Debrand Huawei p9 - Huawei P9 Questions & Answers

Hello everybody, I am trying to debrand my new Huawei p9. I have tried the dload method explained in the development section but I can't manage to make the upgrading start: when I press both volume buttons and turn on (with the downloaded dload folder inside the micro SD) the device simply vibrates two times and then reboot. Do you know if I am doing anything wrong or if there are other methods? Any help would be appreciated. Thanks a lot
PS: I'm sorry if I am opening a new thread but xda doesn't let me reply to the original thread because I don't have the right to post in the development section of the forum.

You must press them at the same time, turn off the device and press the vols buttons first and them the power button. The .rar/.zip must be uncompressed on the SD.

HI thank you for your help, but that is exactly what I did: unzipped the file (which contained only the dload folder) and put it in the root of the micro sd. I turned off the phone and pressed the volume buttons (up and down) together and then pressed the power button. The phone vibrated twice then the logo appeared then the screen became back and then again the logo and this loop continued until I stopped pressing the volume buttons. Anyway I don't have the phone with me now so I'll try again tomorrow. Will it work also if I put the dload folder inside the internal memory?

put file, sd card dload folder work. I dont try in internal memory.

general91 said:
HI thank you for your help, but that is exactly what I did: unzipped the file (which contained only the dload folder) and put it in the root of the micro sd. I turned off the phone and pressed the volume buttons (up and down) together and then pressed the power button. The phone vibrated twice then the logo appeared then the screen became back and then again the logo and this loop continued until I stopped pressing the volume buttons. Anyway I don't have the phone with me now so I'll try again tomorrow. Will it work also if I put the dload folder inside the internal memory?
Click to expand...
Click to collapse
only hold down the volume up and down keys with power at same time until you see the Huawei logo then let go. do not carry on holding them down - this is what was causing your phone to loop

Thanks for the help it worked! I spent so much time trying to understand what I was doing wrong while it was so simple.

general91 said:
Thanks for the help it worked! I spent so much time trying to understand what I was doing wrong while it was so simple.
Click to expand...
Click to collapse
you're welcome - often can be simple with phones, other times not so

Debrand p9 vodafone IT
Hello,
I would like to debrand my phone. I read some guide here and I will use srk tool.
Now I'm on c02b133.
Which is the correct procedure?
have I to install via dload c432b136, go to c900 and then unlock bootloader, root e oem info file?
Or have I to unlock bootloader, root, oem info file and then flash the rom c432?.
I have this doubt because in some post, someone told to reinstall stock recovery after root, and forced the installation of the stock rom..so I'm not sure about correct way.
Thank to everyone
Massimiliano

maxmax91 said:
Hello,
I would like to debrand my phone. I read some guide here and I will use srk tool.
Now I'm on c02b133.
Which is the correct procedure?
have I to install via dload c432b136, go to c900 and then unlock bootloader, root e oem info file?
Or have I to unlock bootloader, root, oem info file and then flash the rom c432?.
I have this doubt because in some post, someone told to reinstall stock recovery after root, and forced the installation of the stock rom..so I'm not sure about correct way.
Thank to everyone
Massimiliano
Click to expand...
Click to collapse
Can you share thread which you got c432? I have L09C440B138 and want to L09B432 open market nougat

Related

Soft-bricked Huawei Ascend P7?

I have tried to root my Huawei Ascend P7 L10 phone, using Root Genius and also Kingo Root through my Windows PC.
The rooting has not been complete, something has been messed up on my phone.
When I try to enter recovery mode (volume + and -, and power), the led slowly blinks green and red, and the screen shows this message:
"Unfortunately boot failed, get more information... (Chinese letters) ...shutdown/rescue mode..."
After choosing rescue mode, the screen says "...Phone unlocked"...
I have several times tried to collect information on how to solve this, but the threads contain bits and pieces and partly tutorials/videos.
I would like to find a complete step-by-step tutorial on how to deal with this problem.
Also I have read that I need to install ADB, SDK, this and that, but it's hard to follow the instructions from beginning to end.
Can anyone help me with this?
Have you found a solution?
jonnynordhus said:
I have tried to root my Huawei Ascend P7 L10 phone, using Root Genius and also Kingo Root through my Windows PC.
The rooting has not been complete, something has been messed up on my phone.
When I try to enter recovery mode (volume + and -, and power), the led slowly blinks green and red, and the screen shows this message:
"Unfortunately boot failed, get more information... (Chinese letters) ...shutdown/rescue mode..."
After choosing rescue mode, the screen says "...Phone unlocked"...
I have several times tried to collect information on how to solve this, but the threads contain bits and pieces and partly tutorials/videos.
I would like to find a complete step-by-step tutorial on how to deal with this problem.
Also I have read that I need to install ADB, SDK, this and that, but it's hard to follow the instructions from beginning to end.
Can anyone help me with this?
Click to expand...
Click to collapse
What is your firmware version?
As far as I know that you could try to flash stock recovery and boot image and then download a compatible firmware for your phone and then force upgrade it which would solve the problem.
how chek firmware version help meeeeeee
amankha said:
how chek firmware version help meeeeeee
Click to expand...
Click to collapse
go to setting, and about phone
@jonnynordhus, i've already helped someone with a similar problem, try this:
Download B852 official ROM and copy it to root of your SD card to a new folder "dload"
It should look like this "/dload/UPDATE.APP"
Extract UPDATE.APP (on your computer) using Huawei Update Extractor (all files)
Go into bootloader (Power + Vol Down)
Now open command line and use ADB (Android Debugging Bridge) to send following commands to your phone:
fastboot flash recovery RECOVERY.IMG
fastboot flash boot BOOT.IMG
Now force update by turning off your phone, and turing him back on while holding all 3 buttons pressed down.
When screen comes on release the Power button but keep holding both Volume rockers pressed down until you see an EMUI logo.
If for any reason it fails to install, go back into recovery and do Wipe data/Factory Reset, and than try again.
Let us know how it went

I cant figure out my problem

Hello everybody !
I'm here today because i have a problem I can not figure out.
When I got my ascend p7 I download a room I found on this website called "My rom v3.3 B609" to enjoy the emiu 3. Everything works fine, I am really happy of this rom. But I wanted to upgrade my phone, in order to get android L. It's been more than two months that I try, look for answers and so on but nothing works.
Everytime that I want to flash a new rom, the CWM ( 6.0.5.0 ) tells me " installation aborded". And no matter what rom it is, it does not work. I've heard about the Notepad method but I can not find the sentences to delete.
I am really stuck, I can not even downgrad. My CWM wont let me do anything.
So if somebody could tell me what is the problem, it would be really good.
Thank you in advance !
in order to flash a original firmware you need to replace the cwm with the designated recovery.img of the rom you want, also you need to flash the boot.img of the same rom you want..then you have to force update with the 3 button method..
search around the forum..it is described several timea in many threads..
Gesendet von meinem Mate S CRR-L09 B303
maximefontn said:
Hello everybody !
I'm here today because i have a problem I can not figure out.
When I got my ascend p7 I download a room I found on this website called "My rom v3.3 B609" to enjoy the emiu 3. Everything works fine, I am really happy of this rom. But I wanted to upgrade my phone, in order to get android L. It's been more than two months that I try, look for answers and so on but nothing works.
Everytime that I want to flash a new rom, the CWM ( 6.0.5.0 ) tells me " installation aborded". And no matter what rom it is, it does not work. I've heard about the Notepad method but I can not find the sentences to delete.
I am really stuck, I can not even downgrad. My CWM wont let me do anything.
So if somebody could tell me what is the problem, it would be really good.
Thank you in advance !
Click to expand...
Click to collapse
Download B852 official ROM and copy it to root of your SD card to a new folder "dload"
It should look like this "/dload/UPDATE.APP"
Extract UPDATE.APP (on your computer) using Huawei Update Extractor (all files)
Go into bootloader (Power + Vol Down)
Now open command line and use ADB (Android Debugging Bridge) to send following commands to your phone:
fastboot flash recovery RECOVERY.IMG
fastboot flash boot BOOT.IMG
Now force update by turning off your phone, and turing him back on while holding all 3 buttons pressed down.
When screen comes on release the Power button but keep holding both Volume rockers pressed down until you see an EMUI logo.
If for any reason it fails to install, go back into recovery and do Wipe data/Factory Reset, and than try again.
Let us know how it went
Milan-XDA said:
Download B852 official ROM and copy it to root of your SD card to a new folder "dload"
It should look like this "/dload/UPDATE.APP"
Extract UPDATE.APP (on your computer) using Huawei Update Extractor (all files)
Go into bootloader (Power + Vol Down)
Now open command line and use ADB (Android Debugging Bridge) to send following commands to your phone:
fastboot flash recovery RECOVERY.IMG
fastboot flash boot BOOT.IMG
Now force update by turning off your phone, and turing him back on while holding all 3 buttons pressed down.
When screen comes on release the Power button but keep holding both Volume rockers pressed down until you see an EMUI logo.
If for any reason it fails to install, go back into recovery and do Wipe data/Factory Reset, and than try again.
Let us know how it went
Click to expand...
Click to collapse
Thank you very much, it worked !
maximefontn said:
Thank you very much, it worked !
Click to expand...
Click to collapse
Happy to help

EVA-L09C150: Change firmware to C432. Possible?

Hi all,
I have a branded L09C150B182 huawei P9 phone.
Is it possible to change the firmware to a C432 in order to debrand it?
If yes, how can I do it? I am totally new to Huawei.
Thanks a lot for your help
******************************
Solution summary
I successfully debranded my L09C150B182 to L09C432B182
I followed the instructions given in the video tutorials:
1.) [HOW-TO] Root Huawei Phone with SRKTool Huawei
https://www.youtube.com/watch?v=AMNVruAU6do
2.) [GUIDE] How to debrand Huawei Phone by SRK Tool Huawei
https://www.youtube.com/watch?v=JZVsIKtdgV4
I skipped the step change ro.build.display.id, as my phone automatically installed a C900 firmware after I changed the OEM info
3.) After installing C900 firmware, I used the dload method to upgrade to C432 firmware e.g. by using the following dload method
https://forum.xda-developers.com/p9/...-b136-t3382818
Thanks a lot for your help and assistance
Sent from my D5803 using XDA Free mobile app
Possible...you must unlock bootloader, root and debrand
https://forum.xda-developers.com/p9/how-to/guide-root-huawei-p9-t3367800
https://forum.xda-developers.com/p9/how-to/vdo-guide-how-to-debrand-huawei-phone-t3410045
hanniSK said:
Possible...you must unlock bootloader, root and debrand
https://forum.xda-developers.com/p9/how-to/guide-root-huawei-p9-t3367800
https://forum.xda-developers.com/p9/how-to/vdo-guide-how-to-debrand-huawei-phone-t3410045
Click to expand...
Click to collapse
Thanks a lot for your reply. All went smooth but at the end I bricked the phone. Please check the following post in which I documented my current issue:
https://forum.xda-developers.com/p9/help/p9-bricked-t3538840/post70570522#post70570522
Any idea how to solve this Problem?
Don't worry, just flash a stock rom again using the dload method... this one for example.... https://forum.xda-developers.com/p9/development/stock-rom-dload-file-p9-eva-l09-b136-t3382818
You will have to unlock bootloader, flash TWRP and SuperSU again if you want root.
Hi colthekid,
thanks for your fast reply. I tried the dload method yesterday but it was not working. The Firmware from Flash Card in the phone was not loaded.
So I have to press both volume + and volume - and power to make that happen?
I just took a brand new Flash Card (without formatting the same in the phone) and copied over the dload Folder from the link above.
Maybe there is an issue because I am still having an open bootloader?
Thanks, morro
morro23 said:
Hi colthekid,
thanks for your fast reply. I tried the dload method yesterday but it was not working. The Firmware from Flash Card in the phone was not loaded.
So I have to press both volume + and volume - and power to make that happen?
I just took a brand new Flash Card (without formatting the same in the phone) and copied over the dload Folder from the link above.
Maybe there is an issue because I am still having an open bootloader?
Thanks, morro
Click to expand...
Click to collapse
Yep, phone turned off, hold vol up & vol down then press power until boots into erecovery. Update should start automatically. Don't have phone connected to PC, although mains power is fine.
The dload folder (with update files inside) needs to be at the root of the SD card (not inside another folder) so a blank/formatted card is good. An unlocked bootloader is irrelevant, I've done this with both an unlocked and a locked bootloader and the update process locks it again anyway.
When you tried before did the update start in erecovery, but fail at a %, or did you not get into erecovery?
colthekid said:
Yep, phone turned off, hold vol up & vol down then press power until boots into erecovery. Update should start automatically. Don't have phone connected to PC, although mains power is fine.
The dload folder (with update files inside) needs to be at the root of the SD card (not inside another folder) so a blank/formatted card is good. An unlocked bootloader is irrelevant, I've done this with both an unlocked and a locked bootloader and the update process locks it again anyway.
When you tried before did the update start in erecovery, but fail at a %, or did you not get into erecovery?
Click to expand...
Click to collapse
Hi. Yesterday when I tried the dload on SD Card it did not boot into erecovery at all. It went into a Screen where "Your device has been unlocked and can't be trusted .... Your device is booting now... " was shown. Here the System stuck until forever. But maybe I did not hold vol up & vol down and pressed power Long enough. At the moment I can not turn the phone of as it always boots again when I try to turn it off. Hopefully this is not a Problem.
Do I copy over the complete dload Folder or only the UPDATE.app file? As far as I remember there were two other subfolders in the dload Folder. Are These required as well?
I will try today evening after work and let you know if it is working. Thanks
morro23 said:
Hi. Yesterday when I tried the dload on SD Card it did not boot into erecovery at all. It went into a Screen where "Your device has been unlocked and can't be trusted .... Your device is booting now... " was shown. Here the System stuck until forever. But maybe I did not hold vol up & vol down and pressed power Long enough. At the moment I can not turn the phone of as it always boots again when I try to turn it off. Hopefully this is not a Problem.
Do I copy over the complete dload Folder or only the UPDATE.app file? As far as I remember there were two other subfolders in the dload Folder. Are These required as well?
I will try today evening after work and let you know if it is working. Thanks
Click to expand...
Click to collapse
The "device has been unlocked" screen is before booting into system (with 3 instructions) or a shorter one before either erecovery or TWRP (no messages). That's standard and nothing to worry about, it just shows your bootloader is unlocked.
Copy everything over and into the dload folder . So for the B136 stock rom, the dload folder should contain update.app and the hw and dt folders. Some updates may only have an update.app bit.
It's easier if the phone was off, but whatever state the phone is in, press and hold both volume keys and power & keep them held until you enter erecovery. Think you can let go of them once the phone boots, but I've always kept them pressed untill the update starts.
Thank you very much for your help colthekid
I successfully updated to B136 and afterwards to B182
It worked out fine :good:
So c432 is the unbranded rom? Where are you from? What is the c150 like in comparison? I also have the c150 (Austria) and do ned find any branding (loading screen or preinstalled apps).
Did you already got an update to nougat?

huawei p9 plus blocked on logo

sorry for my english
please help i brick my huawei p9 plus vie-l29 after try to install a new framware it is blocked on logo an can enter only to fastboot & rescue mode
Foul restart by holding down the volume button in the upper part (+). In recovery you do comes out of the 2 formats that are indicated and so you starts with the configuration of fabrica.
Grlschia said:
Foul restart by holding down the volume button in the upper part (+). In recovery you do comes out of the 2 formats that are indicated and so you starts with the configuration of fabrica.
Click to expand...
Click to collapse
sorry but the phone dont start to recovery mode it still blocked on logo and whene I press volume down boutton and plug the usb cable it enter to the fastboot & rescue mode only
laro2202 said:
sorry for my english
please help i brick my huawei p9 plus vie-l29 after try to install a new framware it is blocked on logo an can enter only to fastboot & rescue mode
Click to expand...
Click to collapse
Questions:
-How were you installing the firmware (which method)?
-What firmware were you putting in?
-What version is your phone?
-What android version did your phone had before bricking it?
I've been there with the soft brick. I got my phone back to life by downloading a ROM, putting it into the external SD Card, created a folder named 'dload' and adding the UPDATE.APP file there, then, press vol up + vol down + power and the restore started.
One thing that's worth to mention is that the phone may not boot even with this, but you just need to put the phone on erecovery ( turn it on with vol up + power ) and wipe cache + factory reset. This will bring it back to life!
jeinnerabdel said:
Questions:
-How were you installing the firmware (which method)?
-What firmware were you putting in?
-What version is your phone?
-What android version did your phone had before bricking it?
I've been there with the soft brick. I got my phone back to life by downloading a ROM, putting it into the external SD Card, created a folder named 'dload' and adding the UPDATE.APP file there, then, press vol up + vol down + power and the restore started.
One thing that's worth to mention is that the phone may not boot even with this, but you just need to put the phone on erecovery ( turn it on with vol up + power ) and wipe cache + factory reset. This will bring it back to life!
Click to expand...
Click to collapse
thank for the message
the phone is huawei P9 Plus VIE-L29 the wrong thing that I did that I flash a data file before flashing rom and the big problem that the phone enter only to the fastboot and rescue mode like the attached picture and I thing that my phone is dead now and no way to resolve this problem
Don't worry FIND THIS VIDEO in youtube Huawei Honor 7 flashing in fastboot - DC Phoenix... BUT u should payed 15 euro for using this program but it works 100 % i used it for my VIE-L29C10 this programm flashed you phone from fastboot! GOOD luck MATE
Ok, first, don't worry, this is soft brick, which means the phone will recover, it's just a matter of flashing the right rom. Follow my steps above and make sure you turn on the phone holding the 3 buttons at the same time, once the logo appears release the power button and keep both volume keys for a few seconds and release them. That's forced update mode.
The rom is about 2.8 gigabytes and must be in dload folder on the root of your external SD.
---------- Post added at 01:40 AM ---------- Previous post was at 01:38 AM ----------
PD: Don't pay for software to get the phone back! You can do it yourself!
jeinnerabdel said:
Ok, first, don't worry, this is soft brick, which means the phone will recover, it's just a matter of flashing the right rom. Follow my steps above and make sure you turn on the phone holding the 3 buttons at the same time, once the logo appears release the power button and keep both volume keys for a few seconds and release them. That's forced update mode.
The rom is about 2.8 gigabytes and must be in dload folder on the root of your external SD.
---------- Post added at 01:40 AM ---------- Previous post was at 01:38 AM ----------
PD: Don't pay for software to get the phone back! You can do it yourself!
Click to expand...
Click to collapse
yes mate u're right first of all he should try flash his cellphone 3 button method but if it's not work he should pay for this porgamm and 100 % that programm flash his phone from rescue mode
laro2202 said:
thank for the message
the phone is huawei P9 Plus VIE-L29 the wrong thing that I did that I flash a data file before flashing rom and the big problem that the phone enter only to the fastboot and rescue mode like the attached picture and I thing that my phone is dead now and no way to resolve this problem
Click to expand...
Click to collapse
mine is the same except that the FRP is Unlock
have you found a fix yet
---------- Post added at 10:18 PM ---------- Previous post was at 10:16 PM ----------
jeinnerabdel said:
Questions:
-How were you installing the firmware (which method)?
-What firmware were you putting in?
-What version is your phone?
-What android version did your phone had before bricking it?
I've been there with the soft brick. I got my phone back to life by downloading a ROM, putting it into the external SD Card, created a folder named 'dload' and adding the UPDATE.APP file there, then, press vol up + vol down + power and the restore started.
One thing that's worth to mention is that the phone may not boot even with this, but you just need to put the phone on erecovery ( turn it on with vol up + power ) and wipe cache + factory reset. This will bring it back to life!
Click to expand...
Click to collapse
Where did you find the rom to download ?
DenPim said:
yes mate u're right first of all he should try flash his cellphone 3 button method but if it's not work he should pay for this porgamm and 100 % that programm flash his phone from rescue mode
Click to expand...
Click to collapse
Just rescued my phone by using the DC Unlocker tool.....Best 15 euros I've spent
what exactly you purchased in dc unlocker? I have the same problem as you pls help..
Jpacs said:
what exactly you purchased in dc unlocker? I have the same problem as you pls help..
Click to expand...
Click to collapse
I purchased 15 credits in DC phoenix....Read the Q&A and it will help......The program let me install a firmware using fastboot
cuzovillafan said:
I purchased 15 credits in DC phoenix....Read the Q&A and it will help......The program let me install a firmware using fastboot
Click to expand...
Click to collapse
I just restored my phone but spent 30, so annoying thnx
Sent from my VIE-L29 using XDA-Developers Legacy app
Jpacs said:
I just restored my phone but spent 30, so annoying thnx
Click to expand...
Click to collapse
Have you managed to update it
laro2202 said:
sorry for my english
please help i brick my huawei p9 plus vie-l29 after try to install a new framware it is blocked on logo an can enter only to fastboot & rescue mode
Click to expand...
Click to collapse
The device loses a Recovery Stock file that must be installed
1. Download the file Recovery Open the zip file and place the file in the Minimal ADB and Fastboot program
2. Open Minimal ADB and Fastboot
3. Connect your phone to the computer
4. Type this command (fastboot flash recovery recovery.img)
5. After installing the Recovery Stock file in your mobile phone, disconnect the cable and continue pressing the stop button until it restarts and press the stop button with the volume up button until you see Recovery and load the original ROM in the SD card
I'm sorry I can not add links to my posts a few
samy5689 said:
The device loses a Recovery Stock file that must be installed
1. Download the file Recovery Open the zip file and place the file in the Minimal ADB and Fastboot program
2. Open Minimal ADB and Fastboot
3. Connect your phone to the computer
4. Type this command (fastboot flash recovery recovery.img)
5. After installing the Recovery Stock file in your mobile phone, disconnect the cable and continue pressing the stop button until it restarts and press the stop button with the volume up button until you see Recovery and load the original ROM in the SD card
I'm sorry I can not add links to my posts a few
Click to expand...
Click to collapse
No chance to work,FRP and Bootloader is locked.This only working with unlocked Bootloader to flash img Files via Fastboot
Only DC Phoenix helps
---------- Post added at 08:34 AM ---------- Previous post was at 08:29 AM ----------
Instruction here
https://www.dc-unlocker.com/DC-Phoenix-flash-repair-tutorial
This works with locked FRP and locked Bootloader.
You have 72 Hours for 15€.
Only what you need is the right Firmware(UPDATE.APP) from your Device

Expensive Brick -Failed verification during debranding

HELP needed please
Tried to change my Vie -L09C02B133 to L09C432 - unlocked bootloader and rooted no probs so took the plunge and followed the video to debrand
After the first step re changing oeminfo again everything seemed to be ok however when my phone rebooted i got a red message saying that the phone had failed verification and may not work properly . It then asked for a password.
After a couple of reboots the phone came on but with no keyboard -
After another reboot i can't get past the Huawei logo ....
Any help appreciated
volume down & power gets me into fastboot & rescue mode bot not letting me connect to hisuite on my pc
have you got sd card? and have you got an adapter so you can use on pc?
ali3nfr3ak said:
have you got sd card? and have you got an adapter so you can use on pc?
Click to expand...
Click to collapse
I do have a SD card and can use it on the pc without the phone
cuzovillafan said:
I do have a SD card and can use it on the pc without the phone
Click to expand...
Click to collapse
power off phone, eject sd card place in pc copy the L09C432 firmware to dload folder ( marshmallow ) , place sd back in phone, hold down vol up + vol down + power buttom and it should flash the L09C432 fimware.
It should boot normally now
ali3nfr3ak said:
power off phone, eject sd card place in pc copy the L09C432 firmware to dload folder ( marshmallow ) , place sd back in phone, hold down vol up + vol down + power buttom and it should flash the L09C432 fimware.
It should boot normally now
Click to expand...
Click to collapse
My phone wont shut down.......I can restart it but it comes up with the verification error and then sticks on logo - ive tried to put the firmware - L09C02 into the dload on my sd card but still no luck ... was originally on L09C02 before running into probs with the debranding
Ok first thing , you have already changed oeminfo , so you can not roll back at this stage to your old firmware, u changed to L09C432 so you need to download L09C432B180 I think it is, might be B181, once you have downloaded that fimware, extract it, you should have a file called UPDATE.APP, remove sd card from phone , place in pc, create a folder called dload in root directory of sdcard, then copy update.app to that folder, only update.app, then hold down volume up + volume down + power button, after phone restarts and Huawei logo appears, release only the power button, a couple seconds later release volume buttons, maybe 5 to 10 seconds after the phone should automatically start updating
ali3nfr3ak said:
Ok first thing , you have already changed oeminfo , so you can not roll back at this stage to your old firmware, u changed to L09C432 so you need to download L09C432B180 I think it is, might be B181, once you have downloaded that fimware, extract it, you should have a file called UPDATE.APP, remove sd card from phone , place in pc, create a folder called dload in root directory of sdcard, then copy update.app to that folder, only update.app, then hold down volume up + volume down + power button, after phone restarts and Huawei logo appears, release only the power button, a couple seconds later release volume buttons, maybe 5 to 10 seconds after the phone should automatically start updating
Click to expand...
Click to collapse
I'll give this a go in the morning....Many thanks for your reply
cuzovillafan said:
I'll give this a go in the morning....Many thanks for your reply
Click to expand...
Click to collapse
Edit......No joy I'm afraid ....Phone completely discharged and when plugged in it boots up but sticks at logo again....Gonna try DC unlocked as described on another thread
cuzovillafan said:
Edit......No joy I'm afraid ....Phone completely discharged and when plugged in it boots up but sticks at logo again....Gonna try DC unlocked as described on another thread
Click to expand...
Click to collapse
YESSS. Got my phone back to L02C432B181 using the DC Unlocker tool... Everything seems fine.....Just waiting for full charge before I try the B362 update
cuzovillafan said:
YESSS. Got my phone back to L02C432B181 using the DC Unlocker tool... Everything seems fine.....Just waiting for full charge before I try the B362 update
Click to expand...
Click to collapse
nice :good:
cuzovillafan said:
YESSS. Got my phone back to L02C432B181 using the DC Unlocker tool... Everything seems fine.....Just waiting for full charge before I try the B362 update
Click to expand...
Click to collapse
My P9 Plus is similar to your phone's problem. Stuck on Huawei logo ang can access Fastboot only. How much did you pay for DC Unlocker? Thank you.
EDIT: Which "Operation name" did you select?
second_east said:
My P9 Plus is similar to your phone's problem. Stuck on Huawei logo ang can access Fastboot only. How much did you pay for DC Unlocker? Thank you.
EDIT: Which "Operation name" did you select?
Click to expand...
Click to collapse
I used DC Pheonix and i pay 15Euros
I flased B181 directly with DC Pheonix
zubyro said:
I used DC Pheonix and i pay 15Euros
I flased B181 directly with DC Pheonix
Click to expand...
Click to collapse
Same here.......Unable to get the update yet though....Well worth the spend to get phone working again
cuzovillafan said:
Same here.......Unable to get the update yet though....Well worth the spend to get phone working again
Click to expand...
Click to collapse
Tried the update again and success ??????

Categories

Resources