Marshmallow kernals - T-Mobile Galaxy Note 4 Q&A, Help & Troubleshooting

Are their currently any kernals which support marshmallow now? I installed emotions kernals but the wifi doesn't work and I do not know how to get back to stock kernel.
Thank you

hunter99507 said:
Are their currently any kernals which support marshmallow now? I installed emotions kernals but the wifi doesn't work and I do not know how to get back to stock kernel.
Thank you
Click to expand...
Click to collapse
try flashing dr.ketens data fix in recovery.

funtimez said:
try flashing dr.ketens data fix in recovery.
Click to expand...
Click to collapse
Using an N910t3 I flashed emotion MM rc25 , confirmed wifi didn't work, tried the data fix it put me in a bootloop, luckily I had made a complete backup in TWRP and restored it already, just want to warn anyone else before they try it.

You should keep A backup of the original the "boot" partition in twrp. In TWRP>Backup>select "boot" only. That keeps the stock kernel.
I haven't tested any alternative kernels personally.
I feel that the stock MM kernel is doing great.

MM works fine. I'm waiting for MM kernel
I had a few problems with Marshmallow but finally installed the latest PG2. My phone N910T boot looped and caused some problems but eventually I finally had a working 6.0.1 stock. I installed TWRP and SuperSU SYSTEMLESS and used the phone for 2 days.
I tried flashing Beastmode and Emotion kernels but neither worked and I was stuck in a boot loop. Eventually I tried to reinstall stock without a wipe as this always works and keeps my apps etc.
The stock said the md5 checksum was invalid even though it was the same file from 2 days earlier. To fix this I removed the file extension, preventing it from doing the MD5 check and attempted to install. It bricked my phone as the process appeared to stop at halfway and I aborted. I found modem and bootloader files for PG2 and took a shot at installing them. I got to another bootloop.
I tried the stock tarfile again and was a little more patient this time. The previous delay was only a few minutes long. It installed succesfully. I Installed TWRP with ODIN, followed by a systemless root in recovery mode.
I'm currently waiting for MM kernels. I hope my little adventure helps somebody else on their journey.

FungusTB said:
I had a few problems with Marshmallow but finally installed the latest PG2. My phone N910T boot looped and caused some problems but eventually I finally had a working 6.0.1 stock. I installed TWRP and SuperSU SYSTEMLESS and used the phone for 2 days.
I tried flashing Beastmode and Emotion kernels but neither worked and I was stuck in a boot loop. Eventually I tried to reinstall stock without a wipe as this always works and keeps my apps etc.
The stock said the md5 checksum was invalid even though it was the same file from 2 days earlier. To fix this I removed the file extension, preventing it from doing the MD5 check and attempted to install. It bricked my phone as the process appeared to stop at halfway and I aborted. I found modem and bootloader files for PG2 and took a shot at installing them. I got to another bootloop.
I tried the stock tarfile again and was a little more patient this time. The previous delay was only a few minutes long. It installed succesfully. I Installed TWRP with ODIN, followed by a systemless root in recovery mode.
I'm currently waiting for MM kernels. I hope my little adventure helps somebody else on their journey.
Click to expand...
Click to collapse
You're able to flash TWRP and root on stock PG2 for N910T?

thebestiam said:
You're able to flash TWRP and root on stock PG2 for N910T?
Click to expand...
Click to collapse
Yes it works. I'm experiencing battery drain through.

FungusTB said:
Yes it works. I'm experiencing battery drain through.
Click to expand...
Click to collapse
Doesn't it update the bootloader to PG2 from PE3 and it'll still work?
Sent from my GT-I9500 using XDA-Developers mobile app

thebestiam said:
Doesn't it update the bootloader to PG2 from PE3 and it'll still work?
Click to expand...
Click to collapse
I don't know. I've upgraded bootloader in the past without issues. There seems to be issues surrounding mismatched modems and bootloader recently.

FungusTB said:
I don't know. I've upgraded bootloader in the past without issues. There seems to be issues surrounding mismatched modems and bootloader recently.
Click to expand...
Click to collapse
Okay, thanks for the clear up
Sent from my SM-N910T using XDA-Developers mobile app

Related

Newly Rooted 4.4.2 - Only boots to recovery

Okay guys so I just rooted my att note 3 that was completely up to date using the towelroot.com method found here. Stupidly of me I was trying to follow a thread to change my system language in build.prop but after doing that It ONLY boots to recovery / safestrap. After the safestrap screen I tell it to continue to boot normaly and all i get after that is a black screen.
Any ideas? Is it possible to flash safestrap from odin / heimdall / recovery?
Ive tried factory resetting from safestrap and recovery and that didn't change anything.
I not even sure I have safestrap at this point I can get into recovery, and download mode but it sits at the "Samsung Galaxy NOTE 3 [Unlocked Icon] Custom" screen. It wont actually progress to the safestrap.
Before I tried to edit that build.prop the root / safestrap worked fine all day today, restarted several times for different reasons and still worked afterwards.
I had no encryption enabled.
Via recovery -
"Android system recovery <3e>
KOT49H.N900AUCUCNC2"
**** This Worked ****
Possibly? this as a fix?
Would this be okay to use as a stock Kitkat firmware resource for an Odin flash?
Anyone have a N900AUCUCNC2 ROM or firmware I can flash?
BLMaros said:
Anyone have a N900AUCUCNC2 ROM or firmware I can flash?
Click to expand...
Click to collapse
i have the .zip files for it and odin 3
*it sounds to me like a bootloop or a softbrick, I would recommend using this odin 3 and flash the stock kk rom the one i have is the unofficial and is pre-rooted. but it works when i bricked mine repeatedly trying roms.
farmerj said:
i have the .zip files for it and odin 3
*it sounds to me like a bootloop or a softbrick, I would recommend using this odin 3 and flash the stock kk rom the one i have is the unofficial and is pre-rooted. but it works when i bricked mine repeatedly trying roms.
Click to expand...
Click to collapse
That'd be awesome if you could get that to me some how. I more or less have everything fixed but the wake-up after entering my pattern lock is ungodly slow so I'd like to possibly try a different one.
BLMaros said:
That'd be awesome if you could get that to me some how. I more or less have everything fixed but the wake-up after entering my pattern lock is ungodly slow so I'd like to possibly try a different one.
Click to expand...
Click to collapse
I am assuming you know how to use odin.
https://www.dropbox.com/s/2hl1s7pvf5jatbm/NC2_Bootloader_N900AUCECMLG_VER_2.zip
hope this helps. let me know
farmerj said:
I am assuming you know how to use odin.
https://www.dropbox.com/s/2hl1s7pvf5jatbm/NC2_Bootloader_N900AUCECMLG_VER_2.zip
hope this helps. let me know
Click to expand...
Click to collapse
I do, this is perfect thank you!
Did it work?
Sent from Awesome Note 3 At&t
running Purerom CE.

Root, Backup & ROM Verizon LG G2 on 4.4.2???

I can't seem to find a process for backing up my current "stock" setup, then rooting it and installing TWRP and ROM's.
I had a G2 previous to it getting kitkat and had done all of this with that, fairly easily too...but can't seem to find the same process to do it after the kitkat update (4.4.2)...?
Any help would be greatly appreciated.
sdgmcdon said:
I can't seem to find a process for backing up my current "stock" setup, then rooting it and installing TWRP and ROM's.
I had a G2 previous to it getting kitkat and had done all of this with that, fairly easily too...but can't seem to find the same process to do it after the kitkat update (4.4.2)...?
Any help would be greatly appreciated.
Click to expand...
Click to collapse
You need to root it (using ioroot), install a recovery (using autorec) then you can back it up.
mjones73 said:
You need to root it (using ioroot), install a recovery (using autorec) then you can back it up.
Click to expand...
Click to collapse
This worked to get twrp on it thanks! ks (i was able to eventually get it rooted using ioroot and did a nandroid backup), i am however not able to flash a new rom (using cm's latest nightly for the vs980 now...going to try the snapshot next, but the nightly just fails almost immediately and i did have twrp fix permissions????
thanks again!
EDIT: And crap, stuck in a boot loop...said it flashed the snapshot ok, almost immediately, rebooted and boot loop.
mjones73 said:
You need to root it (using ioroot), install a recovery (using autorec) then you can back it up.
Click to expand...
Click to collapse
It's official, I'm bricked...lg logo boot loop, nothing else. Somehow in the process my nandroid and twrp backups no longer show up in twrp either (have to do the factory reset (hold down vol down and power twice, then power twice to confirm reset)...I've looked in the backup folders using twrp file manager and the folders have lots of stuff in them (not sure if it's correct stuff though?) and the folders are named as I named them when I did the backups...also, most other data seems to be on the phone and only 13gb's free according to twrp, so has to be a "system" there, but just get boot loop...
I've since read that the cm builds dont work on 24a kk 4.4.2 vs980; results in boot loops, but I can't get adb to work either so I can't even download a different rom to get it going...
I'm stuck...way stuck....
sdgmcdon said:
This worked to get twrp on it thanks! ks (i was able to eventually get it rooted using ioroot and did a nandroid backup), i am however not able to flash a new rom (using cm's latest nightly for the vs980 now...going to try the snapshot next, but the nightly just fails almost immediately and i did have twrp fix permissions????
thanks again!
EDIT: And crap, stuck in a boot loop...said it flashed the snapshot ok, almost immediately, rebooted and boot loop.
Click to expand...
Click to collapse
Did you use jackpotcalvin's cm11? If not then you're in a bootloop because the official cm11 for our phone users 4.2.2 kernel base, whereas jpc's uses kk kernel.
Can you get into download mode? If so, return to stock using kdz or tot method (I've used tot, fairly easy).
Sent from my VS980 4G using XDA Premium 4 mobile app
ADB Sideload may work for you.
http://teamw.in/ADBSideload
Boot into TWRP, Advanced, ADB Sideload.

[Q] Can't Root or Install TWRP

Hey guys. I'm hoping someone with more knowledge will be able to help. I was previously rooted using CF Autoroot and tried to install TWRP when it was released. Tried to flash it with Odin but it failed so I Odined to the latest firmware and tried to reroot but that failed and I'm currently unrooed.
Any ideas?
Same.
i also using that cf-root. i have no problem rooting it. just make sure usb debug check and follow guide. i did it on 2 of my note 4 both with no problem.
solographics said:
Hey guys. I'm hoping someone with more knowledge will be able to help. I was previously rooted using CF Autoroot and tried to install TWRP when it was released. Tried to flash it with Odin but it failed so I Odined to the latest firmware and tried to reroot but that failed and I'm currently unrooed.
Any ideas?
Click to expand...
Click to collapse
Reflash back to stock using ODIN, root using CF-Root, download Flashify from the Play Store and use that to flash TWRP. Of course, follow all directions to each step to the "T".
I'll give that a try tonight after work and report back.
solographics said:
I'll give that a try tonight after work and report back.
Click to expand...
Click to collapse
Mine said "failed" too. Nothing I could do would make any difference. So I unplugged the phone, pulled the battery waited a few seconds and powered back on. To my amazement, the rooting process continued and when it rebooted, I was rooted. Same thing happened when I odined twrp.
Charlie
Same thing happened to me! Been struggling with this 24 hrs now.
Solved!!!
I solved my problem by doing a factory reset on the phone in the settings>backup/reset>factory reset or something like that then going through the rooting process outlined by TEKHD.
Hope this helps everyone else having the same problem.
OK I GOT IT GUYS! If you have the reactivation lock checked in the security setting then its preventing odin from doing its thing. Just uncheck that and it should work.

Rooted SM-T810 not booting

Hi,
On Wednesday I rooted my SM-T810 (with Android 5.0.2) with cf-autoroot and after that I installed TWRP from this XDA forum.
I took a Nandroid backup and then I installed the CM12.1 root from T_I.
It worked perfectly.
But now after I switch the tablet off and on it doesn't get past the Samsung screen.
I can go to download mode and I then I am able to flash cf-autoroot again with Odin.
After that it starts up, but the problem occurs again the next time I power the tablet off.
I can flash the tablet with a Samsung firmware from SamMobile, but I also have a LG G4 and an older Samsung Galaxy Tab S 8.4 both with CM, so I really would like to keep using CM.
Any ideas how to fix this?
Disable cm root in developer settings.
No, that didn't work either.
I reflashed a sammobile image, but still the same issue.
Then I installed twrp 3.0 and could boot to it (through download mode).
I reinstalled CM12.1 and it works as long as I don't switch the tablet off.
Unfortunally I cannot return it, because of the knox trip counter.
jaap2012 said:
No, that didn't work either.
I reflashed a sammobile image, but still the same issue.
Then I installed twrp 3.0 and could boot to it (through download mode).
I reinstalled CM12.1 and it works as long as I don't switch the tablet off.
Unfortunally I cannot return it, because of the knox trip counter.
Click to expand...
Click to collapse
Have you tried flashing stock firmware from sammobile with odin? It should fix all problems and you should boot.
Have you tried flashing stock firmware from sammobile with odin? It should fix all problems and you should boot.
Click to expand...
Click to collapse
Yes, that didn't work.
I think it cannot erase the volumes back to stock?
ok, I fixed it by restoring the full Nandroid backup.
It is booting and working again.
I think it must have been an issue with the boot image or so.
I'll start over with CM12.1 next weekend...
jaap2012 said:
ok, I fixed it by restoring the full Nandroid backup.
It is booting and working again.
I think it must have been an issue with the boot image or so.
I'll start over with CM12.1 next weekend...
Click to expand...
Click to collapse
You had a nandroid backup but didn't use that first? :sly:
ashyx said:
You had a nandroid backup but didn't use that first? :sly:
Click to expand...
Click to collapse
Yeah, sorry.
I didn't expect that that would fix this boot problem, because this restore already has superSU installed.
jaap2012 said:
Yeah, sorry.
I didn't expect that that would fix this boot problem, because this restore already has superSU installed.
Click to expand...
Click to collapse
A nandroid almost always fixes the issue if it was made from a working system.

[Q] can't install TWRP on SM-T810 running Nougat

I just received a Galaxy S2 SM-T810 running Nougat. It appears to be in perfect condition. I have Odin 3.1.2. and TWRP twrp_3.1.0-1_sm-t810_13317.tar. I have been unable to get TWRP installed. I have made multiple attempts, and it keeps the stock recovery.
Can anyone tell me why this is failing? Odin says it was successful. Any help would be appreciated. :crying:
Thanks in advance.
Try it again without Odin. ADB..
C0BRA01 said:
I just received a Galaxy S2 SM-T810 running Nougat. It appears to be in perfect condition. I have Odin 3.1.2. and TWRP twrp_3.1.0-1_sm-t810_13317.tar. I have been unable to get TWRP installed. I have made multiple attempts, and it keeps the stock recovery.
Can anyone tell me why this is failing? Odin says it was successful. Any help would be appreciated. :crying:
Thanks in advance.
Click to expand...
Click to collapse
Do you have oem unlock switched on as well?
C0BRA01 said:
I just received a Galaxy S2 SM-T810 running Nougat. It appears to be in perfect condition. I have Odin 3.1.2. and TWRP twrp_3.1.0-1_sm-t810_13317.tar. I have been unable to get TWRP installed. I have made multiple attempts, and it keeps the stock recovery.
Can anyone tell me why this is failing? Odin says it was successful. Any help would be appreciated. :crying:
Thanks in advance.
Click to expand...
Click to collapse
A proper read of the instructions would solve it.
SonderTech said:
Do you have oem unlock switched on as well?
Click to expand...
Click to collapse
There was no option to do that. I looked thinking that might have been it,
Deleted.
C0BRA01 said:
Thank you. that's was quite useless.
I have flashed TWRP on quite a few devices.
I kept getting a weird screen instead of TWRP and I used ODIN 3.12.3 and TWRP 3.1.0-1 and then tried 3.1.1.1 that failed too. I finally ended up using ODIN 3.12.5 and TWRP 3.1.0-1 I also had flashed the tablet back to 6.01, and then back to 7.0. When I tried to use ODIN to reflash directly to 7.0 again it basically didn't do anything so I had to flash backward first. I think the partitions for my stock ROM were somehow messed up, and flashing back to 6.01 and then back up to 7.0 fixed it. Even with that, I had to use the older TWRP 3.1.0-1 I think that was the worst time I ever had getting a device rooted.
Click to expand...
Click to collapse
Google's new API might have something to do with that. I'm not sure. Did you end up getting a systemless root on the device with 6.0 and above
SonderTech said:
Google's new API might have something to do with that. I'm not sure. Did you end up getting a systemless root on the device with 6.0 and above
Click to expand...
Click to collapse
yes I installed Majisk.
C0BRA01 said:
yes I installed Majisk.
Click to expand...
Click to collapse
Oh ok

Categories

Resources