I was told by Jide support to follow these instructions:
Unfortunately, I cannot link to the instructions due to XDA's policy. Please search Jide support for the article titlted:
"What should I do if my Remix Mini is stuck in boot loop?"
Note that I am not presented with a message to hit F2 at the boot screen, so I assume I must use the more involved set of instructions described at the link above. With this in mind, I would like to get a recommendation on a USB-A Male to USB-A Male Cable. I have never purchased one before. Some that I have come across indicate they are not to be used for data transfer. I assume this is what I need to do, in this case.
@Kurtois
Any normal USB-A male to male cable will work. By normal I mean data cable, not a power cable (missing data wires).
There you have it on ebay
The article @Kurtois mentioned: What should I do if my Remix Mini is stuck in boot loop?
Related
Does somebody know yet if this device needs pin4 and pin5 connected (ground) for fast-charging on micro-usb?
On my kaiser I needed to connect these two to be able to charge in my car with my standard USB-charger.
To keep this charger as a universal charger (hope its 2 Amperes won't fry my HD2), I need to buy new cables or a mini-usb to micro-usb adapter and might need to modify them.
I noticed that the battery on my kaiser was getting fairly hot on this 2amps. Is there a protecting circuit, or is this in a safe range for those batteries?
amperes of you charger are max current, wchich you cat have from the charger... it is all about, how much leo will take it is about voltage...
and sorry, no idea about this connectivity... if you will tell me, how to check this, i will check it for you...
So, if I understood correctly, the device determines how much Amps to be drawn?
If you take the wall-charger and you look onto the micro-usb plug:
Code:
_____________
\ , , , , , /
\_________/
PIN: 5 4 3 2 1
For a Kaiser device to fastcharge , pin 5 and 4 must be connected together.
On normal USB-cables (micro and mini) for data, pin4 has no function, it isn't even wired in the cable.
Do you have a volt-meter to check this?
Thanks!
USB A male to micro USB A male cable versus USB B cable?
Hello guys,
I bought my HD2 yesterday ! I am very happy with it.
I would like to buy 2 more cables on ebay (1 for the office, 1 for home).
Should I buy the
- USB A male to micro USB A male cable
OR
- USB A male to micro USB B male cable
I am a bit confused here.
I see 2 types of cables on ebay, not sure which one to buy!
Any ideas?
Thanks
If my assumptions are correct, and the cables work like on the Kaiser device, it's:
- USB A male to micro USB A male cable (for fast-charging, works with generic-usb car charger - NO data connection)
edit: WRONG, because micro-A-plug is not compatible with micro-B-socket.
- USB A male to micro USB B male cable (for data-connection and slow USB-charging)
Still needs confirmation by an HD2-user, but I don't think HTC changed something going from mini to micro-plug. (I think they dropped EXT-usb design for having an extra 3,5mm headset-jack instead. - but that shouldn't confuse you)
Well, not exactly:
Type A is to be plugged into host-device (the one supplying power to the other device, usually the charger or your computer), whereas type B is to be plugged into the target device (in this case, the HD2).
This typology exists to prevent you from linking two power suppliers at both ends of the cable...
So what you need is a "USB Type A to Micro USB Type B" cable
That's the original USB-specs, you are referring to.
Mini/micro-A-plugs are using pin4-to-ground by these USB-spec, for electronically differenciating these.
What I wanted to pinpoint, is that HTC decided to mark pin4-to-ground for detection of their charging equipment.
And since micro-A plugs fit into micro-B sockets, you should be able to use a "USB A male to micro USB A male cable" for your charging needs (without modifying your micro-B cable, which can be quite tricky because of its size)
edit: I was wrong with that, it's the other way round, sry. Does the HD2 have a AB-socket then? I believe it's a regular B-socket.
Then if I stand correctly, you will still need a special modified micro-B-cable for charging.
To make it even more difficult, HTC-design does not charge the Kaiser with a regular mini-b-cable on a car-charger, because there was no data-signal on it.
My intention of this thread was asking, if this behavior has changed when going from mini to micro-usb design, and is still an unanswered question.
sayborg said:
Hello guys,
...
I would like to buy 2 more cables on ebay (1 for the office, 1 for home).
Should I buy the
- USB A male to micro USB A male cable
OR
- USB A male to micro USB B male cable
I am a bit confused here.
I see 2 types of cables on ebay, not sure which one to buy!
Any ideas?
Thanks
Click to expand...
Click to collapse
...same for me. may I have a clear and "safe" answer for dummie?
- USB A male to micro USB A male cable
OR
- USB A male to micro USB B male cable
Thanks a lot.
only USB-B-male fit into the device, boy!
Well, I've seen unboxing videos now, and the wall-charger ... is a normal-USB-plug-in device like a car-charger. Seems that my intention of this thread is obsolete.
I just wanted to share what I'd done for my streak in order to quit carrying a cable around everywhere. This is just a quick outline of what I did and supplies I used to make it.
Disclaimer:I am in no way responsible for your warranty getting void, phone blowing up starting ww3 or any other faults that may be the result of attempting this
Parts list:
1x streak usb cable
http://www.ebay.com/itm/16065922734...NX:IT&_trksid=p3984.m1497.l2649#ht_500wt_1286
1x micro usb to mini usb adapter
http://www.ebay.com/itm/25098693990...X:IT&_trksid=p3984.m1497.l2649#ht_3016wt_1035
1x old dvd case
5 minute epoxy
Optional:
small piece of carbon fiber vinyl
what to do:
-cut micro usb out of its rubber/plastic shell
-desolder all the wires
-cut the streak cable close to pdmi connector
-refer to this site for usb diagram, make sure to note that there's one pin that gets skipped over on the micro usb adapter
http://pinouts.ru/SerialPortsCables/usb_cable_pinout.shtml
-solder wires accordingly refer to my pictures if you get lost (the pdmi cable comes with all the wires correctly color coded)
-plug into streak and see if it works
-if everything works proceed to make a plastic shell for it out of dvd case
-use a little bit of epoxy to mount everything and keep it from sliding around
end result should look something like this
http://www.youtube.com/watch?v=rnLv5UIocW8&feature=youtu.be
Hi I'm not trying to negate the value of your guide in any way. I think a permanent mod to a compatible connection makes a lot of sense, especially if one never plans on using a Dell Streak 7 dock. However, if you're not that motivated and or aren't willing to brick your device this is a great $8 solution: http://www.ebay.com/itm/140853176551?ssPageName=STRK:MEWNX:IT&_trksid=p3984.m1439.l2649.
The cable you linked to wouldn't work, because the jack on the non-PDMI end is a USB A female connector, which accepts the end of the USB cable (USB A male) that normally plugs into the laptop or PC itself. To make it as useful as the DIY adapter the OP mentioned would require you to dismantle the host adapter and replace the USB A female jack with a MicroUSB B female jack.
PDMI connector to mini usb connector
Hello man. My name is Mario. I come from Italy. I'm a psychologist,but on the spare time I like to play with linux & mobile & tablet & technology in general. I was searching for a OTG adapter that was able to recharge my nexus 10 and at the same time that accepts an external sd card and someone has suggests this to me :
eKit 4 in 1 Data Sync Connection Kit For Samsung Galaxy Tab 2 10.1 & Note 10.1
you can read the full story here :
http://android.stackexchange.com/que...-the-same-time
the problem is that I haven't read very well what he says and I haven't understood that it is not good for the nexus 10. For this reason I have tried to search a way to convert the PDMI connector to a mini usb connector and I have found this thread. I would like to ask you if I can make the same thing that you have done and if you can tell me which electric modification I have to make to the board of this connector to convert it as a mini usb connector. Thanks.
Hi all,
I recently bought a female to female usb adapter hoping to use it along with the original charging/data cable to get USB host on my phone. It doesn't appear to be working. I have tried several peripherals (flash drive, keyboard etc.).
Is the data cable for the Atrix HD physically different from the OTG cable? I had heard that was the case for another device.
Edit: Sorry, I didn't mean to post this in general. Could a mod please move this to Q&A.
Please keep questions to the Q&A section
Sorry, I meant to post this in Q&A. Could a mod please move this. Thanks!
Micro USB plugs actually have 5 pins whereas the standard has 4. So pin 4 (called the ID pin) is left floating on your normal data cable. However, on an otg cable or adapter, pin 4 is shorted to pin 5 (ground) before everything goes to the rest of the cable. When the phone detects the short on the ID pin, it activates the host function.
You can find cheap adapters that short the pins for you or you can modify your own cable by hacking off the housing on the micro side and soldering a jumper between the pins. Also, for accessories to work, you'll likely need a powered USB hub since the phone won't supply the power for them (at least that's the way in my experience).
Hope this helps. Otherwise, let me know if you have more questions. If you google USB host or USB otg, you'll probably find some good stuff.
Sent from my MB865 using xda app-developers app
Thanks a lot! That totally answers my question. I'm just going to buy an OTG cable.
My problem is simple, i'm tethering my Wifi Nexus 10 to my Galaxy S3 and the S3 just doesn't have the staying power of the tablet and the AP is battery intensive.
I have considered:
Extended battery (unofficial) - don't want the bulk.
Extended battery (official) - not cost effective.
The other option would be usb otg and charger cable but I'd like a single cable if possible.
To make it clear - I'm looking for a double ended micro usb (B) cable.
If anyone knows of a reason this wouldn't work please do say
You could use this adapter with your original cable to see if it dies the job.
http://www.ebay.com/itm/Right-Angle...006572?pt=PDA_Accessories&hash=item27ccd180ac
I have the same setup (nexus10 and s3) let us know if it does work.
You could try monoprice.com. I get all of my cords and such from them.
eBuyer tend to be pretty good for this stuff.
Just FYI, I tried this using an OTG adapter and a standard USB-A to USB-B micro cable. Depending on which side I plug the OTG adapter into, the S3 charges the Nexus (when the adapter is plugged into the S3) or vice versa (when the adapter is plugged into the N10).
EDIT: It would be interesting to try though what would happen if one was to connect the four pins (VCC, D+, D-, GND) directly to one another, with the ID pin being left unconnected (since that is what a Micro-B to Micro-B cable would most likely do). My guess is that nothing will happen, since neither of the devices assumes a master/slave state and so it doesn't know that it should supply power to the other device. I guess I need to order some Micro-B plugs at Digi-Key and whip up a cable...
--fbrozovic
I like to use a lot of accessory with my op3, so I need some light on this.
1. Does the male type-c to female usb-a adapter work on those 1tb hardrive with rw functionality?
2. Does using male type-c to micro usb-b adapter pair with micro usb-b otg cable work?
3. Does using male type-c to male type-a cable(the normal type-c cable) connected with usb-a female to usb-a female works like an otg adapter?
4. Does usb hub connected with the above configuration that connect more than 2 peripherals work?
5. Does usb generation(usb 3.1 to 2.0) matters at all?
Sorry I'm asking a lot but I can't really test it out myself with stuff from the Benson safe list as amazon is not an option for me, and my recent purchase of micro usb-b otg pair with type-c adapter fail so some help is appreciated.
You should send an email to the support w/ all your questions actually
Cheers.