Hi,
I had a battery and ear speaker problem on my Xperia Z. I ordered the spare part and change them this morning. Everything went fine. The battery was a bit hard to take out.
I reassembled everything, boot and.. no screen Backlight is ok. I can hear the boot noise, but nothing no touch, no screen !
I try to reset, repair with Bridge on mac. Bridge said everything went fine but... no screen.
Any idea what's wrong ? A problem with the screen flex cable?
I can see some copper in some place (file attached)
It is not a software problem, just an hardware one. There could be two problems:
1. The flex cable above the battery is not properly inserted
2.The flex cable is damaged during the extraction of the battery.
Try this, remove the flex cable and blow some air on it and then try to put it back in and make sure it clicks
Thanks, already done that. I will try again. I hop it's not damaged due to the micro scratches
it clicks ... but still nothing
Related
Hi i have had an x1 since august but within a month its been dropped and then it was unable to show the screen, i opened my device to try and fix my problem but messed with nothing whatsoever, when i put everything back together it wouldnt even turn on anymore! all it did was charge and when it was fully charged there was a red light. can anyone help me? please im desperate to fix my phone. My first paycheck was spent on this and i loved it despite the numerous flaws! also i havent charged it in over 2 - 3 months. Also when i opened it the tape that connect the rear and the front is kind of messed up, would that effect anything?
The tape that connects the front and the rear is the cable for the screen, so if it's messed up, you might need to get a replacement.
here is a pic, the red part where its circled is where i think the problem is, it looks ripped off, i did have a hard time opening and putting it back together the first time also.
Sounds like (Or rather, looks like) you're screwed, as far as I can tell, if it's really ripped. Otherwise attempt to clean the contact points with some cleaning alcohol and Q-Tips - something might have made it's way in when you disassembled the unit and blocked the electrical signals.
ill try it, but if that doesnt work, would i be able to replace the flex ribbon? would acteone work?
got this checked out by my friend, he told me its the flex ribbon cable, thanks for the help btw. Does anyone know the cheapest place to get a flex ribbon cable from?
Still would like confirmation if its my flex ribbon cable before i spend 40 bucks on a new one. thanks!
Hi, I am new to this forum. Sorry for posting here but I think I have similar or same problem with my xperia. Few days ago I drooped my xperia and then I could not turn it ON. I opened unit, the flex cable was detached.
After attaching the flex cable. I could turn the unit and it booted normal but no response on touching screen I even tried to align it but it did not respond. I turned off the unit. After trying turning it back ON only back light of the screen turned on (no sony logo, no xperia logo no winmo).
I tried to turn it on few times but same result. Even tried to soft reset and hard reset it but no difference only back light. Is it because of flex cable or because some thing else? I can`t even go in to 3 color screen. Please help. Sorry for my bad eng. Thanks.
Hey
A friend of mine called me yesterday if I wanna buy his broken X1 (it felt down :/) and repair it, because I'm the man for such jobs
Do you think it's only the LCD-flex-cable or another repairable damage?
I think I can get that device for 2-3 days and then decide if I buy it...
Some ideas? Is there any chance to repair it?
Thanx, Carbon
yes, probably even a loose connector on flex cable
Hello,
I am quite certain it is an easy problem, i have seen many x1 phones with just a minor loose connector which causes the screen not to respond.
The best way to check it if it really is just the screen/flex cable is to turn it on, and check if the side lights flash in all colors.
If that works the phone should work normally. (even if the screen doesn't work)
After opening:
Re-insert all the cables in the screen flex cable and check if it works..
if that doesn't work then replace the flex cable.
If the screen works:
Then check out the screen if it has any crack's or black spots.
In that case you will have to replace the screen/touch screen also.
Generally, if there is no physical damage to the LCD itself and the phone buzzes on startup with all appropriate sounds - replace the flex. Flashing lights are attached to the flex and are positioned ABOVE the LCD on flex connection, therefore will not light up if the flex is damaged and neither will the upper keypad and other less obvious things.
The flex replacement is not minor, just be aware of that. Bad falls are also the reason for main PCB damage, in which case there will be nothing you can do.
Thank you so much
It was a "very short" call by this friend, but when i take the device, I want a precise report what happened...
atm I don't now if the sidelights show reaction, but I will report
I'm afraid of a real PCB damage...
In flex problem side lights will not light up, as i mentioned, they are positioned above the Lcd connection, so if the main flex connection ribbon is damaged, as is most often the case, all of the upper level functions will be gone, but you will get a startup with buzz and sounds present.
I got it
And LEDs are flashing and you can start it complete normally, but you see nothing... i'm going to open it and check the Flexcable
Carbon386 said:
I got it
And LEDs are flashing and you can start it complete normally, but you see nothing... i'm going to open it and check the Flexcable
Click to expand...
Click to collapse
Best of luck.
Hello, guys!
Recently I bought an HTC One with cracked digitizer, but functional. It had a lot of scratches etc, but this is not important right now. I wanted to do a complete make-over so I bought replacement parts from the internet, I bought the front housing with the LCD screen and the back cover. I dissasembled the phone from the old housing (the one with the broken digitizer), and I assembled it back on the new housing. After all of that, I powered on the phone and it worked like a charm (the LCD and the touch-screen worked perfectly), but then I saw that the glass was a little out, I mean it was upper than the speakers cover, so I decided to take out the whole screen and to change the adhesive, because it was too loose and the screen wasn't staying properly. I succesfully did that, i put the screen back and everything was good, but when I wanted to start the phone, the screen remains black. And this is the problem I have. I mention that I worked very carefully with the screen, so I don't think the problem is at the screen. I disconnected and reconnected all the cables and still doesn't work. When I press the power button it vibrates and then it's making that sound like the phone is booting, but no image on the LCD. If I keep the power button pressed, the back and home buttons are blinking and then the same story as before, vibrates and then the sound. I really don't know what could be the problem.
I really need some help with this and I'm open to all of your suggestions. If you want more informations feel free to ask.
Thanks in anticipation!
To me it looks like you damaged one the flat flex cable.
When you took the screen out did it come like suddenly and maybe some tension was applied to the flat flex?
If I were you I would take it apart and verify the connection in the socket, maybe the socket was damaged or something and it doesn't make a good connection
I hope it works out for you
Thank you for your answer!
When I took out the screen, I took it out very carefully and there wasn't any tension applied to the flex cable, so I don't think this is the problem. I think it's more likely a problem with the socket on the motherboard, like you said, and it's not making a good contact. But what can I do about that?
Hi all,
Last weekend I tried to fix the GPS on my Xperia Z (C6603) - it couldn't lock any satellite and according to all tests it was a hardware problem. When I opened the back cover I saw that the GPS antenna wasn't securely attached anymore (thanks to the third party who replaced my screen last summer I guess). While I was at it, I also wanted to check the speaker since the volume is generally quite low. Doing so I had some difficulty getting the battery out but it didn't look like anything was damaged by it.
I fixed the GPS antenna and reassembled the phone, but now it won't boot anymore...
When I try to boot it the LED blinks red three times and then stops. Nothing more. It only seldomly responds to a cold reset (vol up + power for 10 sec.) but mostly not. When I connect it to the wall socket or laptop the LED burns red continuously.
When I opened the phone I still had about 70% battery left so that should be fine. Nevertheless I've had it on a charger overnight (LED continuously red) and tried the next morning without success.
What I have found is that the red LED indicates either a broken bootloader or a hardware fault. Since it occurred after I opened the phone I would assume the latter.
I have managed to do a repair through the PC Companion software but without result. I can still get the phone in fastboot (LED turns blue) connected to my laptop to flash. The screen doesn't turn on, though I'm not sure if it should? I'm also not sure if being able to connect in fastboot excludes hardware failure?
I haven't tried to root/flash because I first want to ask for some advice on a more systematic approach to fixing it. Also, tonight I will pick up a friend's Xperia Z with a broken screen for spare parts (same model, he got it one month later). So except for the screen I have working replacement parts. Besides the screen replacement (with original Sony parts) the phone was still in original state both in hard- and software.
I would really like to fix the phone since I liked it and I'm stuck to a SIM-only plan until December still. Third-party repair is out of the question because of costs; then I'd rather spend it on a new XZ5.
Any ideas on how I should approach this?
After some trial and error, I have managed to flash a stock ROM (.253) on it. No luck with that unfortunately. When I try to turn it on, there is a small vibration after a few seconds and that's it. Again the phone responds to a cold reset, but when I try to boot it after the LED blinks red three times again. That's all it does.
I would say the only thing to still try now is swapping the motherboard with the other phone, not? Or are there any other suggestions?
Well, I would assume that it is a hardware problem, especially taking in to the account that you touched components inside.
Even if we all know how phone work, and where are all components are, its not recommended to touch anything inside if you dont have steady hand and environment to make any repair(clean place, no humidity, clean hands).
One bad plugged connector can brick your phone. One time I even had problem on other phone with really small rust on one pin that I touched with finger(sweat from it+time+really crappy weather where I had to use it), so it show how actually fragile phones are.
But few questions, when you managed to flash rom, you get all that android logo when you are in flashmode, and it show everything(loading bar etc) on screen?
Im asking because first symptom of bad battery connection is deformed or totally dead screen.
When you fixed gps antenna(that black plastic on top near camera) you used any tool that could damage board? its near microUSB so its easy to mess those small pins and make short circuit.
The same with battery, you could try to squeeze/move it a bit to see if there is any changes in phone boot behavior(not to gentle way to check it but sometimes it show if there is a problem)
Before changing motherboard I would replace battery from your other phone(charged before that) and check all pins on connector and board near it if there is any problem.
But as I said it should be made really delicate and in appropriate conditions.
Sadly I cant really help with it beside that, and I hope your phone gonna stand up after that somehow :/
Thanks for the reply Akinaro. Indeed the conditions are not ideal. At least I have one of those repair tool kits with the small screwdrivers, plastic pick and plastic levers for the connectors. I'll also set a reminder to take some latex/nitril gloves from the lab for next time
But few questions, when you managed to flash rom, you get all that android logo when you are in flashmode, and it show everything(loading bar etc) on screen?
Im asking because first symptom of bad battery connection is deformed or totally dead screen.
Click to expand...
Click to collapse
No, the screen is totally dead. No sign of life whatsoever.
When you fixed gps antenna(that black plastic on top near camera) you used any tool that could damage board? its near microUSB so its easy to mess those small pins and make short circuit.
The same with battery, you could try to squeeze/move it a bit to see if there is any changes in phone boot behavior(not to gentle way to check it but sometimes it show if there is a problem)
Click to expand...
Click to collapse
Possibly. I have used both the screwdriver and the plastic tools, but fiddling everything back in was tricky. The battery was disconnected though so it shouldn't have short-circuited. I will try with moving around the battery. But the more I think of it, the more I start thinking that I screwed up the motherboard by touching something there.
Before changing motherboard I would replace battery from your other phone(charged before that) and check all pins on connector and board near it if there is any problem.
But as I said it should be made really delicate and in appropriate conditions.
Click to expand...
Click to collapse
I have tried the other battery last night as well. I didn't charge it first though, I left it in my phone to charge overnight and tried to boot it this morning, without result.
So I've attempted to swap the motherboards. Good and bad news...
The good news is that the spare phone works with every combination of motherboard and battery, so neither of those is the culprit. The bad news: none of the combinations work on my own phone, even with swapping all the other hardware components (camera's, gps, antenna etc.).
On the other hand, by now the LED doesn't turn red anymore. The phone just stays completely off. I didn't have time to try and charge it for some time though, so I'm not sure if it's a good or a bad sign.
I fear that the main multiconnector running under the battery might be damaged when I took out the battery and antenna module the first time. That is the only component that I cannot swap for it is so integrated - it would mean swapping the screen to the spare-parts-phone and using that one.
Any ideas still before I should consider it a write-off completely?
I've got a replacement screen that my friend had in his house. Mine was broken (both the display and the digitizer, the latter was acting very weird). I did the replacement myself, and when I was finally done, I noticed something. The Touch Screen wasn't working (I could see the image but no input was recognized). I tried opening it and checking every single cable to see if there was anything wrong, but there was nothing looking broken or out of place. When I was going to test it, I noticed another very weird thing. It actually works if I keep the back of the phone off (not the back interchangable cover, I mean the back of the phone that is screwed in place). The problem is that this phone has a very annoying design that makes it so the Wi-Fi, Speakers, Camera and some other stuff don't function well with the back plate off, speacially the Wi-Fi.
I trully have no idea what is happening or what is causing the problem with the touch screen, and have no idea why the back plate makes the screen act funny. Can someone please help me figure this out?
Perhaps something in the digitizer's flex cable is shorting with the back panel. Try putting a layer of electrical tape between the flex cable and the back panel.