Hi, i think i have problem with my screen, it's not work anymore, so I decided to reflash device with official Rom. But it didn't work.
Moreover before windows system start for the first time ir requires to tap on screen to boot. So now I cannot use my TytnII at all.
Is it any options to boot it without tapping on screen?
Or just to flash with other ROM, but HARdspl is not installed so a bit afraid to brick my phone. please help
hurdleman said:
Hi, i think i have problem with my screen, it's not work anymore, so I decided to reflash device with official Rom. But it didn't work.
Moreover before windows system start for the first time ir requires to tap on screen to boot. So now I cannot use my TytnII at all.
Is it any options to boot it without tapping on screen?
Or just to flash with other ROM, but HARdspl is not installed so a bit afraid to brick my phone. please help
Click to expand...
Click to collapse
install hardspl (same procedure as flashing) and then install rom of your choise if it dosn't work have you done any of the following
dropped it in water
gone in the washing machine
etc.... stuff like that
why don't you get a new digitizer??? it's $10 for kaiser?? i've been changing them like underwear...every half a year.
what is it, what's asking you to click on screen? if it's just a welcome screen, put welcome.not file in root.
papo said:
why don't you get a new digitizer??? it's $10 for kaiser?? i've been changing them like underwear...every half a year.
what is it, what's asking you to click on screen? if it's just a welcome screen, put welcome.not file in root.
Click to expand...
Click to collapse
hehehe funny expression 'changing them like [email protected]
what do you only change your underwear 2 a year
hehe, i live in Lithuania, so price with shipping will be around 25$. I think this isn't very cheap. Finally got screen working, but after 30min of using again no respond to tapping, then again working fine, and after that again no. it's annoying. I think it's problem with digitizer? I haven't it dropped to water, it almost brand new
hurdleman said:
hehe, i live in Lithuania, so price with shipping will be around 25$. I think this isn't very cheap. Finally got screen working, but after 30min of using again no respond to tapping, then again working fine, and after that again no. it's annoying. I think it's problem with digitizer? I haven't it dropped to water, it almost brand new
Click to expand...
Click to collapse
thats good you got it working
hope the problem doesn't happen again
if we assume the problem is harware, it would most likely by at one of two spots.
place, where the ribbon cable is soldered to lcd
or place where two piecies of digitiizer are connnected to each other.
might help if you check on the ribbon and glue a plastic tape all around the edge of digitizer, making it press little bit more on it
well, if that's hw probllem. but first you shoud try different rom. you can reflash without digitizer working. and check for pocket controller or similar if you want you can control pda from pc with it. there are two free and Pocket contr is trial.
if you just want to bypass the "tap here to use your device" message on the first boot up, search for "welcome.not".
create a blank file named "welcome.not" and place it in the root of your sd card and then power on the device for first boot up.
make sure it is a blank file. make sure it is named EXACTLY "welcome.not". if you are doing this with your windows pc, make sure you have turned off "hide file extensions of known file types". otherwise, the file might actually be named "welcome.not.txt" but might show as "welcome.not" on your pc.
search about it for more information.
hi, have tried differnt rom, but problem still persist. screen is not working, but sometimes it starts working very well. but most of the time it not respond. when backlight goes out and touch screen it starts to light but can't touch any options on. So what can be the problem, only digitezer or whole screen?
it was more probable it would be hw. but we need to eliminate all possibilities and reflash was easiest.
Still there is more things which could be the problem.
And there is no way to tell for sure what is it.
Did you say the pda is new? or digitizer?
And then you said when backlight goes off, digitizer will stop working, but still reacting on touch (to light the backlight) Is this right?
When will it stop / start working? Does it change if you press on body - case?
Does it change if you slide keyboard out or in?
There would be a short test each time pda/screen is powered, if digitizer fails in this test, it would be ignored till next test pass. Could this be your case?
digitizer could be broken on corner, or has bad contact inside
- You can test it, if you'll solder test wires on it and measure resistance, which should be around 500 ohms without touch and going down on each touch, can't go higher! test for both H & V
but the same reaction could be if ribbon cable connecting two parts of kaiser is broken (or connector on mobo side)
but if it's new it shouldn't.
and at last there could be problem on mobo. inside the controller chip or on it's connection, soldering. But not very probable.
It definitely looks like bad connection somewhere. You need to find out where, so you'll not buy digitizer if it's good or ribbon cable.
Put plastic tape around digitizer inside, as I wrote before, inspect ribbon cable and digitizer and it's connections. Try to locate event when it goes wrong.
If you'll not open it and check on these things, then maybe get a new part which will show bad, then I don't see how more we could help you.
You can use it without touch screen somehow or get a new phone.
Digitizer is US$8 with shipping to Lithuania. That's really cheap, even for us from central european countries.
http://cgi.ebay.com.au/HTC-P4450-Ka...m&pt=PDA_Accessories&hash=item5192adf317#shId
and ribbon cable have fair price too,
http://cgi.ebay.com.au/Flex-Cable-R...ewItem&pt=PDA_Accessories&hash=item3cadad06a3
papo very informative
All i want to add is that it's easier to replace the whole screen with a digitizer already on as the digitizer is very hard to remove since glued to the glass more than likely will get wrecked and not able to replace new, whereas full kit wont cost a lot more and will be less stress just 4 screws on the back plate of Tilt "where sim door is".
Well, it is not new, i've bought it from one girl, but it's like brand new, no scratching at all, very good condition.
also, yesterday i checked all the connection inside it, but the problem persisted.
I think I have understood what kind off problem it is...when remove sim card it stars to work perfectly. When insert sim, it work some time very well. Then again screen start not to respond, any ideas?
hurdleman said:
Well, it is not new, i've bought it from one girl, but it's like brand new, no scratching at all, very good condition.
also, yesterday i checked all the connection inside it, but the problem persisted.
I think I have understood what kind off problem it is...when remove sim card it stars to work perfectly. When insert sim, it work some time very well. Then again screen start not to respond, any ideas?
Click to expand...
Click to collapse
mm, I know some pretty good spells, but you need a magic wand to make them work. If you don't have any you need to:
tape the screen as I wrote before (half millimeter tape),
if no help, hardwire analog multimeter on digitizer and test it properly (while pda off and open) as I wrote before
tape bended paper across connector on mobo.
OR just get a new digitizer straight away. it's $8 and pretty good chance that it's the issue. it's maybe 50% chance but what I mean is:
You have $200 phone (now on market) let's assign it 200 points
It's working on 20% with digitizer broken, now you have 40 points
digitizer 8 points to add. With 50% chance to fix = 16 points to add
result: by adding 16 points you gain 160 (200 - 40) that's 10x gain = good risk
WTF with my screen? post photos. on the first my screen, on the second lcd screens which are beiing sold on ebay.
I decided to buy new digitizer, but when looked at my screen, it realized have completely different layout where digitizer is connecting to screen. Am i right? Is the digitizers which are sold on ebay will suit my screen?
that's fine. they all work. They are not oem but works well. Maybe not so scratch resistive.
You may get the digitizer solo, but they will not include a special double side tape which goes around and is holding it together. You can make that tape, but it's pain as stylez said. A lot of cleaning the used old one, then cutting small strips of ds-tape. and you need to put a paper or something in between two layers of tape as you need a little space in between. And then soldering that ribbon. Better just get whole assembly.
==
I see you tried that tape, before you buy it, try the last thing. The place where digitizer is soldered to lcd modul.
On that piece you sent photo of, you need to open back cover.
check the picture:
1. peel off antistatic tape from connector, from up -> down
2. take cover off
3. there will be attachment of digitizer behind the cover, like on your second picture.
Check for good connection
AND
check if soldered pins could not be touching the back cover you took off
( i had this problem once)
put electric tape accross it a give it a try - that will isolate it from back cover & make a little pressure if bad connection
=
Hi all ... I have my HTC Diamond for about a year. I love this phone, and I don't want another, but today, unfortunately he has a very strong fall. I always had very, very careful with it. But today was the time, the phone crashed, broke away from the back cover and battery, and I thought to myself, if not damaged by this fall, he would never break down. I put the battery, put the cover, turn it on, he vibrate on startup, but nothing else, the phone went blank, I was waiting, and then there gave the sound of that presentation of HTC, but no picture, no lights on the keys, nothing ... I'm really sad, I have no idea what it is. Already dismantled a bit cuz I thought it was some form of contact to the screen that is hung up, but no, it's all good inside. Does anyone know what could be?
Sorry for the bad english (google translator)
Please... can anyone help me?
could be flex connecting Display to motherboard damage. Send to HTC center to check
My diamond did the same thing, just open it up and connect the flat plastic display cable back into it's little plastic connector on the motherboard. Takes all of 15min to do and there is no way you can screw it up
gripen40k said:
My diamond did the same thing, just open it up and connect the flat plastic display cable back into it's little plastic connector on the motherboard. Takes all of 15min to do and there is no way you can screw it up
Click to expand...
Click to collapse
Thx... but since then, I already repair it, not me, and the guy make me pay 20€ for that... and now my GPS doesn't work. By what I searched, may be it's the coaxial antenna that is not connect, or I heard that after deconnected, it can't be re-used.
But I don't know where to buy a new one...
Well at least try opening it up and seeing if anything is broken. The guy who fixed it probably disconnected it on purpose so you have to pay him more to fix it again
I have also gone through the same problem last month. As my small cousin came from abroad, he threw the phone like wrapper of the chocolate but I send the phone to the repairing center and it is well now.
My Droid's touch screen isn't working in the center vertically all the way down. I can still use the 'edges' of the screen. I need to use the middle of the screen for a few things (not transfering stuff over). Is there any way I can 'project' my Droids screen to my computer and click/touch in it to use it?
Thanks in advance for all help. It's appreciated
~mfungah
Edit: This is the original Motorola Droid.
I have the same problem on the right side of my milestone :S
I had the same problem, but from the back arrow upwards, specially when the phone got hot. As my phone was still on the warranty period, I flashed it back to stock and updated it to the official 2.2., took it to an Orange shop and got it back after almost a month: they basically changed the whole top part of the phone (I got a brand new screen )
Repair problem
I had a same failure. The touch panel was bad. I ordered one from eBay. It also came as well put it. It works well. Only so much wrong with me that for some reason the phone stacked in landscape mode, I can't change to portrait mode. What is wrong? I put together something wrong? I do not think so. Everything else goes. (or so it seems)
This has to do with the digitizer (the glass you touch over the top of the LCD you see) being defective or unsealed. This is due to environmental moisture finding its way into the phone and f**king with the electrictal signals sent by touching the screen. There is a 'phantom touch' issue that seems to happen before or during the vertical unresponsiveness, and that can usually be temporarily remedied by firmly pushing your screen downwards (your phone may restart) and taking a blowdryer to your phone until it's just hot enough to be uncomfortable to hold (and no longer take it into the bathroom while you shower). One way or another, you're going to have to replace your digitizer eventually.
Sent from my Droid using XDA App
I had the same problem months ago but it's now fixed.
STEPS:
1. Digitizer I bought from this guy:
http://cgi.ebay.ph/New-Touch-Screen-Digitizer-Motorola-Milestone-A853-/270780531 891?pt=UK_Replacement_Parts_Tools&hash=item3f0bc704b3#ht_2811wt_850
2. Dissasembly Videos (I advice you to watch them repeatedly before dissasembly):
http://www.youtube.com/watch?v=6d7ETMfgq2s
http://www.youtube.com/watch?v=dE81IaQHEHc
3. Phillips screw driver( for dealing with hard screws around the screen): Because I don't want you to use the low quality screw driver supplied with the digitizer.
4. Double sided tape: I got mine from a hardware shop for only P19. Buy a the more expensive tape(P100+) but look for a very thin one! You will use the cheap weak tape to stick some internal parts and use the Hard tape to stick the external casing. EDIT: I just used the cheap one for everything and it's strong enough.
5. PATIENCE: Don't be in a hurry. I even paused from time to time to get a better idea about what to do next. Get the feel of being a perfectionist (that same additude when I applied a screen protector )
That's the guide from me who haven't dissasembled a phone in my entire life but my milestone. So if something bad and technical that happens along the way then my knowledge can't help.. sorry.
Good luck bro!!
I turned on my phone earlier to notice that the screen was suddenly completely white at full brightness whenever it was on, still touch responsive as I can hear it. This is happening immediately upon boot, not even showing the Samsung nor AT&T logos, so I believe it is a hardware issue. Has anyone else had this happen? If so, is there a solution short of getting a replacement? Maybe tearing it down and reseating the connector or something? I don't know, just a bit upset and rambling, sorry
Tore it down and undid and reseated every ribbon cable I saw, didn't help. Ordered a replacement should get it in a few days, might sell the old one for parts to recuperate some of the costs or maybe pick up one of the media docks that does TV out and USB host as well as charging, see if I can convert it to a set top box, assuming the dock will work without any setup on the phone itself