After flashing custom recovery using "Infinix flash tool" the device does not charge beyond 88%
When I booted the phone, date and time got reset and battery problem appeared.
It goes to this percent then stop charging.
I tried to calibrate battery, but it doesn't help.
I flashed full firmware using flashtool but still the same problem.
Anybody knows a solution?
@Bolumstar did you find a workaround for this?
@Hovatek Do you know about this issue?
Mysteryagr said:
@Hovatek Do you know about this issue?
Click to expand...
Click to collapse
Yes, its similar to the 3% issue on the Tecno G9.
which firmware did you flash?
Hovatek said:
Yes, its similar to the 3% issue on the Tecno G9.
which firmware did you flash?
Click to expand...
Click to collapse
I was on marshmallow 305 update
Then I flashed custom recovery and battery problem appeared.
@Hovatek any solution?
If I flashed another rom while battery reading be fixed?
The phone takes nearly 3 hours to fully charge
Mysteryagr said:
@Hovatek any solution?
If I flashed another rom while battery reading be fixed?
Click to expand...
Click to collapse
Yes, it should be fixed. We have a Hot 2 among our collection and have encountered such.
Try reverting to Lollipop using firmware upgrade in SP flash tool
Hovatek said:
Yes, it should be fixed. We have a Hot 2 among our collection and have encountered such.
Try reverting to Lollipop using firmware upgrade in SP flash tool
Click to expand...
Click to collapse
Thanks, already fixed by doing so
Using infinix flashtool, sp flashtool doesn't work
Related
hi guys,i have a huge problem with my moto milestone,here it is :
i tried to flash it with cm7 with open recovery and something didn't work and got this error : "bootloader battery low,cannot program"
so i googled this error and got a fix for it with "mcguyver battery recovery"
(http://forum.xda-developers.com/showthread.php?t=892026)
the battery went back and i proceeded installing cm7,everything went fine,cm7 is awesome BUT i got this question mark on the battery,and the phone is not charging.
now,i cannot see what the problem is,i measured with the multimeter the following things :
1. the battery has 3.7v of juice in it right now
2. the contacts for charging the phone also have 5v when the phone is plugged in,so the basically the phone should charge the battery but it dosen't.
i'm thinking there is a problem reading the battery's status,i cannot figure it out.
if any of you have any solutions,please help me.
Flash an original 2.2 SBF using RSDlite and then re-flash CM7. That happened to me and that's what I only did.
pac213 said:
Flash an original 2.2 SBF using RSDlite and then re-flash CM7. That happened to me and that's what I only did.
Click to expand...
Click to collapse
i flashed the original 2.1 rom and it didn' work,i'll give it a try with 2.2 and will let you know,thanx in advance
pac213 said:
Flash an original 2.2 SBF using RSDlite and then re-flash CM7. That happened to me and that's what I only did.
Click to expand...
Click to collapse
any ideea where i could find a 2.2 sbf file ?
this is the list of sbf files i found and there is no 2.2...
freddy8teen said:
any ideea where i could find a 2.2 sbf file ?
this is the list of sbf files i found and there is no 2.2...
Click to expand...
Click to collapse
http://www.and-developers.com/sbf:milestone221
Sent from my Milestone using Tapatalk
sileshn said:
http://www.and-developers.com/sbf:milestone221
Sent from my Milestone using Tapatalk
Click to expand...
Click to collapse
i tried this too,everything worked fine but now it seems like it's got into a bootloop...it goes like this moto logo > android logo > unlock screen > reboot..
it stays open for 5-10 seconds and than it reboots itself..
Hi all,
i got a problem with my bluetooth phonebook sync. My phone connects via blutooth to the car, but the phone book does not sync. The request for the transfer of the phone book does not appear at all.
I have this Problem with following ROMs:
Sony Stock 4.3 (14.2.A.0.290)
IHackers 2.1 (JellyBean 4.3)
SlimKat 4.4
However, no problems with these ROMs,
Sony Stock 4.2.2 (14.1.G.2.257)
FreeXperia CM11 (fxp / kali)
What can cause this and how can I solve this problem for the other roms?
Thank you
Sony xperia Z1 C6903
Opel UHP car kit
You can flash the "Baseband" only from 14.1.G.2.257 on 14.2.A.0.290 or Update to .136. If .136 will not solve this problem then flash Baseband here too from .257.
I have the same problems with 290 and 136.. Does this mean that I can flash the 136 generic BALL ftf and then just flash the baseband from 257? It won't screw the phone up will it?
Regards,
Alan
nalab1 said:
It won't screw the phone up will it?
Click to expand...
Click to collapse
I can't guarantee that but this was confirmed by users who did that to improve the signals on they phone. They flashed baseband from 4.2.2 FW .257 on 4.3 FW .290 and it worked. Flashing anything its a risk so be careful, BTW, if this will not work you can flash the baseband from 4.3 FW .136 back, in the same way. If I am not wrong, if so someone correct me please, the baseband contain all package of frequency for the phone to work properly.
eclyptos said:
I can't guarantee that but this was confirmed by users who did that to improve the signals on they phone. They flashed baseband from 4.2.2 FW .257 on 4.3 FW .290 and it worked. Flashing anything its a risk so be careful, BTW, if this will not work you can flash the baseband from 4.3 FW .136 back, in the same way. If I am not wrong, if so someone correct me please, the baseband contain all package of frequency for the phone to work properly.
Click to expand...
Click to collapse
Hi eclyptos,
Thank you for your reply.. So, does the baseband contain all of the wireless stuff like wifi, bluetooth etc?
To get the sequence right I -
1) Completely flash .136 - reboot to check if ok
2) Flash the baseband ONLY from .257 - reboot to check if ok
If, the phone were to get stuck in say, a bootloop is there any way to completely power it off and then reflash?
Regards,
Alan
nalab1 said:
Hi eclyptos,
Thank you for your reply.. So, does the baseband contain all of the wireless stuff like wifi, bluetooth etc?
Click to expand...
Click to collapse
It should.
nalab1 said:
To get the sequence right I -
1) Completely flash .136 - reboot to check if ok
2) Flash the baseband ONLY from .257 - reboot to check if ok
Click to expand...
Click to collapse
Yes.
nalab1 said:
If, the phone were to get stuck in say, a bootloop is there any way to completely power it off and then reflash?
Regards,
Alan
Click to expand...
Click to collapse
Of curse but it will not stuck.
@chunlianghere already did this HERE and will report leater.
eclyptos said:
It should.
Yes.
Of curse but it will not stuck.
@chunlianghere already did this HERE and will report leater.
Click to expand...
Click to collapse
Hi eclyptos,
Thank you. For my information (sorry for the noobness!) if it were stuck in a bootloop how do I actually power the phone off?
Regards,
Alan
nalab1 said:
Thank you. For my information (sorry for the noobness!) if it were stuck in a bootloop how do I actually power the phone off?
Click to expand...
Click to collapse
Power + Volume Up. BTW, Flash with fully charged battery.
eclyptos said:
Power + Volume Up. BTW, Flash with fully charged battery.
Click to expand...
Click to collapse
Hi eclyptos,
Thank you for your replies and help. I am going to try this at the weekend as during the week, I work away from home and dont have access to my pc. I will let you know how it goes.
Regards,
Alan
eclyptos said:
You can flash the "Baseband" only from 14.1.G.2.257 on 14.2.A.0.290 or Update to .136. If .136 will not solve this problem then flash Baseband here too from .257.
Click to expand...
Click to collapse
I have tried this, but i did not work.
Any other advise?
Yocto69 said:
I have tried this, but i did not work.
Any other advise?
Click to expand...
Click to collapse
Are you saying that after flashing baseband from .257 on .136 you still have problems? Try downgrade the entire system and check if the problem persist. Sometime is not the phone but the other devices so really we can try looking forever.
eclyptos said:
Are you saying that after flashing baseband from .257 on .136 you still have problems? Try downgrade the entire system and check if the problem persist. Sometime is not the phone but the other devices so really we can try looking forever.
Click to expand...
Click to collapse
Look in the op. I have tried several Firmwares and Roms.
If i downgrade to. 257 It works perfect!
The other Device is not the problem.
Thx
Yocto69 said:
Look in the op. I have tried several Firmwares and Roms.
If i downgrade to. 257 It works perfect!
The other Device is not the problem.
Thx
Click to expand...
Click to collapse
Other than that can be a kernel.
eclyptos said:
Other than that can be a kernel.
Click to expand...
Click to collapse
Is it maybe possible to take a blutooth.apk from .257 and use it on .290?
Yocto69 said:
I have tried this, but i did not work.
Any other advise?
Click to expand...
Click to collapse
it works fine when listening music.
but during voice call, its not ok.
Yocto69 said:
Is it maybe possible to take a blutooth.apk from .257 and use it on .290?
Click to expand...
Click to collapse
Is not that easy. Bluetooth is not an application which you can download or install. It's implemented in the system and baseband. The main reason for bad quality like WiFi, Mobile Signal or Bluetooth is the Radio which is the Baseband in Z1. On HTC for example to improve the reception for all of them I am able to flash just the Radio.
eclyptos said:
Is not that easy. Bluetooth is not an application which you can download or install. It's implemented in the system and baseband. The main reason for bad quality like WiFi, Mobile Signal or Bluetooth is the Radio which is the Baseband in Z1. On HTC for example to improve the reception for all of them I am able to flash just the Radio.
Click to expand...
Click to collapse
Ok, i have tried severall kernel.
ihackers advanced kernel, stock kernel and doomlords kernel. All on 4.3 roms. => No change.
What else could I try?
Yocto69 said:
Ok, i have tried severall kernel.
ihackers advanced kernel, stock kernel and doomlords kernel. All on 4.3 roms. => No change.
What else could I try?
Click to expand...
Click to collapse
I losing ideas, I don't want to say but at last it may be a hardware issue but not sure. I don't know if you want to do this but you should go back to Stock and Flash a Stock FTF to check if the problem persist even there, is it does it's the phone.
Hi Experts,
I have searched the forum and after flashing for three sleepless nights, I am still struck with the unknown baseband issue.
The details are:
C6903
BL Unlocked & now its locked using Flashtool (DRM or TA backup is unavailable )
Currently the phone is struck in boot loop in .534
Used Flashtool ver. 0.9.22.3 & 0.9.18.6
Latest EMMA & Xperia Companion
My phone hanged when listening to the music and when I force restarted the unknown baseband showed up. While flashing I got the baseband back after flashing .518 however it hanged again after two days and I lost the BB
Now I am struck in boot loops on .534 and .518 both. I can boot into .290 successfully. Can someone please guide me to the correct method of restoring my IMEI permanently.
P.S. As per my short experience with C6903, I believe something stops the boot of .534 and .518 after first boot. Means I was not able to boot into .534 but accidentally when I flashed .518, my phone booted successfully. However now I am unable to boot into .518. May be I am missing the piece of puzzle that an expert can provide.
Thanks in advance~
D-r-e-a-m-e-r said:
Hi Experts,
I have searched the forum and after flashing for three sleepless nights, I am still struck with the unknown baseband issue.
The details are:
C6903
BL Unlocked & now its locked using Flashtool (DRM or TA backup is unavailable )
Currently the phone is struck in boot loop in .534
Used Flashtool ver. 0.9.22.3 & 0.9.18.6
Latest EMMA & Xperia Companion
Thanks in advance~
Click to expand...
Click to collapse
hi , read here and try reflash use [NUT]'s 14.1.G.1.534 FTF , hope its help.
iedafarha said:
hi , read here and try reflash use [NUT]'s 14.1.G.1.534 FTF , hope its help.
Click to expand...
Click to collapse
Thanks for your tip but I have already tried and still get struck in bootloop.
No .534 FTF has booted until now and I have used 6 of them already...
An update is that I have rooted 4.4.4 and installed recovery...
can someone tell me where can I get .534 zip to flash as the files I have are giving me verification error on TWRP.
Thanks in advance...
I have tried to use NUT fix but the files are not available for downloading.
I would really appreciate if someone can direct me to the correct path. I am almost giving up now...
http://forum.xda-developers.com/showthread.php?t=2687443
D-r-e-a-m-e-r said:
I have tried to use NUT fix but the files are not available for downloading.
I would really appreciate if someone can direct me to the correct path. I am almost giving up now...
http://forum.xda-developers.com/showthread.php?t=2687443
Click to expand...
Click to collapse
May be file deleted , other options you can create flash zip using PRFCreator , search and download ftf file from here .
iedafarha said:
May be file deleted , other options you can create flash zip using PRFCreator , search and download ftf file from here .
Click to expand...
Click to collapse
Hi again, Really appreciate your help.
I have tried flashing a number of files but still in vain. What I really can't understand is .518 was the last 4.2.2 rom that booted successfully on my phone and brought my baseband back. Now .534 and .518 are both ending in a bootloop at Sony animation Really driving me crazy...
As a side note, can you tell me if the modem files in the link below are useful for this issue?
https://github.com/SonyAosp/vendor_qcom_firmware/tree/n/honami/C6903
By the way I am really amazed with the Z1 ability to handle abuse that I have thrown at it during the last 2 weeks
Changing phone is not an option for me right now. Using Nokia 1100 after a long time seems very uncomfortable and can't do it for long
D-r-e-a-m-e-r said:
By the way I am really amazed with the Z1 ability to handle abuse that I have thrown at it during the last 2 weeks
Changing phone is not an option for me right now. Using Nokia 1100 after a long time seems very uncomfortable and can't do it for long
Click to expand...
Click to collapse
Anyone please...
Experts plzzz...
D-r-e-a-m-e-r said:
Experts plzzz...
Click to expand...
Click to collapse
I am still looking for a solution to install JB without bootloop
Bump...
D-r-e-a-m-e-r said:
I am still looking for a solution to install JB without bootloop
Click to expand...
Click to collapse
Lol why jb. Don't you want KitKat lollipop??
Heck even nougat with unlocked bootloader
gauravbhakuni90 said:
Lol why jb. Don't you want KitKat lollipop??
Heck even nougat with unlocked bootloader
Click to expand...
Click to collapse
I need to fix my baseband issue. That can only be done with JB.
D-r-e-a-m-e-r said:
I need to fix my baseband issue. That can only be done with JB.
Click to expand...
Click to collapse
You can flash Baseband even from lollipop ftf.
gauravbhakuni90 said:
You can flash Baseband even from lollipop ftf.
Click to expand...
Click to collapse
Thx for the tip but its not working.
My SIm was only detected once thats when I installed .518 but it lasted for a day and got held. When I force restarted the phone it was again missing baseband.
Now it isnt booting into .518 or .534.
Experts am I asking something that is un-do-able...
Guys shall I give up fixing this phone
I loved this dead beauty...
Hi, tried to flash with different cables as I don't have Sony original cable with me but the results are still the same. No luck with .534 and baseband is still unknown...
I understand this is a free community and people are free to determine if they wanna help someone or not. However I just wanna know if this is repairable or shall I just forget about repairing it. Any inputs will be highly appreciated.
D-r-e-a-m-e-r said:
Hi, tried to flash with different cables as I don't have Sony original cable with me but the results are still the same. No luck with .534 and baseband is still unknown...
I understand this is a free community and people are free to determine if they wanna help someone or not. However I just wanna know if this is repairable or shall I just forget about repairing it. Any inputs will be highly appreciated.
Click to expand...
Click to collapse
I have realized that the phone does not shuts down with the power button in any bootable rom. Also sometimes the baseband does appear soon after installation but it disappears as sim is inserted. Can someone plz help me understand whats going wrong. I really love this phone...
I flashed a custom firmware as I was rooting my phone using this guide http://forum.xda-developers.com/z3-compact/general/how-to-root-backup-drm-keys-t3013343
Now my touchscreen is totally unresponsive.
I tried reflashing to a stock firmware and it still doesn't work.
bluegreybolt said:
I flashed a custom firmware
Click to expand...
Click to collapse
Which custom firmware exactly? And what exactly did you use to flash it?
bluegreybolt said:
as I was rooting my phone using this guide http://forum.xda-developers.com/z3-compact/general/how-to-root-backup-drm-keys-t3013343
Click to expand...
Click to collapse
Did you finish the guide fully? Or are you now stuck on a certain step of that guide? If so, which step are you stuck on? Or which step did you last perform to see that your touchscreen stopped working?
bluegreybolt said:
I tried reflashing to a stock firmware and it still doesn't work.
Click to expand...
Click to collapse
Which stock firmware did you flash? And what version of FlashTool did you use to flash it?
LaZiODROID said:
Which custom firmware exactly? And what exactly did you use to flash it?
Click to expand...
Click to collapse
I flashed a custom firmware I made myself according to that guide, and then flashed again with the stock firmware not including the system partition.
LaZiODROID said:
Did you finish the guide fully? Or are you now stuck on a certain step of that guide? If so, which step are you stuck on? Or which step did you last perform to see that your touchscreen stopped working?
Click to expand...
Click to collapse
Yes, I finished the guide fully, when I rebooted at the end the touchscreen was unresponsive.
LaZiODROID said:
Which stock firmware did you flash? And what version of FlashTool did you use to flash it?
Click to expand...
Click to collapse
I am using the latest version of FlashTool. I flashed the latest stock firmware available (23.A.5.271 ?) and then tried to restore using Xperia Companion. However the touchscreen is still broken.
bluegreybolt said:
I flashed a custom firmware I made myself according to that guide, and then flashed again with the stock firmware not including the system partition.
Yes, I finished the guide fully, when I rebooted at the end the touchscreen was unresponsive.
I am using the latest version of FlashTool. I flashed the latest stock firmware available (23.A.5.271 ?) and then tried to restore using Xperia Companion. However the touchscreen is still broken.
Click to expand...
Click to collapse
It might be a broken digitzer or something worse, according to your reports, you have flashed firmwars via flashtool with no avail and even used Xperia Companion so it is most likely a hardware issue.
I would suggest you send in the phone to Sony for repairs, hopefully its covered by warranty, and it still would be if the bootloader is locked. Either way it might get expensive so be prepared for that
Godspeed
Revontheus said:
It might be a broken digitzer or something worse, according to your reports, you have flashed firmwars via flashtool with no avail and even used Xperia Companion so it is most likely a hardware issue.
I would suggest you send in the phone to Sony for repairs, hopefully its covered by warranty, and it still would be if the bootloader is locked. Either way it might get expensive so be prepared for that
Godspeed
Click to expand...
Click to collapse
See this is the strange thing. I had this problem about a week ago, when I flashed a different stock firmware to my phone, and the touchscreen stopped working totally. I sent my phone off to Sony for repair, and just received it back, with a brand new replaced display.
Then I flashed a different firmware and got the same problem. The phone is currently with Sony for hopefully another repair covered by warranty.
I didn't think that you could damage your hardware just by flashing, but it seems that way, unless it's just a huge coincidence.
I find it very strange.
Perhaps during flashing it is possible to screw up the digitizer firmware.
Is a sw trouble.... Last mm versión have this trouble
Enviado desde mi hilo y dos yogures desde PetaTalk
I've got what I thnk is this problem - the screen works, but touch doesn't work. It was working until I rooted/flashed with that guide yesterday. Anything else one can try?
same here
I was on Lineage os but when my phone charged to 100% (was disabled) i put it out the charger and enabled it in same time. After this my phone died. i was needed to flash to Miui8.7.4.20 and i stuck i want to back to lineage os. can somebody link me what to do beacuse i feel so crazed and need someone help. For now i am on Mui by xiaomi.eu 7.2.13. Can somebody help me back to lineage?
what happened when you flash the LineageOS rom?
nickalumada said:
what happened when you flash the LineageOS rom?
Click to expand...
Click to collapse
I was unable i was getting this error updater 7 i think
Dearminder said:
I was unable i was getting this error updater 7 i think
Click to expand...
Click to collapse
Wipe system in twrp then flash lineage, happened to me on slimdragons
I already back to it but thanks. Btw The thing that started it all is really weird. I just pluged out The phone when hitted the power button and Poof - my mi5 died and was only seen by pc as qualcom device
Dearminder said:
I was unable i was getting this error updater 7 i think
Click to expand...
Click to collapse
You should flash the 7.3.9 firmware before flashing the lineageos! Read the OP notes before flashing
nickalumada said:
You should flash the 7.3.9 firmware before flashing the lineageos! Read the OP notes before flashing
Click to expand...
Click to collapse
I know, i was doing something wrong because i spend 3 hours to bring it back to life. And i did it