Database Develop

Camera hard button not working

I don't really use the camera on my Kaiser, but I've just notice that on pushing the camera button it does not start up. No problem selecting from the program list.
Check that the button was set up correctly in the settings screen. I then changed the button to operate another program, but that doesn't work either. Somethings up with the button itself. I do get the "audio click" confirming the button has been pressed but nothing else.
Any ideas?
Kevin

Speedmaster said:
I don't really use the camera on my Kaiser, but I've just notice that on pushing the camera button it does not start up. No problem selecting from the program list.
Check that the button was set up correctly in the settings screen. I then changed the button to operate another program, but that doesn't work either. Somethings up with the button itself. I do get the "audio click" confirming the button has been pressed but nothing else.
Any ideas?
Kevin
Click to expand...
Click to collapse
From what you say it sounds like you are well aware of how that switch works and that it has two levels of operation (half press and full press). With full press - required to start the camera, it really is a deep press, going down below casing level.
I assume though you know this and have tried pushing in as deep as it will go. It is obviously at least partially working hence the audio sound.
To be honest a hard reset might well fix this and if not the a repair under warranty for a hardware fault could be done.
Mike

That's it. It works now. What's the half press for?

Speedmaster said:
That's it. It works now. What's the half press for?
Click to expand...
Click to collapse
Half a press focuses the camera and then a full press takes the picture.
Previous models didn't have auto-focus

TechXL said:
Half a press focuses the camera and then a full press takes the picture.
Previous models didn't have auto-focus
Click to expand...
Click to collapse
Yes indeed, it's also configurable in settings so you can change the half and full press behaviour.
Mike

Keyboard not working

I have a problem with my Kaiser. The keyboard and the front buttons do not work anymore. Only the center front button and the right side stand-by button are working.
I read here on the forums that it can be a software problem? I didn't made any rom update or other chages, I used the phone as it was from the start. After 2 months of using I got this problem with the keyboard. Any advice or should I get the phone to the Service?
I tried soft reset and after that a hard reset (I backed up the data with Sprite), but the problem persists.
Another thing: not making any changes in keys mapping I noticed that the right side stand-by button was mapped for voice recording! That was quite strange, when I activated the screen in the same time it began recording voice. I correctly remaped the button as it was, but again I don't know how it changed by itself...

when you did the hard reset, did you restore your backup right away? or did you test the buttons right after the hard reset?

I've testet the buttons before making the restore. They had the same problem: not working and the stanby button was also mapped as voice recording.

geovadim said:
I've testet the buttons before making the restore. They had the same problem: not working and the stanby button was also mapped as voice recording.
Click to expand...
Click to collapse
after a hard reset the power button was set to voice recording? When you refer to the standby button, do you mean the power button?
If in deed you did a Hard Reset then the device would be back to default settings. If you are getting the power button mapped to voice recording then your device is f**ked up badly, or at least the ROM is trashed.
you sure you didn't try to flash your rom or SPL?

smittyofdhs said:
after a hard reset the power button was set to voice recording? When you refer to the standby button, do you mean the power button?
Click to expand...
Click to collapse
No, after the hard reset the voice recording was still mapped... When I reffer to the stanby button I mean, yes, the power button.
smittyofdhs said:
If in deed you did a Hard Reset then the device would be back to default settings. If you are getting the power button mapped to voice recording then your device is f**ked up badly, or at least the ROM is trashed.
you sure you didn't try to flash your rom or SPL?
Click to expand...
Click to collapse
Absolutely not! I am not a informatician to play with this kind on mods and installs. I only had my software (YM, iGo etc). Never tried to update or change the rom or the SPL.
If it is like you say, this it can't be repaired in the service?

the same problem, but i have a little more strange things:
- device still mapping power (standby) button for voice commander, even after few hard resets without restoring any previous data
- holding power button mapped for record, so after hard reset, even before aligning screen, device starts recording
- when i'm on a desktop, pressing twice power button (off/on), device going to calling screen and trying to found contact that starts with "edfc"
- when i'm in contacts, pressing twice power button (off/on), device trying to found contact in search, that starts with "edfc"
- keyboard doesn't work, front buttons also too
- when i'm typing any message in notes, for example, i can't erase it - backspace button on virtual keyboard doesn't work also
So, what are you thinking about that? Can anyone help me?
Added:
- can't get into bootloader screen (power+camera+reset)
- in Android front buttons are works, keyboard - too, except 4 buttons. guess which? e,d,f,c
Added:
- re-flashing SPL and few ROM's doesn't help

Anyone?
Or I need get prepared to buy another one?

definitely sounds like a hardware issue. you could disassemble it and check if there are any lose connectors

ok. i've checked with another motherboard and the problem is - ... motherboard. can't be more specific right now, i'll try to find out more.

sigh.....sounds spendy. Been having the same issues, if its the motherboard dont know if i should just hold out on fixing it for a touch pro 2 and use my old nokia for a while. hmmmm, hopefully its not something super spendy. Never thought i would miss my tilt so much T_T

Backlight problem

My screen will be darker after 10 sec.
I can set this again to 5 min. and after a few on and offs it will be back at 10 sec.
This is very annoying!
I thought i had found the problem, but it wasn't.
HKCU/ControlPanel/Backlight/BatteryTimeout setting up to 300. This is 5 minutes. It counts in seconds. But this isn't working.
Please can anyone help me?? A lot more have this problem.

I have the same problem, anyone the solution?

same problem here. I have call the helpdesk of htc they told me to do a hard reset. But it doesn't work for me. They also told me to return the phone when the problem stays afther a hard reset

vipinholland said:
same problem here. I have call the helpdesk of htc they told me to do a hard reset. But it doesn't work for me. They also told me to return the phone when the problem stays after a hard reset
Click to expand...
Click to collapse
i had the same "problem" and indeed, after a hard reset the backlight stays on 2 minutes as my heart wishes. i also use the the option to "auto adjust backlight. i have to admit it is strange...i don't see the connection.

KukurikU said:
i had the same "problem" and indeed, after a hard reset the backlight stays on 2 minutes as my heart wishes. i also use the the option to "auto adjust backlight. i have to admit it is strange...i don't see the connection.
Click to expand...
Click to collapse
yes, my backlight stay's also on for 1 minute(my setting)...hope the sound problem is also gone..

It is a bug in keypad locking
I think the backlight problem only occurs if you are using the keylock feature by pressing the end call button for a couple of seconds.
You can try it out yourself:
1) set your backlight settings to whatever you want and verify it works as intended.
2) Now just normally switch of your phone (not locking the keypad) by pressing the power button, switch back on and verify that the setting is still correct.
3) Then do a soft reset and again verify that the setting is correct.
4) Now lock the keypad by using the end call button (press a couple of seconds until locked).
5) Now unlock the phone and check the backlight settings: they are put back on the default values!! I guess it is a bug in the keypad lock functionality.
Btw, step 2) and 3) are just for verification, you may skip these to reproduce the bug.

Actually, if you use the lock feature of the device (for instance by enabling AutoDeviceLock in the registry, see tweak 18 in the stickied Diamond tweaks thread) the settings are also reset to the default values.
Is this the case for everybody? Or is it just me that it seems the locking feature contains bugs.

FYI...I had this issue from the start when I was running the Asia HK 1.34 ROM image. I flashed it using HardSPL and put the Europe 1.35 image on the device and have not had the problem since. All backlight values work normally as of now....I recommend this if your device is the HK ROM and you're having the issue. Not sure if it'll work for you, but it worked for me....

The solution is simply
You have to change DWORD LockLevel present in HKEY_CURRENT_USER\ControlPanel\BackLight\LockLevel\ to 0 (zero)
And now your time of standby don't change anymore

Htc Tytn 2 Screen problem

Hi everyone,
I got a HTC Tytn 2 and i have a problem with it.
When i boot the phone it starts up and goes into windows like every windows mobile phone.
But when i press the standby button my screen wont go out of standby.
Only when i reset the phone it will work again.
Anyone got idea's ?

Oke, since no one responded.
Is there any way how i can make the Power Button replaced with the Speed Dial Button.
Because i think my power button is broke.

WGN88 said:
Oke, since no one responded.
Is there any way how i can make the Power Button replaced with the Speed Dial Button.
Because i think my power button is broke.
Click to expand...
Click to collapse
Have you at least tried backing up your data and doing a hard reset first ?

Yes, and i have also tried to put on a new rom and even updated the radio.
Iam a little bit out of idea's...

here are some more ideas:
1. how to test the power button: you say pressing the power button does not wake up the device once it goes to sleep. conversely, does pressing the power button put the device to sleep while the screen is on? if the power button is unable to make the device go off->on as well as on->off, then the power button is likely broken. if pressing the button achieves on->off, then the power button is probably ok and some software issue becomes more likely.
2. how to enable wake on pressing ANY hardware button: look for an option in Settings. i can't tell you the exact option because the ROM i am using does not have a link for this option, but this option does exist 100% in stock ROM and in lots of other ROMs. it contains settings like "Lock all buttons except power button" and "Keep all buttons unlocked" or something similar. by using the second option, pressing ANY hardware button while the screen is off will wake up the device.
3. you can use AE button plus to perform even more advanced button (re)mappings.
4. just to be sure that your device is really working correct, does the screen wake up when you call the phone or when you receive a text message? if it does not wake up even then, then search for "sleep of death".

Thanks for the response.
I think its a Service of Death problem.
Because when i try calling/smsing it, it wont go on
The buttons do work then...hopefully there's a fix for this problem...

Oke, i tried switching to 2G or 3G only but that didn't fix my Standby of Death.
I also bought a new sim card of vodafone so i wont get a No Sim error.
But what can i do now about it...it hangs like every 5 min...

Okay, after a will testing, the phone hangs every time its almost like when iam on the road with my tytn 2 and placing it upside down, it hangs.
But when iam putting it in the leather holder it doesn't hang.
Any had the same problems ?

WGN88 said:
Okay, after a will testing, the phone hangs every time its almost like when iam on the road with my tytn 2 and placing it upside down, it hangs.
But when iam putting it in the leather holder it doesn't hang.
Any had the same problems ?
Click to expand...
Click to collapse
Maybe it's hardware and something is coming loose

Noticeable delay after pressing screen lock button. System reset does not help.

This issue has been driving me mad for the past couple weeks. I'm at my wits' end and I need some expert help to figure this out. Please read this post thoroughly to understand my situation, as this is not a simple matter of uninstalling some apps.
When I first got my Note 9, the screen lock button worked perfectly. The screen would immediately turn on when I pressed the button, and it would immediately turn off when I pressed it again. However, once I got the Android Pie update, the screen lock button stopped working properly. The screen still turns on immediately, but there's about a 0.5 second delay after I press the button to turn it off. It's a relatively small issue, but it's enough to bother me.
I attempted to fix this by performing a system reset. But this did not help. In fact, this issue is still present even before completing initial setup of the phone.
When you perform a system reset, the first screen you see when your phone restarts is the welcome screen. It contains a "start" button that you press to begin setup. On this screen, the lock button issue does not happen. My phone locks and unlocks correctly. On the next screen, you connect to a wifi network. After connecting to a wifi network, the lock button issue becomes present. In other words, this issue with the lock button is present before I even start using the OS, or install any apps, or really do anything at all. It seems to be triggered by connecting to a wifi network during setup.
So I figured there must be something wrong with the firmware. So I used Odin to flash an earlier firmware version. This did not solve the issue. I even tried installing an unlocked firmware version, on the offchance that my carrier (AT&T) was doing something weird. This did not help either.
I have no idea where to go from here. I thought that a system reset is supposed to completely wipe everything from your phone, so that it behaves exactly how it did when I first got it. But that's not the case. It seems like something is carrying over that's causing this issue. Does anybody have any idea what I should do?

Do you have lock instantly with power key on?

funkyverb said:
This issue has been driving me mad for the past couple weeks. I'm at my wits' end and I need some expert help to figure this out. Please read this post thoroughly to understand my situation, as this is not a simple matter of uninstalling some apps.
When I first got my Note 9, the screen lock button worked perfectly. The screen would immediately turn on when I pressed the button, and it would immediately turn off when I pressed it again. However, once I got the Android Pie update, the screen lock button stopped working properly. The screen still turns on immediately, but there's about a 0.5 second delay after I press the button to turn it off. It's a relatively small issue, but it's enough to bother me.
I attempted to fix this by performing a system reset. But this did not help. In fact, this issue is still present even before completing initial setup of the phone.
When you perform a system reset, the first screen you see when your phone restarts is the welcome screen. It contains a "start" button that you press to begin setup. On this screen, the lock button issue does not happen. My phone locks and unlocks correctly. On the next screen, you connect to a wifi network. After connecting to a wifi network, the lock button issue becomes present. In other words, this issue with the lock button is present before I even start using the OS, or install any apps, or really do anything at all. It seems to be triggered by connecting to a wifi network during setup.
So I figured there must be something wrong with the firmware. So I used Odin to flash an earlier firmware version. This did not solve the issue. I even tried installing an unlocked firmware version, on the offchance that my carrier (AT&T) was doing something weird. This did not help either.
I have no idea where to go from here. I thought that a system reset is supposed to completely wipe everything from your phone, so that it behaves exactly how it did when I first got it. But that's not the case. It seems like something is carrying over that's causing this issue. Does anybody have any idea what I should do?
Click to expand...
Click to collapse
It is probably the double tap power button to open camera feature. You can toggle it off and locking will be instant.
If its already off, there my be an accessibility service listening key presses.

xantrk said:
It is probably the double tap power button to open camera feature. You can toggle it off and locking will be instant.
If its already off, there my be an accessibility service listening key presses.
Click to expand...
Click to collapse
Oh my god, that fixed it... Can't believe I spent so much time trying to diagnose this. Thanks!

funkyverb said:
Oh my god, that fixed it... Can't believe I spent so much time trying to diagnose this. Thanks!
Click to expand...
Click to collapse
This delay issue is so silly but it annoys the hell out of me. Where did you turn off this feature in Pie?
Update: Found it. Just use the search box in settings and type in "camera" (or whatever it is in your language). The "double tap power" setting will get listed.
Thanks alot,
Watz

I even turned off the double press for camera app but I'm still noticing a 0.5 sec lag when i press the side key
I even restarted after changing the setting
Nothing is happening
Please help

xantrk said:
It is probably the double tap power button to open camera feature. You can toggle it off and locking will be instant.
If its already off, there my be an accessibility service listening key presses.
Click to expand...
Click to collapse
Thank you bro.