Nexus 6 - WiFi SpeedTest Slower than should be. - Nexus 6 Q&A, Help & Troubleshooting

I'm not sure if this is a networking issue or phone issue, but I think I got this narrowed down to a phone issue.
I currently have a 105mbps plan through Comcast and all is working well except my Nexus 6 WiFi SpeedTest maxes out at around 20-22mbps.
Currently routing with a WRT1200AC Router with both 2.4 and 5ghz bands enabled.
I am aware the Nexus 6 supports 802.11ac; therefore I connected to my 5ghz band network. The nexus shows i'm getting a solid 360mbps connection to the router. However when doing a SpeedTest it caps at 20-22mbps (I should be getting around 105mbps). I suspect no issue with the router as I tested with a 802.11ac supported laptop and was screaming past my 105mbps speed. Based off some google searches I found that possible causes were maybe some power saving features, those have been turned off.
Troubleshooting I have done:
- Moved my 5ghz band to different channels
- Tried different 5ghz channel widths
- Tested speed on 2.4ghz band (Same Results)
- Tested Another Nexus 6 (I tried running a speedtest with a family members N6 running pure stock rom/unrooted and same results as with my Custom Rom'd N6)
- Disabled Carrier Radio leaving only wifi on.
- Reboot Phone, Router, toggled wifi Off and on.
Any other suggestions? It would be pretty disappointing of Google / Motorola if this was the result of hardware capabilities.

Select a different server on Speed Test.

not seeing that issue here...

graydiggy said:
Select a different server on Speed Test.
Click to expand...
Click to collapse
Tried a couple different servers, same outcome
uicnren said:
not seeing that issue here...
Click to expand...
Click to collapse
OK thanks for looking!
hmmmm

Related

WiFi issues on stock

I have issues on Wi-Fi with my one where with my Samsung glide no problems . I have a Belkin router wireless N and it normally works fine but with the one I get occasional drops and reconnects. Anyone else have this issue. I am on stock rogers. My Wi-Fi has security enabled as well.
******************************
HTC ONE (Stock so far) Just got 2013-04-21
Samsung Captivate Glide
Installed:
CWMR5x_i927_recovery.tar.md5
ICS 4.0.4 LiteRom 0.9.0
LiteKernel
So nobody else has issues with their one and WIFI? It just works perfectly?
******************************
HTC ONE (Stock so far) Just got 2013-04-21
Samsung Captivate Glide
Installed:
CWMR5x_i927_recovery.tar.md5
ICS 4.0.4 LiteRom 0.9.0
LiteKernel[/QUOTE]
Did you turn on Power Saver and Sleep Mode? Click the Power Saver mode in the Power menu in Settings. You can select what Power Saver controls. Untick Data Connection, and if you want, turn off Sleep Mode as well.
I have noticed some issued. I have the developer edition and upgraded from a nexus 4. There seems to be issues with the One releasing wifi and reconnecting to data or vice versa.
In some cases, i know i am clearly out of range for a wifi network, such as the top floor of my office, yet it picks it up and connects without data since i assume i am out of range. For now i just manually control it as its pretty rare, but fir sure not something i have ever experienced before.
Sent from my HTC One using xda premium
v0yeur said:
I have noticed some issued. I have the developer edition and upgraded from a nexus 4. There seems to be issues with the One releasing wifi and reconnecting to data or vice versa.
In some cases, i know i am clearly out of range for a wifi network, such as the top floor of my office, yet it picks it up and connects without data since i assume i am out of range. For now i just manually control it as its pretty rare, but fir sure not something i have ever experienced before.
Sent from my HTC One using xda premium
Click to expand...
Click to collapse
Agreed this is what I am seeing.I have disabled power saving and the other option to turn off data when sleeping and yet periodically the wifi just drops as I am viewing some wifi video streaming. It is weird I switch off the WiFi and use data and all is fine. I do not know if it is an incompatibility with my router. That's why I posted here to see if anyone else is seeing similar issues.
Also is there a way to set a manual Ip? was wondering if that may help as have heard issues of other phones having issues with DHCP via wifi.
dudejb said:
Agreed this is what I am seeing.I have disabled power saving and the other option to turn off data when sleeping and yet periodically the wifi just drops as I am viewing some wifi video streaming. It is weird I switch off the WiFi and use data and all is fine. I do not know if it is an incompatibility with my router. That's why I posted here to see if anyone else is seeing similar issues.
Also is there a way to set a manual Ip? was wondering if that may help as have heard issues of other phones having issues with DHCP via wifi.
Click to expand...
Click to collapse
I ordered a new AC router and will see if that works better and if I still get wifi drops. I am hoping it is my old cheap router giving me issues.
dudejb said:
I ordered a new AC router and will see if that works better and if I still get wifi drops. I am hoping it is my old cheap router giving me issues.
Click to expand...
Click to collapse
Well I got the ASUS RT-AC66U and now the Wireless 2.4GHZ works great but the phone will not connect at 5Ghz, so much for AC that only operates at that frequency. I heard other people are having this issue as well from my searches on this forum and the web. Kind of sucks that my router has the latest firmware and still has this issue with this phone. I did notice that there was a beta firmware on Asus's site but I am iffy on trying a Beta Firmware on my Router when all other devices are working great and so is the phone on the 2.4ghz. Great range with this router as well. Sucks that I can not use the 5Gz on the phone though. Tried on 2 other Devices that support 5Gz and it is working great on them. I gave 2 different names for the 2.4Ghz and the 5Ghz to tell them apart, but no go on this phone.
JB
here's my take on the whole wifi thing with htc one. either the wifi chip is too picky or it's too new for the older routers. i couldn't get a wifi to stay connected using my old D-Link DIR-655 router from years ago. All other devices had no problems except this phone so that's a bummer. I then picked up the Asus RT-AC66U and immediately flashed the latest beta firmware. Performance and range is flawless on the 2.4GHz band for this router. 5GHz works as well if i'm close but it just doesn't have the range of the 2.4GHz for this phone so I've been sticking with 2.4GHz.
I actually wanted the just announced RT-AC68U but couldn't wait any longer as there's no eta on the release for it.
dorezen said:
here's my take on the whole wifi thing with htc one. either the wifi chip is too picky or it's too new for the older routers. i couldn't get a wifi to stay connected using my old D-Link DIR-655 router from years ago. All other devices had no problems except this phone so that's a bummer. I then picked up the Asus RT-AC66U and immediately flashed the latest beta firmware. Performance and range is flawless on the 2.4GHz band for this router. 5GHz works as well if i'm close but it just doesn't have the range of the 2.4GHz for this phone so I've been sticking with 2.4GHz.
I actually wanted the just announced RT-AC68U but couldn't wait any longer as there's no eta on the release for it.
Click to expand...
Click to collapse
I used to have a Belkin Wifi-N router cost me about 40$ on sale and it used to work with my old Samsung but could not connect and stay connected on my One (Single was not to strong on top floor of house as well). It kept dropping WIFI after a few minutes on One and was really annoying. The RT-AC66U works great at the 2.4Ghz and I am tempted to try the Beta Firmware that you are using but I hear it slightly drops the range on the 2.4Ghz and all my other devices (WD-TVlive) are working great streaming 1080P from 3 floors up (Routers in Basement). Question for you, since you flashed the Beta firmware and can connect at 5Ghz are you hitting the 400Mb speed when you connect at close range. If you click on your connected network on phone it shows you the connection speed.
dudejb said:
I used to have a Belkin Wifi-N router cost me about 40$ on sale and it used to work with my old Samsung but could not connect and stay connected on my One (Single was not to strong on top floor of house as well). It kept dropping WIFI after a few minutes on One and was really annoying. The RT-AC66U works great at the 2.4Ghz and I am tempted to try the Beta Firmware that you are using but I hear it slightly drops the range on the 2.4Ghz and all my other devices (WD-TVlive) are working great streaming 1080P from 3 floors up (Routers in Basement). Question for you, since you flashed the Beta firmware and can connect at 5Ghz are you hitting the 400Mb speed when you connect at close range. If you click on your connected network on phone it shows you the connection speed.
Click to expand...
Click to collapse
unfortunately with the beta firmware on 5GHz band, the fastest i am able to connect with this phone is around 87Mbps and it still feels slow compared to 2.4GHz. mind you this is me checking the speed by standing right next to the router with my phone. on 2.4GHz the fastest speed i can get is 72Mbps but the range is great. i hope asus is able to release newer firmware that will help increase the speed and range of this router at 5GHz but it's probably not possible. i still think it's the AC chipset/driver in this phone that's preventing the wireless from achieving maximum speed. in comparison, my dell latitude notebook is able to connect at 450Mbps at 5GHz with on wireless N. THat's with the intel wifi chipset which has always been imo the best in compatibility and performance. i look forward to the day when i can rock a smartphone with intel all in one chipset.
I am also connected at 72mb and at 2.4ghz it connects great. I am going to leave it like this. I find the range on the Asus router is amazing. It sure beats all other routers.

Wifi Issues?

Is anyone else having an issue where your device will be hooked up to a wifi network, will still indicate you're connected but no data will sync? I email myself and nothing happens. Happens with FB, Email, Gmail, and Voice Controls don't work.
ShamanicEnzan said:
Is anyone else having an issue where your device will be hooked up to a wifi network, will still indicate you're connected but no data will sync? I email myself and nothing happens. Happens with FB, Email, Gmail, and Voice Controls don't work.
Click to expand...
Click to collapse
I have that issue with my gNex and my wife's DNA on our home network. I don't think it is necessarily this phone, but I am not convinced (yet) that it is my router, either...
TheKaz said:
I have that issue with my gNex and my wife's DNA on our home network. I don't think it is necessarily this phone, but I am not convinced (yet) that it is my router, either...
Click to expand...
Click to collapse
It comes and goes, it looks almost app specific. I say Hello Google Now, and it seems to lock up on recognition or says it can't connect to google....but I'm able to browse the internet.
Yeah I've been having a ton of WiFi issues with this phone.
Slusho said:
Yeah I've been having a ton of WiFi issues with this phone.
Click to expand...
Click to collapse
I called Moto and after dealing with their terrible level 1 support I got the following:
HERE ARE THE INSTRUCTIONS FOR DOING THE WIPE CACHE PARTITION:
This will remove any temporary files that may be causing the problem, but will not delete your files or settings.
1. With the phone powered off, press the VOL DOWN KEY for 2-3 seconds then POWER key then release.
2. The device will display different BOOT OPTIONS
3. Use the VOL DOWN Key to SCROLL to Recovery and VOL UP Key to select
Tip: If the device reboots, you may have waited to long to make a selection, you will need to begin the process again.
4. The device will display the Motorola logo and then the Android in distress ( logo with Exclamation mark)
5. Press and hold the VOL UP key for 10-15 seconds. While still holding the VOL UP key tap and release the POWER key
Tip: You can try this step, holding the phone in landscape. If you are stuck on step 6, try a force reboot by pressing the Power key and Vol Down key, and start the process again.
6. The device will display additional menu options (Text will appear in BLUE)
7. Use the VOL DOWN Key to scroll to wipe cache partition and the POWER Key to select this option
8. The device will then perform the partition wipe
9. The device will reboot and start the normal power up sequence
Ever since it hasn't had any problems, but it's only been a few hours as well.
The issues started happening again...turned off wifi and everything resynced perfectly...
ShamanicEnzan said:
The issues started happening again...turned off wifi and everything resynced perfectly...
Click to expand...
Click to collapse
Have you tried it on a different router?
Sent from my Nexus 7
phositadc said:
Have you tried it on a different router?
Sent from my Nexus 7
Click to expand...
Click to collapse
I haven't been able to yet, I'm hoping to at work, but my current router works with my laptop and my old HTC
ShamanicEnzan said:
I haven't been able to yet, I'm hoping to at work, but my current router works with my laptop and my old HTC
Click to expand...
Click to collapse
If it doesn't work properly with a different router try exchanging it. Also have you gone into advanced WiFi settings and forced the moto x to 2.4 GHz? If give that a try.
Sent from my Nexus 7
phositadc said:
If it doesn't work properly with a different router try exchanging it. Also have you gone into advanced WiFi settings and forced the moto x to 2.4 GHz? If give that a try.
Sent from my Nexus 7
Click to expand...
Click to collapse
It was set to auto, I set it to 2.4 ghz...now to wait if it happens again.
phositadc said:
If it doesn't work properly with a different router try exchanging it. Also have you gone into advanced WiFi settings and forced the moto x to 2.4 GHz? If give that a try.
Sent from my Nexus 7
Click to expand...
Click to collapse
The force to 2.4ghz actually made the problem occur a lot faster, any reason it might be due to the massive amount of wifi networks around? When I set to scan 5 ghz there was only one still open, I might go into my router and see if I can change the atenna settings.
EDIT: Turns out if I go to 5 ghz my computer can't connect, but I changed the channel to something less populated in the area to see if that helps.
DOUBLE EDIT: It appears to occur after I'm supposed to get a Facebook notification, at that point I don't get any more notifications....attempting to clear out facebook data and cache to see if that does anything
Try disabling WMM on your router.
drilus said:
Try disabling WMM on your router.
Click to expand...
Click to collapse
Forgive the stupid, but what's WMM short for in case that's not readily apparent?
Edit: I've also noticed the problem is exponentially worse after I upload pictures to facebook
Edit Edit: Found WMM, turned it off, let's see what happens.
I has this kind of issue before and did a cold boot but nothing happaned. so my last option was to do a restore. After that, my WIFI connection got okay again. problem solved :silly:
alicepattinson said:
I has this kind of issue before and did a cold boot but nothing happaned. so my last option was to do a restore. After that, my WIFI connection got okay again. problem solved :silly:
Click to expand...
Click to collapse
You mean full reset? It looks like I may have to do that with the idle battery drain issue anyways....so that's the last resort.
Hey guys I'm having a similar issue with my moto x on the 2.4ghz band. Speeds are very slow and sometimes cut out completely. Im getting a download speed of about 300kb/s on 2.4 both on auto channel and it doesn't rlly change once I change it manually to an open channel using WiFi analyzer app. My download speeds on 5ghz hit 4000kb/s even with a much lower signal strength.
YouTube and Netflix is unusable and growing the internet sucks. I usually just use the 4g network while at home cuz its a thousand times faster but I'd like this to be fixed regardless. Has anyone found a solution or explanation?
2.4 ghz wifi issues
matt87n said:
Hey guys I'm having a similar issue with my moto x on the 2.4ghz band. Speeds are very slow and sometimes cut out completely. Im getting a download speed of about 300kb/s on 2.4 both on auto channel and it doesn't rlly change once I change it manually to an open channel using WiFi analyzer app. My download speeds on 5ghz hit 4000kb/s even with a much lower signal strength.
YouTube and Netflix is unusable and growing the internet sucks. I usually just use the 4g network while at home cuz its a thousand times faster but I'd like this to be fixed regardless. Has anyone found a solution or explanation?
Click to expand...
Click to collapse
I'm having these issues too. Got the GSM Developer Edition on 11/29. It immediately updated to Kit Kat OTA so I'm not sure whether it had the issue prior to Kit Kat or not. This only happens on 2.4 ghz wifi and only with one of my routers at home, a Netgear WNDR3700v2 running OpenWrt Attitude Adjustment (I tried upgrading from Backfire to see if it would help, it did not). The other router is a Linksys WRT350N and when the phone is connected to that one the problem does not happen. Note, that there are 2 laptops, a Samsung Galaxy S2, and a Kindle Fire HDX that have zero problems with the WNDR3700. All can transfer data perfectly fine and at high speeds. Thus I do not think the router is bad. Have not checked work routers. 5 ghz wifi is totally fine and indeed very good with this phone.
For me, the problem is that the phone seems unable to receive data at high speed (over 1Mbps) on 2.4 ghz wifi in any area where the signal isn't perfect and sometimes even in the same room as the router (although usually it is fine there). Oddly in many cases when it has trouble receiving it can send data much faster. It almost seems like it might be some kind of interference as it is rather random.
At this point I'm wondering if the phone has a defective 2.4ghz subsystem, though that seem unlikely due to good transfer with the WRT350N, or if this is some kind of wifi tuning software bug in the phone.
Any info would be appreciated. Does anyone have this issue who did not have the issue on Jellybean? Am wondering if anything changed with wifi for the update? Note, I have tried clearing the cache in recovery as noted in another thread with no luck. Anyone have the WCNSS_qcom_cfg.ini file from Jellybean for this phone? Would rather not reflash just for 1 file.
Thanks.
glimmer00 said:
I'm having these issues too. Got the GSM Developer Edition on 11/29. It immediately updated to Kit Kat OTA so I'm not sure whether it had the issue prior to Kit Kat or not. This only happens on 2.4 ghz wifi and only with one of my routers at home, a Netgear WNDR3700v2 running OpenWrt Attitude Adjustment (I tried upgrading from Backfire to see if it would help, it did not). The other router is a Linksys WRT350N and when the phone is connected to that one the problem does not happen. Note, that there are 2 laptops, a Samsung Galaxy S2, and a Kindle Fire HDX that have zero problems with the WNDR3700. All can transfer data perfectly fine and at high speeds. Thus I do not think the router is bad. Have not checked work routers. 5 ghz wifi is totally fine and indeed very good with this phone.
For me, the problem is that the phone seems unable to receive data at high speed (over 1Mbps) on 2.4 ghz wifi in any area where the signal isn't perfect and sometimes even in the same room as the router (although usually it is fine there). Oddly in many cases when it has trouble receiving it can send data much faster. It almost seems like it might be some kind of interference as it is rather random.
At this point I'm wondering if the phone has a defective 2.4ghz subsystem, though that seem unlikely due to good transfer with the WRT350N, or if this is some kind of wifi tuning software bug in the phone.
Any info would be appreciated. Does anyone have this issue who did not have the issue on Jellybean? Am wondering if anything changed with wifi for the update? Note, I have tried clearing the cache in recovery as noted in another thread with no luck. Anyone have the WCNSS_qcom_cfg.ini file from Jellybean for this phone? Would rather not reflash just for 1 file.
Thanks.
Click to expand...
Click to collapse
For what it's worth I have this same Netgear router and have had the same connectivity issues on both 4.2.2 and 4.4.
I did some reading today and found a couple possible fixes I plan on trying out. First one is to disable WMM. Secondly I found on the official netgear forums that they have had major issues (some of which you've described) with all firmwares ending in the .30s and went so far as to pull them from their download section.
My router was running firmware .36 and I successfully downgraded it to the latest stable firmware .12 that netgear now recommends.
Hopefully 1 of those 2 fixes improves the performance, at any rate I really think it's something with the router itself and not the moto x.
Sent from my XT1060 using xda app-developers app
Thanks for letting me know this was also an issue on 4.2.2. Saves me the trouble of flashing back just to test.
I will be interested to know if your using official netgear 1.0.0.12 firmware fixes the issue for you. I haven't actually ever used the official firmware as I've run OpenWRT since I got the router a year or two ago. 10.03.1 had the issue, and it appears 12.09 does as well. I may try a trunk build at some point to see if that changes anything.
I had previously written that all was well on the 5 ghz band. This appears to not be 100% correct. Yesterday evening and this morning I found myself "connected" to the 5ghz band without actually having working internet. Toggle wifi on/off fixes it, but I shouldn't have to do it.
Not sure if this helps, but on the 2.4 ghz side things do work better on one side of the house vs the other. Also it seems that I can get a very fast connection at times and then it stumbles and gets stuck going under 1 Mbps. I still suspect either a defect or some kind of low level radio issues with the moto or the router regarding interference from neighboring wifi access points (there are a lot around me, single family houses on small lots). However, keep in mind no other device has these issues but the moto. In the rare instance I venture into a bad signal pocket the signal indicator goes down and speed slows or they lose connection vs the moto where it can show excellent signal and have no/nearly no connectivity.
I haven't tried it for long, but switching to wireless g mode vs ng may improve stability though I only briefly tried it. I did walk around part of my house checking the Mbps with the app "WiFi Speed Test" and while way slower than N mode it was far more stable. Even if this does work it is a definate downgrade in speed though.
Well its only been a day or two so it may be too early to tell, but so far my wifi seems much better after making those two fixes I mentioned above. This is on 2.4 band, the 5ghz band doesn't provide me enough signal strength to use all the time (router is too far from my bedroom).
The main issue I was having was my wifi signal would cut out even though it still showed a good connection. I could swipe down on the status bar and see no download arrow next to the wifi icon so I knew I wasn't receiving data. However a simple disconnect and reconnect to my wifi would fix the problem until it happened again. This seemed to be most common while watching YouTube videos, in fact it happened far too often which is why I went searching for a solution.
So as I mentioned things seem to be better for sure so far but I need to give it a week or so to see how much it is really helped, but so far I can't remember any wifi cutting out since I've made those two fixes.
Sent from my XT1060 using xda app-developers app

WiFi Issues

Hi Everyone
I looked and I could not find info on this issue. I have just used WiFi at home in the past with the Note 3 and it was fine. Here is some history of the changes:
- Old home WiFi was single band wireless N (53mbps) with a second repeater hot spot. This worked well with the Note 3.
- Had issues with the router so I upgraded to a dual band ac router and removed the second hot spot. So now it is just the new router for the whole house.
- Issues now - receive 2 bars at the far end of the house and basic WiFi is OK. Watching You Tube is an issue and it loads, plays for a few seconds, loads more etc.
I don't see a way to tell if I am on ac or wireless N. I was going to try to switch to wireless N and see if that helped but I can't see a way to do this? This router is way faster than my old one so I thought speed would not be an issue. no one else is using the wireless in the house. I would think that 2 bars would be strong enough? I think that wireless N would have a better range so that is why I wanted to try that. I am assuming that I am connecting to ac. Any thoughts?
thx in advance
AC routers have two separate ssid's. One for b,g,n. And another for 5G band. The 5G band default ssid is the same as the other with "5G" at the end. 5G band doesn't have good range, but it has faster speed between connected devices. 5G won't have faster internet unless you have a 100mb download speed. Which is unlikely. So your YouTube issue is either your modem, or a Qos setting in the router. If your router is at default settings it's definitely your modem.
You might be able to get more support on this subject thru a forum for your router, or modem.
scottwood2 said:
Hi Everyone
I looked and I could not find info on this issue. I have just used WiFi at home in the past with the Note 3 and it was fine. Here is some history of the changes:
- Old home WiFi was single band wireless N (53mbps) with a second repeater hot spot. This worked well with the Note 3.
- Had issues with the router so I upgraded to a dual band ac router and removed the second hot spot. So now it is just the new router for the whole house.
- Issues now - receive 2 bars at the far end of the house and basic WiFi is OK. Watching You Tube is an issue and it loads, plays for a few seconds, loads more etc.
I don't see a way to tell if I am on ac or wireless N. I was going to try to switch to wireless N and see if that helped but I can't see a way to do this? This router is way faster than my old one so I thought speed would not be an issue. no one else is using the wireless in the house. I would think that 2 bars would be strong enough? I think that wireless N would have a better range so that is why I wanted to try that. I am assuming that I am connecting to ac. Any thoughts?
thx in advance
Click to expand...
Click to collapse
why not use your old router from your old home as a repeater? wouldn't that work?
scottwood2 said:
- Issues now - receive 2 bars at the far end of the house and basic WiFi is OK. Watching You Tube is an issue and it loads, plays for a few seconds, loads more etc.
Click to expand...
Click to collapse
That's called buffering and it's due to low thruput (which is different than speed). It can be caused by low signal strength (due to distance or to the signal haveing to go through too much along the path), noise between the router and the phone, interference with someone else's wifi signal ...
You need at least a couple of apps like Signal Check Lite and Wifi Analytics to see what's going on. Guessing isn't going to give you a solution.

moto x pure att WIFI kills data signal

Issue: While connected to my EA6900 (1900 AC) linksys wireless modem my data dies. If I turn off wifi, I am able to call out, (although patchy), get texts, and use android services. As soon as I turn on wifi, these services all seem to shut down. Although sometimes some data is able to eak through.
Background: I am using a Moto x (2014) Pure Edition on the AT&T Network. I have confirmed time and time again that wireless works on my network, I have a full wifi signal and decent LTE signal (unsure how strong -- it shows 2-3 bars). I had this problem initially in 4.4.4 and it persists in 5.0 (I updated to see if that would fix the issue. Previously I had and HTC One with no issues what so ever. Reboots do not fix this issue and ATT has told me it is not their problem.
Hypothesis: I think the Moto X 2014 has problem connecting on the 5ghz (duel band) or AC networks. I have noticed while at work or other locations, I have had no connectivity issues with wifi on. I am pretty sure they are using standard 2.4ghz G and or N connections. I believe that the phone is unable to switch between the range of bands and causes it to lose data connectivity.
Has anyone had this issue or can anyone correct it?
I don't have an ac or 5ghz router so I can't test this. Have you played with the WiFi frequency band under advanced WiFi? You can force connect to 5ghz or 2.4ghz.
You could also turn off ac on the router configuration page to see if you can connect on n.
When I have time I will play around on my network to try and force the connection to different protocols. I have an AC router from EnGenius it's their ESR1200 which is a consumer grade device but pretty nice over all and was a steal at $60 over on Amazon:
http://www.engeniustech.com/home-networking/routers/16742-esr1200
But will try a few options. Right now I have it connected to the 5ghz band w/o issue. I can add I have long encountered issues for Android when moving between wifi networks. It has always been prone to struggling to juggle connections, even when switching nodes on a mono-SSID network. I can trace my issues back to Jelly Bean. But it seems like you are seeing something different.
If I find anything I'll post it soon as time permits, busy week for me at work or I might get lucky and just die in my sleep.
EDIT: For giggles I forced a connection to the 5ghz side and sent some texts as well as a couple calls w/o issue. Was able to receive as well. Mode is .11n of course and a solid 433mbps network connection speed
This is where my hypothesis really dies... I have attempted forcing 2.4 or 5ghz but both failed. The other option is the phone doesnt play nice with the EA6900... which is seemingly supported by the fact that my phone hasnt had any issues while i am connected to my parents house for thankgsiving. They are running 2.4ghz at a blazing 65mbps (i usually average around 400 at my house on my ea6900). Could it be the AC modem? One other thought is chromecast is somehow interfering with my phone. I will need to try removing chromecast when i get home to see if that works, but at this point, i would find it hard to imagine.
This is literally driving me up a wall.
EDIT: So I am at home at it has been running better but just now it has decided to seize up. Showing same info... 2.4ghz 65mpbs same network... full bars.... att shows 3/5 bars but doesnt say LTE or H or anything..just ATT (pretty sure thats normal)
http://www.amazon.com/gp/aw/cr/B00EXK14S0/s=sd/ref=mw_dp_cr
There are a bunch of comments about it overheating and dropping signal repeatedly. I would think about returning it under warranty.
kcustom11 said:
http://www.amazon.com/gp/aw/cr/B00EXK14S0/s=sd/ref=mw_dp_cr
There are a bunch of comments about it overheating and dropping signal repeatedly. I would think about returning it under warranty.
Click to expand...
Click to collapse
I owned this router and had problems with android devices staying connected.
Sent from my Nexus 6 using Tapatalk
kcustom11 said:
http://www.amazon.com/gp/aw/cr/B00EXK14S0/s=sd/ref=mw_dp_cr
There are a bunch of comments about it overheating and dropping signal repeatedly. I would think about returning it under warranty.
Click to expand...
Click to collapse
I wanted to blame my router very badly... however i have never experienced any drops on my laptop -- unless my laptop somehow deals with drops better than my phone...

Wifi blows on 10.5

I gotta tell ya, id absolutely love this thing if it wasnt for wifi issues. This thing drops connection all the time and lags so bad its awful. Done everything I read to do, freezing or deleting apks. Think it would be a home run if it wasnt for the wifi.
I've had mine a few weeks and I've never seen it drop wifi.
Sent from my SM-T800 using XDA Free mobile app
Never had a problem with the wifi, but the lag is horrible
Did you messes with your kernel?
I've got an 8.4 but I'm assuming the WiFi hardware is the same??? I've had mine for several months and never dropped a connection (except when my router went down) . I use it mainly on a 2.4 Ghz network at work. In my office I'm on the other side of an elevator shaft from the access point so reception isn't good on any device in my particular location - but it works and even there never dropped a connection. At home I've got it on 5 Ghz and where I typically use it the signal is very strong. On speedtest.net it matches the speed of my desktop PC which is wired into the router....so it's getting all my internet connection has to offer (service level is 30 Mbps but speedtest.net usually shows 32 - 35).
I'm assuming you have already checked the obvious things like signal strength? Does it drop the connection in some locations but not others? Does it make a difference what router or access point you are connecting to? Interference from other WiFi networks or (if using 2.4 Ghz) other devices like cordless phones?
Try installing WiFi Analyzer (free in the play store). It will give you a real time chart of your signals strength for all access points it can detect on both 2.4 Ghz and 5 Ghz. For example in my Culdesac I can see at least 6 other access points with pretty strong signals (all my immediate neighbors). At my office, on the side of the building facing an appartment building on the opposite side of the street, I can see at least 25 2.4 Ghz access points. Amazing how many are named Xfinity WiFi or Linksys . On the other hand, on the 5 Ghz band in my home I only see one access point other than mine.
Try manually setting your router/Access point to a channel no one else is using. Switch to 5 Ghz if your router has it or buy a new router if it doesn't. This band is a lot less crowded, at least where I live. If your signal strength is low in the place you want to use the tablet, try moving closer to the router to see if that helps. If it does, consider moving the router or getting a second router or repeater.
I use to have problems in my home with 2 things.
A baby room monitor - REALLY tore up my wifi all over the house!
A set of wireless rear surround speakers was a problem for about a day. Lucky for me they have the ability to change the channel they use. Wipped out my freq counter, found out where they were and moved them to ch 11. Unit isn't marked as to what 3 channels you can select from. So the freq counter helped me find where they were and where I could put them. After I got them on ch11 I moved the router to ch4 as there was no one using it near by. Problem solved and have no wifi problems at all with the Sammy.... Matter of fact my router sits on a cabinet 6 feet off the floor. I get coverage over my whole .7 acre Ponderosa while listening to music riding the mower!
my wifi seems to drop once in a while too but i think its the crap router i use.. not sure
i also reset my tab and that helped.
Another thing I just thought of that you may want to check.....
Make sure no devices are fighting with each other trying to get the same address on your network. I just went through this last night. Once resolved, no problem.
flhthemi said:
I use to have problems in my home with 2 things.
A baby room monitor - REALLY tore up my wifi all over the house!
A set of wireless rear surround speakers was a problem for about a day. Lucky for me they have the ability to change the channel they use. Wipped out my freq counter, found out where they were and moved them to ch 11. Unit isn't marked as to what 3 channels you can select from. So the freq counter helped me find where they were and where I could put them. After I got them on ch11 I moved the router to ch4 as there was no one using it near by. Problem solved and have no wifi problems at all with the Sammy.... Matter of fact my router sits on a cabinet 6 feet off the floor. I get coverage over my whole .7 acre Ponderosa while listening to music riding the mower!
Click to expand...
Click to collapse
A lot of this sort of problem can be fixed by going to 5 Ghz - which may mean a new router if you are using a router that isn't dual band. Most of those other devices in homes (and in your neighbor's homes too) are on 2.4 Ghz so there are a lot of things that compete for that spectrum that aren't even WiFi.
No WiFi issues here
No wifi issues here. I was on stock for about the 1st 30 days on the device and have rooted and installed various ROMs since. I would argue that this device has better wifi than other devices in my house, though my router is not AC so I have no comment on AC performance. I do have an issue with N 5 ghz networks not being seen right now, but that is something I induced.
Too many factors to consider but I can say if other's haven't had issues than it's likely something else.
Distance from access point
Access point's distance from other electronic equip.,
Wireless channel
G or N connection
latest firmware on wireless access point
cabling on AP
trying a different Access Point or wireless network altogether (coffee shop, etc)
wireless sucks to troubleshoot. Constantly changing settings until some magical combination works for all of your equipment.
like to connect my Nexus 5 to wireless N I have to set my 5Ghz channel to be on upper or lower frequency band or something- can't remember which it's supposed to be, though. My PSP needs the 2.4Ghz radio set on a b/g mixed setting. That's the only weird wireless settings I've ever needed to actually get specific devices to connect.
if you're looking for advice we'd need to know the model of your router/access point, though I'd probably go look at a forum where people talk about it.
Hi,
I am wondering, if anyone else having this problem...
My best available 2.4 ghz wifi channel is 13 (2472). If I select this channel my tab does not find the wifi anymore ("out of range"). All my other devices are running on channel 13. All other channels working.
Tried it with stock rom + stock kernel as well as with stock rom + latest UpInTheAir kernel, iron rom + UpInTheAir kernel, iron rom + stock kernel, factory reset, clean flash etc...
Can anyone confirm channel 13 is working on this tab?
SM-T805
Thx, brgds!

Categories

Resources