Razi XT890 Flash failed? - RAZR i Q&A, Help & Troubleshooting

I finally got RSD to accept my phone and file and during process 7 it failed.
Now all I get is a Red Moto Logo?
What can I do?

Same problem here, cant access fastboot or any other recovery. equal which combination of power and vol up or down. anyone got an solution?

PlusOne3k said:
Same problem here, cant access fastboot or any other recovery. equal which combination of power and vol up or down. anyone got an solution?
Click to expand...
Click to collapse
Somehow I made my phone Boot by taking out SD card.
Try it, it boots mine ok and I may give up Updating to KK until someone replies.

Yes, that worked for me. Thanks.
Gesendet von meinem A0001 mit Tapatalk

Related

Aborted updates, bootloop

Xperia z
I got a unit that should be revived because unfortunately the link was interrupted update.
If the charger plugged in., 3 and quiver just keep bootloop
The image does not appear ..
I can not enter into Recovery ...
What can be done?
Try to flash with Sony Update Service or with flashtool.
Gesendet von meinem C6603 mit Tapatalk
---------- Post added at 01:33 PM ---------- Previous post was at 01:32 PM ----------
If you use SUS your data will be gone but I thinks that isnt the biggest problem right now ^^
Gesendet von meinem C6603 mit Tapatalk
gripfly said:
Try to flash with Sony Update Service or with flashtool.
Gesendet von meinem C6603 mit Tapatalk
---------- Post added at 01:33 PM ---------- Previous post was at 01:32 PM ----------
If you use SUS your data will be gone but I thinks that isnt the biggest problem right now ^^
Gesendet von meinem C6603 mit Tapatalk
Click to expand...
Click to collapse
The problem is that the phone is completely discharged and I can not turn it off!
If I connect to a data cable, straight starts, and copper 3, then reboot ...
Continuous loops only!
Aha ok, yeah that is a really bad situation. ^^
now only I dont understand what you mean with the copper?
You mean that yiu tryed it with dockingstation or what?
Gesendet von meinem C6603 mit Tapatalk
gripfly said:
Aha ok, yeah that is a really bad situation. ^^
now only I dont understand what you mean with the copper?
You mean that yiu tryed it with dockingstation or what?
Gesendet von meinem C6603 mit Tapatalk
Click to expand...
Click to collapse
AA is not copper!
I'm sorry ..
3 vibrates and start again!
and no picture, I can not reach the bootloader and not recovery!
any combination not respond!
szunyi77 said:
AA is not copper!
I'm sorry ..
3 vibrates and start again!
and no picture, I can not reach the bootloader and not recovery!
any combination not respond!
Click to expand...
Click to collapse
enter flashmode and flash stock rom? will lost root and mods but not your data
Jambu95 said:
enter flashmode and flash stock rom? will lost root and mods but not your data
Click to expand...
Click to collapse
I do not know unfortunately.
I do not know how to rom it may be
I have not messed up, I do not know what they did to him!
szunyi77 said:
I do not know unfortunately.
I do not know how to rom it may be
I have not messed up, I do not know what they did to him!
Click to expand...
Click to collapse
What? To rom it? What does it mean?
If you hold volume up and power during the boot, up to the 3 vibrates and then shutting off the phone. After you plug in the charger it will charge or always the same?
Gesendet von meinem C6603 mit Tapatalk
if you do not plug into the charger, the device does not boot!
If you connect a charger or data cable then vibrates 3​​, the red LED will flash and start again!
Unfortunately, I can not do anything with it!
the solution would be to spend so?
And flash mode? Volume down holding during plug in the cable to the pc. For the flashmode it doesnt have to boot i think
Gesendet von meinem C6603 mit Tapatalk
---------- Post added at 04:52 PM ---------- Previous post was at 04:51 PM ----------
And using newest flashtool
Gesendet von meinem C6603 mit Tapatalk
When you join data cable and SUS, the following occurs:
We recognize the device and discarded ... We recognize the device and discarded ... This loop is now!
szunyi77 said:
When you join data cable and SUS, the following occurs:
We recognize the device and discarded ... We recognize the device and discarded ... This loop is now!
Click to expand...
Click to collapse
And If you use flashtool installing a stock firmware?
gripfly said:
And If you use flashtool installing a stock firmware?
Click to expand...
Click to collapse
I can not install on anything!
Constant loop!
I join as a cable, then the red light flashes, the phone vibrates 3​​, and re-re!
szunyi77 said:
I can not install on anything!
Constant loop!
I join as a cable, then the red light flashes, the phone vibrates 3​​, and re-re!
Click to expand...
Click to collapse
shut down the phone.
connect the cable to the XZ
opening flashtool and choose flashmode
choose FW
check wipe all data
click flash
waiting for flashtool which is during preparing for flash
if it ask fo phone volume down hold+ plug cable to pc
Click to expand...
Click to collapse
yeah but you din't it like this right?
me remembered I had the same with red light and vibrate..^^
I remember for something wait I will look for It! I hope I will find it..
If this I wrote before editing will not work try this:
http://forum.xda-developers.com/showthread.php?t=2229250&highlight=recovery
gripfly said:
yeah but you din't it like this right?
me remembered I had the same with red light and vibrate..^^
I remember for something wait I will look for It! I hope I will find it..
Is below the Sony logo!
no picture no!
only red light, vibration, and 3 ...
When you join, and I'm trying to install SUS, it is connected to drop ... connected to drop ...
I tried windows 7 and 8-8.1
If this I wrote before editing will not work try this:
http://forum.xda-developers.com/showthread.php?t=2229250&highlight=recovery
Click to expand...
Click to collapse
Thank you!
Any combination I use, I left the red light and vibration 3!
alas!
I tried to sus, but once detected, drop, drop-detect ...
I hope you understand ...
Is below the Sony logo!
no picture no!
only red light, vibration, and 3 ...
When you join, and I'm trying to install SUS, it is connected to drop ... connected to drop ...
I tried windows 7 and 8-8.1
FASTBOOT MODE: soft-brick
FASTBOOT FOR KERNEL
Connect your USB cable to your phone
Either:
Hold POWER and VOL-UP to reboot, on the instance your phone vibrates, release POWER but hold on to VOL-UP;
Press POWER, on the instance you feel your phone vibrate, press and hold VOL-UP;
If successful your phone will show a blue led to signal it is in fastboot mode.
Use the fastboot tool to flash the stock Sony kernel image.
Your phone should boot up normally again when fastboot is done.
CONSIDER YOURSELF LUCKY YOU CAN STILL USE YOUR PHONE IF YOU LOSE ANY DATA!!
Click to expand...
Click to collapse
So this you tried too and still the same?
Fu..k.. I hope we can get you Z to live again..
gripfly said:
So this you tried too and still the same?
Fu..k.. I hope we can get you Z to live again..
Click to expand...
Click to collapse
I've tried everything so far ... : (
Unfortunately, I do not want to come to life!
as cord, immediately start the loop ...
the red LED will flash and quiver 3
If there is no connection, then there is no light!
There is no blue LED!
only flashes of red!
If you join SUS, you know, you do not know, he knows, does not recognize the device!
What could it be?
What are you trying?
, (
szunyi77 said:
I've tried everything so far ... : (
Unfortunately, I do not want to come to life!
as cord, immediately start the loop ...
the red LED will flash and quiver 3
If there is no connection, then there is no light!
There is no blue LED!
only flashes of red!
If you join SUS, you know, you do not know, he knows, does not recognize the device!
What could it be?
What are you trying?
, (
Click to expand...
Click to collapse
Can you do a picture or better a short video like it looks? maybe it's helpfully, i don't know but I hope..
gripfly said:
Can you do a picture or better a short video like it looks? maybe it's helpfully, i don't know but I hope..
Click to expand...
Click to collapse
I tried, it's hard for me alone to do the video ...
I wonder what, exactly?
Which event?
we are able to advise?
Yeah what you tried yet. It dosent have to be a professional video
Show what happen you want start the phone, when you plug in the current supply, when you try to flash with pcc sus and flashtool.
Gesendet von meinem C6603 mit Tapatalk
---------- Post added at 10:49 PM ---------- Previous post was at 10:48 PM ----------
That I/we see what you do and whats happening. Maybe if we see whats happening, we a better chance i hope
Gesendet von meinem C6603 mit Tapatalk

[Q] Bootloop after trying to flash a CM

So basically I've tried to flash CM but I didn't flash the CM recovery, now Im getting bootloops and I can't either start flashmode or flashtool.
Can anyone help?
tehiaz said:
So basically I've tried to flash CM but I didn't flash the CM recovery, now Im getting bootloops and I can't either start flashmode or flashtool.
Can anyone help?
Click to expand...
Click to collapse
I don't understand, what did you did?
Are you sure you can't access in flashmode?
Plug the usb cable in and press vol -
tehiaz said:
now Im getting bootloops and I can't either start flashmode or flashtool.
Click to expand...
Click to collapse
Flashtool you can start, because it's a programm for example windows.. anyway
Just a information for you: Always tell what exactly your problem is AND what you did or what happened. Because we do not know if you, for example, unlocked your bootloader or what you did wrong because we do not know what you have done. So tell us what you did step by step. Because if you learn what you did wrong, you will maybe not do the same failure again
Start flashtool and connect your phone in fastboot. what happens?
gripfly said:
Flashtool you can start, because it's a programm for example windows.. anyway
Just a information for you: Always tell what exactly your problem is AND what you did or what happened. Because we do not know if you, for example, unlocked your bootloader or what you did wrong because we do not know what you have done. So tell us what you did step by step. Because if you learn what you did wrong, you will maybe not do the same failure again
Start flashtool and connect your phone in fastboot. what happens?
Click to expand...
Click to collapse
So okay.. At start I unlocked bootloader, then I went to the recovery and flashed Cyanogen (then I got some error, i believe it said error=7) then I restarted recovery (and it didn't went to the recovery (it kinda skipped it), and I started getting bootloops, I connected the phone to computer, I entered flashmode or fastboot (can't remember which one), then I panicked, and hard-resetted the device (that was dumb as ****, i think that's the problem), and now i can turn it on (it keeps bootlooping though) but I can't enter either flashmode or fastboot and computer doesn't recognise the phone, it doesn't even see it.
I think the 2 mistakes I did was not flashing the new ClockworkMod (I flashed it in old) and then hardresetting while in flashmode or fastboot, but now I have no idea what shall I do...
Sry for not giving full information, ty for trying to help guys.
"Device disconnected" and literally nothing more after that. No matter whatever I do. I can't either enter flashmode or fastboot. Nothing. I can just turn on the phone and watch it bootlooping.
bump
is there someone who can help me? i'll be eternally grateful if someone will manage to help me fix this.
tehiaz said:
bump
is there someone who can help me? i'll be eternally grateful if someone will manage to help me fix this.
Click to expand...
Click to collapse
And you can't use recovery?
Maybe it helps if you reinstall the drivers to connect in fastboot or flashmode..
gripfly said:
And you can't use recovery?
Maybe it helps if you reinstall the drivers to connect in fastboot or flashmode..
Click to expand...
Click to collapse
Sadly I can't use it, I don't think it may help cause I don't see a green or blue led so I think it's up to phone not computer.
tehiaz said:
Sadly I can't use it, I don't think it may help cause I don't see a green or blue led so I think it's up to phone not computer.
Click to expand...
Click to collapse
Okay, so I've got update. I've tried going to flashmode/fastboot after discharging the battery and led flashes 3 times (red color).
Is that good, or not?
tehiaz said:
Okay, so I've got update. I've tried going to flashmode/fastboot after discharging the battery and led flashes 3 times (red color).
Is that good, or not?
Click to expand...
Click to collapse
Charge it now. I think the flashes shows the the battery is discharged.
gripfly said:
Charge it now. I think the flashes shows the the battery is discharged.
Click to expand...
Click to collapse
I'll get up earlier next morning and I'll try to flash kernel (can I get to recovery by flashing a stock kernel? can I flash a stock kernel now? should I flash it with flashmode or fastboot?) I have recovered fully my phone in CWM before flashing Cyanogen so I can recover this.
I think it's good that phone reacts to trying to get in flashmode. It may be a good signal.
Again thanks for help Sir.
Edit:
Btw not sure if it changes osmething but I have no red when I am charging and now I can't even start the phone. (3 red led blink)
tehiaz said:
I'll get up earlier next morning and I'll try to flash kernel (can I get to recovery by flashing a stock kernel? can I flash a stock kernel now? should I flash it with flashmode or fastboot?) I have recovered fully my phone in CWM before flashing Cyanogen so I can recover this.
I think it's good that phone reacts to trying to get in flashmode. It may be a good signal.
Again thanks for help Sir.
Edit:
Btw not sure if it changes osmething but I have no red when I am charging and now I can't even start the phone. (3 red led blink)
Click to expand...
Click to collapse
bump
tehiaz said:
I'll get up earlier next morning and I'll try to flash kernel (can I get to recovery by flashing a stock kernel? can I flash a stock kernel now? should I flash it with flashmode or fastboot?) I have recovered fully my phone in CWM before flashing Cyanogen so I can recover this.
I think it's good that phone reacts to trying to get in flashmode. It may be a good signal.
Again thanks for help Sir.
Edit:
Btw not sure if it changes osmething but I have no red when I am charging and now I can't even start the phone. (3 red led blink)
Click to expand...
Click to collapse
What now? Does you can connect your phone in fastboot or flashmode?
Gesendet von meinem C6603 mit Tapatalk
gripfly said:
What now? Does you can connect your phone in fastboot or flashmode?
Gesendet von meinem C6603 mit Tapatalk
Click to expand...
Click to collapse
No.. I can't even turn it on cause of led blinking 3 times. And I can't start the flashmode as well.
tehiaz said:
No.. I can't even turn it on cause of led blinking 3 times. And I can't start the flashmode as well.
Click to expand...
Click to collapse
Hold Volume up and power. What happens?
gripfly said:
Hold Volume up and power. What happens?
Nothing. Volume + power up is a shortcut for phone which is turned on. My phone is turned off.
Click to expand...
Click to collapse
What happens if you try to turn your phone on while it is connected with the charger?
Gesendet von meinem C6603 mit Tapatalk
gripfly said:
What happens if you try to turn your phone on while it is connected with the charger?
Gesendet von meinem C6603 mit Tapatalk
Click to expand...
Click to collapse
Led flashes 3 times (red).
tehiaz said:
Led flashes 3 times (red).
Click to expand...
Click to collapse
I have no ideas more.
Maybe something of your hardware is damaged. I really don't know, nothing works like you said. That is the reason why I would say it's something with the hardware..
Gesendet von meinem C6603 mit Tapatalk
gripfly said:
I have no ideas more.
Maybe something of your hardware is damaged. I really don't know, nothing works like you said. That is the reason why I would say it's something with the hardware..
Gesendet von meinem C6603 mit Tapatalk
Click to expand...
Click to collapse
I think it's due to hard-resetting while in bootloop. http://forum.xda-developers.com/showthread.php?t=1849170 I've read entire thread and I think the phone needs still a bit time to discharge... But i think 120 hours should be enough to discharge a 80% phone with screen mostly turned off.
Anyways thank you very much for helping and if you'll come with more ideas i'd be grateful.
Have a great day.

[Q][C6602] Kind of a bootloop

Good evening everyone,
I'm having an issue with my C6602 lately, I updated it to latest firmware through OTA, a day later, it just wouldn't boot up and got really hot.
I tried flashing another firmware with flashtools, succeded, but then, whenever I turn it on, I have 5 seconds max, and it reboots (unless I turn the screen off, this way it'll work, but will eventually reboot if I turn on the screen.)
I looked in the forums, and tried most of the solutions, I even reset it using sony companion.
Now I'm stuck with kind of a brick, the phone doesn't turn on, but if I plug it to a wall, it boots up, but gets stuck on lock screen (irresponsive), reboots after a while, gets stuck, reboots, then gets stuck for as long as I keep it plugged in, then turns off as soon as I unplug it and starts bootlooping until battery dies.
Anybody got any idea ? Please do ask if you need any more details.
Thanks in advance.
Before you updated you was also on stock ROM?
So flashtool recognize your phone without problems?
Gesendet von meinem C6603 mit Tapatalk
gripfly said:
Before you updated you was also on stock ROM?
So flashtool recognize your phone without problems?
Gesendet von meinem C6603 mit Tapatalk
Click to expand...
Click to collapse
Yes, phone is recognized by flashtool, now the issue is as follow (edited the first post too).
Phone doesn't turn on, but if I plug it to a wall, it boots up, but gets stuck on lock screen (irresponsive), reboots after a while, gets stuck, reboots, then gets stuck for as long as I keep it plugged in, then turns off as soon as I unplug it and starts bootlooping until battery dies.
Before you updated you was also on stock ROM?
Click to expand...
Click to collapse
Try to repair with Sony Update Service(SUS).
gripfly said:
Try to repair with Sony Update Service(SUS).
Click to expand...
Click to collapse
If I remember well, the phone must reach 50% battery to be repaired with SUS, but this just wouldn't happen, when the phone gets stuck on lock screen, it gets really hot, and even if I let it sit there for an hour, the battery percentage won't change much. I'll try it again anyway, there is no other method than SUS ?
Edit: It says I have the latest version installed
Huntex said:
I'll try it again anyway, there is no other method than SUS ?
Edit: It says I have the latest version installed
Click to expand...
Click to collapse
Since you get your phone recognized by SUS make sure battery is more than 50% charged and try the repair option.
SUS and flashtool is your friend i guess..
akisg said:
Since you get your phone recognized by SUS make sure battery is more than 50% charged and try the repair option.
SUS and flashtool is your friend i guess..
Click to expand...
Click to collapse
Repair option, hum, I just tried the update thing.
I'll try to leave it plugged for night (and hope it won't blow up), and then try to repair tomorrow.
I'll let you know either way.
Thanks
Huntex said:
If I remember well, the phone must reach 50% battery to be repaired with SUS, but this just wouldn't happen, when the phone gets stuck on lock screen, it gets really hot, and even if I let it sit there for an hour, the battery percentage won't change much. I'll try it again anyway, there is no other method than SUS ?
Edit: It says I have the latest version installed
Click to expand...
Click to collapse
And if it stucks on lock screen, does it turn off if you hold power and volume up(12 seconds i thought you have to hold the combination, it have to vibrate 3 times)?
gripfly said:
And if it stucks on lock screen, does it turn off if you hold power and volume up(12 seconds i thought you have to hold the combination, it have to vibrate 3 times)?
Click to expand...
Click to collapse
Yes it does, then it reboots, then gets stuck again (Sometimes it even gets stuck while there's the wave animation after the xperia logo).
Huntex said:
Yes it does, then it reboots, then gets stuck again (Sometimes it even gets stuck while there's the wave animation after the xperia logo).
Click to expand...
Click to collapse
just download an ftf and flash it via flashtool
open flashtool and connect your phone via usb cable while pressing the volume down button to enter flashmode
Rzr92 said:
just download an ftf and flash it via flashtool
open flashtool and connect your phone via usb cable while pressing the volume down button to enter flashmode
Click to expand...
Click to collapse
As I mentioned before, flashing an ftf didn't fix the bootloops, nor the freezing
Huntex said:
As I mentioned before, flashing an ftf didn't fix the bootloops, nor the freezing
Click to expand...
Click to collapse
If you flashed correctly with flashtool and SUS doesn't help also, I would say there is a hardware problem. Because more or less you can solve every software problem with your phone with a clear flash.
You don't have a recovery, right?
Gesendet von meinem C6603 mit Tapatalk
gripfly said:
If you flashed correctly with flashtool and SUS doesn't help also, I would say there is a hardware problem. Because more or less you can solve every software problem with your phone with a clear flash.
You don't have a recovery, right?
Gesendet von meinem C6603 mit Tapatalk
Click to expand...
Click to collapse
No recovery, no.
Im unrooted, and bootloader is locked, guess I'll have to take it back from where I bought it for a fix, it looks like a hardware problem (leaving the phone plugged for the night didn't change a thing)
Your battery has a problem, anyone would say. Try a fresh FTF install with wiping data. Also try repair. For that you need to charge your phone when it is turned off. And make sure FTF version is newer or at least same with your latest firmware worked fine.

[Q] S4 active stuck in "samsung galaxy s4 active i9295" screen

Help! I am still a newbie here.
So, I was excited to manually flash the official kitkat firmware for i9295, so i downloaded it from the internet.
But i couldn't explain what happened. Formerly, my phone was running a Carbon Rom "CARBON-KK-UNOFFICIAL-20140514-0523-jactiveltexx",
with clockworkmod recovry 6.0.3.5 (i think).
while waiting for the Official Kitkat Rom to finish downloading, i went and went to CWM recovery and wipe data, factory reset, and dthings like that etc. and starting the phone again.
Until It got stuck in the start screen of the phone which shows " Samsung Galaxy S4 Active i9295"
Please Help! I have been searching everywhere but there is no such solution to be found.
Please help! Even when i charge my phone, there is no animation, it just shows the battery with the circle and it freezes!
I will post pictures when i get a capturing device, please help me if you know a solution
Just start your phone in download mode (volume down + home + power) and install kitkat with odin
Gesendet von meinem GT-I9295 mit Tapatalk
I already did it
4cr0ph3t said:
Just start your phone in download mode (volume down + home + power) and install kitkat with odin
Gesendet von meinem GT-I9295 mit Tapatalk
Click to expand...
Click to collapse
I tried to flash back the official stock firmware 4.2.2 but odin kept saying "no Pit partition" or something like that,
Then I include the Pit file for i9295 but it kept saying "FAIL, Re partition failed" or something like that

PRA-LX1 bricked

Hi all.Last night i tried to root my pra-lx1 and bricked my phone.I tried install custom rom, dload method etc.For now its only have bootloop.I dont want to pay untrustable phone stores for this and huawei service said they need to change motherboard for fix and it costs 300$.
Bootloader unlocked
frp locked
got erecovery but it stucks at %99 when trying to factory reset.However i made factory reset but device still on bootloop.
my firmware model : PRA-LX1C432B103
cloudbrow said:
Hi all.Last night i tried to root my pra-lx1 and bricked my phone.I tried install custom rom, dload method etc.For now its only have bootloop.I dont want to pay untrustable phone stores for this and huawei service said they need to change motherboard for fix and it costs 300$.
Bootloader unlocked
frp locked
got erecovery but it stucks at %99 when trying to factory reset.However i made factory reset but device still on bootloop.
my firmware model : PRA-LX1C432B103
Click to expand...
Click to collapse
Use the DC PHOENIX TOOL too unbrick your phone...it is a paid software 15 Euros for 72 hours
Sent from my PRA-LA1 using Tapatalk
hamzio7 said:
Use the DC PHOENIX TOOL too unbrick your phone...it is a paid software 15 Euros for 72 hours
Sent from my PRA-LA1 using Tapatalk
Click to expand...
Click to collapse
I cant use my credit cards internet buying option...... Cant buy anything without 3d secure.
cloudbrow said:
I cant use my credit cards internet buying option...... Cant buy anything without 3d secure.
Click to expand...
Click to collapse
https://mega.nz/#!VcB21ZpZ!0gmdSY9eRINZ08mLQGunXZOz6CuKM1SS_7rt6mjRAXY
Try this dload package...it was reported to work...but first you have to flash the stock recovery...
Sent from my PRA-LA1 using Tapatalk
@hamzio7
Thanks mate i will try this. I flashed stock recovery and when im pressing volume + and power button i can enter emui recovery which have factory data setting; when pressing volume - and power button im entering another emui recovery which doesnt have factory data setting. Is something wrong?
cloudbrow said:
@hamzio7
Thanks mate i will try this. I flashed stock recovery and when im pressing volume + and power button i can enter emui recovery which have factory data setting; when pressing volume - and power button im entering another emui recovery which doesnt have factory data setting. Is something wrong?
Click to expand...
Click to collapse
@hamzio7 another question, if update.app doesnt work (stucks at %5 always you know) can i try to extract important img files and flash them with fastboot?
cloudbrow said:
@hamzio7
Thanks mate i will try this. I flashed stock recovery and when im pressing volume + and power button i can enter emui recovery which have factory data setting; when pressing volume - and power button im entering another emui recovery which doesnt have factory data setting. Is something wrong?
Click to expand...
Click to collapse
There are two different partitions for recovery...the default one and the eRecovery ...so it's normal
Sent from my PRA-LA1 using Tapatalk
hamzio7 said:
There are two different partitions for recovery...the default one and the eRecovery ...so it's normal
Sent from my PRA-LA1 using Tapatalk
Click to expand...
Click to collapse
I tried link you posted and it isnt worked
cloudbrow said:
I tried link you posted and it isnt worked
Click to expand...
Click to collapse
What did you do?
Sent from my PRA-LA1 using Tapatalk
hamzio7 said:
What did you do?
Sent from my PRA-LA1 using Tapatalk
Click to expand...
Click to collapse
2 minutes ago i made update with update.app from your link. Now i got huawei logo always on and doesnt starting. And now there is no ''your bootloader unlocked phone cannot truste bla bla'' message when opening. I cant shutdown phone it always trying to boot.
It may take awhile to boot up...do a factory reset if you are not sure
Sent from my PRA-LA1 using Tapatalk
Did it work?
Have you fixed your phone?
Sent from my PRA-LA1 using Tapatalk

Categories

Resources