Hello.
Recently my phone got stuck so i decided to reboot it, after reboot theres just a logo screen.
Recovery mode doesnt work.
Charging works (but after yesterday's manipulations charging logo is turning on but seem to be stuck either (though i guess its working just not animated anymore)).
Download mode works.
My OS was Cyanogen (i dont remember version).
I am kinda newbie but i ve read some stuff on the intenet and tried to solve the problem with Odin. I used N7000XXLSZ_N7000OXELS7_N7000XXLSO_FACTORY_SER with Odin versions: 1.83, 1.85 and 1.87 with
boxes checked PDA, PHONE, CSS.
1. Odin 1.85 is getting stuck on "NAND Write Start".
<ID:0/003> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> CODE_N7000XXLSZ_906407_REV02_user_low_ship.tar.md5 is valid.
<OSM> MODEM_N7000XXLSO_REV_05_CL1240075.tar.md5 is valid.
<OSM> CSC_OXE_N7000OXELS7_975051_REV00_user_low_ship.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> zImage
<ID:0/003> NAND Write Start!!
2. Odin 1.83 is getting stuck on "zImage".
<ID:0/003> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> CODE_N7000XXLSZ_906407_REV02_user_low_ship.tar.md5 is valid.
<OSM> MODEM_N7000XXLSO_REV_05_CL1240075.tar.md5 is valid.
<OSM> CSC_OXE_N7000OXELS7_975051_REV00_user_low_ship.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> zImage
3. Odin 1.87 is getting stuck on "NAND Write Start".
<ID:0/003> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> CODE_N7000XXLSZ_906407_REV02_user_low_ship.tar.md5 is valid.
<OSM> MODEM_N7000XXLSO_REV_05_CL1240075.tar.md5 is valid.
<OSM> CSC_OXE_N7000OXELS7_975051_REV00_user_low_ship.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> zImage
<ID:0/003> NAND Write Start!!
I ve tried about 5+ times with each version.
You are my last hope fellas
Try just flashing an Odin version of philZ kernel. Also try another laptop with freshly installed samsung USB drivers.
Flash PhilZ kernel from Odin 3.07. After this, you'll have working PhilZ Touch Recovery
Try flashing philz cwm as they said or try flashing a stock ROM from sammobile.com .. And only use PDA and untick auto reboot ..
Related
I try to update my android software back to froyo (2.2) using the ezbase, but the installiation freezes at:
<ID:0/004> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> EZbase-PDA-XWJS3.tar.md5 is valid.
<OSM> EZbase-PHONE-XXJVE.tar.md5 is valid.
<OSM> EZbase-CSC-XXJV1.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/004> Odin v.3 engine (ID:4)..
<ID:0/004> File analysis..
<ID:0/004> SetupConnection..
<ID:0/004> Initialzation..
<ID:0/004> Set PIT file..
<ID:0/004> DO NOT TURN OFF TARGET!!
whta i´m gonna do now??
huuuh, i already got it
lmao, just fyi, what I did last time that happened to me was to just pull the cable out, restart back to download mode, and things should be working like normal
Hi All,
I have a Chinese version of the Note GT-19220, It has ICS on it but is missing Google Play so have tried to flash a new western version of ICS using Odin PC
I have followed the instructions exactly as described and I get a fail almost at the end of the process.
Now I get a picture of a phone and a yellow triangle and a monitor and below it is says Software Update failed.
The message I see in Odin is:
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> N7000XXLQ3_N7000XXLPT_N7000NEELP4_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/006> Odin v.3 engine (ID:6)..
<ID:0/006> File analysis..
<ID:0/006> SetupConnection..
<OSM> All threads completed. (succeed 0 / failed 1)
<ID:0/006> Removed!!
<ID:0/006> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> N7000XXLQ3_N7000XXLPT_N7000NEELP4_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/006> Odin v.3 engine (ID:6)..
<ID:0/006> File analysis..
<ID:0/006> SetupConnection..
<ID:0/006> Initialzation..
<ID:0/006> Get PIT for mapping..
<ID:0/006> Firmware update start..
<ID:0/006> cache.img
<ID:0/006> NAND Write Start!!
<ID:0/006> factoryfs.img
<ID:0/006> hidden.img
<ID:0/006> modem.bin
<ID:0/006>
<ID:0/006> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
Does anyone know how I can fix this? I have tried with several roms with the same result.
Do I need to take it to Samsung now to be fixed?
Sliderse said:
Hi All,
I have a Chinese version of the Note GT-19220, It has ICS on it but is missing Google Play so have tried to flash a new western version of ICS using Odin PC
I have followed the instructions exactly as described and I get a fail almost at the end of the process.
Now I get a picture of a phone and a yellow triangle and a monitor and below it is says Software Update failed.
The message I see in Odin is:
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> N7000XXLQ3_N7000XXLPT_N7000NEELP4_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/006> Odin v.3 engine (ID:6)..
<ID:0/006> File analysis..
<ID:0/006> SetupConnection..
<OSM> All threads completed. (succeed 0 / failed 1)
<ID:0/006> Removed!!
<ID:0/006> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> N7000XXLQ3_N7000XXLPT_N7000NEELP4_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/006> Odin v.3 engine (ID:6)..
<ID:0/006> File analysis..
<ID:0/006> SetupConnection..
<ID:0/006> Initialzation..
<ID:0/006> Get PIT for mapping..
<ID:0/006> Firmware update start..
<ID:0/006> cache.img
<ID:0/006> NAND Write Start!!
<ID:0/006> factoryfs.img
<ID:0/006> hidden.img
<ID:0/006> modem.bin
<ID:0/006>
<ID:0/006> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
Does anyone know how I can fix this? I have tried with several roms with the same result.
Do I need to take it to Samsung now to be fixed?
Click to expand...
Click to collapse
Have you tried flashing stock rom of the Chinese version of the Note GT-19220?
Since you have the chine i9220 then make sure you get the specific roms for the chinese version. If you try flashing the N7000 roms you may get this error or may brick it so just be careful.
Sliderse said:
Hi All,
I have a Chinese version of the Note GT-19220, It has ICS on it but is missing Google Play so have tried to flash a new western version of ICS using Odin PC
I have followed the instructions exactly as described and I get a fail almost at the end of the process.
Now I get a picture of a phone and a yellow triangle and a monitor and below it is says Software Update failed.
The message I see in Odin is:
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> N7000XXLQ3_N7000XXLPT_N7000NEELP4_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/006> Odin v.3 engine (ID:6)..
<ID:0/006> File analysis..
<ID:0/006> SetupConnection..
<OSM> All threads completed. (succeed 0 / failed 1)
<ID:0/006> Removed!!
<ID:0/006> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> N7000XXLQ3_N7000XXLPT_N7000NEELP4_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/006> Odin v.3 engine (ID:6)..
<ID:0/006> File analysis..
<ID:0/006> SetupConnection..
<ID:0/006> Initialzation..
<ID:0/006> Get PIT for mapping..
<ID:0/006> Firmware update start..
<ID:0/006> cache.img
<ID:0/006> NAND Write Start!!
<ID:0/006> factoryfs.img
<ID:0/006> hidden.img
<ID:0/006> modem.bin
<ID:0/006>
<ID:0/006> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
Does anyone know how I can fix this? I have tried with several roms with the same result.
Do I need to take it to Samsung now to be fixed?
Click to expand...
Click to collapse
You flashed N7000XXLQ3_N7000XXLPT_N7000NEELP4
It was N7000's rom and i feel its not compatible for i9220
You can flashed lidroid rom, both i9220 and n7000 can be flashed, I tried it and it works
Sent from my GT-N7000 using xda premium
hi all MyFriends
pls help meee
my samsung SIII does not start, it just displays a white screen.
when I formatted with Odin there has the famous error message "There is no PIT partition ".
when I formatted with a pit file it gives me the error message:
<ID:0/003> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> CODE_I9300XXELLA_742798_REV00_user_low_ship.tar.md5 is valid.
<OSM> MODEM_I9300XXELLA_742798_REV00_user_low_ship.tar.md5 is valid.
<OSM> CSC_I9300OXAELLA_742798_KOR_FACTORY_user_low_ship.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Get PIT for mapping..
<ID:0/003>
<ID:0/003> There is no PIT partition.
<ID:0/003> Added!!
<OSM> All threads completed. (succeed 0 / failed 1)
why did you tick repartition in the first place? not much you can do now. don't screw around with pit files, they are a serious deal
Glebun said:
why did you tick repartition in the first place? not much you can do now. don't screw around with pit files, they are a serious deal
Click to expand...
Click to collapse
Seems he is right.
Model: G900A
Version: 4.4.4
Baseband: G900AUCU2AOA2
I'm trying to root my G900A via the instructions from muniz_ri thread. While flashing with Odin3 V3.10 I load G900A_ND3_Stock_Kernel into the AP and press start but freezes on boot.img forcing me to unplug and power off. Is it because its ND3 and not NG3. I found it weird that his kernels were in the S4 files and not the S5 files. Any ideas?
<ID:0/006> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> G900A_ND3_Stock_Kernel.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/006> Odin engine v(ID:3.1005)..
<ID:0/006> File analysis..
<ID:0/006> SetupConnection..
<ID:0/006> Initialzation..
<ID:0/006> Get PIT for mapping..
<ID:0/006> Firmware update start..
<ID:0/006> SingleDownload.
<ID:0/006> boot.img
I have a note 5 SM-N920C and it's rooted, I'm trying to flash the stock firmware but it won't work for some reason.
For odin version 3.09 I get this, I left it on for a hour but still the same thing.
I used N920CXXU1AOH2_N920COJV1AOH2_N920CXXU1AOH2_HOME.tar.md5 for flashing
<ID:0/005> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> N920CXXU1AOH2_N920COJV1AOH2_N920CXXU1AOH2_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/005> Odin v.3 engine (ID:5)..
<ID:0/005> File analysis..
<ID:0/005> SetupConnection..
<ID:0/005> Initialzation..
<ID:0/005> Get PIT for mapping..
<ID:0/005> Firmware update start..
<ID:0/005> SingleDownload.
<ID:0/005> sboot.bin
<ID:0/005> NAND Write Start!!
mhm,whats problem do you have exactly?,i cant see nothing in the log.
maybe you need the last odin version 3.11.1
Had the same issue while flashing auto-root via odin.
It just stays stuck at NAND write part.
Familiaaa said:
mhm,whats problem do you have exactly?,i cant see nothing in the log.
maybe you need the last odin version 3.11.1
Click to expand...
Click to collapse
The problem is that I can't install the stock firmware, it doesn't complete the installation for some reason. Also when I am in TWRP, it said that there isn't a OS installed and I have seen that I have to install stock firmware.
I did try odin 3.12.3 and it failed, then I tried odin 3.10.6, it failed but now it also stops at a certain point and won't complete the installation. I could try odin 3.11.1, thanks for response.
I just tried Odin 3.11.1, failed
<ID:0/005> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/005> Odin engine v(ID:3.1101)..
<ID:0/005> File analysis..
<ID:0/005> SetupConnection..
<ID:0/005> Initialzation..
<ID:0/005> Get PIT for mapping..
<ID:0/005> Firmware update start..
<ID:0/005> SingleDownload.
<ID:0/005> sboot.bin
<ID:0/005> NAND Write Start!!
<ID:0/005> cm.bin
<ID:0/005> FAIL!
<ID:0/005>
<ID:0/005> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
After that I tried odin 3.10 and 3.10.5, stuck again but at setupconnection
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> N920CXXU1AOH2_N920COJV1AOH2_N920CXXU1AOH2_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/005> Added!!
<ID:0/005> Odin v.3 engine (ID:5)..
<ID:0/005> File analysis..
<ID:0/005> SetupConnection..
I think the problem is my stock firmware, I can't seem to find the stock for a SM-N920CZDAXSG. Help plz
It was the stock firmware, wrong version, I cry today.