Hi all,
Samsung Galaxy S3 - GT-I9305. After the OS patch was getting a few issues like system randomly resting, security block popups on some apps when there never was before. One night however woke up and the phone was powered down. Now only powers up only into Samsung Logo bootloop. Cant enter recovery mode, just goes into the loop. I've got 2 ROMs from SAM mobile for my carrier, one older and one recent, as i'm unsure what my ROM is and cant check it now. Both however fail with Odin. Log listing below.
Have tried different ports, using original cable. Ideally would like to get my data back as pictures and contacts were not backed up.... Please help! Pretty desperate and haven't really found anything in forums for this situation.
Odin logs;
<ID:0/006> Added!!
<OSM> Enter CS for MD5..
<OSM> Binary Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/006> Odin engine v(ID:3.1100)..
<ID:0/006> File analysis..
<ID:0/006> SetupConnection..
<ID:0/006> Initialzation..
<ID:0/006> Get PIT for mapping..
<ID:0/006> Firmware update start..
<ID:0/006> SingleDownload.
<ID:0/006> sboot.bin
<ID:0/006> NAND Write Start!!
<ID:0/006> FAIL!
<ID:0/006>
<ID:0/006> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
TWRP
Hello and thank you for using Q/A,
can you please try flashing TWRP via AP:
twrp-2.8.7.0-i9305.img.tar
And then please try to boot into TWRP using the known combination. Tell me, if your I9305 is booting into TWRP then.
Regards
Trafalgar Square
Thanks for reply. I tried on Odin3 1.87 and 3.10.7 both fail; log
<ID:0/006> Added!!
<ID:0/006> Odin engine v(ID:3.1100)..
<ID:0/006> File analysis..
<ID:0/006> SetupConnection..
<ID:0/006> Initialzation..
<ID:0/006> Get PIT for mapping..
<ID:0/006> Firmware update start..
<ID:0/006> SingleDownload.
<ID:0/006> recovery.img
<ID:0/006> NAND Write Start!!
<ID:0/006> FAIL!
<ID:0/006>
<ID:0/006> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
Option selected auto reboot via AP.
:crying:
Any other suggestions?
The thread is dead, but in case anyone is coming across the same sort of problem.. i bit the bullet and took it to a service tech. They couldn't fix it and had to replace the motherboard. So unfortunately that was the solution for me anyway. :crying:
Related
This is my first post, so I will try to be clear:
I have SGS I9000 2.3.3 rooted with Odin (CF-Root-XW_NEE_JVH-v3.2-CWM3RFS) and was working perfectly for the last weeks.
Today I tried to setup my work email on my phone with the built-in Email Client, and due to company policy I had to encrypt all the files on the phone( this is done automatically).
The issue started after it finished encrypting the files, the mobile didn't start again and got stuck at the logo page. I tried many times without success I also tried to go to the recovery mode but it's also stuck at Downloading page and it doesn't move (No menu).
how can I perform a factory reset? Is there any other solution
Thanks for ur answers
Your best off reflashing the firmware dude, via Odin
Sent from my CM7 modded I9000. Kernel is one mean son of a Glitch!
thanks for your recommendation.
I just tried to reflash it with the official load from Samsung and it failed, below the output of odin:
<ID:0/006> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> PDA_XWJVH_Sbl.tar.md5 is valid.
<OSM> PDA_XWJVH_Sbl.tar.md5 is valid.
<OSM> CSC_XEE_JV3.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/006> Odin v.3 engine (ID:6)..
<ID:0/006> File analysis..
<ID:0/006> SetupConnection..
<ID:0/006> Initialzation..
<ID:0/006> Set PIT file..
<ID:0/006> DO NOT TURN OFF TARGET!!
<ID:0/006> Get PIT for mapping..
<ID:0/006> Firmware update start..
<ID:0/006> param.lfs
<ID:0/006> zImage
<ID:0/006> boot.bin
<ID:0/006> Sbl.bin
<ID:0/006> factoryfs.rfs
<ID:0/006> dbdata.rfs
<ID:0/006> param.lfs
<ID:0/006> Transmission Complete..
<ID:0/006> Now Writing.. Please wait about 2 minutes
<ID:0/006> Receive Response form LOKE
<ID:0/006> zImage
<ID:0/006> Transmission Complete..
<ID:0/006> Now Writing.. Please wait about 2 minutes
<ID:0/006> Receive Response form LOKE
<ID:0/006> boot.bin
<ID:0/006> Transmission Complete..
<ID:0/006> Now Writing.. Please wait about 2 minutes
<ID:0/006> Receive Response form LOKE
<ID:0/006> Sbl.bin
<ID:0/006> Transmission Complete..
<ID:0/006> Now Writing.. Please wait about 2 minutes
<ID:0/006> Receive Response form LOKE
<ID:0/006> factoryfs.rfs
<ID:0/006> Transmission Complete..
<ID:0/006> Now Writing.. Please wait about 2 minutes
<ID:0/006>
<ID:0/006> Receive Response form LOKE
<ID:0/006> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
where did you download the files? try download the ones from Ramad thread
I downloaded the files from thd "forum Official firmwares for Samsung Galaxy S I9000 - Download" which comes from xda-developers
It works now , by using Odin v1.7 instead of v1.82 with the same 4 files
Hey guys need a little help here, i just bought a motherboard for my girlfriends s5, the old one seemed to overheated and died, yeah seriously. was just sitting on the bed.
I just spent $100 to get an AT&T Mobo, cracked open the phone and installed it. (The LCD is really thin, but to my suprise is really strong)
Stock Android 5.0 L, tried to to downgrade to 4.4.4, realize i cant now because of locked bootloader. trying to just restore back to Android 5 now.
Recovery mode presents " Firmware upgrade encountered an issue, Please select recovery mode in kies"
Download mode presents " SW Rev Check Fail : [aboot] fused > 4 Binary 3 "
I suppose this is because i flashed 4.4.2 in Odin the following
AP, CP, CSC
BL was NOT flashed!
Currently tried to find BL, AP, CP and CSC for 5.0 L, figure it would solve the problem
However my google-fuu leads me no awnsers, Closest thing i could find was.
theandroidsoul dot com /att-galaxy-s5-lollipop-update-odin-firmware-80652/
looks like it will flash 5.0 software, but.
My odin fails everytime i try, I have tried this on two computers, Windows 7 & 8
<ID:0/003> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> One Click Downloader Mode
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Set PIT file..
<ID:0/003> DO NOT TURN OFF TARGET!!
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> SingleDownload.
<ID:0/003> aboot.mbn
<ID:0/003> NAND Write Start!!
<ID:0/003>
<ID:0/003>
<ID:0/003>
<OSM> All threads completed. (succeed 0 / failed 1)
I really dont think its a driver issue., tried multiple cables.
Thanks
Hello!
Recently flashed Dr.Ketan ROM, with the TWRP recovery, Was working perfectly, up until it rebooted. Now, I get a message in the top left corner saying that 'custom binary blocked by FRP lock' and the phone shuts down. and I'm getting the same message even if I try to boot into recovery. I tried Flashing new ROM through odin, but I'm unable to do so, as I'm getting a message on phone saying 'sw rev check fail device 2 binary 1'. I'm pretty clueless and stuck. Please, Please help me out. I've spent hours and I'm still nowhere close to getting it back running. My model is SM-N920G.
This is the message I get on Odin.
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Added!!
<ID:0/003> Odin engine v(ID:3.1100)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Set PIT file..
<ID:0/003> DO NOT TURN OFF TARGET!!
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> SingleDownload.
<ID:0/003> sboot.bin
<ID:0/003> NAND Write Start!!
<ID:0/003> cm.bin
<ID:0/003> FAIL!
<ID:0/003>
<ID:0/003> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
Re download the stock rom. You needed to turn on oem unlock
Hello all, I have looked everywhere and no one seems to be having the same problem as I have here.
So here is the problem: My note 4 keeps going into recovery and is giving me a few messages.
1) In the stock Android recovery that it boots into, on the bottom it displays "dm-verity verification failed..."
2) When clicking on "apply update from external storage", it gives me "Update from external storage is disabled"
Background:
In a previous post, I was trying to install Xposed framework and had an issue where it would not install. A friendly user suggested I install a different APK and flash a zip file through TWRP. I then installed TWRP through a play store app and booted into it. I installed the zip file, wiped data (including Dalvik) and the problem started.
So I tried flashing original N910T Rom through Odin and this is the log I got
BTW I am still able to access TWRP through holding Volume Up:Homeower but when phone boots up it goes into Android Recovery mode automatically, no bootloop. I tried clearing Data but that didnt help. Should I clear "System" through TWRP and reflash?
<ID:0/006> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> N910TUVU1ANIH_N910TTMB1ANIH_N910TUVU1ANIH_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/006> Odin engine v(ID:3.1005)..
<ID:0/006> File analysis..
<ID:0/006> SetupConnection..
<ID:0/006> Initialzation..
<ID:0/006> Get PIT for mapping..
<ID:0/006> Firmware update start..
<ID:0/006> SingleDownload.
<ID:0/006> aboot.mbn
<ID:0/006> NAND Write Start!!
<ID:0/006> sbl1.mbn
<ID:0/006> rpm.mbn
<ID:0/006> FAIL! (Auth)
<ID:0/006>
<ID:0/006> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
Superdudekk said:
So I tried flashing original N910T Rom through Odin and this is the log I got
BTW I am still able to access TWRP through holding Volume Up:Homeower but when phone boots up it goes into Android Recovery mode automatically, no bootloop. I tried clearing Data but that didnt help. Should I clear "System" through TWRP and reflash?
<ID:0/006> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> N910TUVU1ANIH_N910TTMB1ANIH_N910TUVU1ANIH_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/006> Odin engine v(ID:3.1005)..
<ID:0/006> File analysis..
<ID:0/006> SetupConnection..
<ID:0/006> Initialzation..
<ID:0/006> Get PIT for mapping..
<ID:0/006> Firmware update start..
<ID:0/006> SingleDownload.
<ID:0/006> aboot.mbn
<ID:0/006> NAND Write Start!!
<ID:0/006> sbl1.mbn
<ID:0/006> rpm.mbn
<ID:0/006> FAIL! (Auth)
<ID:0/006>
<ID:0/006> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
Click to expand...
Click to collapse
you may need this
http://forum.xda-developers.com/not...f-g-c-t-w8-t3282641/post64569392#post64569392
Unfortunately I tried that but I found a solution! A helpful youtube video showed that with these new Samsung Phones, you can connect to Kie3 or Smart Switch and click "Emergency Software Recovery and Initialization", enter your model and serial number and the program will automatically wipe and flash OEM Samsung ROM onto the phone. Only bad thing is that you have to re-root the phone. Great solution for soft bricks.
I have a sprint galaxy note 5. I accidently formatted in twrp. Since then its' stuck here ( NOTE: I WAS ON 5.1.1 AND I'M TRYING TO FLASH 6.0.1 I HAVE THE 6.0 TWRP THAT IS REQUIRED)
<ID:0/003> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> N920PVPU2BPD2_N920PSPT2BPD2_N920PVPU2BPD2_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Odin engine v(ID:3.1005)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
<ID:0/003> Removed!!
<ID:0/003> Added!!
<ID:0/003> Odin engine v(ID:3.1005)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> SingleDownload.
<ID:0/003> sboot.bin
<ID:0/003> NAND Write Start!!
<ID:0/003> cm.bin
<ID:0/003> boot.img
<ID:0/003> recovery.img
<ID:0/003> system.img
Click to expand...
Click to collapse
Anyone have any ideas at all? I have no way to get a replacement until next week so I'm gonna do what I can to get this working. Any additional info can be provided
what I've tried:
different ROM ( could be using the wrong one)
N920PVPU2BPC3_N920PSPT2BPC3_N920PVPU2BPC3_HOME.tar.md5
N920PVPU2BPD2_N920PSPT2BPD2_N920PVPU2BPD2_HOME.tar.md5
ALL_SPT_N920PVPU2BPC3_N920PSPT2BPC3_CL7231607_QB8832851_REV00_user_low_ship.tar.md5
all of these have the same problem. I am starting with a clean phone pretty much. system 0 bytes data 0 bytes
I have noticed that /system won't mount in TWRP when trying to repair the directory possibly this has something to do with it
Any advice at all is welcome. I have no clue where to go from here
EDIT: Just tried a new usb port and it worked after 7 hours of trying over and over
I would try to get my hands on an updated stock rom bundled with boot image and kernel and try that with odin. Also be sure you are using the right Odin.