Related
I will soon be opening up my phone (T-mobile Pocket PC Phone Edition) to replace the glass screen with a new one ordered online. I've never even opened the phone before and was wondering if someone has performed this operation before. I would really appreciate any pointers, tricks, cautions, pictures, etc.
Thanks.
lawrence... where did u get the replacement??
i wonder if they got replacement cases! i chiped mine
The company I bought the screen from was GetHighTech, Inc, in California. By coincidence, they are about an hour's drive away from my home.
They only sell the glass screen and high capacity battery replacements. The screen comes with absolutely no documentation or instructions. I just got it a few minutes ago.
just wanted to see if you had any luck with the changeout.
Screen replaced successfully: observations
It was a tricky operation, but I finally managed to replace my broken touch screen. And the patient is alive, and only a little worse off for the experience.
I was held back for a week until I could get the right size torx screwdrivers to remove the back cover. Once inside, it was a very very tricky process slicing off the broken screen with a razor blade. It was glued to the lcd display. This would have been hard even if the screen was not shattered. Definitely needed goggles to protect against flying splinters of glass. I used cotton swabs and 99% alcohol to clean the glass dust off the glue around the edges of the lcd, then I put the new screen on while that residual gum was still a bit tacky.
There was a very thin existing plastic cover over the lcd in between the glass touch screen and the rest of the lcd. Since it did not come off with the glass, I left it in place even though it had a couple of small scratches from contact with the broken glass. It seems like it was there to keep dust off the lcd or something like that.
This was my first time inside the phone. I noticed that replacing the whole LCD component would have been a trivial task by comparision to replacing the glass alone. And even easier would have been adding a new battery.
cracked lcd on xda
hi, does anybody know where i can get a replacement for the lcd screen on my xda... its totally mashed and i need to unlock it but the screen is bad...
i live in uk... any ideas guys..
pls help out
has anyone give me pls an idea how much a new replacement screen for XDA might cost
currently I am having two XDA (one XDA and one MDA), MDA has a broken screen ... I'd like to know how much is the material (screen), I have so. to do the actual job of screen replacement
regards, monika
I replaced my touchscreen a few weeks ago. Like Lawrence said it's a little tricky and you need to be patient.
I bought my touchscreen from www.pdasmart.com/pdaphone.htm for $75 and they gave great instructions.
thank you for your kind answer
hmmm, seems like it is nice to live in US ... where all the things for XDA are almost readily available :wink:
regards, monika
Protective Acryclic Cover over the Digitizer
I have an odd problem. I have an SX56 with a broken protective cover. The protective cover is the acrylic sheet that sits between the digitizer and the outside world. Everything else works fine including the digitizer. I have found every replacement part except that cover. I've even tried local plastic stores. They don't carry the proper thickness (0.125mm).
Any thoughts or sources besides sending it in for a $200 repair?
This question is directed to those who have taken apart their Kaiser, and specifically screen the screen assembly. I've got water issues and the screen is broke now. Here's the story. I might get some outrageous warranty charges.
I installed the InvisiShield (www.shieldzone.com) on my phone. Essentially it's a screen protector that is indestructible. It practically is, but unfortunately it destroyed my phone. To install it you have to spray this liquid on the back of the 'shield' and apply it to your phone, using a squeegee to get the bubbles out. It went pretty well, and I was happy with the results, but 3 days later my screen stopped working.
Everything is washed out, and it looks like water got inside the LCD somehow. For instance, colors streak across the LCD in fonts, etc.
I called ATT and they are mailing a replacement, and I'll be expected to send this phone back. They said if the return phone has damage that would void warranty (water damage, etc) I'll be prorated $400 on my next bill.
Over the phone the customer representative had me remove the battery and check one of the water damage pads to make sure it was white. It is.
For those who have seen internal phone assembly, is there any of these directly by the screen that will pick up moisture?
As far as ATT knows, the phone LCD suddenly stopped working. I'll get a replacement and /hopefully/ theres not a moisture pad right next to the LCD assembly. Anyone know?
Damn, hate those broken screen story's. Scars the **** out of me.
jon_k said:
This question is directed to those who have taken apart their Kaiser, and specifically screen the screen assembly. I've got water issues and the screen is broke now. Here's the story. I might get some outrageous warranty charges.
I installed the InvisiShield (www.shieldzone.com) on my phone. Essentially it's a screen protector that is indestructible. It practically is, but unfortunately it destroyed my phone. To install it you have to spray this liquid on the back of the 'shield' and apply it to your phone, using a squeegee to get the bubbles out. It went pretty well, and I was happy with the results, but 3 days later my screen stopped working.
Everything is washed out, and it looks like water got inside the LCD somehow. For instance, colors streak across the LCD in fonts, etc.
I called ATT and they are mailing a replacement, and I'll be expected to send this phone back. They said if the return phone has damage that would void warranty (water damage, etc) I'll be prorated $400 on my next bill.
Over the phone the customer representative had me remove the battery and check one of the water damage pads to make sure it was white. It is.
For those who have seen internal phone assembly, is there any of these directly by the screen that will pick up moisture?
As far as ATT knows, the phone LCD suddenly stopped working. I'll get a replacement and /hopefully/ theres not a moisture pad right next to the LCD assembly. Anyone know?
Click to expand...
Click to collapse
I dont know but man I hope that there isn't. Have you tried contacting invisishield? Never mind, b/c they'll blame you. Most applicators like that use alcohol to evaporate the remaining moisture that's left. My friend applied it to his, and he used very little liquid(scared), so GOOD LUCK!! I MEAN IT
Tough break, sounds dangerous to pour liquid on the screen though !
On a related matter has anyone seen pics of a Kaiser pulled apart ? Still wondering where the GPS antenna is located !
Yeah, I hope I don't get shafted.
I love the invisibleshield, and I put one on my $1,500 DSLR camera screen, but since the Kaiser screen is recessed a bit, when you squeegee the solution out from under the screen, it cannot be wiped away. It just gets pushed out between the phone's body bezel, and the screen glass -- right in to the phone. With my DSLR camera, the screen is flush with the body, so when squeegee'd I could quickly wipe the water/alcohol away.
Contacting Invisibleshield got me:
Our liability does not extend beyond our product. The lifetime warranty only covers the replacement of the invisibleSHIELD and NOT a warranty for the device the shield is protecting.
Click to expand...
Click to collapse
If ATT charges me the $400 if they find out, I guess I'll pay it. It's my fault, but by extension of invisibleshield. Guess I'll learn not to use that product on anything that has a recessed screen. I was thinking of buying an invisible shield for my laptop as well, but it's screen is slightly recessed like the kaiser, so you can forget me doing that!
xmoo said:
Damn, hate those broken screen story's. Scars the **** out of me.
Click to expand...
Click to collapse
That was why I bought the 'best screen shield on the market' for scratches (invisibleshield). Coincidentally that was the demise of my phone. I also purchased a steel case that basically would let me sit on my phone (uncomfortably) if i wanted. The desire to protect my phone, did the opposite in my case.
Wow what a horror story. Thanks for sharing with us - may prevent another phone from dying.
Wondering if you remove the battery and not using for a few days until the water dries out before turning it on?
zcink said:
Wow what a horror story. Thanks for sharing with us - may prevent another phone from dying.
Wondering if you remove the battery and not using for a few days until the water dries out before turning it on?
Click to expand...
Click to collapse
Could be, zcink. The replacement phone is on it's way. I can remove the battery during this time it takes for the replacement to come and see what happens. Unfortunately, I think one of the following has happened:
1) Water seeped between the LCD protetcive glass, and the LCD itself, and somehow soaked in to the LCD causing mini shorts -- thus resulting in kludged text.
2) Water seeped to the phone's connecting cable where the screen input is, dried on the wires, thus creating a short -- destroying the signal.
Either way, when the liquid dry's, the mineral deposits causing the short will still exist, still causing a short. For both, repair requires disassembly, voiding my warranty. I could buy a new replacement screen from the China place for about $100, but if ATT /might/ replace it without screwing me, I'll take the chance. Just wanted to know what my chances /were/ them finding out it's got water in it.
I guess the moral is.
Don't buy from InvisibleShield, unless you use a SPARING amount of spray they they include. They include a huge bottle, and I used 2 sprays worth applied to my shield. This created enough excess to be squeegeed right into my phones body. The phone worked great for a few days, until one day at work, while I was using it -- BAM -- the screen was dead.
There isn't the water dectector there, but I'm pretty sure the technicians would notice the damaged screen.
I know those screen protectors, used them for alot of things. Using one right now actully. Its the one you wash with soap and warm water, and just let it dry, it have a static adhesive to the the scree.
I see. yeah hopefully the ATT tech will be lazy and just grant you the warranty without investigating. just play dumb. If they charge you the $400 call them up and threaten to switch to T-Mobile.
My phone died and T-Mobile was going to do nothing until I threatened to switch to ATT, then they replaced it.
I seriously doubt that they will be able to tell unless you really soaked it, next time use a dry screen protector, they work just fine, no bubbles. The only moisture sensor is on the battery, and if it was a tiny amount of moisture, there's likely no signs in the screen assembly. AT&T isn't likely going to dissect the screen to check.
Kaiser disassembly howto
I have found this one somewhere here, can't remember where... Hope this helps.
http://www.mediafire.com/?0ly2msnybhb
Hadn't heard of that screen protector before, guess it would work well on an HTC Touch, not sure how the "full body" version works though!
gabriel31337 said:
I have found this one somewhere here, can't remember where... Hope this helps.
http://www.mediafire.com/?0ly2msnybhb
Click to expand...
Click to collapse
Amazing find. Thanks!
It appears to me that the screen itself is it's own modular unit. Meaning, after phone disassembly, you'd have to disassemble the actual screen itself. Further, there is no moisture indicators directly by the assembly it seems.
Knock on wood, but I'd hope a tech wouldn't go that far to determine the fault of the phone. I assume they would if theres telltale signs of water damage to the display (streaking might be a common sign.) But, maybe, just maybe, they won't.
http://www.gpspassion.com/download/HTC_Kaiser_disassembly.pdf
updating link
RemE said:
The only moisture sensor is on the battery
Click to expand...
Click to collapse
The service manual shows 4 of them, one under the battery that can be seen from the outside, one at the top and one at the bottom of the mainboard's other side, and.. one on the board that holds the bottom front panel switches, so very close to the LCD.
Personally I wouldn't have asked for a replacement phone, I'd have disassembled the phone and tried to clean it if made dirty by the liquid, bought a spare screen off ebay if it was definitely dead, and if ultimately it didn't work bought another phone off ebay for less than $400. But maybe I like risk
Here, Perfect for what you need, used it myself: http://www.mindsofwisemen.com/fileso/other/ReplacingTheLCDonaKaiser.pdf
Best wishes
Mod Edit:
Not sure if the above noted guide is officially and with permission uploaded to that site, but to give credit to members here it is (SKDVR’s Adaption of Tony Chen’s guide)
http://forum.xda-developers.com/showpost.php?p=2247685&postcount=19
i took mine apart to replace the screen; pics and info on what i did and where i got it. didn't see any water indicators near the screen when i did it, didn't think to look...
Keyboard membrane removal.
So, I've had trouble with my keyboard lately and wanted to just clean off the contacts on the membrane...but I can't seem to get the damned thing out of the plastic keyboard Middle Housing.
I have gotten everything apart so the housing is separated. Verified that I did it the way the service manual says...but i saw NOTHING about how to disassemble the keyboard from the housing.
PLZ! Pictures are good.
Try replacing digitizer screen
found that digitizer screen is above lcd and can be purcased for about $10 on ebay
hello guys,
my tytn II cant detect simcard saying the simcard is missing.
Any idea whats wrong???
lots of ebay products claims to be OEM, but i smell knock off (aftermarket). my guts tells me i will regret buying from most of the obeyers who claims OEM/new .. of course their prices are tempting, for example most of them offering a range from $63 - $69..
if you bought a screen, let me know where did you buy it from, and how good it is?
what do you recommend, such as going after used ones that are pulled from previous one etc?
thanks
I'm in the same boat as you. Dropped my G2 while getting off pickup truck and the digitizer is kaput. I have no touch response anywhere on the screen. But the LCD is working really well. No damages to that.
So i'm looking for a digitizer as well to replace it.
gunemalli said:
I'm in the same boat as you. Dropped my G2 while getting off pickup truck and the digitizer is kaput. I have no touch response anywhere on the screen. But the LCD is working really well. No damages to that.
So i'm looking for a digitizer as well to replace it.
Click to expand...
Click to collapse
i am looking for the LCD and digitizer assembly. but i am trying to find OEM part
sdcaliber said:
lots of ebay products claims to be OEM, but i smell knock off (aftermarket). my guts tells me i will regret buying from most of the obeyers who claims OEM/new .. of course their prices are tempting, for example most of them offering a range from $63 - $69..
if you bought a screen, let me know where did you buy it from, and how good it is?
what do you recommend, such as going after used ones that are pulled from previous one etc?
thanks
Click to expand...
Click to collapse
When my wife broke the digitizer on her n4, I was in the same boat. I searched earnestly for TRUE OEM parts. What I discovered was this site:
http://www.etradesupply.com/catalogsearch/result/?q=LG+VS980
They are the most expensive, but to my knowledge it is TRUE OEM.
Due to time constraints, I ended up getting a screen on Amazon that claimed to be OEM, and while the screen and digitizer assembly I could tell were brand new OEM parts, the housing had been recycled, as it was missing some adhesive for the board components. While her screen works fine now, it lacked the filter for the led notifications light (as it was a recycled housing) and was more difficult to replace due to the fact I had to conserve the adhesive film off the old housing and transfer it to the new housing. If I had to do it again, I would pay the extra and get the TRUE OEM brand new from etradesupply.com
Good Luck!
PS. If you need a good youtube video for the repair, I recommend this guy: https://www.youtube.com/user/LE55ONS
housing is not an issue
Lttlwing16 said:
When my wife broke the digitizer on her n4, I was in the same boat. I searched earnestly for TRUE OEM parts. What I discovered was this site:
http://www.etradesupply.com/catalogsearch/result/?q=LG+VS980
They are the most expensive, but to my knowledge it is TRUE OEM.
Due to time constraints, I ended up getting a screen on Amazon that claimed to be OEM, and while the screen and digitizer assembly I could tell were brand new OEM parts, the housing had been recycled, as it was missing some adhesive for the board components. While her screen works fine now, it lacked the filter for the led notifications light (as it was a recycled housing) and was more difficult to replace due to the fact I had to conserve the adhesive film off the old housing and transfer it to the new housing. If I had to do it again, I would pay the extra and get the TRUE OEM brand new from etradesupply.com
Good Luck!
PS. If you need a good youtube video for the repair, I recommend this guy: https://www.youtube.com/user/LE55ONS
Click to expand...
Click to collapse
i looked at etradesupply, but i searched on google on them and there are many allegation they are not OEM, and their delivery time/shipping are not something you want to deal with. been said that, i am only looking for LCD and digitizer assembly as i can assemble them into the housing myself, i have already took apart the older screen out of the housing without a problem.
I bought from ebay one of the ones claimed to be an origiginal oem screen. Works perfect and do blemishes etc.
i bought one
squee666 said:
I bought from ebay one of the ones claimed to be an origiginal oem screen. Works perfect and do blemishes etc.
Click to expand...
Click to collapse
i did buy one from ebay today, after been an annoying person with lots of questions hahaha. i refused to buy from anyone below 99% profile credential on ebay. here are the questions i asked lol
Is the LCD screen manufactured by the same company that I would find on brand new in box phone that I purchased from an authorized store? if not, is the same Quality, TRUE IPS LCD with Gorilla Glass 2 digitizer?
Is this LCD part brand new or refurbished from reclaimed old parts?
Digitizer – Is the Touch Panel manufactured by the same company that I would find on brand new in box phone that I purchased from an authorized store?
Digitizer – Is the Touch Panel new or refurbished, or reclaimed from old parts?
and if I bought a brand new in box sealed G2 from LG, the part I’m asking about would be 100% identical with no differences in quality or condition?
does it work on D800 model, if not do you have one that works with D800 that is a genuine OEM?
is it OEM (Original equipment manufacturer), does it have part number on the flex cable, and LG display co,ltd label ?
only one seller, answered all of them concisely, without political correctness or avoidance. lots of them stopped talking to me, and some only answered vaguely. i had one hilarious response, who said the the screen is OEM but not genuine, i insisted for him to elaborate, he said OEM but not original. all of us know that OEM stands for Original equipment manufacturer. i sent him a response, that it does not make sense to be OEM but not original. he replied back OEM for them is, Optical equipment manufacturer lol, heck i do not even know what does that mean lol. i took a screenshot of the definition and sent it to him, he never replied back hahaha. many shady seller on ebay
P.s once i receive the part and install it, i will update on the condition/quality
can post the link for the seller you bought the assembly?
thank you!
Link
noris08 said:
can post the link for the seller you bought the assembly?
thank you!
Click to expand...
Click to collapse
http://www.ebay.com/itm/251591046010?_trksid=p2060778.m2749.l2649&ssPageName=STRK:MEBIDX:IT
working
update,
as i provided previously with the link of the LCD/Digitizer, i promised to update after purchase and assembly.
i self repaired myself, took me about an hour and Half give or take. it works like a charm, no problem whats so ever.
advise, before attempting to do it yourself, find a youtube video of how to disassemble and reassemble, including how to apply the adhesive (took most of the time).
i can confirm, and take my words for it, the one i bought is an OEM LCD digitizer.
cheers,
sdcaliber said:
update,
as i provided previously with the link of the LCD/Digitizer, i promised to update after purchase and assembly.
i self repaired myself, took me about an hour and Half give or take. it works like a charm, no problem whats so ever.
advise, before attempting to do it yourself, find a youtube video of how to disassemble and reassemble, including how to apply the adhesive (took most of the time).
i can confirm, and take my words for it, the one i bought is an OEM LCD digitizer.
cheers,
Click to expand...
Click to collapse
Can you provide any info on how u got the screen to securely cit in the frame, like what adhesive did u use and how u did it?
I did the repair my self the phone works great except the bottom ov the screen, sticks out abit n I can see the back light, very annoying
jamracer said:
Can you provide any info on how u got the screen to securely cit in the frame, like what adhesive did u use and how u did it?
I did the repair my self the phone works great except the bottom ov the screen, sticks out abit n I can see the back light, very annoying
Click to expand...
Click to collapse
absolutely,
keep in mind the following things,
i used 3mm double sided adhesive tape, you can find them on ebay for 2 dollars give or take. the hard part laying out the tape in correct manner. you have TWO WAYS to do it that i know of using the tape, whatever that suits you. first one, most people will place the tape on the housing (if you did that, avoid placing the tape over the proximity sensor, camera, the usb, and the connection ports. or it will be a pain to remove them and damage maybe imminent in such situation ). the trick part, is the tape in vertical position around the edges where the bezels of the screen will sit (if its done incorrectly, you will have the problem you have described). therefore i will share the second method, my method :
check if the screen and digitizer works correctly before finally putting the adhesive;
WARNING: if you are not sure what you are doing, please consult with phone technicians for a professional fix. this is only my method/my opinion and in no way constitute a professional advise.
it is separated in to three parts
1 - use 3mm tape to tape the bottom and top of the housing, i repeat do not tape, the proximity sensor, camera, the ports, or the usb, use common sense or youtube to see which one is which .
2 - use the 3mm tape and tape the edges behind of the screen under the bezel (on the screen/digitzer assembly itself, not the housing). it is a narrow spot to tape, that where most people end up with popping out screen at the bottom edges and seeing the light. due to the narrow edges, use a small tweezers to place it.
3- use the 3mm tape and tape the edges of the housing where the bottom of the screen will sit (optional). in my case, i did that also
now peel the double sides 3mm tape, using tweezers will make it easier, much much easier.
once done, take your screen/digitizer assembly, and insert the bottom flex cables first into the housing (they are two cables, be careful, they are fragile), make sure the bottom part sit perfectly and all the cables are sitting correctly into the housing, before you insert the top flex cable (longer thinner cable).
insert the flex cable (the top one, into the housing slowly, while checking around with your eyes, that everything is aligned with the housing. once the flex cable in, double check and see if the flex cable is seated perfectly. check around the phone edges, and if everything is perfect, press gently on the edges, until the adhesive makes contacts. if you find that the screen is not sitting correctly, gently lift the phone slowly, and position it correctly before the adhesive sticks (takes about two minutes before the adhesive taking effects, keep that window in mind).
after the everything is sitting where it suppose to, place everything back inside the phone, turn it on and check again if its working along with the digitizer (i recommend checking whether the screen and digitzier works before placing the adhesive). once you check everything is working fine, turn the phone off, and unplug the battery cable from the motherboard.
use hair dryer (on low) or heat gun (use low temperature), hair dryer is safer if you are not sure what temperature to use with the heat gun and heat around the edges of the screen (keep it moving and do not stay in one place) this is for the final seal, about 30 to 40 seconds of heating. now the screen is sealed shut. leave the phone to cool down for a minute (optional: use a rubber band around the top and bottom for added pressure, not too tight though). plug the battery cable in and reassemble the phone.
cheers
sdcaliber said:
absolutely,
keep in mind the following things,
i used 3mm double sided adhesive tape, you can find them on ebay for 2 dollars give or take. the hard part laying out the tape in correct manner. you have TWO WAYS to do it that i know of using the tape, whatever that suits you. first one, most people will place the tape on the housing (if you did that, avoid placing the tape over the proximity sensor, camera, the usb, and the connection ports. or it will be a pain to remove them and damage maybe imminent in such situation ). the trick part, is the tape in vertical position around the edges where the bezels of the screen will sit (if its done incorrectly, you will have the problem you have described). therefore i will share the second method, my method :
check if the screen and digitizer works correctly before finally putting the adhesive;
WARNING: if you are not sure what you are doing, please consult with phone technicians for a professional fix. this is only my method/my opinion and in no way constitute a professional advise.
it is separated in to three parts
1 - use 3mm tape to tape the bottom and top of the housing, i repeat do not tape, the proximity sensor, camera, the ports, or the usb, use common sense or youtube to see which one is which .
2 - use the 3mm tape and tape the edges behind of the screen under the bezel (on the screen/digitzer assembly itself, not the housing). it is a narrow spot to tape, that where most people end up with popping out screen at the bottom edges and seeing the light. due to the narrow edges, use a small tweezers to place it.
3- use the 3mm tape and tape the edges of the housing where the bottom of the screen will sit (optional). in my case, i did that also
now peel the double sides 3mm tape, using tweezers will make it easier, much much easier.
once done, take your screen/digitizer assembly, and insert the bottom flex cables first into the housing (they are two cables, be careful, they are fragile), make sure the bottom part sit perfectly and all the cables are sitting correctly into the housing, before you insert the top flex cable (longer thinner cable).
insert the flex cable (the top one, into the housing slowly, while checking around with your eyes, that everything is aligned with the housing. once the flex cable in, double check and see if the flex cable is seated perfectly. check around the phone edges, and if everything is perfect, press gently on the edges, until the adhesive makes contacts. if you find that the screen is not sitting correctly, gently lift the phone slowly, and position it correctly before the adhesive sticks (takes about two minutes before the adhesive taking effects, keep that window in mind).
after the everything is sitting where it suppose to, place everything back inside the phone, turn it on and check again if its working along with the digitizer (i recommend checking whether the screen and digitzier works before placing the adhesive). once you check everything is working fine, turn the phone off, and unplug the battery cable from the motherboard.
use hair dryer (on low) or heat gun (use low temperature), hair dryer is safer if you are not sure what temperature to use with the heat gun and heat around the edges of the screen (keep it moving and do not stay in one place) this is for the final seal, about 30 to 40 seconds of heating. now the screen is sealed shut. leave the phone to cool down for a minute (optional: use a rubber band around the top and bottom for added pressure, not too tight though). plug the battery cable in and reassemble the phone.
cheers
Click to expand...
Click to collapse
thanks alot of the info,
i did the repair and all, the screen and digitizer works well, its just the bottom of the screen sticks up, i went ahead n ordered a roll of 3m 300lse double side tape, the dounble side tape i hav is just the regular black tape, dont think its strong enough, i will go over everything with a fine tooth comb when it arrives, i hav a sprint g2 on its way as well, do u know if the d800 and the ls980 frame is compatible??
thanks for the info really detailed
sdcaliber said:
i looked at etradesupply, but i searched on google on them and there are many allegation they are not OEM, and their delivery time/shipping are not something you want to deal with. been said that, i am only looking for LCD and digitizer assembly as i can assemble them into the housing myself, i have already took apart the older screen out of the housing without a problem.
Click to expand...
Click to collapse
I bought EB40 battery for Atrix HD through Etradesupply's Amazon store. I haven't had any issues with battery and lasted as promised.
Whole purpose of that project was to put battery from Droid Maxx into Moto Atrix HD and bump up capacity from 2100mah to 3300 mah.
May be different buyers have different experience or I just got lucky.
jamracer said:
thanks alot of the info,
i did the repair and all, the screen and digitizer works well, its just the bottom of the screen sticks up, i went ahead n ordered a roll of 3m 300lse double side tape, the dounble side tape i hav is just the regular black tape, dont think its strong enough, i will go over everything with a fine tooth comb when it arrives, i hav a sprint g2 on its way as well, do u know if the d800 and the ls980 frame is compatible??
thanks for the info really detailed
Click to expand...
Click to collapse
3m 300lse double side tape should be fine, as long as you use it correctly.
in regards to the frame, well that i am not sure about it. however, the LCD/digitizer i ordered was labeled OEM LS980 (sprint) VS980 (Verizon) and compatible with D800 (att- that is mine) and D801. so far, it fits perfectly. make sure it is OEM, if its not, the cut maybe off, that results discrepancy in fitting with the frame. also, double check with the seller, if the its compatible with your phone.
cheers
sshark said:
I bought EB40 battery for Atrix HD through Etradesupply's Amazon store. I haven't had any issues with battery and lasted as promised.
Whole purpose of that project was to put battery from Droid Maxx into Moto Atrix HD and bump up capacity from 2100mah to 3300 mah.
May be different buyers have different experience or I just got lucky.
Click to expand...
Click to collapse
yeah maybe, all depends of course. most of these products are subject to opinions if there is doubt about their OEM legitimacy. but for me, i will not buy non OEM for battery again, it scares the hell out of me. let's say i had a horrible experience before. i had Note 3, and bought a battery for it. the extra capacity made me drools lol, so i went with it. days later, i found the phone in total meltdown, literally. woke up from my sleep, and the phone is melting/fire.... scary scary experience. the good thing, i do not sleep while my phone next to me. it was on my table, charging.
side not: the original battery of Note 3 malfunctioned
OEM
sdcaliber said:
lots of ebay products claims to be OEM, but i smell knock off (aftermarket). my guts tells me i will regret buying from most of the obeyers who claims OEM/new .. of course their prices are tempting, for example most of them offering a range from $63 - $69..
if you bought a screen, let me know where did you buy it from, and how good it is?
what do you recommend, such as going after used ones that are pulled from previous one etc?
thanks
Click to expand...
Click to collapse
I bought it on Ebay and now it´s working fine, nice!!.. First I bought only the digitizer and it was faulting, but now this assembly is really working fine:
http://www.ebay.com/itm/281280382756?ssPageName=STRK:MEWNX:IT&_trksid=p3984.m1439.l2649
Regards,
Just posting to share my experience. I bought a replacement lcd\digitizer for my G2. Once installed, i had white lines going up and down the screen.
Some devices use different panel hardware (JDI instead of LGIT) and you will have white lines after using patched kernel. You must use those kernel with "_jdi" in its name. More info:http://forum.xda-developers.com/show...&postcount=122
After flashing the new kernal the phone works great. The phone does get noticeably hotter, unfortunately, which is a little worrisome.
The kernal issue and the heat lead me to believe that what i bought was not oem.
Sent from my LG-D801 using XDA Premium 4 mobile app
Is D800 frame compatible with LS980?
sdcaliber said:
3m 300lse double side tape should be fine, as long as you use it correctly.
in regards to the frame, well that i am not sure about it. however, the LCD/digitizer i ordered was labeled OEM LS980 (sprint) VS980 (Verizon) and compatible with D800 (att- that is mine) and D801. so far, it fits perfectly. make sure it is OEM, if its not, the cut maybe off, that results discrepancy in fitting with the frame. also, double check with the seller, if the its compatible with your phone.
cheers
Click to expand...
Click to collapse
I was just working on a frame lcd assembly swap on an LS980 rev 1. The frame I bought was a Verizon LV980 and the vibrator was off buy at least 3mm, I didn't mind losing the vibrator to gain a good lcd. Then the proximity detector layout was different, the LS980 had an extra piece that fit in a hole, but it could be removed. About 5mm below that is a ground connector for the motherboard on the LS980 but not on the VS980 and the tab holding the antenna coax hit the motherboard making the frame about 0.5mm too small causing the mobo not to seat.
All of these could be amended. Shave 0.5mm of the soft metal chassis, very easy, mobo grounds in at least six other places and proximity sensor had a removable tab.
But the bottom of the chassis where the dock port/usb board sits was just too different, the LS980 daughterboard wouldn't seat, it was larger. It could be forced but only at an angle that made the usb port off-center and not parallel to the opening. My repair stopped and re-assembled the phone with the LS980 chassis complete with my damaged lcd.
-----attached pics of proximity sensor, and ground connector area, didn't take more, I was getting mad.
sdcaliber said:
i looked at etradesupply, but i searched on google on them and there are many allegation they are not OEM, and their delivery time/shipping are not something you want to deal with. been said that, i am only looking for LCD and digitizer assembly as i can assemble them into the housing myself, i have already took apart the older screen out of the housing without a problem.
Click to expand...
Click to collapse
Actually I bought an LCD from this company. I am very happy with it. It is true HD and the it was shipped for me in 3 days as they said. At first I was very worried with the comments but I took the risk and I am satisfied with it. I don't know why others complain about it but I recommend them.
Hi everyone,
Hope my question makes sense - I dropped my phone last night and the screen cracked. Not the LCD, just the glass. But... The touch is perfect. There's just cracked glass.
I saw a listing in eBay that had just the "front glass" cover part for like $6. Naturally, if I can NOT pay $250+ for a fixed phone, that'd be great. So, does anyone know what exactly it is that I'd need to buy to fix this myself?
Thanks in advance!
EDIT: This link has the "glass lens" I was talking about.
http://www.etradesupply.com/motorola-nexus-6-glass-lens-black.html
The glass and digitizer are almost always fused together. If you can get them seperated you'll likely never get the replacement glass attached in a way that will look normal. These things are typically replaced as a unit because of this.
They come glued together and actually removing the glass lens without damaging anything else is very VERY difficult. Best option is to buy a new LCD/digitiser in one and swap them out. I know its expensive but i can ensure you trying to change just the glass is a nightmare!
I've done a couple screens like this and they are a PITA!
If you heat them up enough you can separate the two but in some cases the heat needed damages the screen. It's one of those things that you can "try" it but go into it knowing that it most-likely won't work unless you have a ton of patients. The key is getting all of the glue that bonds the two parts off of the screen/digitizer so the new glass can lay flat and seal.
Interesting. Does the glass not need to be rebonded?
This morning I was cleaning my phone (getting rid of the finger prints/smudges) while standing up when it slipped out of my hand and hit the tiled floor. Everything is fine except the screen (which is cracked). Screen works fine but is unresponsive no matter where I press or touch the screen. How much does a Z3 Compact replacement screen cost? I searched around and it seems it is about $100?
Screen replacement costs in Poland +/- 135$
(authorised sony service)
Yes' it's hard to get original one cheaper than 100-120$. You can search for some Chinese replacement cause sometimes it looks quite similar to original one but You must check it before buying. Last time I had a client with Z1c replacement screen which he bought for 40$ and there was no white color, everything what should be white was purple.
Voids warranty, cheap replacement
Got mine from here replacebase dot co dot uk (can not post links ), of course you void your warranty if you do it yourself.
Parts are good quality till now. I advice to order a back glass too, I broke mine when taking it out and had to reorder again (costs approx 6 pound).
Next time just heat up back glass with hair dryer and You wont break it.
Chamelleon said:
Next time just heat up back glass with hair dryer and You wont break it.
Click to expand...
Click to collapse
Thanks for the input
The problem was a small crack which did not matter until you have to remove it, you can not pull on it when its cracked. Anyway I will use a hair dryer to put it back together (assemble, heat up, press with books).
Thanks for the replies.
I'll be getting the repair done from the official Sony shop/distributor I bought the phone from. Just wanted to get an idea of how much it "should" cost before I approach them.
m4mbax said:
Thanks for the input
The problem was a small crack which did not matter until you have to remove it, you can not pull on it when its cracked. Anyway I will use a hair dryer to put it back together (assemble, heat up, press with books).
Click to expand...
Click to collapse
Hello
I have tried to change my backglass 3 times but after a few hours the glass falls off... (Yes, I cleaned the phone removing all the old adhesive - and yes, I had pressure on it over night ) But all the instructions I have found on the internet never mentioned anything about putting the glass on, and HEATING it up, and the putting pressure on it... Where have you found that advice? You could imagine that heating up would ruin the adhesive/making it thinner and thereby not waterproof...? But on the other hand your succesrate probably beats mine...
Foxhunter123 said:
Hello
I have tried to change my backglass 3 times but after a few hours the glass falls off... (Yes, I cleaned the phone removing all the old adhesive - and yes, I had pressure on it over night ) But all the instructions I have found on the internet never mentioned anything about putting the glass on, and HEATING it up, and the putting pressure on it... Where have you found that advice? You could imagine that heating up would ruin the adhesive/making it thinner and thereby not waterproof...? But on the other hand your succesrate probably beats mine...
Click to expand...
Click to collapse
I think it was a comment below the iFixit tutorial. But one big warning here, I did extra maximally stupid and put it to 'press' under my table (with books around it). The table was too heavy and cracked my front screen once again :crying:
+ The rear glass sits fixed and has not loosened.
- Don't put too much pressure or you destroy it yet again like stupid me
m4mbax said:
I think it was a comment below the iFixit tutorial. But one big warning here, I did extra maximally stupid and put it to 'press' under my table (with books around it). The table was too heavy and cracked my front screen once again :crying:
+ The rear glass sits fixed and has not loosened.
- Don't put too much pressure or you destroy it yet again like stupid me
Click to expand...
Click to collapse
Doh!!! ? I have also read on Ifixit and can see there are different opinions about if it is nessesary to heat or not. But I think I will follow your advice and heat the new back before putting it under (less pressure) ?.
Another thing I read on Ifixit is that someone writes that you should put on an adhesive sticker - eventhough the new back comes with adhesive already on...? What is your advice on this?
Most pre-glued adhesive stickers on back are useless. Now everytime I change back in Xperia Z, Z1, Z2, Z3 and compacts I need to remove pre-glued sticker and change it to original one. Many times I had complaint on it from my clients saying that back glass came off. So it's better to order original back glass or just original adhesive.
Foxhunter123 said:
Doh!!! I have also read on Ifixit and can see there are different opinions about if it is nessesary to heat or not. But I think I will follow your advice and heat the new back before putting it under (less pressure) .
Another thing I read on Ifixit is that someone writes that you should put on an adhesive sticker - eventhough the new back comes with adhesive already on...? What is your advice on this?
Click to expand...
Click to collapse
Good
Mine came with the adhesive ON the screen, I used that one, I didn't have a separate one. Be extra careful when 'placing' the adhesive where it belongs because you can not remove it once place (okay maybe slightly). Its important that it fits on the first to first and a half try. More adhesive means thicker layer --> glass will stick out
Anyway, most of the stories you read online are partially BS, the phone will work even when the glass is a tiny bit loose or when the adhesive rotated and is a bit thicker in one place. In my eyes, when you dared to order, you are very much capable of assemble the parts.
In btw, ordered new glasses today, hope my two left hands fix it this time.
PS: A lesson I learned on a friends Galaxy S2, do NEVER EVER try to use force when something sticks or is not as loose as in a video. Google or ask another person maybe you just dont do the trick. A connector didnt want to come off so we used a lever to lift it, CLICK, the place where the lever levered broke the board... :silly:
Edit 1: I think its not necessary to HEAT it, it just has to be a lil bit warmer than in your pocket or when calculating heavily. 30s under a hairdryer will be more than enough i guess.
Forgot to update this thread. I received my fixed phone last week. They replaced the screen and even the "bumpers" around the phone for $98. They even delivered the phone to my home free of charge. Looks brand new, all the minor dings I had on the phone are gone.
On another note, I also bought my first iPhone. Got an Space Gray iPhone 6s 128 GB with the official/Apple leather case for the 6s. Got it last Thursday. Been playing around with it a lot and, overall, I love it. Deciding on whether to keep my Z3 Compact as a back-up phone or just sell it. But geez, does the iPhone 6s load games and other apps fast (thanks to its NVMe storage).