Xperia T dead. Help please... - Sony Xperia T, TL, TX, V

It's not my first time to flashing roms. But this time i think phone dead. Here is the story: I installed cm12 and wipe system flash cm 14 adn finally today i flashed cm13 and i loved it. But when i opened file explorer i see internal storage is 2gb(before flashing it is 10gb). When i opened TWRP 3.0.2 i see another legacy sd partition. I think if i will format this partition i can get 10gb internal storage back. And i formatted legacy sd using twrp. But when i push reboot system now phone turned off and never go back. no any red or green light. I'm sure phone have min 50% charge and battery new(not battery problem). I tried remove battery but it is not work. When connect it to pc see this on bottom right corner ''QHSUSB_DLOAD'' and no driver found and no any light on phone. What can i do now? Flash tool and Emma dont recognize device.

Elshan_Nurmammadov said:
It's not my first time to flashing roms. But this time i think phone dead. Here is the story: I installed cm12 and wipe system flash cm 14 adn finally today i flashed cm13 and i loved it. But when i opened file explorer i see internal storage is 2gb(before flashing it is 10gb). When i opened TWRP 3.0.2 i see another legacy sd partition. I think if i will format this partition i can get 10gb internal storage back. And i formatted legacy sd using twrp. But when i push reboot system now phone turned off and never go back. no any red or green light. I'm sure phone have min 50% charge and battery new(not battery problem). I tried remove battery but it is not work. When connect it to pc see this on bottom right corner ''QHSUSB_DLOAD'' and no driver found and no any light on phone. What can i do now? Flash tool and Emma dont recognize device.
Click to expand...
Click to collapse
Hi! i have de same problem right know... i format de lagacy sd and now is bricked like your phone.
Did you solve IT?

Hi. Generally when the phone doesn't respond, you had to consider it hard bricked, and there's no solution that you can apply without putting the hands on the Hardware. My advice is to try let it charging for 24+ hours and see if something happens. For example if the led turns on, probably you are in soft brick and you can bring it back to life. There's a tread here in XDA explaining the importance of charging cycles for the late 2012 Sony devices.
In my case I couldn't flash nothing on xperia T until I haven't let it charging for 25 hours straight. Then I was able to bring it back to life.
Hope you can do the same. In any case, good luck.

I might be reckoning wrong, but I believe I've recovered my T several times using stock firmware in such case.. Then go again with CM or whatever.
landerxxx said:
Hi! i have de same problem right know... i format de lagacy sd and now is bricked like your phone.
Did you solve IT?
Click to expand...
Click to collapse

MaliSimo said:
Hi. Generally when the phone doesn't respond, you had to consider it hard bricked, and there's no solution that you can apply without putting the hands on the Hardware. My advice is to tryif something happens. For example if the led turns on, probably you are in soft brick and you can bring it back to life. There's a tread here in XDA explaining the importance of charging cycles for the late 2012 Sony devices.
In my case I couldn't flash nothing on xperia T until I haven't let it charging for 25 hours straight. Then I was able to bring it back to life.
Hope you can do the same. In any case, good luck.
Click to expand...
Click to collapse
after+ 12hr of charging i see blinked red every 2 mint .... what can ido for this ??plz help sorry for bad english

Sorry for the late reply. Its a good sign, so now you know your phone its not hard bricked. There's hope!!! Let it charge for other 12+ hours and you should see the blinking red led becoming continuous. Then you could try flashing a kernel and a custom recovery, if it works you can try flashing a ROM. Alternatively you can try to flash a stock ROM via flashtool.
Anyway now you know the phone it's alive, keep trying and you will able to bring it back to life.

Many thanks for you pro.... but usb not recognized or appear like "Qualcomm driver ..any advice ....any way I could leave it in charger and try again....Thanks for ur reply...

Maybe you can try, if you didn't already, to install the latest Sony flashtool, browse the installation folder, search for drivers and use the installation tool to reinstall the blue board 3 drivers (if you are using win 10 you may need to disable the driver signature to install the drivers properly).
I got the same problem with my Xpetia T, here I will report the steps I followed:
1. The phone didn't respond to any command, even to hard reset (pressing power button and volume + for 10s until you don't feel 3 vibrations, not recommended to do that, but I was a little frustrated).
2. I let it charging for a bit then I tried to flash a stock ftf file ( Installing the drivers just how I explained at the beginning) via flashtool. I managed to put the phone in flash mode but the procedure failed when the program started to flash the system file.
3. So I let it charge for 25h: in the first 5h no led showed up, then blinking red led, then continuous red led and finally continuous green led.
4. After that I retried to flash a stock ROM via flash tool but the procedure failed again when it was flashing the file system.
5. So I made a desperate try: I flashed all partitions but system via flash tool, then I extracted the system partition opening the ftf file with a zip manager and I used the fastboot functionality in flashtool to flash the system partition.
6. After I did that, I didn't see any improvement and I decided to put the phone in charge again and..... The kernel battery charging symbol appeared!!!
7. I let the phone charge over night then I booted it up! He booted in provisory mode and I managed to turn on USB debug and I gave permissions to my PC.
8. Then I installed TWRP via adb and so Linage 14.1 custom ROM.
The only problem I found it's my battery is practically dead, so I will try to replace it by my self in near future (this phone as known battery issues)
This is the method I followed, I don't know if is equally good for your case but I Hope this steps somehow help you.

Related

Captivate dead? Boot to blank black screen

Need some help trying to figure out how to make my Captivate turn on...I press power and get the AT&T slash screen and then the galaxy s logo loads for about 3 minutes and goes to blank dark screen with the capacitive buttons lit. this is not good because my **** won't boot into recovery either
You should flash to stock then...pull battery, hold volume buttons and plug in usb with odin loaded and ready on the computer. There's plenty of threads to help you out
Sent from my phone so excuse the spelling errors
Funnily enough... My phone just did that too. I was installing Mort Widget and it just totally bricked...
I'm rather p!ssed at this...
Course this was after it deleted all my email accounts and SMS.
What you'll need.
Odin (search or look in any of the ROM/Firmware threads, for example the i9000 ROM or unofficial JH2 or JH3 ROM)
Your USB cable.
The firmware files.
Steps:
Remove battery, SIM card and micro SD card.
Open Odin on the computer.
Put the battery back in.
Plug in the USB cable to the phone.
Hold both volume up and down.
With VOL up/down held in, plug usb cable to the computer.
Your phone will show the beloved DOWNLOADING yellow image.
Odin:
Simply select the rom/firmware you want to flash to and enjoy.
I can confirm this will not overwrite the phone's internal 16gb storage, which is where most apps save backups to.
Future steps:
Before trying anything crazy, copy the entire phone internal 16gb storage to your computer. If you brick, you can always get a new captivate, copy the junk back and run a restore.
I recommend Titanium backup (donate the $6, the backup/restore is SUPER SUPER fast) along with Clockwork recovery. Clockwork's Nandroid makes full kernel backups and you can boot to recovery from the phone itself. No more adb reboot download or adb reboot recovery.
sorry for my english i have a 19000m the one from bell my phone boot with the GALAXY S LOGO WITH THE MUSIC BUT AFTER THAT BLACK SCREEN CAN I REPAIR THAT ?
Yes, odin is about your only hope here... Even if you boot into the bios and try to do a factory reset it will come up with error after error...
Reflashing will totally wipe and start fresh.
I am curious however. I think i isolated where my problem came from but I am still curious...
Did you try to sideload anything?
It happened to me twice with Bell's Vibrant version. The first time, just after one week after getting it (not rooted). They simply gave me a brand new one.
The second one took 3 week to go dead. Knowing my way around Linux Embedded systems, this time I investigated the issue. In recovery mode, there were error messages saying that the system could not fine the internal flash memory partitions. I could confirm from the kernel messages that partitions on internal sdcard had disappeared. I did factory reset, reflash original stock firmware with Odin, but it did nothing.
I Sent the phone back for repair and three weeks later, they gave me another one (probably refurbished!!).
My phone just turns on, with a black screen and the capacitive buttons lit up. Nothing else happens. When I try to go into download mode, it only goes back to this black screen. I does however detect that the phone is connected driver wise on the computer, but does not show up in Hemidall or Odin. I've tried just about everything
i used ODIN to resotore the phont to stock
but when it finsh...i get black screen
and the phone dose not work or do anything.
any help plzzz
isa.ahmed said:
i used ODIN to resotore the phont to stock
but when it finsh...i get black screen
and the phone dose not work or do anything.
any help plzzz
Click to expand...
Click to collapse
Does it light up or display anything and then go black, or does it just do nothing? If it does nothing, you're probably bricked, but try this anyway just in case your phone still has some life in it:
open Odin; press and hold both volume buttons and plug in your USB. If Odin lights up yellow, flash.
If that doesn't work, buy or build a jig, use it, and see if it goes into download mode. If it doesn't, plug the cable in anyway and see if Odin recognizes it. If it does, flash.
If that doesn't work, you're probably bricked. JTAG or Unbrickable Mod are your options from here, neither of which I personally know anything about but you can search around and find someone who can help you.
Hard Bricked= No signs of life, black screen no matter what, no response to USB plug in. Nothing but Unbrickable mod or JTAG will fix, I WOULD SUGGEST getting Unbrickable because you only have to get it once, and it cost the same as JTAG.
Soft Bricked= DL mode access is available(by jig or button combo and usb), recovery too, has some life in it. Can use ODIN/HEIMDALL to fix it.
when the flashing finsh and say done...and show the green light in the ODIN. the phone did not start up
dose this mean it break or dead charger?
as m not shure if the battery is full or not.
anyway i can pass the battery by over it with cuted USB cable?
isa.ahmed said:
when the flashing finsh and say done...and show the green light in the ODIN. the phone did not start up
dose this mean it break or dead charger?
as m not shure if the battery is full or not.
anyway i can pass the battery by over it with cuted USB cable?
Click to expand...
Click to collapse
If you got a green light, I would think it should at least turn on. However, if it was a successful flash, it should charge with the phone off. A bricked phone and a bad charger would both look the same: dead.
Try a different charger or battery if you think your battery could that dead. However if your battery died during your flash, that could also be the cause of your brick.
i charge the battery...and nothing happend
will the USB JAG solve it?
as i read in some post this will not
i need to send to some one to do it by opeing the phont it self
isa.ahmed said:
i charge the battery...and nothing happend
will the USB JAG solve it?
as i read in some post this will not
i need to send to some one to do it by opeing the phont it self
Click to expand...
Click to collapse
A jig is worth trying, but I suspect it will not solve your issue. You are correct, you need to send it to someone to have it fixed. Send a PM to AdamOutler or Connexion2005 and they can point you in the right direction.
what a crapy phone
i had Moto Defy and i never face same issue
so now am end with usellss phone..and need to theough away
what a waist of mony
isa.ahmed said:
what a crapy phone
i had Moto Defy and i never face same issue
so now am end with usellss phone..and need to theough away
what a waist of mony
Click to expand...
Click to collapse
You moto defy never flashed boot loaders since Motorola always had them locked down, and if you didn't know what you were doing flashing the stock Emma's that had boot loaders then it is not the phones fault. You should never really have to flash boot loaders and that is the ONLY risky part in flashing on these phones. Other than that Samsung cappys are almost TRUELY unbrickable (HARD BRICK) unless you mess up flashing boot loaders. WHICH YOU DID WHETHER YOU KNEW IT OR NOT BY FLASHING THE STOCK ODIN. SEND IT FOR UNBRICKABLE MOD, it is cheap repair and you WONT run into your same mistake ever again.
Sent from My KickAss CM7 Captivate
so no way i can do it here?
need to send it?to who i send? and who to trust?
i found some one will do for 50$
http://www.mobiletechvideos.com/blog/?page_id=776
Adam Outler
Sent from my SGH-I897 using xda premium
and other issue, i never toch the bootloader of it
i only re flash the OS of it only..and end with black screen.
this gay he will do what?
can the agent do it?
as it will be easer than to send it
can i have link of who will do it

[Q] Help me pls.. I think I've really bricked my P990

Hi all kind bros and sis,
Please help me out as I think I've really bricked my less than 2 months brand new Optimus 2X..
You see.. I rooted my P990 using unlock root and chanced upon CM7 and thought of giving it a try. I installed clockworkmod and downloaded the stable release of 7.1 for Optimus 2x.. following the instruction to do a Nandroid backup and proceeded with the Mod..
Not knowing that I need to wipe everything including data.. I just selected the Dalvik cache wipe and proceed with the mod. The process went for more than 15mins and I saw some graphics (the android figure going round and round) but it just stuck there... the screen went blank and when I touched those home or back buttons.. they will lighted but nothing happens. I can't power it off also. So I manually took out the battery and put it back before powering up again. The android picture appeared again briefly for about 1 min and just hanged there. I took out the battery again and this time it was dead.. no matter what I press : vol + and power buttons together; home+Vol+ + power down; Vol- + power down.. all those do not revive the phone.
I tried taking out the external SD card and try powering up. The LG logo appeared and got stuck there.
I searched on Google and found the smartflashtool. I tried that and managed to install the NVidia boot recovery driver and stuff correct. Hold the vol+ button and power key before plugging in but the smarttool did not find the com port or communication driver whatever so I couldn't flash it back to stock.
I'm very desperate and stuck now... did I just accidentally burned the board or something? What bad luck I have
If that's the case, will I still be able to bring the phone back to LG service centre and get it repaired?
Please help me.. any kind souls out there. I really liked the phone and hoped to bring it back. else it's such a shortlived phone... really breaks my heart to see this..
Thanks in advance...
humblepie88 said:
Hi all kind bros and sis,
Please help me out as I think I've really bricked my less than 2 months brand new Optimus 2X..
You see.. I rooted my P990 using unlock root and chanced upon CM7 and thought of giving it a try. I installed clockworkmod and downloaded the stable release of 7.1 for Optimus 2x.. following the instruction to do a Nandroid backup and proceeded with the Mod..
Not knowing that I need to wipe everything including data.. I just selected the Dalvik cache wipe and proceed with the mod. The process went for more than 15mins and I saw some graphics (the android figure going round and round) but it just stuck there... the screen went blank and when I touched those home or back buttons.. they will lighted but nothing happens. I can't power it off also. So I manually took out the battery and put it back before powering up again. The android picture appeared again briefly for about 1 min and just hanged there. I took out the battery again and this time it was dead.. no matter what I press : vol + and power buttons together; home+Vol+ + power down; Vol- + power down.. all those do not revive the phone.
I tried taking out the external SD card and try powering up. The LG logo appeared and got stuck there.
I searched on Google and found the smartflashtool. I tried that and managed to install the NVidia boot recovery driver and stuff correct. Hold the vol+ button and power key before plugging in but the smarttool did not find the com port or communication driver whatever so I couldn't flash it back to stock.
I'm very desperate and stuck now... did I just accidentally burned the board or something? What bad luck I have
If that's the case, will I still be able to bring the phone back to LG service centre and get it repaired?
Please help me.. any kind souls out there. I really liked the phone and hoped to bring it back. else it's such a shortlived phone... really breaks my heart to see this..
Thanks in advance...
Click to expand...
Click to collapse
Try using SmartFlashTool, download the LG stock ROM (can be found here in XDA forum, i'll help you find the link), flash the .bin and .fls files.
humblepie88 said:
Please help me out as I think I've really bricked my less than 2 months brand new Optimus 2X..
...
"Hold the vol+ button and power key before plugging in but the smarttool did not find the com port..."
Click to expand...
Click to collapse
Turn off the phone. Hold Vol-DOWN while plugging it in. Start Smartflash and see the com-ports magically appear.
Follow trymhansen's instructions. He helped me before with my softbricked phone.
I hope you get your O2X back to life! Keep us posted
Best of luck to you!
PS. I also believe you should pull out the battery after turning off the phone in Trym's instructions. Trym correct me if I'm wrong please.
Hi All,
Thanks for your kind replies. I did follow your instruction. Take out the battery (I removed the ext SDcard as well), press and hold -vol and plug in the phone via USB. Afterwhich start up smartflash tool.. still nothing happens and no com ports are found.. The version of smartflashtool that I used is Dec 2010. Do I need to get the latest one and also the LG united drivers installed?
I also tried starting smartflash tool before the sequence.. still the same. BTW.. my OS is Win 7. Is it supported?
Really at my end's wit. Hope I can bring my phone back to life soon and I'm not really bricking it. I heard Samsung phones are not that easy to brick and can get to the recovery mode pretty easily. is it true?
Please help me.. thanks
Hi bros,
Attached are my screenshots from the device manager and smartflash tool... both seems not able to find the phone and allocate a com port. I've tried installing the latest LG mobile driver 3.6 but no help as well
Have you followed instructions as described here http://forum.xda-developers.com/showthread.php?t=1008070 ?
Also, try to attach your phone directly to computer, using usb ports from computer mainboard. I have experienced problems when attaching it via extension usb cord or attaching it to computer case ports. (I hope that you can understand what I have mean to say with usb )
Hi Memhis,
Yes.. I followed exactly the instructions from the thread and I've plugged into a USB port directly to the computer which is one of the ports in front.. not via any extension or USB hub.. still it did not detect.
I'll try to use another computer which is running Win XP and try again. I've downloaded those 3 files from that thread you recommended try using those instead.. hope it can be detected this time else I think I'll have to send to LG service for repair tomorrow.
I've been jailbreaking and modding my Iphone a lot and everytime whenever there's a near brick situation.. I'm able to fix it but not this time with an Android or LG perhaps... I hope I don't have to go to the extend of using ADB low level to push some files which I saw in one of the thread that one of the guys did that.. but I doubt I can since my windows can't even detect the phone!!
Maybe this will be my first and last LG phone if I ever get it repaired...
humblepie88 said:
Hi Memhis,
Yes.. I followed exactly the instructions from the thread and I've plugged into a USB port directly to the computer which is one of the ports in front.. not via any extension or USB hub.. still it did not detect.
I'll try to use another computer which is running Win XP and try again. I've downloaded those 3 files from that thread you recommended try using those instead.. hope it can be detected this time else I think I'll have to send to LG service for repair tomorrow.
I've been jailbreaking and modding my Iphone a lot and everytime whenever there's a near brick situation.. I'm able to fix it but not this time with an Android or LG perhaps... I hope I don't have to go to the extend of using ADB low level to push some files which I saw in one of the thread that one of the guys did that.. but I doubt I can since my windows can't even detect the phone!!
Maybe this will be my first and last LG phone if I ever get it repaired...
Click to expand...
Click to collapse
launch smartflashtool first, extract the .fls and .bin files, hold down volume at the same time plug in the usb port to your comp. you must see a s/w updating logo in your phone's screen and smartflash should detect your phone. then click start!
Sent using a phone.
Hi mrgian,
I just tried to revive my phone by using the same method on a different laptop running on Win XP.. plugged directly to a side USB port but still no luck. There's no s/w updating logo appearing on my phone and smartflashtool also failed to detect my phone. I've found another thread opened by another user and my situation is exactly the same as his :
http://forum.xda-developers.com/showthread.php?t=1161583
But lucky for him is that he's able to get it working after changing to another PC but I've tried 3 different machines and no luck so far...
I'll try to use the NVflash as a last resort and see if I've any luck with NVflash at all.. If it failed again.. I think I've no choice but to send it to the repair centre for servicing then..
humblepie88 said:
Hi mrgian,
I just tried to revive my phone by using the same method on a different laptop running on Win XP.. plugged directly to a side USB port but still no luck. There's no s/w updating logo appearing on my phone and smartflashtool also failed to detect my phone. I've found another thread opened by another user and my situation is exactly the same as his :
http://forum.xda-developers.com/showthread.php?t=1161583
But lucky for him is that he's able to get it working after changing to another PC but I've tried 3 different machines and no luck so far...
I'll try to use the NVflash as a last resort and see if I've any luck with NVflash at all.. If it failed again.. I think I've no choice but to send it to the repair centre for servicing then..
Click to expand...
Click to collapse
does the laptop have lg drivers installed?
Sent using a phone.
inflance hotota
mrgian said:
does the laptop have lg drivers installed?
Sent using a phone.
Click to expand...
Click to collapse
Yes.. I've installed the latest LG united mobile driver version 3.6. Any wrong with that version... Really don't know where / what is missing or my phone is really fried after just one mod attempt?
I've also tried NVflash and it's stuck at the "bootloader initialization" screen....
Nothing appeared on the phone... not even LG logo. Can't believe LG phones are so fragile and unmodifiable
humblepie88 said:
Yes.. I've installed the latest LG united mobile driver version 3.6. Any wrong with that version... Really don't know where / what is missing or my phone is really fried after just one mod attempt?
I've also tried NVflash and it's stuck at the "bootloader initialization" screen....
Nothing appeared on the phone... not even LG logo. Can't believe LG phones are so fragile and unmodifiable
Click to expand...
Click to collapse
can you entet CWM? Press volume down til s/w will appear.
Sent using a phone.
try to charge the battery first...power off your device and charge it...maybe leave it charging for about 1hr even if you dont see anything on the screen( i believe after plugin the charger you will see the charging logo but it will disapear after a few seconds)...after 1 hr unplug and try to check if it will boot to clockwork recovery...if yes then just do complete data wipe...also try installing the ext3 back.zip, it will help delete system files(sometimes CWR is not deleting this)...hope this help
chupi_24 said:
try to charge the battery first...power off your device and charge it...maybe leave it charging for about 1hr even if you dont see anything on the screen( i believe after plugin the charger you will see the charging logo but it will disapear after a few seconds)...after 1 hr unplug and try to check if it will boot to clockwork recovery...if yes then just do complete data wipe...also try installing the ext3 back.zip, it will help delete system files(sometimes CWR is not deleting this)...hope this help
Click to expand...
Click to collapse
you got a point there.
Sent using a phone.
humblepie88 said:
Yes.. I followed exactly the instructions from the thread and I've plugged into a USB port directly to the computer which is one of the ports in front.. not via any extension or USB hub.. still it did not detect.
Click to expand...
Click to collapse
When you say an USB port in the front do you mean an USB in the back? Because the ones in front are the case ones, the ones in the back are the good ones, i.e. the ones that are directly attached to the mobo.
LarsPT said:
When you say an USB port in the front do you mean an USB in the back? Because the ones in front are the case ones, the ones in the back are the good ones, i.e. the ones that are directly attached to the mobo.
Click to expand...
Click to collapse
I've tried the recovery via 2 diff laptops and plugging in directly to one of the side USB ports but to no avail as well.. I think I've plugged in the phone correctly but there's no reaction at all/
mrgian said:
can you entet CWM? Press volume down til s/w will appear.
Sent using a phone.
Click to expand...
Click to collapse
How to enter CWM? I can't even power up the phone and no reaction at all when plugged into USB via smartflash.. the screen remains black. It's liked the whole phone is burned or something... but strange thing is that it can detect APX and asked to install drivers... but after successfully installing the Nvidia boot recovery driver.. the com ports does not get discovered.. What is wrong?
chupi_24 said:
try to charge the battery first...power off your device and charge it...maybe leave it charging for about 1hr even if you dont see anything on the screen( i believe after plugin the charger you will see the charging logo but it will disapear after a few seconds)...after 1 hr unplug and try to check if it will boot to clockwork recovery...if yes then just do complete data wipe...also try installing the ext3 back.zip, it will help delete system files(sometimes CWR is not deleting this)...hope this help
Click to expand...
Click to collapse
I plugged in the phone with battery but there was no charge logo or whatever.. the screen remains blank.. I'll try to leave it charging and see what happens. But I've remembered there was still about 80% power when this disaster happened and I've taken out the battery since.. so the charge should have remain? Btw.. where can I get this ext3 back.zip and how to use it? thanks

Really (I mean *really*!) bricked my phone. Nothing works.

Hi p970ies,
EDIT: NEW problems, see last pages.
here is my story:
I was on IZS v1.1, when I decided to go into recovery and make a full-wipe for having a "fresh install" again. You know, the phone was laggy, I had to many apps etc. I pressed the on/off-button for 1-2 secs to reboot into recovery, then my phone turned off and restarted but just with a "bright" black screen, the display was on. I thought "something went wrong", pulled the battery out and put it back in again, started, but then same screen again.
A few months ago an easy "unbricking" method (I know, not really unbricking) was to flash Redy2006's touch-recovery and boot into it with his scripts. So I flashed it (I know it's dumb, because of the u-boot and v30 thing, Idk), same result.
After that, I grabbed smartflash and two .bin/.fls packs of 2 roms, went into that special mode (phone off, press vol+, plug in) but there was no "sign" (screen that shows that you are in that mode) like the other day, the screen kept being black, but on.
Nonetheless the flashing worked and the software said everything alright. I started the phone but same result, in addition that there was now this effect: When the battery is put in and/or the phone is charging, the screen changes from being on and off. I can't do anything, no restarting with buttons, no LG screen, nothing but on and off, on and off. Every few seconds.
Thank you, I hope you experts can help me. (Even when I have the phone 2 years now and I was a ROM-junkie since the first day )
Edit: Tried smartflash with another patched v20 ROM. Tried KDZ Updater, just errors. But now the phone seems to boot, but there's nothing on the display, just the 4 softkeys are fading in and out.
Tomatengelee said:
Hi p970ies,
here is my story:
I was on IZS v1.1, when I decided to go into recovery and make a full-wipe for having a "fresh install" again. You know, the phone was laggy, I had to many apps etc. I pressed the on/off-button for 1-2 secs to reboot into recovery, then my phone turned off and restarted but just with a "bright" black screen, the display was on. I thought "something went wrong", pulled the battery out and put it back in again, started, but then same screen again.
A few months ago an easy "unbricking" method (I know, not really unbricking) was to flash Redy2006's touch-recovery and boot into it with his scripts. So I flashed it (I know it's dumb, because of the u-boot and v30 thing, Idk), same result.
After that, I grabbed smartflash and two .bin/.fls packs of 2 roms, went into that special mode (phone off, press vol+, plug in) but there was no "sign" (screen that shows that you are in that mode) like the other day, the screen kept being black, but on.
Nonetheless the flashing worked and the software said everything alright. I started the phone but same result, in addition that there was now this effect: When the battery is put in and/or the phone is charging, the screen changes from being on and off. I can't do anything, no restarting with buttons, no LG screen, nothing but on and off, on and off. Every few seconds.
Thank you, I hope you experts can help me. (Even when I have the phone 2 years now and I was a ROM-junkie since the first day )
Edit: Tried smartflash with another patched v20 ROM. Tried KDZ Updater, just errors. But now the phone seems to boot, but there's nothing on the display, just the 4 softkeys are fading in and out.
Click to expand...
Click to collapse
Oh man, its sad to hear that.
I can just think on two situations.
One is a broken screen, but thats pretty obvious.
And the other is a broken boot partition. Its very strange that you cant get into software upgrade mode. You sure you removed SIM, battery and SD, and then plugged it to the cable while holding the volume buttons?
I dont doubt you did it well, just making sure. Anyways AFAIK you should be able to enter that mode unless you got a broken boot partition.
Best of luck, sorry Im not of much help.
Grakel said:
Oh man, its sad to hear that.
I can just think on two situations.
One is a broken screen, but thats pretty obvious.
And the other is a broken boot partition. Its very strange that you cant get into software upgrade mode. You sure you removed SIM, battery and SD, and then plugged it to the cable while holding the volume buttons?
I dont doubt you did it well, just making sure. Anyways AFAIK you should be able to enter that mode unless you got a broken boot partition.
Best of luck, sorry Im not of much help.
Click to expand...
Click to collapse
Hi, thank you for your answer.
Yesterday oder so, I connected my phone without SIM, SD and battery while pressing vol+ to my pc and it showed the S/W-Update "Wait while update is in progress" or something. I was happy because the display isn't broken. But then I flashed again and the display is as black as before...
I thought about a broken bootloader. Do you guys know a way to fix it? Or the boot partition?
Tomatengelee said:
Hi, thank you for your answer.
Yesterday oder so, I connected my phone without SIM, SD and battery while pressing vol+ to my pc and it showed the S/W-Update "Wait while update is in progress" or something. I was happy because the display isn't broken. But then I flashed again and the display is as black as before...
I thought about a broken bootloader. Do you guys know a way to fix it? Or the boot partition?
Click to expand...
Click to collapse
Im pretty sure that if you can see the software update mode, you can unbrick the device.
When you said you reflashed something, do you actually mean that you smartflashed the fls and bin files from a stock v20 rom? AFAIK the bin file carries a bootloader with it so it should get fixed if your problem is the bootloader.
And by the way, while the phone has that black screen and is stuck booting... Are you able to use adb commands? You could try to jump to the recovery with "adb reboot recovery" to see if you got a working recovery.
Best of luck, tell me how it goes
Grakel said:
Im pretty sure that if you can see the software update mode, you can unbrick the device.
When you said you reflashed something, do you actually mean that you smartflashed the fls and bin files from a stock v20 rom? AFAIK the bin file carries a bootloader with it so it should get fixed if your problem is the bootloader.
And by the way, while the phone has that black screen and is stuck booting... Are you able to use adb commands? You could try to jump to the recovery with "adb reboot recovery" to see if you got a working recovery.
Best of luck, tell me how it goes
Click to expand...
Click to collapse
yep, I tried every version (10, 20, 30) in bin/fls and kdz. But I never got the screen to show something again.
And no, I can't use adb commands, sadly. It says "cannot find device" or something like that.
Tomatengelee said:
yep, I tried every version (10, 20, 30) in bin/fls and kdz. But I never got the screen to show something again.
And no, I can't use adb commands, sadly. It says "cannot find device" or something like that.
Click to expand...
Click to collapse
Huhmmm... Quite strange.
You can try to open up device manager, look for the phone (will probably have no drivers and the icon will have a yellow triangle) and force installing adb drivers. After that you are supposed to use adb even in middle of a boot.
I'd say that your best chance is to get to your recovery, so you can wipe everything (even formatting system) and start from scratch...
Anyways Im no expert at all... Just trying to help.
Grakel said:
Huhmmm... Quite strange.
You can try to open up device manager, look for the phone (will probably have no drivers and the icon will have a yellow triangle) and force installing adb drivers. After that you are supposed to use adb even in middle of a boot.
I'd say that your best chance is to get to your recovery, so you can wipe everything (even formatting system) and start from scratch...
Anyways Im no expert at all... Just trying to help.
Click to expand...
Click to collapse
Sometimes ADB works, but it says "device offline". When I flashed PRE-IZS fls/bin from the spanish forum, and then V30B bin/fls, something really weird happens: The phone is on, the wake-button works well - it turns on and turns off the display and the softkeys. But the screen doesn't show anything - just black.
Hello there!
Did You try out the B2C tool provided by LG? And there is one other tool provided by LG. Just try these oit. If they dont work, then try claiming it under warranty. They might replace the motherboard.
P.S: If You have the money, sell this piece of **** and get a Sony or Samsung. Cheers!
Sent from my LG-P970 using xda app-developers app
rokr05 said:
Hello there!
Did You try out the B2C tool provided by LG? And there is one other tool provided by LG. Just try these oit. If they dont work, then try claiming it under warranty. They might replace the motherboard.
P.S: If You have the money, sell this piece of **** and get a Sony or Samsung. Cheers!
Sent from my LG-P970 using xda app-developers app
Click to expand...
Click to collapse
I think I'm going to buy a Nexus 4, but I have to convince my parents
Oh and yes, phone is older than 2 years and in Germany we only have 2 years of warranty I think.
Tomatengelee said:
Sometimes ADB works, but it says "device offline". When I flashed PRE-IZS fls/bin from the spanish forum, and then V30B bin/fls, something really weird happens: The phone is on, the wake-button works well - it turns on and turns off the display and the softkeys. But the screen doesn't show anything - just black.
Click to expand...
Click to collapse
An easy, possible fix for The Device offline is to use the latest ADB. Just use the attached zip anywhere and use ADB, its the latest version from the android SDK, but just the files required for ADB. My nexus 4 had the same problem, but Solved it by updating ADB.
ykumar00 said:
An easy, possible fix for The Device offline is to use the latest ADB. Just use the attached zip anywhere and use ADB, its the latest version from the android SDK, but just the files required for ADB. My nexus 4 had the same problem, but Solved it by updating ADB.
Click to expand...
Click to collapse
damn it says "error: device not found" when in S/W or bootloop... or device offline in bootloop
any ideas?
did you try patched bins ? (for being able to boot into recovery right after the flash process, maybe you just need right wipes)
#700th post yay...
Ilko said:
did you try patched bins ? (for being able to boot into recovery right after the flash process, maybe you just need right wipes)
#700th post yay...
Click to expand...
Click to collapse
Yes, I did, but Smartflash works "less" than the KDZ-Updater. Actually the phone beeped today while it was on (with some kdz flashed) :silly:
Is it possible to convert patched bin/fls files to kdz?
I don't know, probably not... what I can say is that kdzu doesn't perform full wipes since it's intended to update the system and keep datas at the same time. You probably need wipes...
Ilko said:
I don't know, probably not... what I can say is that kdzu doesn't perform full wipes since it's intended to update the system and keep datas at the same time. You probably need wipes...
Click to expand...
Click to collapse
Oh ok... But with KDZ-Updater, it's possible to turn the phone off and on (screens is "on" but shows the color black while the softkeys are on too).
I'll try again with Smartflash... Do you know another version of it or a good tutorial? Maybe I've done the wrong method or something...
there are several tuts in this forum. smartflash is the quickest and safest way to restore / unbrick as it erases everything in the internal memory
Ilko said:
there are several tuts in this forum. smartflash is the quickest and safest way to restore / unbrick as it erases everything in the internal memory
Click to expand...
Click to collapse
I know, but it never works. That problem is so weird! :silly:
Man, nothing works... After smartflashing display flashing off and on again, after kdz display on, softkeys flashing
ADB side service is not active while in S/W mode. The only chance to access to recovery is to boot normally, and access to the device via ADB. The problems are : device needs to pass initial boot process for being able to be detected by ADB (even if you don't see the desktop it's ok), and USB debug must be enabled by default...
so, if you can't pass initial boot process, no chance to use ADB, and, if it passes, usb debug must be enabled or device will remain offline...
Ilko said:
ADB side service is not active while in S/W mode. The only chance to access to recovery is to boot normally, and access to the device via ADB. The problems are : device needs to pass initial boot process for being able to be detected by ADB (even if you don't see the desktop it's ok), and USB debug must be enabled by default...
so, if you can't pass initial boot process, no chance to use ADB, and, if it passes, usb debug must be enabled or device will remain offline...
Click to expand...
Click to collapse
Is there a chance to enable it manually?
the only chance is to flash a ROM which have it enabled by default for the most of them.
mine died because of the new twrp 2.6. It has definitively corrupted the boot partition as even smartflash can't ends its process. I had to buy another device...

[Q] Free Xperia 10.2 Battery drained out bootloop

Custom ROM: FXP312
I have zero percent battery.
when i plug in the charger, red led shows up for 5 minutes.
afterwards, the phone boots up comes to home screen and shuts down because of low battery(0%).
this keeps on repeating.
how to fix this?
cant connect to flash tool.
black_dagger said:
Custom ROM: FXP312
I have zero percent battery.
when i plug in the charger, red led shows up for 5 minutes.
afterwards, the phone boots up comes to home screen and shuts down because of low battery(0%).
this keeps on repeating.
how to fix this?
cant connect to flash tool.
Click to expand...
Click to collapse
This happens with me to, and I asked this here and the people have helped me.. Search just a few pages before this thread and you will see my thread. Sorry for my english.
sejis99 said:
This happens with me to, and I asked this here and the people have helped me.. Search just a few pages before this thread and you will see my thread. Sorry for my english.
Click to expand...
Click to collapse
so which method worked for you?
thanks
Yes that lack of off line charging for some custom ROMS almost made me send my phone in to repair. This was made worse by the fact that the build of CM I was on didn't allow you to boot into recovery (you could only reboot into recovery)
What I did.
Take the back cover of and have a pen ready so that you can use the hard power off function.
Prep your computer with flashtool open, drivers installed etc. – so that you can flash doom kernel as quickly as possible (you may only have 20 or so seconds).
1. Charge your dead phone, but AS SOON as begins to power up use your pen to power it down until it vibrates three times,
2. At this point you’ll hopefully have enough charge to enter fastboot mode, if not repeat stage 1. you may have to repeat stage 1. three or four times. If yes, flash doom kernel – do it quickly.
3. Go back to stage 1. But instead of powering off, see if you can boot in to CWM recovery, because the SP can be charged in CWM – if you can get into CWM all is good.
thanks both of you !
now im able to get into cwm but theres no led light indicating its charging.
hope its charging.
ill update you in 20 minutes
If you can get into CWM see if you can flash the offline charging fix appropriate to the ROM you're using (just to be sure).
so i got my battery up again!
but i have another question now.
after i installed doomlord kernel i had to reinstall fxp323.
else it was bootlooping.
now the doomlord kernel is gone.
how do i keep both?
Doom lords kernel is only for stock ROMs, I don't think cm kernels allow you to charge in cwm which is why I recommended it. Just flash the offline charging fix and you'll never have this problem again.
Sent from my C5303 using XDA Premium 4 mobile app

Android expert needed to repair bricked phone

ANDROID EXPERT NEEDED TO REPAIR BRICKED PHONE
Anyone in my area know how to fix a soft bricked Android phone? I have a Sony Xperia Z3 compact that is not responsive and I've tried everything and scoured the internet, mostly XDA, on how to get it back. I was trying to flash the Sony Concept Marshmallow ROM with the Boot and OTA, per the instructions in the thread. I wiped my device, flashed ROM, Boot, and OTA. Then I rebooted my device and then nothing, but a black screen and no response from the phone. It does not boot up or turn on. The screen does not flicker or anything. I can hold volume down and power and it will vibrate, but still nothing on the device. I can hold volume up and plug in the device and it will show me the blue led that it is connected to fast boot, but I cannot seem to do anything with it at that point. My computer does recognize it, but I can't figure out what to do from there with Flashtool or any other software.
If you are available where we can meet up that would be fantastic. I'm in the Chicago suburbs.
alwaysbelieve1 said:
ANDROID EXPERT NEEDED TO REPAIR BRICKED PHONE
Anyone in my area know how to fix a soft bricked Android phone? I have a Sony Xperia Z3 compact that is not responsive and I've tried everything and scoured the internet, mostly XDA, on how to get it back. I was trying to flash the Sony Concept Marshmallow ROM with the Boot and OTA, per the instructions in the thread. I wiped my device, flashed ROM, Boot, and OTA. Then I rebooted my device and then nothing, but a black screen and no response from the phone. It does not boot up or turn on. The screen does not flicker or anything. I can hold volume down and power and it will vibrate, but still nothing on the device. I can hold volume up and plug in the device and it will show me the blue led that it is connected to fast boot, but I cannot seem to do anything with it at that point. My computer does recognize it, but I can't figure out what to do from there with Flashtool or any other software.
If you are available where we can meet up that would be fantastic. I'm in the Chicago suburbs.
Click to expand...
Click to collapse
I think you phone isn't really bricked Try this, maybe it will help:
1. Download newest flashtool
2. Download proper .ftf file from the general section
3. Launch flashtool, plug your phone while holding vol down and wait until the drivers install. Unplug the phone after the drivers install.
4. Click a small thunder-shaped button in flashtool
5. Navigate to a folder with your .ftf file
6. You will see a menu where you can select what to flash and what not to flash. You might want to have everything from the top right window selected (data, cache, apps log will be wiped) and everything from the window below NOT selected (everything will be flashed). Click flash and wait for the files to be prepared.
7. You will see a window with the instructions how the phone should be plugged to a computer. Again, plug the phone while holding vol down, the LED will flash green.
8. Wait for the files to be flashed. If you get any error, try the flashing again after restarting flashtool. If you still get errors, reboot the computer and try again.
I hope this will work and instructions are not messed up but clear to you, I wrote them quickly.
romcio47 said:
I think you phone isn't really bricked Try this, maybe it will help:
1. Download newest flashtool
2. Download proper .ftf file from the general section
3. Launch flashtool, plug your phone while holding vol down and wait until the drivers install. Unplug the phone after the drivers install.
4. Click a small thunder-shaped button in flashtool
5. Navigate to a folder with your .ftf file
6. You will see a menu where you can select what to flash and what not to flash. You might want to have everything from the top right window selected (data, cache, apps log will be wiped) and everything from the window below NOT selected (everything will be flashed). Click flash and wait for the files to be prepared.
7. You will see a window with the instructions how the phone should be plugged to a computer. Again, plug the phone while holding vol down, the LED will flash green.
8. Wait for the files to be flashed. If you get any error, try the flashing again after restarting flashtool. If you still get errors, reboot the computer and try again.
I hope this will work and instructions are not messed up but clear to you, I wrote them quickly.
Click to expand...
Click to collapse
Thank you and these instructions are clear. I have tried all this, but the issue is the Phone isn't recognized properly.
And my Flash tool isn't recognizing .ftf files.
Not sure if this will help ... but in your situation guess one is willing to try anything
Try using Flashtool 0.9.10.2beta6 - this version doesnt require USB Debugging to be turned on - which may be the reason the phone isnt recognized properly???
Looks like your boot.img have gone
Now download stock rom and flash only the boot.img,it may work
Good luck
I had something of a similar issue very recently where flashtool wouldn't do it after i had by stupid mistake wiped EVERYTHING.. I think i had lost boot.img. On startup i would get the very first Sony Xperia screen and then nothing else.
After kicking around a few threads for information i downloaded an older version of flashtool, 0.9.18.5, flashed a complete stock rom with that and all was well.
astmacca said:
I had something of a similar issue very recently where flashtool wouldn't do it after i had by stupid mistake wiped EVERYTHING.. I think i had lost boot.img. On startup i would get the very first Sony Xperia screen and then nothing else.
After kicking around a few threads for information i downloaded an older version of flashtool, 0.9.18.5, flashed a complete stock rom with that and all was well.
Click to expand...
Click to collapse
It won't even get to any screen... Just black screen of death.
It won't even get to any screen... Just black screen of death.
Click to expand...
Click to collapse
Hmmm.......curious and you have my sympathy.
Did you have any joy at all with an older version of flashtool? From what i have read around the place if you are getting ANY response from the phone at all in terms of the LED or vibration when power and vol up or down pressed then all is NOT lost. Seems it may be a matter of finding the right combinations of tools and ftf files .
When i was mucking around trying to resurrect mine i did have to install drivers (from the directory in flashtool) more than once as i tried different combinations. Was using my Win7 machine at work rather than my Win10 home PC.
good luck. Will be interested to see the outcome of this as any fix is good to know about.
astmacca said:
It won't even get to any screen... Just black screen of death.
Hmmm.......curious and you have my sympathy.
Did you have any joy at all with an older version of flashtool? From what i have read around the place if you are getting ANY response from the phone at all in terms of the LED or vibration when power and vol up or down pressed then all is NOT lost. Seems it may be a matter of finding the right combinations of tools and ftf files .
When i was mucking around trying to resurrect mine i did have to install drivers (from the directory in flashtool) more than once as i tried different combinations. Was using my Win7 machine at work rather than my Win10 home PC.
good luck. Will be interested to see the outcome of this as any fix is good to know about.
Click to expand...
Click to collapse
I got frustrated and moved onto the Nexus 5X and drawered the Z3C. If I ever get around to it I'll definitely post about it here.
Do you have windows 7?. Windows 10 have problems with flashtools and driver because secureboot.

Categories

Resources