Hi hope someone can offer some advice, I have replaced the screen on my Z3 compact. Screen works fine but it is lifting and not sticking. I have tried different types of tape, I have applied tape to the edge of the screen itself and the frame it's still lifting. Please can someone offer some advice
Sent from my D5803 using Tapatalk
Any one got any advice, this must be an issue somewhere.
Sent from my D5803 using Tapatalk
ali.gore said:
Any one got any advice, this must be an issue somewhere.
Sent from my D5803 using Tapatalk
Click to expand...
Click to collapse
Consider buying a B-7000 glue, it is used for displays mostly, I was advised by a friend to use it, since my screen has unglued as well, and he has already repaired couple of Z3/Z3c devices with it, and there were no reported lifted screens since than. For the back panel, you can use double sided tape, but adding B-7000 glue on one side (to avoid cracking sounds, depending on the used tape probably). You can do a bit of searching on Youtube for repair videos, I recall watching some with the mentioned B-7000 glue, easy to find.
I haven't done it myself, but I will very soon, dust has filled my front cam, and proximity sensor.
Good luck.
Cirra92 said:
Consider buying a B-7000 glue, it is used for displays mostly, I was advised by a friend to use it, since my screen has unglued as well, and he has already repaired couple of Z3/Z3c devices with it, and there were no reported lifted screens since than. For the back panel, you can use double sided tape, but adding B-7000 glue on one side (to avoid cracking sounds, depending on the used tape probably). You can do a bit of searching on Youtube for repair videos, I recall watching some with the mentioned B-7000 glue, easy to find.
I haven't done it myself, but I will very soon, dust has filled my front cam, and proximity sensor.
Good luck.
Click to expand...
Click to collapse
other solution than b7000 ? from what i read on forums, after a while also this glue become "unglued"...clean, unclean, is still da same.
op3n said:
other solution than b7000 ? from what i read on forums, after a while also this glue become "unglued"...clean, unclean, is still da same.
Click to expand...
Click to collapse
I think B7000 will get the job done. I have used it for my device and it has been a month already, screen and back plate haven't moved a bit, its like new. One thing to remember though, you have to make sure the whole frame is COMPLETELY covered with glue, otherwise it will not be enough to hold the screen. I made a mess at first try, because I missed some spots and the screen lifted on sides, next time though, I've checked 3 times for any empty spots and applied glue to those spots, now everything is perfect. Of course, you should cover frame only, avoid applying that much so that glue is dripping inside the phone itself.
Good luck
Cirra92 said:
I think B7000 will get the job done. I have used it for my device and it has been a month already, screen and back plate haven't moved a bit, its like new. One thing to remember though, you have to make sure the whole frame is COMPLETELY covered with glue, otherwise it will not be enough to hold the screen. I made a mess at first try, because I missed some spots and the screen lifted on sides, next time though, I've checked 3 times for any empty spots and applied glue to those spots, now everything is perfect. Of course, you should cover frame only, avoid applying that much so that glue is dripping inside the phone itself.
Good luck
Click to expand...
Click to collapse
Gooood,ill give it a shot. But i was thinking if must remove back cover and the screen for glue only a corner...the back cover doesnt have any problem, only the display in left corner is unglued. And if i must to remove thats, i must buy and that adezive black or simple use only b7000 ? Thanks
I have some of the B-7000. Stuck the screen down over a week ago appears to be fine. The only issue I have is that I think the glue has squeezed onto the front camera, the camera is now blurred. I don't use the front one so it's not a big problem.
Sent from my D5503 using Tapatalk
op3n said:
Gooood,ill give it a shot. But i was thinking if must remove back cover and the screen for glue only a corner...the back cover doesnt have any problem, only the display in left corner is unglued. And if i must to remove thats, i must buy and that adezive black or simple use only b7000 ? Thanks
Click to expand...
Click to collapse
I have used the glue, it's fine, you don't need stickers
You can try applying the glue only in that corner as well, but I'm not sure how well will that fix the issue.
I had to remove the screen anyway to clean the notification led cutout and front camera, so I didn't care for the back plate sticker.
Cirra92 said:
I have used the glue, it's fine, you don't need stickers
You can try applying the glue only in that corner as well, but I'm not sure how well will that fix the issue.
I had to remove the screen anyway to clean the notification led cutout and front camera, so I didn't care for the back plate sticker.
Click to expand...
Click to collapse
go0o0d thanks man
Related
I have recently discovered a big stain on the top left corner of my 16GB screen. I'm not sure where it came from. I've used it for a few days when I decided to wipe it down with a microfiber cloth to no avail. The stain is on the outside of the glass. It feels rougher than the rest of the glass and especially noticeable when running over it with a stylus. I've also tried to wipe it down with a little bit of water, and noticed it beads differently than the rest of the glass.
Not sure what I can do to remedy this. I just might have to return it to Staples.
If you can simply return it then I wouldn't chance trying to fix it.
Strange problem.
That's what you get for drinking coffee and using your nexus 7.
But seriously though, just return it.
justinangil said:
I have recently discovered a big stain on the top left corner of my 16GB screen. I'm not sure where it came from. I've used it for a few days when I decided to wipe it down with a microfiber cloth to no avail. The stain is on the outside of the glass. It feels rougher than the rest of the glass and especially noticeable when running over it with a stylus. I've also tried to wipe it down with a little bit of water, and noticed it beads differently than the rest of the glass.
Not sure what I can do to remedy this. I just might have to return it to Staples.
Click to expand...
Click to collapse
The exact same thing happened to me after a day but in the middle, no idea how to fix it, also have screen lifting though so im getting a new one from Play story haha
does it look like it is just under the surface of the glass or on top of the glass, could be a problem with the glue etc which should be a returnable thing, you could have put something hot on the screen maybe and its done something with the glue?
davidcampbell said:
does it look like it is just under the surface of the glass or on top of the glass, could be a problem with the glue etc which should be a returnable thing, you could have put something hot on the screen maybe and its done something with the glue?
Click to expand...
Click to collapse
it's definitely on on top of the glass
the stain is not that noticeable unless you view it from an angle.
i only came across it when I ran my fingers across it and felt the rough area.
Its the oleophobic coating rubbing off. I had this happen with my galaxy nexus.
Sent from my Galaxy Nexus using xda premium
El Daddy said:
Its the oleophobic coating rubbing off. I had this happen with my galaxy nexus.
Sent from my Galaxy Nexus using xda premium
Click to expand...
Click to collapse
Thank for the technical explanation!
RMA!
Did you get any kind of solvent or solvent residue on the screen?
Same Staining Issue
Thought it was a smudge. At least Google was quick to remedy the problem.
I have the same problem on mine. Its almost a perfect circle on the lower right hand side of the screen when in portrait mode. That spot was a real grease magnet.
Just cleaned off the screen and put on a screen protector and now it is no longer a problem.
I have the exact same mark/stain on mine, upper right portion, I've decided to live with it. It is identical though.
Sent from my Nexus 7 using Tapatalk 2
Domino_13 said:
I have the same problem on mine. Its almost a perfect circle on the lower right hand side of the screen when in portrait mode. That spot was a real grease magnet.
Just cleaned off the screen and put on a screen protector and now it is no longer a problem.
Click to expand...
Click to collapse
So a screen protector solved the issue and made your spot unnoticeable? I called ASUS (didn't get mine from the Play Store) and sounds like they're willing to do an RMA. Not sure if I want to go through that hassle though, especially if a screen protector will solve the problem... not sure what I'll get back since I don't have the screen lift or any other issues with it
Bro the trick is when you're watching "Videos" that usually come in Adobe Flash only to aim away from the device....you know coughing and...other......stuff.... J/k rofl glad a screen protector fixed it for ya but there must have been a solvent on the screen or even if you touched something and had residue on your hands that could do it also.
Domino_13 said:
I have the same problem on mine. Its almost a perfect circle on the lower right hand side of the screen when in portrait mode. That spot was a real grease magnet.
Just cleaned off the screen and put on a screen protector and now it is no longer a problem.
Click to expand...
Click to collapse
Jevets said:
I have the exact same mark/stain on mine, upper right portion, I've decided to live with it. It is identical though.
Sent from my Nexus 7 using Tapatalk 2
Click to expand...
Click to collapse
pixelens said:
So a screen protector solved the issue and made your spot unnoticeable? I called ASUS (didn't get mine from the Play Store) and sounds like they're willing to do an RMA. Not sure if I want to go through that hassle though, especially if a screen protector will solve the problem... not sure what I'll get back since I don't have the screen lift or any other issues with it
Click to expand...
Click to collapse
I have the same problem with the perfect circle on the bottom right in portrait mode! Was thinking whether I should request exchange from newegg or Asus. However as per Pixelens comment, my N7 don't have other issues with flickering, screen lift etc. It bothers me only when I switch the screen off and at the correct light reflection.
Ok, so I have had the screen lift problem. It's on the left side worst in the middle. I decided I would take it apart and do the shims between the screws thing. But when I got it open the lift disappeared. So it's a problem with the back pressing up just enough... I noticed a pretty thick piece of foam right on the center left so I removed it. Just replaced the case and tada the tape is holding the screen flat just fine now. Just thought I would pass this on with the other fixes.
Danny80y said:
Ok, so I have had the screen lift problem. It's on the left side worst in the middle. I decided I would take it apart and do the shims between the screws thing. But when I got it open the lift disappeared. So it's a problem with the back pressing up just enough... I noticed a pretty thick piece of foam right on the center left so I removed it. Just replaced the case and tada the tape is holding the screen flat just fine now. Just thought I would pass this on with the other fixes.
Click to expand...
Click to collapse
I noticed last time I opened it that this foam had some compression marks. Likely from pressing against the back. Mine was slightly misaligned, so really only part was compressed. I had the same thought, i.e. remove it. Maybe align it, but it's glued on tight.
So I just removed it. I'll let you know how it turns out in a day or 2.
I also use 3 washers for the top 3 on the left, which helped huge. Hopefully this will make it perfect.
Update Sept 1. This definitely helps. Noticed from pics on another thread that some new models have this foam removed, as shipped. Interesting. Also, on new models, some have screws missing (2 and 4, starting top left). I tried removing screw 2 but when I woke up I noticed creaking and movement at the bezel, when I press my left thumb inwards, which is something I always do. So I put the screw (and washer) back in this morning. Perfect now. But removing this foam was essential, so thanks again.
Makes sense. The screen is dead flat, so it has to be the back case that is separating. Thanks for the info.
Sent from my Nexus 7 using Tapatalk 2
this isn't new and has already been covered already.
dilldoe said:
this isn't new and has already been covered already.
Click to expand...
Click to collapse
Can you point to where the foam issue was already covered? It was the first I saw.... maybe they have more pointers... Links?
Sent from my Nexus 7 using xda premium
mike5065 said:
Can you point to where the foam issue was already covered? It was the first I saw.... maybe they have more pointers... Links?
Sent from my Nexus 7 using xda premium
Click to expand...
Click to collapse
http://forum.xda-developers.com/showthread.php?t=1781237
http://forum.xda-developers.com/showpost.php?p=29028614&postcount=237
mike5065 said:
Can you point to where the foam issue was already covered?
Click to expand...
Click to collapse
It was covered in the main screen lift thread, which is like 90 pages long and has every possible remedy tested, dissected and mostly debunked. The fact is there are several factors causing the lift and there need to be several solutions to really fix it 100%, and permanently. You can make it better in various ways, one of which is removing that foam, although I believe the foam is there to keep the back from flexing and compressing those metal "prongs", causing them to lose contact. So you might have other problems later without the foam. I probably wouldn't mess with it, personally.
I personally think a workable solution for most N7's with this problem would be to shave that foam down evenly by like 0.3mm, then clamp the screen to the trim and leave it in a hot car like that for a day or so to re-adhere, without the back cover on. Then cool the tablet down and replace the back cover. The hard part is evenly shaving down the foam; it is just a tiny bit too big. But it should be present.
Well I thought I could live with it but the lift is back.... I have also noted that my 8gb gets really poor wifi connection compared to my wife's 16gb. All the clips are still contacting the back plate but I can see no difference in signal with or without the back on. So, I just called google and they are shipping out a new unit for me tomorrow. Hopefully this one is better.
Took the back off to look at screen lift fix. Low & behold 3 screws missing on the LH side of the unit. Also some fingerprints on the copper plates, 2 loose (more than 1 full turn to tighten) screws on the RH side, metal tape/gauze over phone socket loose.
badasscat said:
...So you might have other problems later without the foam...
Click to expand...
Click to collapse
Thanks for all this info. My foam was glued at about 25 degrees off-angle, and clearly compressed at the corner closest to the bezel, so a problem for mine' right from the factory. I didn't get it all off, but most for sure. Once removed, the bulge I had at that point between the bezel and rear case was gone. So was some screen lift' although the washers helped more for that. Not a big win, just another step forward.
I'm still curious why some pics on other thread show no foam, as shipped.
http://forum.xda-developers.com/showthread.php?p=30974024
From my looking, it's in a seemingly non-functional gap, and presses down a wide cable (or something). I earlier traced movement of that cable as the source of 'creaking' I was having, i.e. when it moved against another piece of plastic beside the bezel. I put some lithium where it rubbed and the creaking stopped. Mind you I did that (and the 3 washers precisely tightened) before i removed most of the foam.
My Tf101 was a lot less maintenance than this one. But once done (crossing fingers lol), it's causing my iPad3 to collect dust. This thing just screams. Loving it.
Again, thanks for the info.
Sent from my Nexus 7 using xda premium
I started noticing more and more dust gathering under the lens protection "window" but didn't think much of it since it didn't affect picture quality.
Then, after noticing a dark blotch on every shot I took, I saw the glass back pannel is loose in the upper half. The glue apparently came unglued (lol) and now I can easily put a matchstick between the glass pannel and the phone's body, the gap is that big. I tried pressing it back on, but the glue doesn't hold anymore.
Should I try to carefully pull the pannel off, clean out the dust (THERE IS A LOT OF IT UNDERNEATH) and put it back on with some double sided adhesive tape? Or should I take it to a phone service?
Thanks.
edit: How bad of an idea is taking it all off, cleaning the dust and super-glueing it back on myself?
zgomot said:
I started noticing more and more dust gathering under the lens protection "window" but didn't think much of it since it didn't affect picture quality.
Then, after noticing a dark blotch on every shot I took, I saw the glass back pannel is loose in the upper half. The glue apparently came unglued (lol) and now I can easily put a matchstick between the glass pannel and the phone's body, the gap is that big. I tried pressing it back on, but the glue doesn't hold anymore.
Should I try to carefully pull the pannel off, clean out the dust (THERE IS A LOT OF IT UNDERNEATH) and put it back on with some double sided adhesive tape? Or should I take it to a phone service?
Thanks.
edit: How bad of an idea is taking it all off, cleaning the dust and super-glueing it back on myself?
Click to expand...
Click to collapse
Hello!
First, turn off the device and remove the back cover entirely. Clean the lens with a cotton swab (be careful not to scratch it or leave lint on it ). Then put it back on and heat it with a hairdryer (on highest heat setting). Do it in circular motion around the edges for about a minute. After that(while still hot) grab it with a sheet and start applying small pressure on the sides(slide the sheet on them). Then let it cool and it should be ok. I have done this personally.
Hope this helps you!
P.S. If there is a lot of dust on the adhesive, wipe it gently with a wet rag and continue. The heat from the hair dryer should restore the glue.
BlAckXpeRia said:
Hello!
First, turn off the device and remove the back cover entirely. Clean the lens with a cotton swab (be careful not to scratch it or leave lint on it ). Then put it back on and heat it with a hairdryer (on highest heat setting). Do it in circular motion around the edges for about a minute. After that(while still hot) grab it with a sheet and start applying small pressure on the sides(slide the sheet on them). Then let it cool and it should be ok. I have done this personally.
Hope this helps you!
P.S. If there is a lot of dust on the adhesive, wipe it gently with a wet rag and continue. The heat from the hair dryer should restore the glue.
Click to expand...
Click to collapse
It does, I'll try this tonight. Thanks.
zgomot said:
It does, I'll try this tonight. Thanks.
Click to expand...
Click to collapse
If you have warranty then send it to service .
NexusGTS said:
If you have warranty then send it to service .
Click to expand...
Click to collapse
No warranty, so I did it myself. It worked perfectly, just that there is still that dark splotch and I made sure I cleaned the lens thoroughly. See the attached picture.
Can anything be done about that?
Sent from my C6903 using XDA Free mobile app
zgomot said:
No warranty, so I did it myself. It worked perfectly, just that there is still that dark splotch and I made sure I cleaned the lens thoroughly. See the attached picture.
Can anything be done about that?
Sent from my C6903 using XDA Free mobile app
Click to expand...
Click to collapse
I'm glad it worked!
About the dark spot: I searched on the internet and it appears to be dust problem. Clean the lens with a windows cleaning solution. If that doesn't work, you can open the phone(heat it with hairdryer using the same method and pull it out with a suction cup) and vaccum the camera module. Then turn it on(without cover) for testing. I hope that is the case. If this doesn't work there may be dust inside the camera module and that is tricky to fix.
You can read this to better understand the problem: LINK
I opened it again, VERY THOROUGHLY cleaned the lens with LCD cleaner fluid, but it didn't seem to do anything.
Anything else I can try?
Replace the camera
zgomot said:
I opened it again, VERY THOROUGHLY cleaned the lens with LCD cleaner fluid, but it didn't seem to do anything.
Anything else I can try?
Click to expand...
Click to collapse
I'm out of ideas. Repacing the camera is the only thing that comes in mind.
P.S. There might be a way to open the camera and clean it.
I am a Best Buy employee so should be no issue with getting an exchange. Looks like we have one of the 64GB AT&T ones in stock. Gonna be there bright and early to get mine exchanged.
I would advise everyone to keep an eye out.. I actually didn't notice it this morning. Around 6pm I noticed a black part on the screen and thought it was a glitch, so restarted but it was still there.
The line on the right side is just my temporary screen protector film. LOL. I bought an Invisishield and will install it on my replacement device tomorrow.
deepen915 said:
I am a Best Buy employee so should be no issue with getting an exchange. Looks like we have one of the 64GB AT&T ones in stock. Gonna be there bright and early to get mine exchanged.
I would advise everyone to keep an eye out.. I actually didn't notice it this morning. Around 6pm I noticed a black part on the screen and thought it was a glitch, so restarted but it was still there.
The line on the right side is just my temporary screen protector film. LOL. I bought an Invisishield and will install it on my replacement device tomorrow.
Click to expand...
Click to collapse
That's not a single deal pixel.
done12many2 said:
That's not a single deal pixel.
Click to expand...
Click to collapse
All good now.. got my replacement.
Also have installed a Invisible Shield.. After this picture was taken.
deepen915 said:
All good now.. got my replacement.
Also have installed a Invisible Shield.. After this picture was taken.
Click to expand...
Click to collapse
Did you go with the regular or HD InvisibleShield? I'm not a big fan of their new alcohol swab method for activating the adhesive on the HD model. I ended up using left over spray from several previous InvisibleShield installs.
When I used the alcohol swab provided, it just left lint embedded in he adhesive and I ended up with a bunch between the glass and the screen protector. I saw it before I even began to squeegee, so I broke out the spray and went old school. Turned out perfect after that.
InvisibleShield really screwed up this new application method because it leaves no room for error.
done12many2 said:
Did you go with the regular or HD InvisibleShield? I'm not a big fan of their new alcohol swab method for activating the adhesive on the HD model. I ended up using left over spray from several previous InvisibleShield installs.
When I used the alcohol swab provided, it just left lint embedded in he adhesive and I ended up with a bunch between the glass and the screen protector. I saw it before I even began to squeegee, so I broke out the spray and went old school. Turned out perfect after that.
InvisibleShield really screwed up this new application method because it leaves no room for error.
Click to expand...
Click to collapse
I did get the HD model. Yeah the swab was horrible. Mine had issues it has some lint on the bottom right corner. Screen is fully visible but slightly cloudy. Good thing I only paid $5 as an employee lol. I'll just buy another.
deepen915 said:
All good now.. got my replacement.
Also have installed a Invisible Shield.. After this picture was taken.
Click to expand...
Click to collapse
Actually, your InvisibleShield screen protector doesn't look anything like mine. Mine covers completely to through the curved edges. Is your protector for a different device?
deepen915 said:
I did get the HD model. Yeah the swab was horrible. Mine had issues it has some lint on the bottom right corner. Screen is fully visible but slightly cloudy. Good thing I only paid $5 as an employee lol. I'll just buy another.
Click to expand...
Click to collapse
Yeah, thanks for affirming that. I'm pretty sure they did the whole thing as a huge cost saving measure. It damn sure wasn't an improved method to install.
If you compare the savings between the difference in cost for the little plastic liquid spray canisters they provided and the supposed new and improved cheap alcohol swabs, Zagg just made out like a bandit.
Their packaging and marketing keeps getting better and better, but their quality and service keeps getting worse and worse.
done12many2 said:
Actually, your InvisibleShield screen protector doesn't look anything like mine. Mine covers completely to through the curved edges. Is your protector for a different device?
Click to expand...
Click to collapse
No this pic is yesterday morning and is not an invisible shield lol I said I installed after I took the pic. Installed it last night and looks just like yours. How did u do it so perfectly? I think I messed up by not using the squeegee in one motion. I did sections and I think it dried as I was doing it. I have some cloudiness and lint on the bottom. I'll have to get a new one.
deepen915 said:
No this pic is yesterday morning and is not an invisible shield lol I said I installed after I took the pic. Installed it last night and looks just like yours. How did u do it so perfectly? I think I messed up by not using the squeegee in one motion. I did sections and I think it dried as I was doing it. I have some cloudiness and lint on the bottom. I'll have to get a new one.
Click to expand...
Click to collapse
I knew as soon as I saw that piece of crap alcohol swap that the new method was flawed. ZAGG has lost their damn minds!!
The whole point behind getting these types of screen protectors on right is to get them and your fingers sprayed down really good. Once both are pretty much soaking, I pinch the protector between my finger and slide off excess fluid which in turn takes the lint/dust with it. Then I spray just a bit more on and apply it. I get it aligned and squeegee. While you are squeegeeing (is that a word?) and you come across a bubble that isn't going away, it isn't a bubble. It's lint/dust. Simply lift the protector at the edge and spray or apply some additional soapy water with your sprayer or fingers and get it out of there. Carefully fold the screen protector back so as to not allow additional lint/dust to get under there while you were dealing with the last one.
I don't try to use the squeegee to get every bubble. I just get most of the water out. Once 90% of it's gone, I work the edges with my fingers and around things like home buttons and camera lenses and sensors.
I guess my point is, even though their new instructions call for the use of the new alcohol swap, the old soapy water trick works perfectly fine. Actually, better.
done12many2 said:
I knew as soon as I saw that piece of crap alcohol swap that the new method was flawed. ZAGG has lost their damn minds!!
The whole point behind getting these types of screen protectors on right is to get them and your fingers sprayed down really good. Once both are pretty much soaking, I pinch the protector between my finger and slide off excess fluid which in turn takes the lint/dust with it. Then I spray just a bit more on and apply it. I get it aligned and squeegee. While you are squeegeeing (is that a word?) and you come across a bubble that isn't going away, it isn't a bubble. It's lint/dust. Simply lift the protector at the edge and spray or apply some additional soapy water with your sprayer or fingers and get it out of there. Carefully fold the screen protector back so as to not allow additional lint/dust to get under there while you were dealing with the last one.
I don't try to use the squeegee to get every bubble. I just get most of the water out. Once 90% of it's gone, I work the edges with my fingers and around things like home buttons and camera lenses and sensors.
I guess my point is, even though their new instructions call for the use of the new alcohol swap, the old soapy water trick works perfectly fine. Actually, better.
Click to expand...
Click to collapse
Alright so I'll buy another one tonight and see if that works. Good advice, thanks.
Here is what mine looks like.
deepen915 said:
Alright so I'll buy another one tonight and see if that works. Good advice, thanks.
Here is what mine looks like.
Click to expand...
Click to collapse
Looks pretty good to me. If your trying to get it closer to the edge, all I did was continue to work mine while it was still wet. Just a little at a time while I was working the water out from the center of the screen towards the edge.
Good luck man. Like I said, I think it looks great as it is now.
done12many2 said:
Looks pretty good to me. If your trying to get it closer to the edge, all I did was continue to work mine while it was still wet. Just a little at a time while I was working the water out from the center of the screen towards the edge.
Good luck man. Like I said, I think it looks great as it is now.
Click to expand...
Click to collapse
Got another one and did it again. Lint is gone now but got some micro bubbles. Let's see if it goes away. Not noticeable when screen is on.
Also even with no Zagg. I noticed some screen blemishes. Like it seems cloudy in some parts. I put brightness all the way while I was wiping it down to prepare the Zagg install. It's very noticeable. I may need to get my phone replaced again smh.
That completely sucks to hear about the cloudiness issue. I haven't heard of that one yet. I've heard of the swirls, scratches, and whites appearing yellow issues, but not the cloudiness.
I would lose my mind if I had to take a phone back twice for a screen related issue. It's probably not as big of a deal for you since you can do it while you're at work so to speak, but when your spending a grand on a phone, you just don't expect to have to take it back two times to be replaced.
Switching gears back to the bubbles in the Zagg. If you turn the screen on and they are barely noticeable, but with a slight prism light effect to them, you're fine. They'll dry up and be gone in hours.
If however you turn the screen on and see a shadow, it won't be going away when it's dried.
done12many2 said:
That completely sucks to hear about the cloudiness issue. I haven't heard of that one yet. I've heard of the swirls, scratches, and whites appearing yellow issues, but not the cloudiness.
I would lose my mind if I had to take a phone back twice for a screen related issue. It's probably not as big of a deal for you since you can do it while you're at work so to speak, but when your spending a grand on a phone, you just don't expect to have to take it back two times to be replaced.
Switching gears back to the bubbles in the Zagg. If you turn the screen on and they are barely noticeable, but with a slight prism light effect to them, you're fine. They'll dry up and be gone in hours.
If however you turn the screen on and see a shadow, it won't be going away when it's dried.
Click to expand...
Click to collapse
Yeah the Zagg is good enough for me.
And yeah I can see the cloudiness when scrolling on a white page in Chrome. I really don't want to have to exchange it again but may have to if it is really annoying me over the nextra few days.
It's like gray smudges going diagonally on the glass. I can't tell if its on the actual amoled panel or glass.
i have dead pixel on my Galaxy S6 Edge Plus
got the dead pixel after 4 Months using the phone.
how did i get a dead pixel??? i don't understand.
https://www.youtube.com/watch?v=_JbgaYIfdZo
seem's very small
do you think i should repair the phone?
I have had this phone for about 1.5 years now and it held up,it was running very well but it always had an overheating problem,you have probably seen me all over the forums asking how can I lower the temperature of the phone lol.
Well it has become less apparent with the latest build of Lineage,only when I am using Snapchat but that doesn't matter.
But now what started happening is my back glass is unsticking,the bottom part to be exact,I believe this is because the device heated up so much it weakened the adhesive.
So I am asking now with what material I can re-stick the back glass properly since I don't want it to hang like that for no reason.
Use fevibond
You can use fevibond(Synthetic Rubber Base Glue). I used it to stick front screen peeling off from top left corner.
Dhgr8 said:
You can use fevibond(Synthetic Rubber Base Glue). I used it to stick front screen peeling off from top left corner.
Click to expand...
Click to collapse
Could I use something like superglue or something similar to that?
Dinkec27 said:
Could I use something like superglue or something similar to that?
Click to expand...
Click to collapse
No, that would make it tough/impossible to separate it for repairs.
Please refer to this thread https://forum.xda-developers.com/z3-compact/help/sony-xperia-z3-compacts-display-peeling-t3156347
Dinkec27 said:
Could I use something like superglue or something similar to that?
Click to expand...
Click to collapse
Nope I wouldn't do that, as super glue is not flexible. I have glued both screen and back glass with B7000 adhesive (most repair shops use it specifically for displays) and it hasn't moved since. That was done some 4 months ago. If you put enough glue on the frame (be careful not to leave empty spots, cover the complete frame with glue), of course avoid dripping of the sides into the frame, I am sure that it won't peel off again, especially the back glass.
I am waiting for new screen to arrive, so I'll have to re-do everything again, of course with B7000.
Dinkec27 said:
Could I use something like superglue or something similar to that?
Click to expand...
Click to collapse
Never use superglue, it will not last long and will ruin your phone, as superglue's main ingredient disintegrates plastic...
I've also used red 3m tape, does not hold!
Bought B7000 glue, will use it once my new battery arrives, so using useless 3m red tape in the mean time...
-Update-
B7000 Glue works!!!
I heavily flash, test etc. and no matter how hot the phone gets, it's sealed and does not reopen.
I cleaned the surfaces, I applied the glue, and did not care about making a mess (the glue is easily removable for future repairs) and did not care about it oozing out either, just made sure that it covered that border.
I did not use any heat, and it was still cold here.
I then used clothes pegs, 3 on each edge (I was worried about too much pressure, but it was not an issue)
I did not turn my phone on at all, and waited for 48 hours, before removing the pegs then turning it on.
Please note: the z3c is bendable, especially in jeans pockets, I use an anodized bumper to keep it straight. And using tempered glass on both sides is recommended.
***I did however buy a new battery, as my previous battery seemed fat, and I also removed the nfc sticker, but not sure if that is necessary.