Hard Bricked my Note 5 :) - Galaxy Note5 Q&A, Help & Troubleshooting

Hi all,
I was running Custom ROM on my Galaxy Note 5. (Minosauras ROM v10)
Suddenly today morning the display was garbled with coffee stain pixels and while tried powering on I also had vertical glitch.
No recovery , no download mode
I tried connected to ODIN. I could do it.
Downloaded Stock firmware and flashed it.
Alas ! No chance of life.
a) can anyone give me PIT file for Indian version 32GB.
I tried using N920G UUB and ZTO pit file.
Now I have problems flashing system.img which clearly means I have been using the wrong pit file.
Can anyone support me out of this hard brick ?

prabhu1980 said:
Hi all,
I was running Custom ROM on my Galaxy Note 5. (Minosauras ROM v10)
Suddenly today morning the display was garbled with coffee stain pixels and while tried powering on I also had vertical glitch.
No recovery , no download mode
I tried connected to ODIN. I could do it.
Downloaded Stock firmware and flashed it.
Alas ! No chance of life.
a) can anyone give me PIT file for Indian version 32GB.
I tried using N920G UUB and ZTO pit file.
Now I have problems flashing system.img which clearly means I have been using the wrong pit file.
Can anyone support me out of this hard brick ?
Click to expand...
Click to collapse
Don't worry about flashing stock just re flash your twrp recovery and then go from there.

MrMike2182 said:
Don't worry about flashing stock just re flash your twrp recovery and then go from there.
Click to expand...
Click to collapse
No recovery ; No download mode.
Can connect to ODIN on a blank screen. Very hard brick !
With TWRP --> Black Screen with recovery enabled. No touch or whatsoever due to blank screen.
Need the pit file for Indian N920G Marshmallow ROM.

prabhu1980 said:
No recovery ; No download mode.
Can connect to ODIN on a blank screen. Very hard brick !
With TWRP --> Black Screen with recovery enabled. No touch or whatsoever due to blank screen.
Need the pit file for Indian N920G Marshmallow ROM.
Click to expand...
Click to collapse
What does 'No recovery; no download mode' even mean? Pit file doesn't fix the bricked phone but correct the pit(csc) mapping. Do you exactly know how to get into download mode though? If your display has been damaged, it still can get into download mode by the correct button combination.

Konsstantine34 said:
What does 'No recovery; no download mode' even mean? Pit file doesn't fix the bricked phone but correct the pit(csc) mapping. Do you exactly know how to get into download mode though? If your display has been damaged, it still can get into download mode by the correct button combination.
Click to expand...
Click to collapse
Hi , The problem is the display is garbled and the LED was showing various colors.
I tried recovery button combination to force into recovery. It didnt work.
I tried download mode (No download symbol)
But got a attachment to ODIN (COM 1: Blue)
I assumed that the bootloader is corrupt and loaded entire firmware through ODIN.
Everything was OK. But no display yet.
I tried starting using power button (Nothing on display)
Now I try PIT file.... System.img failed flashing.
Tried loading TWRP recovery; adb found 2 devices a) Device b) Recovery
Tried using Heimdall.
Now ODIN fails after using pit file once which failed.
Mine gets detected in ODIN and that is all the life it has.

prabhu1980 said:
Hi , The problem is the display is garbled and the LED was showing various colors.
I tried recovery button combination to force into recovery. It didnt work.
I tried download mode (No download symbol)
But got a attachment to ODIN (COM 1: Blue)
I assumed that the bootloader is corrupt and loaded entire firmware through ODIN.
Everything was OK. But no display yet.
I tried starting using power button (Nothing on display)
Now I try PIT file.... System.img failed flashing.
Tried loading TWRP recovery; adb found 2 devices a) Device b) Recovery
Tried using Heimdall.
Now ODIN fails after using pit file once which failed.
Mine gets detected in ODIN and that is all the life it has.
Click to expand...
Click to collapse
If you used an incorrect PIT file when you really didn't need to then you probably corrupted your entire partition table..

MrMike2182 said:
If you used an incorrect PIT file when you really didn't need to then you probably corrupted your entire partition table..
Click to expand...
Click to collapse
Yeah I understood that.
Now I need the correct pit file for my ROM to repartition it.
Should I repartition through dd tool only ?
Anyhow since my patience went away, I threw it down a service center.
Service center called me up and said display is back, but couldnt restore my note.
Calls for mother board change ! So I got it thrown back to me !!
It seems now my display is back , can anyone help me in getting my note repartitioned ?
R Prabhakar

Related

[Q] My Galaxy Note(SHV-E160L) is bricked...

before writing, I'm so sorry for my pooooor English.
I live in Toronto, Canada. I bought my Galaxy Note(SHV-E160L) from Korea, so change sim card from LG U+ to Rogers.
but when I sleep, Note encounter Unlimited Reboot.
so I try to repair in 3-way.
first, Factory reset. but I could make Download mode only, couldn't make Recovery mode.
so I try Samsung Kies Recovery mode, but Kies show me binery Error.
last, I want to use ODIN, but ODIN show me Error Message, too.
"Complete(write) operation failed"
What this means?
If it can't be repaired, I must send my cell phone to Korea.
I'm very embrassed...
please help me!!
and Merry Christmas for you
Is it sticking on factoryfs.img in ODIN ? this usually means its bricked which kernel where you on when you did the factory reset ?
I had a similar issue last week, stuck in odin, everything failing, I was convinced it was bricked, I manage to repair it by (no joking here) flashing a million wrong things in ODIN.... But DO NOT TRY THIS lol
try to flash a safe kernel through ODIN, and then see if it bring back recovery, then you can wipe and flash a new rom (hopefully)
otherwise there is the pit file method to revive from a brick, which works well, but loses around 3gb of internal sd space
hello
hello bro...
try this method:
download a stock gingerbread rom then go into download recovery, flash it with odin, root your phone.
from here you can install any custom rom, this is how i do when i got bootloop.
Thanks for your reply
hanzo777 said:
hello bro...
try this method:
download a stock gingerbread rom then go into download recovery, flash it with odin, root your phone.
from here you can install any custom rom, this is how i do when i got bootloop.
Click to expand...
Click to collapse
Thanks, but when I use ODIN, ODIN got a trouble..
when It start to flash, ODIN shows error message (Complete(write) operation failed)..
so even I can't try another Kernel Files..
Sigea said:
Thanks, but when I use ODIN, ODIN got a trouble..
when It start to flash, ODIN shows error message (Complete(write) operation failed)..
so even I can't try another Kernel Files..
Click to expand...
Click to collapse
Perhaps should follow closely the guide for using odin from Dr ketan should help:
http://forum.xda-developers.com/showthread.php?t=1424997
1. Installation
- Download stock ROM (should start with a GB rom), and extract it to .tar file
- Download Odin, open it
- select PDA tab and point to ROM file. Leave Re-partition, pit, CSC, Phone tab unticked.
- Switch off device, Put in download mode (Vol down + Home + Power)
- completely close kies, Anti virus if running
- Connect device to PC
- ID com port shud turn yellow (not shown in image)
Now hit Start
----
see how it goes.
Same problem as OP
Hello guys,
unfortunately, I have the same problem with my 32GB SHV-E160L as OP. Little backstory:
I bought the GNote in Korea and brought it back to my country. I successfully rooted it with one of the guides here on XDA (Tegrak kernel, no OC whatsoever). No problems so far, the phone worked for weeks and I was able to do what you can do with rooted phones. One day while surfing the net it just crashed and was stuck in a boot loop. This is where I am now.
I tried:
Go into tegrak recovery. result: It gets stuck on samsung logo, funnily the phone would establish a usb connection if plugged in (as if in download mode)
Reset from Kies. result: After beeing told by Kies to go into download mode, instead of flashing the new software it gives an error message in Korean about missing binaries (see attachment)
Flash from odin. result: the dreaded red box with "fail" appears after the NAND write command
Now, after doing my research here on XDA I found out that my emmc might have damaged partitions and I need a PIT file. Here's where I'm stuck.... I can't find a PIT file for my 32GB note, only for the N7000 or the I717. And I don't want to mess things further up... so if anyone here could provide me with a PIT file, or tell me how to fix the phone through other means I would be really grateful
Thanks in advance....
You should ask hg42 if he can make one - in his thread I read that he did this before even for other devices.
So try a pm or post in his thread. Good luck

[Q] Ultimate brick

I rooted my sgs 3 mini and install custom ROMs. I loaded CM 11 (4.4.2 kitkat) from Maclaw.pl. It worked, but after few weeks, my fhone just suddenly shut down. Tried to unroot it via odin + stock ROM, but nothing happens. Or something happens, there is the samsungs own bootlogo back. But the phone is stuck on that logo. Funny part is that when I put a charger on, there appears maclaws panda charging logo. I tried to load stock charging logo via odin, but nothing happens. Phone won't get to recovery mode, but the download mode works. Any ideas what to do? Except to throw it to trash can...
If the download work so
Recovery also need to work
Try again
Also did you try flash by Odin
Sent from my GT-I8190 using xda app-developers app
oldmen said:
If the download work so
Recovery also need to work
Try again
Also did you try flash by Odin
Sent from my GT-I8190 using xda app-developers app
Click to expand...
Click to collapse
Won't go to recovery, have tried few weeks now. Download work, when tried to go recovery, it just showing the samsungs bootlogo
And yes tried flash stock ROM by odin plenty times.
Problems
Guys, i think i have similar problem. I rooted my sgs 3mini and put maclaw.pl kitkat 4.4.2, now after downloading some photos my mobile turned off, i tried to turn it on but it shown only: "samsung galaxy s3 mini i8190", after that restarted and now it wont even turn on...
Is there anything to save this mobile or? Iam soo angry on my self and on mobile -.-
blodrayn said:
Guys, i think i have similar problem. I rooted my sgs 3mini and put maclaw.pl kitkat 4.4.2, now after downloading some photos my mobile turned off, i tried to turn it on but it shown only: "samsung galaxy s3 mini i8190", after that restarted and now it wont even turn on...
Is there anything to save this mobile or? Iam soo angry on my self and on mobile -.-
Click to expand...
Click to collapse
Sad to hear :/ Hope someone can help us
Try this forum maybe will help you http://forum.xda-developers.com/showthread.php?t=2159660
Sent from my GT-I8190 using Tapatalk
oldmen said:
Try this forum maybe will help you http://forum.xda-developers.com/showthread.php?t=2159660
Sent from my GT-I8190 using Tapatalk
Click to expand...
Click to collapse
Thanks, but as I said, nothing happens. I have tried many times to flash stock firmware. I have read many posts and tips but it looks like that there is nothing to do :/
Staattius said:
Thanks, but as I said, nothing happens. I have tried many times to flash stock firmware. I have read many posts and tips but it looks like that there is nothing to do :/
Click to expand...
Click to collapse
It could be something with a corrupt param or something. Have you tried the service firmware also, not just the stock firmware?
Enable 3 button combo for recovery, do a factory reset and it will boot.
http://forum.xda-developers.com/showthread.php?t=2157105
deconectat said:
Enable 3 button combo for recovery, do a factory reset and it will boot.
http://forum.xda-developers.com/showthread.php?t=2157105
Click to expand...
Click to collapse
Tried, didn't work. Thanks for trying to help
You kan fix your phone like this
1. Download the pit file. If your phone is variant with 8Gb internal memory. Warning this pit file is only for 8Gb internal memory galaxy s3 mini all variant (i8190 i8190N i8190L) for the 16Gb variant googlelit for pit file
2. Put your phone on Download mode , conect usb cable to the phone and tick "re-partition" box
3. Choose on PIT tab your pit file from your pc where you downloaded
4. Choose on PDA tab the Stock room wat you want to flash.
5. Put again the phone in "Download mode" open again ODIN chose PDA and flash Stock Recovery. Be careful that the box is not checked "re-partition". Flash Normal. Warning this way increase binary count on Download mode. After reboot
6. Put your phone on recovery mode by holding the keys "HOME+VOLUME UP+POWER BUTONS and wipe factory reset,cashe partition and reboot the phone. Voala the phone is Works.
Follow the instructions as in the picture
joker79 said:
1. Download the pit file. If your phone is variant with 8Gb internal memory. Warning this pit file is only for 8Gb internal memory galaxy s3 mini all variant (i8190 i8190N i8190L) for the 16Gb variant googlelit for pit file
2. Put your phone on Download mode , conect usb cable to the phone and tick "re-partition" box
3. Choose on PIT tab your pit file from your pc where you downloaded
4. Choose on PDA tab the Stock room wat you want to flash.
5. Put again the phone in "Download mode" open again ODIN chose PDA and flash Stock Recovery. Be careful that the box is not checked "re-partition". Flash Normal. Warning this way increase binary count on Download mode. After reboot
6. Put your phone on recovery mode by holding the keys "HOME+VOLUME UP+POWER BUTONS and wipe factory reset,cashe partition and reboot the phone. Voala the phone is Works.
Follow the instructions as in the picture
Click to expand...
Click to collapse
Your pit-file have password protection?
Filpus said:
Your pit-file have password protection?
Click to expand...
Click to collapse
No
joker79 said:
No
Click to expand...
Click to collapse
Trying to unrar goldenxx.rar
and then comes this. its finnish and it says password needed
http://gyazo.com/9531e2ba608d103d39de9f51b32e9738
Try Now
Filpus said:
Trying to unrar goldenxx.rar
and then comes this. its finnish and it says password needed
http://gyazo.com/9531e2ba608d103d39de9f51b32e9738
Click to expand...
Click to collapse
Sorry i forgot the arhive have password. Try now i put a new arhive without password.
joker79 said:
Sorry i forgot the arhive have password. Try now i put a new arhive without password.
Click to expand...
Click to collapse
does not work :/ oh sorry forgot link http://gyazo.com/17371b77ef82a2f3804342284bdd3854
Filpus said:
does not work :/ oh sorry forgot link http://gyazo.com/17371b77ef82a2f3804342284bdd3854
Click to expand...
Click to collapse
You tick the box "re-partition" on odin ?
joker79 said:
You tick the box "re-partition" on odin ?
Click to expand...
Click to collapse
yep
Joker, have you found solution of this issue?
I have the same problem, also tried lot of thighs but nothing helped. Every try of using pit end-up with message "there is no pit partition", but stock FW I can falsh with no troubles.
Still the same behaviour only logo after staring phone and cannot get into recovery menu...

Help Galaxy s3 mini

Hello and i wish i can find solution for this
i bought GS3 MINI from friend and he flashed it now when the phone boot to the main screen to put the config the phone turns off immediately and boot again
when i tried to put it in odin mode i found at the bottom of the screen something HW REV 0x5 when i try to flash it with odin something appeares (movi create card session) with red line and there is no problem in odin i tried with alots of FW and it's the same problem
i tried to ERASE NAND ALL not working stuck at erase.... and unsuccessful.
PS : i can't go to recovery ..
custom binary download: yes (4 counts)
current binary:Samsung official
system status: custom
HW REV 0x5
Help help help !!!!!!!!!!!!!!!!!!!!!
6 Days with no help ?
Flash with PIT file and Re-partition box checked. PIT files are attached in the unroot/unbrick, flash stockrom, etc post
Chakapack said:
Flash with PIT file and Re-partition box checked. PIT files are attached in the unroot/unbrick, flash stockrom, etc post
Click to expand...
Click to collapse
i did everything without result
Can you take potos?
Resume:
1. You download the stock firmware?
2. Then, put your phone in Download mode (volumen down + menú + power)?
3. Put .tar.md5 file on PDA slot?
4. Put PIT file in Pit slot option?
5. Then, f.reset, re-partition, and auto reboot are checked?
6. When you connect your phone in download mode, there is cheked in blue the ID:COM space?
7. When you press start everything go good and the proccess end?
8. What appears when the phone auto reboot after all the process?
I got the problem of partition encrypted corrupted (something like that) but pressing the reset button works for me. Try agaun everything and tell us whats happend
1. You download the stock firmware?
Yes
2. Then, put your phone in Download mode (volumen down + menú + power)?
Yes
3. Put .tar.md5 file on PDA slot?
Yes
4. Put PIT file in Pit slot option?
Yes
5. Then, f.reset, re-partition, and auto reboot are checked?
Yes
6. When you connect your phone in download mode, there is cheked in blue the ID:COM space?
Yes
7. When you press start everything go good and the proccess end?
Yes and with success and when check the phone its looks like nothing happened
8. What appears when the phone auto reboot after all the process?
normal and when he boots to configure the phone turns off immediately and reboots
Man that sounds like a hard brick. If after all this process the phone still with a bootloop I think, its dead.
Sorry but I cant help you :/
Chakapack said:
Man that sounds like a hard brick. If after all this process the phone still with a bootloop I think, its dead.
Sorry but I cant help you :/
Click to expand...
Click to collapse
Thanks alots , atleast you replied
No problem. We are here to help!
Enviado desde mi GT-I8190 mediante Tapatalk
darkerthan said:
Thanks alots , atleast you replied
Click to expand...
Click to collapse
Probably don't work but if you get a bootloop after all this process, try power off the phone (remove battery) and then try to access to Samsung recovery and do a wipe data.
I'll sell this phone and when I did a restore with Odin, I got a bootloop after this process but restarting the phone and getting access to Samsung recovery and doing a wipe date, it work.
Try it

note 3 powers on but the screen is black

Hallo,
black screen of my Samsung Galaxy Note 3 SM-N900.
I can enter recovery mode and download mode and the screen is work normally, and when charging, the screen display green battery charging, so the screen is not broken and well connected.
but when turning on my note 3, the screen remain black even I hear start up sounds and touch sound and see the LED lights.
I did booting, wipe data factory reset and wipe cache and flashing.. but still note work!!
what is the reason that the screen work in download and recovery mode.. and not work when I power on the device!
any suggestions?
thanks in advance
I guess you should download the latest firmware for your phone (from sites like sammobile.com) and use odin to flash that downloaded firmware on your phone. Guides for using odin are shown on youtube. Just make sure that the firmware is for your variant of the Note 3 or you might end up bricking your device.
You have the sm-900 or sm-900a? Big difference between the two phones.
audit13 said:
You have the sm-900 or sm-900a? Big difference between the two phones.
Click to expand...
Click to collapse
I have note 3 SM-N900
chetannaik24 said:
I guess you should download the latest firmware for your phone (from sites like sammobile.com) and use odin to flash that downloaded firmware on your phone. Guides for using odin are shown on youtube. Just make sure that the firmware is for your variant of the Note 3 or you might end up bricking your device.
Click to expand...
Click to collapse
I already flash my note 3 using odin, and also did full repaire firmware for 4 files(AP, BL, CP and CSC), still same problem
Flash the firmware as s single file with Odin 3.07. Are you performing a factory reset before booting the phone for the first time?
audit13 said:
Flash the firmware as s single file with Odin 3.07. Are you performing a factory reset before booting the phone for the first time?
Click to expand...
Click to collapse
i perform factory reset after flashing and remaining black screen.. then I did wipe data and factory reset still black screen.. I did flashing again, then full repair firmware for 4 files(AP, BL, CP and CSC), still same problem.
You always get a pass in Odin when you flashed the firmware a single file? You're flashing the latest ROM? If the answer is yes to both questions, it sounds like a hardware problem.
audit13 said:
You always get a pass in Odin when you flashed the firmware a single file? You're flashing the latest ROM? If the answer is yes to both questions, it sounds like a hardware problem.
Click to expand...
Click to collapse
yes for both question :crying: .. but why screen work in recovery mode and download mode if there is hardware issue!
Drivers are not being loaded in recovery or download mode.
loulou_skr said:
I already flash my note 3 using odin, and also did full repaire firmware for 4 files(AP, BL, CP and CSC), still same problem
Click to expand...
Click to collapse
Then it's most probably a hardware issue, though not a serious one, since you obviously can see the screen when in download or recovery mode.

galaxy s10 stuck on an error has occurred while updating device software

hi all...i got a second hand galaxy s10 g973f/ds that was stuck on the screen an error has occurred while updating the device software.use the emergency recovery function in the smart switch pc software..
here are where the issues are starting..by going to smart switch app the app doesnt recognize my device..it says unsupported device.so i cant follow any suggestions found on this forum like selecting the more option and then emergency recovery function cos the phone isnt recognized..theres only an option to recover using recovery code but unfortunately i dnt have that code.the other problem is that by using odin i dont know the exact firmware file that was installed previously on the phone so when i try to flash with odin a ramdomly downloaded firmware it fails if i use modded odin or it gets stuck on recovery.img if i use not modded odin..
i have to say that i cant get to download mode by the pressing of any combinations of keys..the only screen that appears is the above mentioned error..even that apoears only when connected to power supply or usb through pc..otherwise if cable is disconnected theres no way of getting it on..
now i would appreciate anyone who can suggest a solution for my problem or if anyone can tell me if theres a way to get to know the original factory installed firmware through the imei or serial number of the phone..
i thank in advance anyone who would spend his her time to help me..
joyjuayasinghe84 said:
hi all...i got a second hand galaxy s10 g973f/ds that was stuck on the screen an error has occurred while updating the device software.use the emergency recovery function in the smart switch pc software..
me..
Click to expand...
Click to collapse
Were you able to get it sorted out? Did you bring it to a Samsung Repair Center?
Look on the back of the phone and you will see the phone model number. Confirm that it is SM-G937F/DS so you will at least have the right firmware when you download it. It would probably be best to get the latest Android 10 firmware linked below. Download the latest Odin 3.14 if you weren't already using it.
You can download your firmware from here. I have the A70SM/DS and the original manual had Spanish on it and I was told it was the Latin America version. TCE is supposed to have the latest software patches at least for my A70. I do not know about the S10.
After your firmware is downloaded extract it to a folder. Copy the CSC to your desktop and delete the .md5 extension from the file. Use 7zip or PeaZip to open your CSC on your desktop and extract the PIT file. Save it in the original firmware (.tar.md5) folder. Delete the copied CSC from your desktop.
Open Odin with Admin privileges and connect the phone. Select all 5 of the downloaded files (BL, AP, CP, CSC and USERDATA). Select the Pit option and use the extracted pit from in your firmware folder. In the options menu select Auto Reboot, Nand Erase, Re-Partition, and F. Reset Time. ONLY USE NAND ERASE AND RE-PARTITION IF YOUR PHONE GETS PUT INTO EMERGENCY RECOVERY MODE. Start the flashing and wait for the phone to start up on its own. It might take up to 10 minutes on the first boot.
s10 stuck on an error has occurred while updating device software
hi cealaska.tnx for reaching out..m sorry that i didnt showed up on the forum for so long and couldnt reply to the message you hv sent...i still couldnt fix my s10...ill try your method in a while and keep you posted..really appreciate ur effort in trying to help me..
cealaska said:
Were you able to get it sorted out? Did you bring it to a Samsung Repair Center?
Look on the back of the phone and you will see the phone model number. Confirm that it is SM-G937F/DS so you will at least have the right firmware when you download it. It would probably be best to get the latest Android 10 firmware linked below. Download the latest Odin 3.14 if you weren't already using it.
You can download your firmware from here. I have the A70SM/DS and the original manual had Spanish on it and I was told it was the Latin America version. TCE is supposed to have the latest software patches at least for my A70. I do not know about the S10.
After your firmware is downloaded extract it to a folder. Copy the CSC to your desktop and delete the .md5 extension from the file. Use 7zip or PeaZip to open your CSC on your desktop and extract the PIT file. Save it in the original firmware (.tar.md5) folder. Delete the copied CSC from your desktop.
Open Odin with Admin privileges and connect the phone. Select all 5 of the downloaded files (BL, AP, CP, CSC and USERDATA). Select the Pit option and use the extracted pit from in your firmware folder. In the options menu select Auto Reboot, Nand Erase, Re-Partition, and F. Reset Time. ONLY USE NAND ERASE AND RE-PARTITION IF YOUR PHONE GETS PUT INTO EMERGENCY RECOVERY MODE. Start the flashing and wait for the phone to start up on its own. It might take up to 10 minutes on the first boot.
Click to expand...
Click to collapse
no luck bro..phone is still stuck as it was before.. the first time that i tried to follow ur guide i did everything as u said but in odin i got an error message saying re-partition operation failed..that message ive got only the first time i tried to follow your guide..all the following times i get an error saying fail! (device info)
im completely lost..ive tried different odin versions including patched one..ive tried different firmwares but nothing..still stuck at that message..
Hi! I have a s20 that is in exact same state. Have anybody any clue what to do?
I was stuck on this error and couldn't turn off the phone. Tried all the possible button combinations.
This method worked for me on the first try.
Thank you!
cealaska said:
Were you able to get it sorted out? Did you bring it to a Samsung Repair Center?
Look on the back of the phone and you will see the phone model number. Confirm that it is SM-G937F/DS so you will at least have the right firmware when you download it. It would probably be best to get the latest Android 10 firmware linked below. Download the latest Odin 3.14 if you weren't already using it.
You can download your firmware from here. I have the A70SM/DS and the original manual had Spanish on it and I was told it was the Latin America version. TCE is supposed to have the latest software patches at least for my A70. I do not know about the S10.
After your firmware is downloaded extract it to a folder. Copy the CSC to your desktop and delete the .md5 extension from the file. Use 7zip or PeaZip to open your CSC on your desktop and extract the PIT file. Save it in the original firmware (.tar.md5) folder. Delete the copied CSC from your desktop.
Open Odin with Admin privileges and connect the phone. Select all 5 of the downloaded files (BL, AP, CP, CSC and USERDATA). Select the Pit option and use the extracted pit from in your firmware folder. In the options menu select Auto Reboot, Nand Erase, Re-Partition, and F. Reset Time. ONLY USE NAND ERASE AND RE-PARTITION IF YOUR PHONE GETS PUT INTO EMERGENCY RECOVERY MODE. Start the flashing and wait for the phone to start up on its own. It might take up to 10 minutes on the first boot.
Click to expand...
Click to collapse
I was locked on Note 20 ultra, your instructions works fine, thanks a lot, I love you ;-)
cealaska said:
Were you able to get it sorted out? Did you bring it to a Samsung Repair Center?
Look on the back of the phone and you will see the phone model number. Confirm that it is SM-G937F/DS so you will at least have the right firmware when you download it. It would probably be best to get the latest Android 10 firmware linked below. Download the latest Odin 3.14 if you weren't already using it.
You can download your firmware from here. I have the A70SM/DS and the original manual had Spanish on it and I was told it was the Latin America version. TCE is supposed to have the latest software patches at least for my A70. I do not know about the S10.
After your firmware is downloaded extract it to a folder. Copy the CSC to your desktop and delete the .md5 extension from the file. Use 7zip or PeaZip to open your CSC on your desktop and extract the PIT file. Save it in the original firmware (.tar.md5) folder. Delete the copied CSC from your desktop.
Open Odin with Admin privileges and connect the phone. Select all 5 of the downloaded files (BL, AP, CP, CSC and USERDATA). Select the Pit option and use the extracted pit from in your firmware folder. In the options menu select Auto Reboot, Nand Erase, Re-Partition, and F. Reset Time. ONLY USE NAND ERASE AND RE-PARTITION IF YOUR PHONE GETS PUT INTO EMERGENCY RECOVERY MODE. Start the flashing and wait for the phone to start up on its own. It might take up to 10 minutes on the first boot.
Click to expand...
Click to collapse
seems like partly working for me!
I have Samsung SM-M315F/DSN and I was stuck on EMERGENCY RECOVERY MODE and after applying your solution I guess I'm on a boot loop... keeps rebooting and nothing else!
what else can I do please?
::EDIT::
after trying many things, I went into safe mode and did a Wipe Data/ Factory reset and it worked!
cealaska said:
Were you able to get it sorted out? Did you bring it to a Samsung Repair Center?
Look on the back of the phone and you will see the phone model number. Confirm that it is SM-G937F/DS so you will at least have the right firmware when you download it. It would probably be best to get the latest Android 10 firmware linked below. Download the latest Odin 3.14 if you weren't already using it.
You can download your firmware from here. I have the A70SM/DS and the original manual had Spanish on it and I was told it was the Latin America version. TCE is supposed to have the latest software patches at least for my A70. I do not know about the S10.
After your firmware is downloaded extract it to a folder. Copy the CSC to your desktop and delete the .md5 extension from the file. Use 7zip or PeaZip to open your CSC on your desktop and extract the PIT file. Save it in the original firmware (.tar.md5) folder. Delete the copied CSC from your desktop.
Open Odin with Admin privileges and connect the phone. Select all 5 of the downloaded files (BL, AP, CP, CSC and USERDATA). Select the Pit option and use the extracted pit from in your firmware folder. In the options menu select Auto Reboot, Nand Erase, Re-Partition, and F. Reset Time. ONLY USE NAND ERASE AND RE-PARTITION IF YOUR PHONE GETS PUT INTO EMERGENCY RECOVERY MODE. Start the flashing and wait for the phone to start up on its own. It might take up to 10 minutes on the first boot.
Click to expand...
Click to collapse
A year later you saved my phone ! Thanks a lot
Don´t know why it doesnt work by me but i am the brick king or so. If ya realy fckd up the flash at odin won´t go over Partion in the BL to get there out again i can just put it out and it goes by it self on again when nothing help i had to use Reiboot for Android would be nice if someone can figuere out how the programm put it back out of the Emergency Recovery Mode. tool is free in the test version so you have just to brick ya phone btw did it on a SM-G973F D/S hope you are smarter and didn´t even have to read this not just cause of ma english skills
happend on android 11 with twrp on magisk 23 cause forgot the decrypt thing img
cealaska said:
Were you able to get it sorted out? Did you bring it to a Samsung Repair Center?
Look on the back of the phone and you will see the phone model number. Confirm that it is SM-G937F/DS so you will at least have the right firmware when you download it. It would probably be best to get the latest Android 10 firmware linked below. Download the latest Odin 3.14 if you weren't already using it.
You can download your firmware from here. I have the A70SM/DS and the original manual had Spanish on it and I was told it was the Latin America version. TCE is supposed to have the latest software patches at least for my A70. I do not know about the S10.
After your firmware is downloaded extract it to a folder. Copy the CSC to your desktop and delete the .md5 extension from the file. Use 7zip or PeaZip to open your CSC on your desktop and extract the PIT file. Save it in the original firmware (.tar.md5) folder. Delete the copied CSC from your desktop.
Open Odin with Admin privileges and connect the phone. Select all 5 of the downloaded files (BL, AP, CP, CSC and USERDATA). Select the Pit option and use the extracted pit from in your firmware folder. In the options menu select Auto Reboot, Nand Erase, Re-Partition, and F. Reset Time. ONLY USE NAND ERASE AND RE-PARTITION IF YOUR PHONE GETS PUT INTO EMERGENCY RECOVERY MODE. Start the flashing and wait for the phone to start up on its own. It might take up to 10 minutes on the first boot.
Click to expand...
Click to collapse
Fixed my phone!
I've been trying for days to fix my bricked phone that was stuck in Emergency Recovery Mode after a bad flash. The major points I learned is to try several different usb ports and cables (original cable is better), get the correct and region specific firmware (The Samsung s10+ G975F/DS is the same as G975F), keep trouble shooting and retrying many, many times after Odin errors/failures, and to use this provided guide above.
Samsung Smart switch didn't help but this post did. This information saved my phone! I couldn't find this information anywhere else after hours of searching. Thank you very much!
Other people may find this tip helpful:
Q: My device is in bootloop, I can't acces download mode or recovery, no combo works, how do I get out ?
A: You can try following:
- Plug your phone in the PC with the USB cable. Then press/hold Bixby + Volume Down and hopefully it will boot to download-mode.
Otherwise try (still plugged in) force shutdown/restart by pressing/ holding Volume Down + Power - as soon as the screen turns off shift to pressing/ holding Bixby + Volume Down for download-mode. Try it at few times as its all about timing.
- If still no luck, unplug your phone and let the battery run out. Then press/hold Bixby + Volume Down and plug in to get to download-mode. This may take some time as the phone needs to recharge a little before it reacts.
- Once in download-mode flash your software before the update via Odin - I would use Home_CSC first trying to save your data.
I have a G970F which got stuck at 8% while flashing Ubuntu Touch system image to the SYSTEM partition with Heimdall on a Linux laptop. I think my laptop USB hardware isn't as good as it used to be. Anyway, am stuck on the error screen shown in the photo. Note that in the upper left corner of the screen is red text which is partially obscured by the curved screen corner, it says something then "Level [3921]". I have had no luck entering Download mode again with button combo + USB cable.
The device was stock Android 12 then has the Ubuntu Touch BOOT and VENDOR partitions flashed to it before it got stuck flashing the SYSTEM partition.
Is it possible to enter Download mode somehow again to begin the unbrick process?
zpunout said:
I have a G970F which got stuck at 8% while flashing Ubuntu Touch system image to the SYSTEM partition with Heimdall on a Linux laptop. I think my laptop USB hardware isn't as good as it used to be. Anyway, am stuck on the error screen shown in the photo. Note that in the upper left corner of the screen is red text which is partially obscured by the curved screen corner, it says something then "Level [3921]". I have had no luck entering Download mode again with button combo + USB cable.
The device was stock Android 12 then has the Ubuntu Touch BOOT and VENDOR partitions flashed to it before it got stuck flashing the SYSTEM partition.
Is it possible to enter Download mode somehow again to begin the unbrick process?
Click to expand...
Click to collapse
same here with my galaxy a50... cannot enter into download mode not in recovery. samsung smart switch pc software says it cannot connect to device...
zpunout said:
I have a G970F which got stuck at 8% while flashing Ubuntu Touch system image to the SYSTEM partition with Heimdall on a Linux laptop. I think my laptop USB hardware isn't as good as it used to be. Anyway, am stuck on the error screen shown in the photo. Note that in the upper left corner of the screen is red text which is partially obscured by the curved screen corner, it says something then "Level [3921]". I have had no luck entering Download mode again with button combo + USB cable.
The device was stock Android 12 then has the Ubuntu Touch BOOT and VENDOR partitions flashed to it before it got stuck flashing the SYSTEM partition.
Is it possible to enter Download mode somehow again to begin the unbrick process?
Click to expand...
Click to collapse
Similar situation here with an Exynos S10e (G970F), but it was already rooted with TWRP and a custom ROM, though I couldn't boot into recovery.
Unfortunately, the Linux situation seems bad at the moment. The only thing that worked for me was to try and plug the device into a Windows 7 VMware with Odin there. I could power off the screen for short moment with Vol+Power, and then VolDown+Power to get into a "fictionnal" download mode (because the screen didn't change) that would allow me to start flashing things with Odin.
With Odin in the VMware, I flashed the BL and the CL from the latest stock ROM from samfw.com, and the patched vbmeta.img (in CP slot) at the second reboot with the vbmeta warning. I then flashed a custom AP (with the boot.img of my custom ROM repacked and lz4-compressed, but without the gigangtic system.img; full content was "boot.img.lz4 dqmdbg.img.lz4 dtbo.img.lz4 dt.img.lz4 vbmeta.img.lz4 vendor.img.lz4"). From there, I could finally boot into TWRP and flash the .zip of my custom ROM.
I wonder if this would apply to my issue here: https://forum.xda-developers.com/t/samsung-s10-bootloop-erase-fail-read-only.4260661/
Please check out the uploaded photos of the above link in order to match the problem and find a solution
I remember that I got the phone working shortly afterwards back in January, but I cannot remember exactly how I did it. I think I might have used a Windows computer with Odin to return the device to the stock OS. I think download mode was working while the error screen was showing. I recommend reading about flashing stock firmwares on Samsung devices before attempting to do it so one doesn't accidentally wipe IMEI.
I also recommend taking photos of the phone screen when it is displaying serial numbers, firmware version numbers etc... before experimenting with it.

Categories

Resources