WIFI Wont Turn On - T-Mobile Galaxy Note 4 Q&A, Help & Troubleshooting

I've been trying to flash a custom ROM on my Note 4 for about a day now and every ROM I flash the WIFI wont turn on I will do my best to list in full the steps I've taken to do everything.
Started by trying to use Heimdall Suite to flash TWRP twrp-3.0.2-0-tbltetmo.img but it failed to download my device's PIT file. After some searching I told to use ODIN in place of Heimdall Suite Downloaded ODIN Odin3 v3.12.3 used it to flash twrp-3.0.2-0-trltetmo.img.tar. This seamed to work I have TWRP installed now so far as I can tell.
I downloaded CMRemix (CMRemix_trltetmo_MM.6.0.1_r61.v17.8_20160820-112925.zip) and flashed it after doing a full wipe. It looked like it installed correctly but during the initial setup it fails to turn on wifi.

LoadingSA said:
I've been trying to flash a custom ROM on my Note 4 for about a day now and every ROM I flash the WIFI wont turn on I will do my best to list in full the steps I've taken to do everything.
Started by trying to use Heimdall Suite to flash TWRP twrp-3.0.2-0-tbltetmo.img but it failed to download my device's PIT file. After some searching I told to use ODIN in place of Heimdall Suite Downloaded ODIN Odin3 v3.12.3 used it to flash twrp-3.0.2-0-trltetmo.img.tar. This seamed to work I have TWRP installed now so far as I can tell.
I downloaded CMRemix (CMRemix_trltetmo_MM.6.0.1_r61.v17.8_20160820-112925.zip) and flashed it after doing a full wipe. It looked like it installed correctly but during the initial setup it fails to turn on wifi.
Click to expand...
Click to collapse
Cm 12 & Cm13 required stock 5.1.1 lillipop bootloader and modem
If you are on mm 6.0.1 the wifi wont turn on cuz modem & bl is not compatible.

I am having the same issue with wifi not turning on. How do I know which bootloader and modem are required? Where would I get these?

Trex888 said:
Cm 12 & Cm13 required stock 5.1.1 lillipop bootloader and modem
If you are on mm 6.0.1 the wifi wont turn on cuz modem & bl is not compatible.
Click to expand...
Click to collapse
I wonder if someone could expand on how I could fix this? I'm still in my learning stages and I have to admit, sadly I don't know exactly how to tackle this one.
Edit:
I was able to solve this issue by reading this post http://forum.xda-developers.com/showpost.php?p=69480388&postcount=13835 and flashing the 2 files in the link provided.

LoadingSA said:
I wonder if someone could expand on how I could fix this? I'm still in my learning stages and I have to admit, sadly I don't know exactly how to tackle this one.
Edit:
I was able to solve this issue by reading this post http://forum.xda-developers.com/showpost.php?p=69480388&postcount=13835 and flashing the 2 files in the link provided.
Click to expand...
Click to collapse
This also solved my problem after trying many ROMs and none of them would turn on wifi, it was only available on stock. after updating the bootloader and modem to dok2 everything started working

Related

[Q] Galaxy S i9000 softbricked; won't enter recovery or reflash from download mode

Similar to Masterslackers issue.
The phone was originally a stock Optus Éclair 2.1. About 6 months ago I decided to customize the i9000 with a custom Froyo 2.2.1 Rom (Doc's Rom Docs_XWJS3_Wipe-v9_1) from “The ROM Kitchen”. It worked really well and was much faster and responsive..
Yesterday, I decided to look at a move to Gingerbread and cook another ROM @ the ROM Kitchen, this time a Gingerbread 2.3.4 iteration.
The phone was rooted so I used Rom Manager to get into recovery mode where I could flash my new, Doc's JVR_No_Wipe-v8-00-08-22-10-09-4e6a8e4e86718.zip Rom.
All seemed to go well, but after the Flash, as the phone booted the first screen became filled with 100s of random coloured lines, then it transitioned to the normal Samsung start animation, but soundless.
After booting, I noticed that I no longer had a notification bar where battery, time, signal strength etc. was normally displayed atop the screen. I tried several different launchers to see if that was the issue, but to no avail. I tried to enable the notification bar using Go Launchers gesture setting (no go)
I tried rebooting the phone over and over, the notification bar would not return.
I was starting to lament my decision to flash when the following occurred.
I tried to re-enter recovery mode via ROM Manager to install a different ROM, but the phone bypassed it and then hung @ the Samsung I9000 logo screen. I then had to power the phone off before it would reboot into its UI. I could no longer reach recovery mode by any means.
Because I was getting nowhere and I had read that after flashing a new rom, root would often be lost, so I tried rerooting with "XXJVP-Complete-Rooting-Package" from
http://androidadvices.com/how-to-root-galaxy-s-on-android-2-3-4-xxjvp-firmware/ This also failed but it has also left me with a soft bricked phone.
The phone will not boot up or boot into recovery now, however It would still boot into (3 button) download mode.
I have tried various versions of Odin from v1.0 to v4.28 to ReFlash the phone back to life but with no success yet.
Using Odin, the phone hangs with no sign of progress and reports the following when left for 30minutes or so.
<ID:0/003> Added!!
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
Anyone have any suggestions that might help to get the phone back.
Thanks, TeZ
So you didn't flash stock gingerbread before flashing custom rom? so you should first flash stock jvr and do hard reset after booting. Then you are safe to flash cwm capable kernel and custom rom.
For the odin problems, maybe you have kies running in background? Kill all kies processes and try again.
And I'd suggest reading all guides found in romkitchen thread..it saves lots of trouble. Hope that can fix your phone
Sent from my GT-I9000 using xda premium
Agree with above post, if you have Klies on your pc/laptop uninstall it, and re download the drivers, i have a good 2.3.4 tutorial and root 2.3.4 tutorial, both with Odin, let me know if interested. Also if you have heimdall installed then uninstall it also.
After you unistalled Kies (or at least stop it) and installed the drivers , pick a stock rom with bootloader from Ramad collection http://forum.xda-developers.com/showthread.php?t=1102881 .
I prefer Odin 1.82.
If you still unable to flash your phone, please follow steps from this guide to see how can debrick your phone.
http://forum.xda-developers.com/showthread.php?t=1134975
Good luck
Thanks for that, I did install kies after I bricked it, in the hope (probably missguided) that it would somehow help. Uninstalling
bigmadpete said:
Agree with above post, if you have Klies on your pc/laptop uninstall it, and re download the drivers, i have a good 2.3.4 tutorial and root 2.3.4 tutorial, both with Odin, let me know if interested. Also if you have heimdall installed then uninstall it also.
Click to expand...
Click to collapse
Thanks for your input, right now i need all the help I can get, hadn't heard of heimdall before. I guess its one more thing I could try if all else fails. But right now I'm going to try a few more conventional things with odin, like flash a stock rom etc.
DSGE said:
After you unistalled Kies (or at least stop it) and installed the drivers , pick a stock rom with bootloader from Ramad collection http://forum.xda-developers.com/showthread.php?t=1102881 .
I prefer Odin 1.82.
If you still unable to flash your phone, please follow steps from this guide to see how can debrick your phone.
http://forum.xda-developers.com/showthread.php?t=1134975
Good luck
Click to expand...
Click to collapse
Your post looks promising, I'm going to try this method out and see where it leads. I'll reply back with the outcome, many thanks
No problem. Try this option if you like http://www.theandroidsoul.com/xxjvp-android-2-3-4-firmware-galaxy-s-install-and-download/
And then this to root
http://www.theandroidsoul.com/root-xxjvp-firmware/
bigmadpete said:
No problem. Try this option if you like http://www.theandroidsoul.com/xxjvp-android-2-3-4-firmware-galaxy-s-install-and-download/
And then this to root
http://www.theandroidsoul.com/root-xxjvp-firmware/
Click to expand...
Click to collapse
Thanks for the info, running out of time today, will try for tomorrow
When moving from a froyo (2.2) rom to gingerbread, (2.3), you need the gingerbread bootloaders or you'll get all sorts of crap when turning on your phone (ie what you have).
Use odin to flash back to froyo, or flash a gingerbread firmware that comes with bootloaders. (I would recommend going back to froyo first to make sure everything is ok, since flashing bootloaders is a bit risky, as messing it up can permanently brick your phone)
cobrasixtysix said:
Thanks for your input, right now i need all the help I can get, hadn't heard of heimdall before. I guess its one more thing I could try if all else fails. But right now I'm going to try a few more conventional things with odin, like flash a stock rom etc.
Click to expand...
Click to collapse
DSGE said:
After you unistalled Kies (or at least stop it) and installed the drivers , pick a stock rom with bootloader from Ramad collection http://forum.xda-developers.com/showthread.php?t=1102881 .
I prefer Odin 1.82.
If you still unable to flash your phone, please follow steps from this guide to see how can debrick your phone.
http://forum.xda-developers.com/showthread.php?t=1134975
Good luck
Click to expand...
Click to collapse
Ok, here's where I'm at:
For the sake of simplicity I will detail what gave positive results rather than a tirade of what didn't.
Uninstalled Kies, rebooted
As instructed, went to:
http://forum.xda-developers.com/showthread.php?t=1102881
downloaded: Odin v1.82
downloaded: Gingerbread 2.3.3 (Australia and New Zealand)
XWJVN/XXJVQ/XSAJV5/Sbl (CSC: XSA): Download (150 MB) (Build date: Sun Jul 10 11:30:54 KST 2011)
Loaded up Odin and followed instructions.
Flash went ahead as normal and I now have a working phone again, thanks to you DSGE, I'm a very happy man
So I now have Gingerbread 2.3.3 installed and running.
My only issue's now is, that.
1. Half my apps dont work now or force close even after a reinstall.
2. Some apps won't install at all IE; my fav launcher; Go Launcher
3. I no longer have root access so Rom Manager and Titanium backup wont work.
4. My Backup Pro, works after I rewrote the correct path to the External Sd, but do I want to do that just yet? and just how much data should I reinstate so I don't corrupt the new system?
What should I do now?
Install busybox?
do a hard reset?
Flash a different Rom that will work for me?
Thanks so very much for all the good advise.
Cheers
First root the phone, then either a different rom, or format system and re install 2.3.3 or which ever u just installed, i think ure apps are not working due to the phone needing a wipe/reset and cache cleared from clockwork recovery
bigmadpete said:
First root the phone, then either a different rom, or format system and re install 2.3.3 or which ever u just installed, i think ure apps are not working due to the phone needing a wipe/reset and cache cleared from clockwork recovery
Click to expand...
Click to collapse
OK, latest update:
Everything is working fine including all my progs.
Like you say, I just need to root it now.
Can you point me to the correct files to root?
Thanks
http://www.addictivetips.com/mobile...t-samsung-galaxy-s-i9000-with-a-single-click/
or
http://androidadvices.com/how-to-root-samsung-galaxy-s-gt-i9000/
Read carefully friend
bigmadpete said:
http://www.addictivetips.com/mobile...t-samsung-galaxy-s-i9000-with-a-single-click/
or
http://androidadvices.com/how-to-root-samsung-galaxy-s-gt-i9000/
Read carefully friend
Click to expand...
Click to collapse
Seems to relate to 2.1 to 2.2.1 didn't see any mention of 2.3.3. I'm afraid I'll stuff the phone if I use the old root files.

Flashing troubles on my I9001

Hello everybody,
I've been following some posts around the forum for some time now.
So I decided to flash my Samsung Galaxy S + with the newest stock firmware.
I first tried Odin, but that was no succes because VirtualBox couldn't handle it and just crashed when it started to upload the roms into my phone.
So it was bricked first, but got it back up and running.
I'm using linux as my OS, so of course I found Heimdall.
This seemed a nice tool, but I found out that the package format needs to be else then how the stock roms are delivered.
At last I tried to flas using the dd method.
I did the command dd if=...img of=dev/block/mmcblk0p.. bs=4096 for all partition images.
I managed to start the flashed roms. Only I found out that after installing some apps and after a few reboots the system starts to get faulty.
All of a sudden Play Store doesn't install apps anymore "Package Invalid" error, and for some reason also after each reboot more apps start to dissappear (get replaced by sd-card icon but unable to open or reïnstall).
Also I did a factory reset after dd'd the images into my phone, cause that's what everybody recommends.
The roms I've tried so far were XXKQB and XXKP1, both with the same issues.
The original firmware which came with my phone is: XXKPG.
Hopefully somebody can point me in the right direction in getting a newer rom onto my pda.
Greetings PsychoGame
I suggest you use a PC, im sure you will find one somewhere, friend/neighbour/relative. Then use Odin to flash.
Odin firmwares
Sammobile.com You should find I9001 firmware here
http://forum.xda-developers.com/showthread.php?t=1102881 Not sure if compatible with I9001
Or if your persistent have you tried here. **Check if compatible** If its an older firmware, connect to Kies and it should update to the latest.
JUST NOTICED THE I9001 CHECK THAT THE FIRMWARE IS COMPATIBLE
I agree with Talon, use ODIN on a windows-based machine... In any case you can always install windows on a different partition, but it's not worth it. For me the whole flashing process only lasted for 4 minutes, so just grab a PC somewhere and install it...
I also recommend KQE insted of KQB as the wifi is fixed

[Q] bricked N7000. how to get working again

I tried upgrading my international N7000 to CM10.3 following the instructions in
http://wiki.cyanogenmod.org/w/Install_CM_for_n7000
but now the phone won't even boot into the recovery, all it shows is
Samsung
GALAXY Note
GT-N7000
/ \
/ | \
/--*-\
When i tried flashin from my Mac iusing Heimdall,
the download finished on the mac, but on the N7000
it still showed the blue line etc. I waited a lng time and tried
rebooting, but got the above.
Re-flashing in Heimdall had no effect.
I then tried flashing
hardcore-speedmod-ics-recovery-n7000.tar
using Odin 3.185 from my VMwars Fusion XP install,
and that seemed to finish ok, but no luck either.
I looked for the latest CWM 6.0.4.3 recovery, but I cannot find any
odin-flashable format for it, and of course I cannot use the sdcard
as I cannot even boot into any recovery as is.
Can anyone suggest next steps?
sejtam said:
I tried upgrading my international N7000 to CM10.3 following the instructions in
http://wiki.cyanogenmod.org/w/Install_CM_for_n7000
but now the phone won't even boot into the recovery, all it shows is
Samsung
GALAXY Note
GT-N7000
/ \
/ | \
/--*-\
When i tried flashin from my Mac iusing Heimdall,
the download finished on the mac, but on the N7000
it still showed the blue line etc. I waited a lng time and tried
rebooting, but got the above.
Re-flashing in Heimdall had no effect.
I then tried flashing
hardcore-speedmod-ics-recovery-n7000.tar
using Odin 3.185 from my VMwars Fusion XP install,
and that seemed to finish ok, but no luck either.
I looked for the latest CWM 6.0.4.3 recovery, but I cannot find any
odin-flashable format for it, and of course I cannot use the sdcard
as I cannot even boot into any recovery as is.
Can anyone suggest next steps?
Click to expand...
Click to collapse
1st things 1st. Why would u use heimdall or odin? And what is your current ROM before trying to flash CM 10.3, was it stock? You should have looked for CWM recovery or Philz safe kernels as base when doing ROM flashing ESPECIALLY custom roms. From what you said, then can you still boot into download mode? I have no knowledge of heimdall so just download Stock Firmware, flash it with odin and see if you can boot your N7000 first.
The worst case scenarios is you are experiencing emmc bug-brick. go to the thread and read carefully to deduce your type of 'brick' and find solutions there. Good Luck.
I was on a stock 4.0.4 (but rooted). I originally tried flashing the cwm from the sd card, but after starting to load it it also just hung,
so I looked for an alternative..
I found a post on stockroms (http://forum.xda-developers.com/showthread.php?t=1424997) but the links all point to hotfile.com. which my browser says it cannot find. is hotfile dead? Is there an alternative?
sejtam said:
I was on a stock 4.0.4 (but rooted). I originally tried flashing the cwm from the sd card, but after starting to load it it also just hung,
so I looked for an alternative..
I found a post on stockroms (http://forum.xda-developers.com/showthread.php?t=1424997) but the links all point to hotfile.com. which my browser says it cannot find. is hotfile dead? Is there an alternative?
Click to expand...
Click to collapse
Go to sammymobile.com if I'm not wrong. Download the stock firmware there. Rooted but do u have cwm installed? Rooted doesn't mean you have cwm installed.
Sent from my GT-N7000 using XDA Free mobile app
same problem
Jackwu696 said:
Go to sammymobile.com if I'm not wrong. Download the stock firmware there. Rooted but do u have cwm installed? Rooted doesn't mean you have cwm installed.
Sent from my GT-N7000 using XDA Free mobile app
Click to expand...
Click to collapse
i have the same problem , only mine loads into the recovery menu , ive tried finding a working odin to nstall it back to factory.
when i had this problem last night , i wasnt sure what i done but i managed to install a custom rom and that worked but now i seem to be getting status 7 error ,
my computer wont recognise my phone so i cant do anything that way . any ideas or links to solutions will be appreciated
i have the same problem
conanbrapp said:
i have the same problem , only mine loads into the recovery menu , ive tried finding a working odin to nstall it back to factory.
when i had this problem last night , i wasnt sure what i done but i managed to install a custom rom and that worked but now i seem to be getting status 7 error ,
my computer wont recognise my phone so i cant do anything that way . any ideas or links to solutions will be appreciated
Click to expand...
Click to collapse
I'm sorry so did u succeed or did you not succeed in installing the custom rom? If your custom rom boots fine then all u need is to search for solving status 7 error thread. My advice to all noobs is to always try n avoid installimg anything except stock rom in odin. Always read and re read before flashing anything that's beyond your knowledge. Basic knowledge of flashing cusroms is :
1. ALWAYS make sure you're on SAFE and COMPATIBLE KERNEL. Most rom threads ALWAYS Include threads/links to a specific recovery/kernel to use. Read n RE READ that.
2. Wipe everything IN RECOVERY mode before flashing a rom.
Sent from my GT-N7000 using XDA Free mobile app
fixed miine
Jackwu696 said:
Go to sammymobile.com if I'm not wrong. Download the stock firmware there. Rooted but do u have cwm installed? Rooted doesn't mean you have cwm installed.
Sent from my GT-N7000 using XDA Free mobile app
Click to expand...
Click to collapse
Jackwu696 said:
I'm sorry so did u succeed or did you not succeed in installing the custom rom? If your custom rom boots fine then all u need is to search for solving status 7 error thread. My advice to all noobs is to always try n avoid installimg anything except stock rom in odin. Always read and re read before flashing anything that's beyond your knowledge. Basic knowledge of flashing cusroms is :
1. ALWAYS make sure you're on SAFE and COMPATIBLE KERNEL. Most rom threads ALWAYS Include threads/links to a specific recovery/kernel to use. Read n RE READ that.
2. Wipe everything IN RECOVERY mode before flashing a rom.
Sent from my GT-N7000 using XDA Free mobile app
Click to expand...
Click to collapse
im not Sure what i did , i unbricked (soft) and successfully installed kitkat not sure exactly how but it worked.... still have root too ... had and error about needing to wipe data for suib i think but thats the only fallback i fell into
conanbrapp said:
im not Sure what i did , i unbricked (soft) and successfully installed kitkat not sure exactly how but it worked.... still have root too ... had and error about needing to wipe data for suib i think but thats the only fallback i fell into
Click to expand...
Click to collapse
If you're able to boot up properly n prompted to wipe, then do it. But do it in recovery not on device.
Ok, I downloaded one of the stock kernels for my internatinal N7000, but flashing that with Odin 3.185 hangs about 3/4 through (has now been
sitting there for >60 mins).
Looks like I am screwed?
The file I found is KIES_HOME_N7000XXLT4_N7000OXALT4_1103517_REV02_user_low_ship.tar.md5
I f I wanted to try flashing this with Heimdall, I'd need to know partition numbers I think
Where can I get those?
Or should I get another file?
sejtam said:
Ok, I downloaded one of the stock kernels for my internatinal N7000, but flashing that with Odin 3.185 hangs about 3/4 through (has now been
sitting there for >60 mins).
Looks like I am screwed?
The file I found is KIES_HOME_N7000XXLT4_N7000OXALT4_1103517_REV02_user_low_ship.tar.md5
I f I wanted to try flashing this with Heimdall, I'd need to know partition numbers I think
Where can I get those?
Or should I get another file?
Click to expand...
Click to collapse
Before that, do u have KIES installed? KIES is NOT compatible with odin and will cause potential trouble. So is some firewall and antivirus apps. You need to disable all of them before using odin. Please search the thread http://www.sammobile.com/firmwares/ for stock rom site.
Sent from my GT-N7000 using XDA Free mobile app
Ok. I downloaded two stock roms from sammobile:
[email protected] 1 mathias staff 808649674 May 9 10:53 N7000XXLT5_N7000MBCLT1_MBC.zip
[email protected] 1 mathias staff 750466356 May 9 10:50 N7000XXLRL_N7000OXELR5_MBC.zip
but both fail with some (unreadable, apparently character set issue) error under ODIN.
I found this:
http://droidangel.blogspot.sg/2012/01/samsung-galaxy-note-gt-n7000-all.html
which shows how to do a full flash , including PIT file, but the links again go to hotfile which seems to be down.
http://hotfile.com/dl/140099962/b9e0d63/Q1-20110914_16GB.pit.rar.html
Where can I get a) separate
CODE_N7000xxxxx_CLxxxxxxx_REVxx_user_low_ship.tar.md5
MODEM_N7000xxxxxx_REV_00_CLxxxxxx.tar.md5
GT-N7000-CSC-MULTI-xxxxxx.tar.md5
and the PIT file?
sejtam said:
Ok. I downloaded two stock roms from sammobile:
[email protected] 1 mathias staff 808649674 May 9 10:53 N7000XXLT5_N7000MBCLT1_MBC.zip
[email protected] 1 mathias staff 750466356 May 9 10:50 N7000XXLRL_N7000OXELR5_MBC.zip
but both fail with some (unreadable, apparently character set issue) error under ODIN.
I found this:
http://droidangel.blogspot.sg/2012/01/samsung-galaxy-note-gt-n7000-all.html
which shows how to do a full flash , including PIT file, but the links again go to hotfile which seems to be down.
http://hotfile.com/dl/140099962/b9e0d63/Q1-20110914_16GB.pit.rar.html
Where can I get a) separate
CODE_N7000xxxxx_CLxxxxxxx_REVxx_user_low_ship.tar.md5
MODEM_N7000xxxxxx_REV_00_CLxxxxxx.tar.md5
GT-N7000-CSC-MULTI-xxxxxx.tar.md5
and the PIT file?
Click to expand...
Click to collapse
Of course you fail... When using ODIN, U should have downloaded the .tar. if you downloaded a zip. then unzip it first to get the tar file, then you flash it with odin. All requests are included in the stock.tar And PLEASE DO NOT Play with PIT files if you don't know what you are doing.
So now what you need to do is. :
1. DISABLE KIES (Uninstall it better), Your firewall, antivirus.
2. Install CORRECT Samsung USB driver. (Search keyword "download samsung N7000 usb drivers")
3. Unzip your zip file and extract the tar.file.
4. Run ODIN as Administrator (Right click/run as)
5. Go to download mode. connect your device to Pc/laptop.
6. Wait until Odin detects your device, click AP/PDA and choose the tar file you extracted.
7. DO NOT tick partition.
8. Let it run
Of course I unzipped the zip to get a SINGLE .tar.md5, but flashing that fails on factoryfs about 3/4 through. consistently.
sejtam said:
Of course I unzipped the zip to get a SINGLE .tar.md5, but flashing that fails on factoryfs about 3/4 through. consistently.
Click to expand...
Click to collapse
Try updating your odin. Use the newest vers. And try and read this https://www.google.com/url?q=http:/...ds-cse&usg=AFQjCNGd2e3iG5hkDeo0KyAjGuCSfQSLUw . If All fails then it's a confirmed SUPER-BRICK and there's nothing except samsung service centre can help you now... Sorry for not being able to help more..
Thanks. That led me to
http://forum.xda-developers.com/showthread.php?t=1656635
where I found the PIT file, but for ROMs pointed to http://forum.xda-developers.com/showthread.php?t=1530501
which again points to hotfile and fileserve.com , which (besides being under maintenance) says
FileServe can only be used to download and retrieve files that you have uploaded personally.
which makes it useless for finding ROMs...
sejtam said:
Thanks. That led me to
http://forum.xda-developers.com/showthread.php?t=1656635
where I found the PIT file, but for ROMs pointed to http://forum.xda-developers.com/showthread.php?t=1530501
which again points to hotfile and fileserve.com , which (besides being under maintenance) says
FileServe can only be used to download and retrieve files that you have uploaded personally.
which makes it useless for finding ROMs...
Click to expand...
Click to collapse
His link to ROMS were basically the same ones you can download at sammobile.

[Q] Odin just won't flash at all

Hi guys, my problem is as stated in the title, Odin just will not let me flash my Note. My note is currently on (older) CM12 NightOwl alpha 5 ROM maintained by @bauner at this thread and wanting to upgrade to his newest beta release. Since it has no working recovery I have to flash a working one via Odin, I had problems with Odin not recognising the Note, so I reinstalled Kies and it appears it was a driver issue, so that being solved I tried flashing the stock ROM for my phone with Odin saying it failed, then attempted flashing Philz Touch (3 different versions) and failed those, tried adding the correct pit file and reattempted all previous recoveries and the ROM and those failed too. Since the NightOwl ROM is in .zip format I only assume I can install from recovery, oh I also tried flashing a kernel he supplied in the thread. I've also tried various Odin versions.
Any ideas?
Guess these forums aren't very active nowadays?
1st make sure there are no kies processes running in task manager.
Then flash philz XXLTA tar kernel file using odin.
nokiamodeln91 said:
1st make sure there are no kies processes running in task manager.
Then flash philz XXLTA tar kernel file using odin.
Click to expand...
Click to collapse
Thanks for the reply. I've managed to flash my phone now but I did it on my old laptop, so the problem appears to be with my PC. I'm not sure what it is though, the only difference I could figure is that I was using a USB 3.0 port on my PC, is there any known issues with that? Everything else that could effect it is the same. Both had the same drivers, both didn't have Kies running, I even used the same cable, the port I was using on the PC is functional and transfurs data to other devices correctly... This has got me clueless.

help please!

Hi everyone i desperately need some help, i had a rooted note 4 gave it to my cousin in greece, he just came back and i told him i would update it, i downloaded tekx"s rom and installed i did a full wipe as usual, after it installed the phone kept on rebooting over and over again, so i thought maybe i had to update the firmware, i tried doing that but i keep getting a fail message i cant update anything. so i rerooted the phone tried updating the firmware again and still getting a fail message. so now i dont have anything on the phone i am only able to go into recovery or down load mode, cant go into any type of settings on the phone incase i forgot to unlock something in there. i've looked everywhere on the net and cant find any type of solution, can someone help me out please? Thank you
panitsos said:
Hi everyone i desperately need some help, i had a rooted note 4 gave it to my cousin in greece, he just came back and i told him i would update it, i downloaded tekx"s rom and installed i did a full wipe as usual, after it installed the phone kept on rebooting over and over again, so i thought maybe i had to update the firmware, i tried doing that but i keep getting a fail message i cant update anything. so i rerooted the phone tried updating the firmware again and still getting a fail message. so now i dont have anything on the phone i am only able to go into recovery or down load mode, cant go into any type of settings on the phone incase i forgot to unlock something in there. i've looked everywhere on the net and cant find any type of solution, can someone help me out please? Thank you
Click to expand...
Click to collapse
Flash latest stock firmware in odin .
Once odin shows PASS go to stock recovery and do factory reset and wait 15 minutes to boot.
Do you have N910T tmobile note 4 ?
Link below for n910t latest firmware.
Extract the file and flash using odin choose AP
https://www.androidfilehost.com/?fid=385035244224408290
Trex888 said:
Flash latest stock firmware in odin .
Once odin shows PASS go to stock recovery and do factory reset and wait 15 minutes to boot.
Do you have N910T tmobile note 4 ?
Link below for n910t latest firmware.
Extract the file and flash using odin choose AP
https://www.androidfilehost.com/?fid=385035244224408290
Click to expand...
Click to collapse
i tried the cog2 the dok firmware nothing it fails all the time. if i try flashing this newer firmware and it works by some chance then i'm worried i wont be able to get a rom to work because from what i've seen most roms are cog2 or doc 6
panitsos said:
i tried the cog2 the dok firmware nothing it fails all the time. if i try flashing this newer firmware and it works by some chance then i'm worried i wont be able to get a rom to work because from what i've seen most roms are cog2 or doc 6
Click to expand...
Click to collapse
yes i have a tmboile note 4

Categories

Resources