hi!
i have a doogee x5pro and after an update got a boot loop
tried to flash stock rom downladed on neeedrom.com and now my prone is totaly dead ,doesnt start at all
doest not get recognized by pc at all if i dont pres up button (battery removed ,with battery in phone nothing hapens ) and than it conect for 10-15 sec and disconect again and i cant flash with sp flash tool because it says "BROM ERROR S_FT_ENALE_DRAM_FAIL (0xFC0)
[EMI] Enabe DRAM Failed!
[HINT]:
Please check your load matches to your target which is to be downloaded."
im totaly a noob and dunno what to do please help me
(sorry if bad engish im form Albania)
Related
Xperia sp stock kernel was 12.1.A.1.201 and flashed with doomkerel v09 and keeps restarting after few minutes and in the end restarted and blank screen and no response and i connected to pc and found required driver qhsusb_dload and installed zeus flash device but nothing now please help no other cell phone i had now please please please.....
Bootloader was unlocked...
Relock bootloader and try again.... You can also use Flashtool to restore/reflash your phone... See my signature below for the link!
Flashtool does not recognize the device as it is in zeus flash device mode or point test mode nothing happening please help....
anyone has any idea if i send it to service center with no warranty what will be the procedure please help.....
It may not be off..press the back key until the phone vibrates 3 times and then connect it to flashmode.
Nothing helpful my phone bricked and nothing useful ..........
Hello ned help..
rm-1030 flashing rom 2.1.0.12 complete Done
i have two version
RM1013_059V788_2.1.0.12 and
RM1013_059V786_2.1.0.12 but still dead..
Usb detect as emerency connectivity
when im flash using rom rm1013_2.1.0.13_059V78 always stuck at rm1013_2.1.0.13_user_NON-HLOS.bin
and shown error dialog "failed using firehouse protocol"
need help..
ive try to redownload ROM.. but keep error
im sorry i cant upload picture coz need 10 posts but im using txt file
maybe the firmware you downloaded is corrupted.. where did you downloaded your firmware files? I use navifirm+ but yesterday I'm trying to redownload a rom but navifirm+ seems to be not working any more..
thaks for replay,
iv downloaded from Package Majnager .. and from this seidea.com/tag/rm-1013-2-1-0-13/
its still blank screen and just detect "emerency connecivity
first download nokia-x2-tools.v.1.2.en.exe, from the tool install drivers.. then go to your "C:\ProgramData\Nokia\Packages\Products\RM-XXX" and delete all files or move it somewhere if you don't want to delete.. and replace everything with the files that you downloaded.. and run "Lunch Nokia Care Suite" as administrator.. and flash your firmware..
thaks...
I thinks its hardware problem.. coz i have 5 different firmware and already used maximal method
change folder.. remove.. redownload.. and anythink
and my phone cant detect fastboot or recovery
btw thaks
aw.. that's too bad.. I fixed my completely dead x2 with that method though.. it has no fastboot and undetected adb but I recover it somehow, I think it's just a luck..
I have exactly same problem havent found solution yet.
I have same problem too
arisjb said:
hello ned help..
Rm-1030 flashing rom 2.1.0.12 complete done
i have two version
rm1013_059v788_2.1.0.12 and
rm1013_059v786_2.1.0.12 but still dead..
Usb detect as emerency connectivity
when im flash using rom rm1013_2.1.0.13_059v78 always stuck at rm1013_2.1.0.13_user_non-hlos.bin
and shown error dialog "failed using firehouse protocol"
need help..
Ive try to redownload rom.. But keep error
im sorry i cant upload picture coz need 10 posts but im using txt file
Click to expand...
Click to collapse
Remove battery from device atleast 1min
Insert battery
Start device in bootloop and if not start only connect to PC
Start Nokia care suite >product software > open product> select device and flash
jepr0x1011 said:
aw.. that's too bad.. I fixed my completely dead x2 with that method though.. it has no fastboot and undetected adb but I recover it somehow, I think it's just a luck..
Click to expand...
Click to collapse
My Nokia X2 had also give completely dead. I tried to Flash stock ROM in it via Nokia care suite and which I've even done previously however this time my phone had gone completely blank and does not even go to recovery mode. It has gone completely unresponsive. Please help me on this.
Hello guys
My xperia zr device got hard bricked after flashing by twrp recovery official edition
I made a restart then the device got dead.
1-I tried to press power button the device viberated but nothing else.
2-I tried to connect the device using xperia companion but still nothing.
3-My device only detected as S1 Service !!!.
4-I tried to flash it using S1 tool using the emergency mode by the test point after disassemble the motherboard.
but the pc got hanged then I got this error (
llbug: [\\?\USB#Vid_0E0F&Pid_0001#6&1636b011&0&2#{a5dcbf10-6530-11d2-901f-00c04fb951ed}] open error: "Access is denied")
anybody can help?
After lock bootload i got bootloop and Show :
Red state "restart every 5 second"
can't go to recovey or turn off
it only restart
I tried SP flash tool but got error as soon as click download. And error is ;
ERROR: STATUS_BROM_CMD_SEND_DA_FAIL_(OxC0060003).
another thing i noticed is when phone is usb connected i keep hearing sound for usb conenct and disconnect every 10 seconds.
looks like phone is not connecting well to PC.
I installed all posisble drivers for win 10. I installed mediatek driver, Oppo, Realme drivers etc
Please please please HELP Meee
Hint: Replace in this thread's title "Help Pleaseeeeee" by "How to fix bootloop"
thankx2u said:
After lock bootload i got bootloop and Show :
Red state "restart every 5 second"
can't go to recovey or turn off
it only restart
I tried SP flash tool but got error as soon as click download. And error is ;
ERROR: STATUS_BROM_CMD_SEND_DA_FAIL_(OxC0060003).
another thing i noticed is when phone is usb connected i keep hearing sound for usb conenct and disconnect every 10 seconds.
looks like phone is not connecting well to PC.
I installed all posisble drivers for win 10. I installed mediatek driver, Oppo, Realme drivers etc
Please please please HELP Meee
Click to expand...
Click to collapse
Try to format your bootloader using sp flash tool and reflssh it
hello guys , i tried to flash the firmware on a Alcatel 4047F using SP Flash Tool but it gives me this error "S_AUTH_HANDLE_IS_NOT_READY" .
i have checked already the program errors and solutions for them and the problem is that to solve it i will need a Auth or DA file for the phone and i didnt find it anywhere "You'll need an Auth (*.auth) or custom Download Agent (DA) file for the device to proceed with SP flash tool" .
If someone could share the files to fix this i would really apreciate it
every firmware tried gives that error , which didnt happen before
now the phone doesnt turn on even to recovery mode , if it is connected to pc i hear the sound of the usb but the phone isnt shown on pc and looks like it keeps rebooting because i keep listening to the sound all the time