I was installing TWRP on my LG L90 D405. Then after reboot it failed to turn on the screen was just black. I thought bout changing the firmware. After formatting I accidentally removed the USB before a flashed any recovery. When I connected again the mass storage file manager didn't show, all I could see was Qualcomm HS-USB QDLoader 9008 on device manager.
Please help :crying::crying::crying:
Related
What I think happened is this, i wanted to format my interal storage manually. But instead the entire mmcblkp0 got formatted..
Now i cant boot anymore and pc recognizes it as qualcomm hs-usb qdloader 9008.
I tried to recover with QPST tool, but no luck.
Flashmode/fastboot not working. Phone doesnt even vibrate on longpressing vol up + power.
Does anyone know how this can be fixed?
pliiiz sam one help me :angel:
thanx
Hi,
please I was trying to downgrade from AW 2.0 to AW 1.5 But after I install TWRP recovery and try to install AW 1.5 image, my watch turn off. Even when I try long press crown button, nothing happens, screen is still off.
When I connect it to PC, in device manager I see Unknown device and error code 43 - Windows has stopped this device because it has reported problems
Please is there any way how to fix it?
Thanks a lot.
EDIT:
I shows that installed driver is - qhsusb_bulk - Qualcomm HS-USB QDLoader 9008
So it's look like hard-brick. Is there any way how to unbrick my watch?
Did you try any other USB ports? For some reason, Windows may give you that answer on a 2.0 USB port. Try a 3.0 or 3.1 USB port if you have one on your PC. If not, find someone who has it on their PC
pavlli said:
Hi,
please I was trying to downgrade from AW 2.0 to AW 1.5 But after I install TWRP recovery and try to install AW 1.5 image, my watch turn off. Even when I try long press crown button, nothing happens, screen is still off.
When I connect it to PC, in device manager I see Unknown device and error code 43 - Windows has stopped this device because it has reported problems
Please is there any way how to fix it?
Thanks a lot.
EDIT:
I shows that installed driver is - qhsusb_bulk - Qualcomm HS-USB QDLoader 9008
So it's look like hard-brick. Is there any way how to unbrick my watch?
Click to expand...
Click to collapse
can't you get it into fastboot bootloader mode then run the fastboot commands to apply the OTA?
https://www.youtube.com/watch?v=ZmBY9KM1NE8
Hello everyone.
Yesterday while i was trying to install a new rom in my MI5 I bricked my phone.
I wiped the system, data, cache and kernel cache, then, as a mistake I rebooted my phone and all of a sudden it turned black and I couldn't go to the recovery or fastboot.
Now the phone is just black, no response trying to boot or go to recovery\fastboot. When I put to charger theres no LED LIGHT.
So I installed the adb drivers, installed MiFlash, and the computer recognized the phone as QualComm HS-USB QDLoader 9008 COM4.
Then I installed a fastboot rom into the phone using MiFlash, it said flash done and successful.
But, it keeps freezed in a black screen.
Should I just wait for a miracle or theres another option?
My PC still recognizes the phone as QualComm HS USB QDLoader 9008 COM 4.
Thanks in advance.
// EDIT (SOLVED)
Ok so now it booted with the fastboot ROM I flashed.
As I see, after the flash it takes hours to boot. I just went home, dropped the phone in the bed, then I pressed Vol up+Vol down and power button at the same time for two minutes and worked.
My Zenfone 4 ZE554KL is bricked and only shows on windows Qualcomm HS-USB QDLoader 9008, after I tried to debrick it from fastboot, using a firmware raw image, and putting the incorrect fastboot reboot command
"fastboot reboot emergency" and now is after I plug the usb stick it shows on windows as the QComm Com port but I tried to see guides, read everything, tried to use QFIL to check if something works and QPST
But still without success
Current phone status is a black screen and nothing else, already attempted to hold power, some few sequences with Vol Up, Vol Down still nothing.
Hello, today I tried to install a custom rom on my xiaomi mi5x, after successful installation, my device did not restart. Power on does not turn on , plug in charger does not receive . When I connect to the computer it only receives " qualcomm hs-usb qdloader 900e " . I have tried many ways to unbrick but all are not working, after successful flashing, the device does not boot, has no signal, and connects to the computer only receiving HS-USB qdloader 900e