, and would most probably mess up the phone even further.
after placing a few calls to some shops I managed to find a replacement LCD+Digitizer+Frame, but I do not know how good the quality of the replacement unit would be.
Dear WEM97 and other users,
I have the same problem as Akash434. Could you please briefly elaborate on what the (potential) problem could be with just replacing the Digitizer. I can't really decide what to replace the LCD+Digitizer or only Digitizer. I understand replacing the whole LCD unit along is a far, far easier process. But cost wise it's also almost the double (atleast where i live).
Upon removing the Digitizer, should the old glue be removed (if any). What kind of glue should I use to stick the new Digitizer? Will u see that there was glue used? These are just a few questions I am struggling with.
Your help is greatly appreciated.
PS: I apologize for any grammar mistakes. English is not my native language.
you can't do this without a professional machine
https://www.youtube.com/watch?v=yMj-aWbttJk
This is my video and the description will send you to the links to fix it yourself
Otherwise get a shop to fix it... although most regular shops won't fix it... or get sony to fix it if you wanna continue your warranty
Place the phone on a heatable-3dprinter-bed and warme it up the temperature you want - digitizer was falling of the display last time i repaired my z1. I heated it up to disassemble. Now it is cracked again and i just don´t know how to glue the digitizer on... If i would change digitizer
Hi All,
I've been doing repairs for a little while. But every time I've done a screen repair I've replaced the whole assembly. However recently I decided to buy an LCD separator to hopefully cut my costs. However every attempt I've made so far hasn't gone well. I keep slicing the wire between the first layer and the rest of the lcd, rather than between the glass and the lcd.
I was wondering if you guys had any advice you could share, am I better off starting away from the display cables and working towards them or the other direction? Or is it an issue with the temperature, I've been working at about 85°C is this too hot or too cold?
Any help or other advice would be greatly appreciated.
All the best
Will
bobjohnsonandco said:
Hi All,
I've been doing repairs for a little while. But every time I've done a screen repair I've replaced the whole assembly. However recently I decided to buy an LCD separator to hopefully cut my costs. However every attempt I've made so far hasn't gone well. I keep slicing the wire between the first layer and the rest of the lcd, rather than between the glass and the lcd.
I was wondering if you guys had any advice you could share, am I better off starting away from the display cables and working towards them or the other direction? Or is it an issue with the temperature, I've been working at about 85°C is this too hot or too cold?
Any help or other advice would be greatly appreciated.
All the best
Will
Click to expand...
Click to collapse
Deleted