I posted this earlier, and received some help from oohaylima. I had to take some time off and it got away from me, but I still need help. I've read through hours of info. here but haven't been able to find an answer. A few posts were close, but the links they provided were broken or the pages they referred to had been taken down.
1. Since I can only access the phone via wifi, can I still rescue the phone, or can I do that using the SD card only (the links were no good in the post similar to this,)?
2. Since this last post, I did reset the phone holding the Home and Power buttons, now I get an error code 67 whenever I turn it on. Something concerning a User name and Password for a sprint account.
3. The phone won't activate with my Boost Mobile account, I can not place or receive calls with it.
4. My experience so far is limited to rooting a couple of phones and installing CM ROM's through instructions and guides here at xda and at the CM forum.
5. I would like to be able to flash CM onto the phone, not the stock version it came with.
To save time I have copied the last post here...
"I bought a second hand Sprint Hero cdma. ($12.50) It had the stock ROM, but also had BusyBox Pro and Superuser installed. Upon checking, su wasn't working,and BBPro gave a message that the phone was improperly rooted. Upon checking with RootChecker v 1.3 I got the following info from the table:
SU
su found
{/system/bin/, /system/xbin/}
Root Access
no access
UID/GID
uid=10084(app_84)
gid=10084(app_84)
group=3003(init)
UNIX UTILS
toolbox
/system/bin/toolbox
PATH
/system/xbin
/system/sbin
/sbin
//system/bin
Root Check Lite gave the message:
Your phone is rooted.
Your phone does not have superuser access.
I tried to root it again with superoneclick but it hung up on the second line. I then discovered that the phone won't connect via USB to mount the phone. My WIN 7, 64 bit HP won't read anything from it except wirelessly via Wondershare MobileGo. But, it does charge okay. (I have an old Samsung Conquer which functions okay via USB on my PC.)
The Firmware version, etc., is as follows:
Firmware: v 2.1 update 1
Baseband:v 2.42.02.10.29
Kernel: v 2.6.29.-ba77cfo3
[email protected] #1
Build: 2.32.651.2.CL282911 release-keys
Software: 2.32.651.2
PRI v: 2.65_003
PRL v: 11117
EDIT
I guess I am asking how do I re-root properly...or un-root then re-root. "
Thanks in advance to oohaylima and all,
Mike
What is needed is to flush the phone and start from scratch. What's your status on this now? I know it's been a couple of weeks.
oohaylima said:
What is needed is to flush the phone and start from scratch. What's your status on this now? I know it's been a couple of weeks.
Click to expand...
Click to collapse
I would still like to go thru with it when things on your end get under control.
Thanks for your message, I was hoping nothing too serious was going on with you!
Mike
Hi everyone,
I own a Motorola Moto G2 (XT1068, dual sim) that came used with Android 6.0 on it.
I installed TWRP (twrp-3.0.2-3-titan.img) on it but failed to root Android 6.0 as well as 5.0 for whatever not yet understood reason. I don't do Android development for a living but I'm an IT professional, so handling adb and fastboot as well as reading and understanding instructions isn't a problem.
I flashed stock Android 4.4.4 (RETDEALL_XT1068_4.4.4_KXB21.85-14) which I successfully rooted by installing SuperSU via TWRP.
Next I updated SuperSU, verified that root access is indeed working and installed FlashFire, which I hoped to use to install OS upgrades, possibly without losing root. FlashFire is new to me (as of yesterday), everything else mentioned up to here is not.
I used the "Flash ZIP or OTA" action from within FlashFire and the previously downloaded update file in the /cache directory. I can't reproduce the file name since the phone is currently unusable and I didn't write the file name down prior to using FlashFire.
The state of the phone after this unsuccessful attempt was that of a broken USB device, i.e. unable to even register as whatever type of USB device. I learned that this can be fixed by holding the power button down for more than one minute, after which I managed to
get the phone to be shown as working "RELINK HS-USB QDLoader 9008" USB serial device in Windows 7 device manager.
I used the information in these two threads:
http://forum.xda-developers.com/moto-g/help/how-to-unbrick-moto-g-falcon-t3394788
http://forum.xda-developers.com/moto-g/help/how-to-revive-hard-bricked-moto-g-t2833798
Since I started with Android 4.4.4 trying to upgrade to 5.0, I had hoped that the blank flash package for one of these Android versions would help fix my problem, but as of now, this doesn't seem to be the case. At the end of the blank flashing process, I get the message
FAILED <blank-flash:sdl-transfer-image:sdl-hello: error sending packet>
After that, the phone still has a black screen and cannot boot into anything. Repeating blank flash works after resetting whatever part of it is still working by holding the power button down for about 30+ seconds.
Is there anything obvious (or maybe even not so obvious) that I missed?
Thanks for reading and any help and/or pointers in the right direction.
hey , contact me on pm
salkollizz said:
hey , contact me on pm
Click to expand...
Click to collapse
Did you solved the problem of hard brick of Moto G 2014?
Can someone please help. I'm getting desperate now. I flashed a Nougat build a little while ago but had some issues with Bluetooth and NFC so I flashed back to the original firmware using the dload folder and 3 button method. The installation seemed to go through fine but get's stuck booting at the vodafone logo. It then takes me into eRecovery where it attempts to download latest version over wifi but fails. I don't really know where to go from here because I can't access the internal sd card because the phone won't boot. I can access fastboot but don't really know what to do from there.
stevemacer10 said:
Can someone please help. I'm getting desperate now. I flashed a Nougat build a little while ago but had some issues with Bluetooth and NFC so I flashed back to the original firmware using the dload folder and 3 button method. The installation seemed to go through fine but get's stuck booting at the vodafone logo. It then takes me into eRecovery where it attempts to download latest version over wifi but fails. I don't really know where to go from here because I can't access the internal sd card because the phone won't boot. I can access fastboot but don't really know what to do from there.
Click to expand...
Click to collapse
Stevemacer10 Hello, I hope to be keen to help, because it happened to me the same thing, with two days of stomach ache for it. In wanting to load Android on my Nougat Huawei P9 Plus VIE-C02, with VIE-L09C605B354 and VIE-L29C185B320 I went into semi-brick or brick, or was only in bootloader, the screen with the green man to speak. No avail various ways, including via microSD-Fastboot or ADB to do restart your phone. Then, to my previous experience with a Huawei tablet, I logged on to the 'https://www.dc-unlocker.com/' site, and essend already registered, I bought 15 credits (15 Euros), for the 'option' DC Phoenix Firmware write ', valid for 72 hours, in addition to the program and downloaded the' DC program Phonix v29 '(https://www.dc-unlocker.com/DC-Phoenix-flash-repair-tutorial) following the related tutorial. Obviously procured the original firmware 'VIE-L09C02B133' or even lower versions, you'll have to unpack in a folder of your preference. Unfortunately, despite having used with DC Phoenix the original firmware was always also blocked me. At that point I wanted groped with a firmware that you can find on the same site of the DC-Unlocker (https://files.dc-unlocker.com/user.html?v=files/57694006a60d7) by downloading the firmware 'VIE_AL10B_M00A063_Factory_firmware_China_Nonspecific_Android_6.0_EMUI_4.1 .dgtks', which I loaded with DC-Phoenix on the phone. Rebooting of a minimal mode of andorid, I did not see well either. I went back into bootloader, as well as devone be made the previous steps that I have already described to you, and this time with DC-Phoenix I loaded on the phone firmware L09C02B128 and everything went well. Attention and keep in mind that just as I happened to me, the serial number of your phone is changed, to me has happened in '0123456789ABCDEF' and there was no way to change it, so as, while having the unlocked bootloader can not longer charge the TWRP recovery in order to then have root permissions. Until reading the paragraph '(Optional) Phone numbers REPAIR', I went to that point on the site 'http://hcu-client.com/'. Also here are sadly bought 8 credits (8,00 Euro) in order to work with the program 'HCU-Client v1.0.0.0115', you need to download and unpack, then follow the various instructions, which are not difficult when you have to be walked through the modding, otherwise you do even more damage. Let me know what you did and how it went to the method. I hope also good for you. In summary we want Euro 15 for Phoenix whose duration of operations applies to 72 hours and 8 Euro per HCU-Client, it can only use this for 24 hours.
P.S .: Obviously if you follow my instructions and all these signs you do so at your own risk, esonerandomi from every possible and accidental deterioration of the situation and the damage to your phone. Sorry for my English, whose translation has made Google translator.
---------- Post added at 12:59 AM ---------- Previous post was at 12:33 AM ----------
I wanted to say that the change of the serial number does not work well. The serial number has been changed from what I've shown you above, but was not put one I added that I had from the sales box. I write support and maybe let you know what they tell me. See you soon.
Hi Grlshia,
Thanks for getting back to me. It's such a minefield playing with all these different regional variants. I have though, managed to get it completely fixed. I just gave in and took it into the local Vodafone store and fortunately there happened to be one of the tech experts in there that owned a P9. He took it off me and within about 5 minutes he had completely restored it. He told me he just did a factory reset by holding down vol+ and power. I'm sure I had tried this myself to no avail previously but that's what he said he did.
stevemacer10 said:
Hi Grlshia,
Thanks for getting back to me. It's such a minefield playing with all these different regional variants. I have though, managed to get it completely fixed. I just gave in and took it into the local Vodafone store and fortunately there happened to be one of the tech experts in there that owned a P9. He took it off me and within about 5 minutes he had completely restored it. He told me he just did a factory reset by holding down vol+ and power. I'm sure I had tried this myself to no avail previously but that's what he said he did.
Click to expand...
Click to collapse
Stevemacer10 hello, I'm glad you've solved the problem. Unfortunately I'm still fighting because, for now I can only and even to load its firmware, but if you want to try to load the TWRP recovery for later obtain root permissions, it always fails. From what seems to understand me and certainly due to the fact that the bootloader unlock code now is different from what I have, because as I told you the serial number has changed and if I request a new unlock code, it stops notiziandomi the procedure that there is inconsistency between this number and the IMEI. For now I do not know what to do and how to proceed. I hope that over time can still solve my problem. A good evening to you :good:
i'v been throw it
after updating my p9 plus with a firmware that is not sutable to my area
my phone restarted and ask for an account wich ok but the problem was that the software not working properly and missing a keyboard.
and will not go to recovery mode to try another software.
this sloved by downloading a sutable correct software and unzip it into an SD card folder (i create) called dload, then swich off the device and turn it back on while holding three bottons (power+v up+v down) 10 to 15 sec. and the phone directly read from the SD card and start updating a new firmwarw.
try it.
it success with me , hope it work wth u
Hi guys,
I've bought an P9 and wanted to get rid of the booting screen with the resellers logo.
So I thought I'd be smart, unlocked the device, flashed TWRP 3.1.1-1-eva.img onto it. Got an SuperSu-file and tried to install it...
I never got to experience the rooted version. Got stuck in a bootloop, somehow got out of it. Logged in, saw an green SuperSu-app, opend it and it saidthe device has to be rooted to use the device, ergo i failed to root it. [Forgot some steps here] and I found myself in another bootloop. A friendly guy suggested to flash these 2 files
[Link-Removed]update.zip
[Link-Removed]update_data_full_hw_eu.zip
which I did with dload. After that, I was still in a bootloop, but with WipeCache I was able to get myself back into my phone [hooraay].
The happyness-phase was a short, because i soon found out, that it doesn't have an keyboard (only googleVoice, should be fun to type in a wifi-password). Huawei-ID tab is also missing (usually located below Accounts), Update Phone, which was between Advanced Settings and About Phone is also missing, and bluetooth doesn't seem to work. That's when I noticed that I'm on NRD90M test-keys build.
After reading some threads here i downloaded rollback from huawei (for west-europe). Now I'm on C900B300 but all settings still missing.
Now I'm here crying for help.
Any suggestions? Please?
Ryan
You got to rebrand your phone.
movizdb said:
You got to rebrand your phone.
Click to expand...
Click to collapse
do you mean, that i have to put the bootlogo back into it?
could be a meanie to do, because it's a swiss brand and I don't think that there's a version here for me to use.
//or do an OEM-Flash, which worked
Hi,
I always found it saddening to notice EZCast5G (the "original") is updated at first and their knock offs are updated way later (as of writing this, there is 16602000 for EZCast5G, 16403000 for MiraScreen5G).
The update tool let's you easily analyze the update process. And if you fake the reply from this URL with (for example) miniweb to always dish out latest EZCast5G firmware then your knock off will become an original.
These are the requests made for a legit EZCast5G and a MiraScreen5G:
Code:
[COLOR="Purple"]curl http://www.iezvu.com/upgrade/ota_rx.php -d "{\"version\":1,\"vendor\":\"ezcast5g\",\"mac_address\":\"authorshxj\",\"softap_ssid\":\"000000-00000000\",\"firmware_version\":\"16602000\"}"[/COLOR]
[COLOR="Blue"]curl http://www.iezvu.com/upgrade/ota_rx.php -d "{\"version\":1,\"vendor\":\"am8252_nand_mirascreen\",\"mac_address\":\"authorshxj\",\"softap_ssid\":\"000000-00000000\",\"firmware_version\":\"16403000\"}"[/COLOR]
These are the official replys where you need to always dish out the first one and the update tool will do the rest:
Code:
[COLOR="Purple"]{"ota_conf_file":"http://cdn.iezvu.com/upgrade/ezcast5g/ezcast5g-16602000.conf","ota_fw_file":"http://cdn.iezvu.com/upgrade/ezcast5g/ezcast5g-16602000.gz","ota_enforce":true}[/COLOR]
[COLOR="Blue"]{"ota_conf_file":"http://cdn.iezvu.com/upgrade/am8252_nand_mirascreen/am8252_nand_mirascreen-16403000.conf","ota_fw_file":"http://cdn.iezvu.com/upgrade/am8252_nand_mirascreen/am8252_nand_mirascreen-16403000.gz","ota_enforce":true}[/COLOR]
When I opened mine it even read "5G EZCAST V1.4" on it - so I was pretty sure it should work. And it did. So for $17 one year ago I got myself a neat working EZCast5G. The MiraScreen5G gets into bootloader mode by pressing the one and only button right when you plug it into USB - no need to shorten pin 19 and 20 of the AM8252.
Thank you.
Some questions.
How to use this curl command with miniWeb?
Hi,
BUMP
No honestly, could you elaborate how this works ? Have 2 MiraScreen5G dongles...
Ender
Hi,
with some help from Chatty and another forum i got it done !
First i needed to add a line to my hosts file:
(On windows its found in C:\Windows\System32\drivers\etc)
Code:
127.0.0.1 www.iezvu.com
Then i downloaded miniweb and created a file containing the desired server answer.
Miniwebs web root resides in the "htdocs" folder by default, so i created a folder named "upgrade" and in that folder a file named "ota_rx.php.
I edited that file to contain this text:
Code:
{"ota_conf_file":"http://cdn.iezvu.com/upgrade/ezcast5g/ezcast5g-16602000.conf","ota_fw_file":"http://cdn.iezvu.com/upgrade/ezcast5g/ezcast5g-16602000.gz","ota_enforce":true}
I fired up miniweb with the parameter "-p 80" to listen on the stabdard web port.
THEN i started the EZ Updater app, connected my dongle in Flash mode and VOILA it detected the version i wanted it to detect.
So it flashed (took forever with several loops) my MiraScreen5G to a EZCast5G !!!!
After that initial update the dongle detected a newer version and updated okay.
Please note that AFTER the update you cannot get into flash mode by simply pressing the key. I assume that key is not considered existing anymore since the EZCast5G has none as well
So for further flash-fun we need to short the Pin like its descived by Chatty !
THANKS Chatty & all,
Ender
Just opened a K6 mirascreen and found these
nanya nt5cb64m16fp-dh 128mb ddr3 ram
am8272
samsung k9f1g08u0d 16mb flash
the pcb reads S?-EZCAST-8271-V2F
im unable to find a suitable firmware for it and no idea how to enter download mode....
---------- Post added at 06:02 PM ---------- Previous post was at 05:35 PM ----------
the firmware says 1.3707.11 btw
Hey Guys,
If someone knows, please share the knowledge.
Few Months ago when I was updating the firmware, my Dongle died due to power cut.
after reconnecting my PC couldn't read the version of my dongle. Today I wanted to revive my Dongle But have no to little experience on the Windows Debugging. I know my Dongle is not dead and it has no firmware, I also know that EZCast Repair tool can Flash the Firmware to it, I can download the firmware using the OP, I can also see that The App has options for Manually flashing the Firmware.
But I don't know how and what to do to access the areas shown in the Screenshot.
anyone please help me and point me to right direction.
Thanks in Advance.
SweenWolf said:
Hey Guys,
If someone knows, please share the knowledge.
Few Months ago when I was updating the firmware, my Dongle died due to power cut.
after reconnecting my PC couldn't read the version of my dongle. Today I wanted to revive my Dongle But have no to little experience on the Windows Debugging. I know my Dongle is not dead and it has no firmware, I also know that EZCast Repair tool can Flash the Firmware to it, I can download the firmware using the OP, I can also see that The App has options for Manually flashing the Firmware.
But I don't know how and what to do to access the areas shown in the Screenshot.
anyone please help me and point me to right direction.
Thanks in Advance.
Click to expand...
Click to collapse
Have you found any help? I have updated to EzCast firmware but now my dongle doesn't appear on wifi list and on TV only shows EzCast logo..
dLightas said:
Have you found any help? I have updated to EzCast firmware but now my dongle doesn't appear on wifi list and on TV only shows EzCast logo..
Click to expand...
Click to collapse
No I found no help.
All I need is access the flashing area.
I had 2 tools laying around (think i deleted those)
One was older and directly opened the firmware flashing page, but that doesn't have the partition table of My Dongle.
And the other tool which have the partition table, opens on main page (which is automated and does nothing)
If somehow i could access the firmware flashing area on the newer tool then I could revive my dongle.
If your dongle contained older chip of Action Electronics (earlier than 52) then the older tool can flash your dongle.
nostupidthing said:
Just opened a K6 mirascreen and found these
nanya nt5cb64m16fp-dh 128mb ddr3 ram
am8272
samsung k9f1g08u0d 16mb flash
the pcb reads S?-EZCAST-8271-V2F
im unable to find a suitable firmware for it and no idea how to enter download mode....
---------- Post added at 06:02 PM ---------- Previous post was at 05:35 PM ----------
the firmware says 1.3707.11 btw
Click to expand...
Click to collapse
Today there was a firmware upgrade available and after updating it's dead any help
Edit: OK I was able to flash using this tool (https://mirascreen.com/pages/repair-tool-for-chip-8272-products) but still nothing comes up...
Edit 2: The new firmware is 1.10505.52
MiraScreen G9 Plus
=================
[Name Model] , [Vendor String] , [Supported of the "MiraScreen G9 Plus"]
(EZCast5G) - ezcast5g - Not supported
(MiraScreen5G) - am8252_nand_mirascreen - Not supported
(EZCast 2H) - am_8270_ezcast4k-dongle_ezcast2h - Not supported
(EZCast TX) - am_8270_ezcast-tx_nand-std - Not supported
(EZCast 2) - am8271_ezcast2K - Not supported
(EZCast 4K) - ezcastduo - Not supported
(EZCast Band1) - am_8271_ezcast2-dongle_b1 - Not supported
(EZCast Ultra) - am_8275_ezcast-dongle_ultra - Not supported
(AnyCast M100) - sage_8272_mirascreen-dongle_anycast - Supported
(MiraScreen K6) - am_8272_mirascreen-dongle_std - Supported
Check Firmware over http api:
https://api.ezcast.com/api/firmware...mirascreen-dongle_std&firmware_version=1.10.3
https://www.ezcast.com/service/ota/..._8272_mirascreen-dongle_std&rx_version=1.10.3
Current official firmware version for the "Mirascreen G9 Plus": 1.10505.61
Do you know others? I would for the model "Mirascreen G9 Plus"?
"Mirascreen G9 plus" supports alternative Firmware (Firmware tested on the "MiraScreen G9 Plus"):
FW v1.13610.47: http://cdn.iezcast.com/upgrade/am_8...dongle_std_official-1.13610.47-0x99A7C4FD.img
Flash Tool: https://cdn.shopify.com/s/files/1/0017/6553/9884/files/MiraScreen_8272_Repair_Tool.rar
FW v1.10505.3: http://cdn.iezcast.com/upgrade/sage...gle_anycast_official-1.10505.3-0x937AC2AD.img
Flash Tool: https://cdn.shopify.com/s/files/1/2427/2515/files/AnyCast_M100Repair_Tool.zip
Small modification of Wi-Fi antenna:
https://forum.xda-developers.com/t/mirascreen-g9-plus-hw-fw-mods.4391225/
Hi to all, can anyone help me please with my EZ mira app and dongle device associated with it (miracast).
I have tried to upgrade software for my miracast device thru EZmira app, but suddenly Commercials pop up and my upgrade has been stuck at 10% and won't go further , worse after disconnect or reset there is no signal at all anymore it does not start /boot nor emmit wifi signal. What to do (because of stupid commercial)??
I tried to reset device several times but nothing, tried reseting thru PC but it does not load or Windows does not recognoze device to upgrade it thru web tools.
Please can anyone get that firmware back in my device and restore it .
Much appriciated and thanks in advance!
Anton TNT said:
Hi to all, can anyone help me please with my EZ mira app and dongle device associated with it (miracast).
I have tried to upgrade software for my miracast device thru EZmira app, but suddenly Commercials pop up and my upgrade has been stuck at 10% and won't go further , worse after disconnect or reset there is no signal at all anymore it does not start /boot nor emmit wifi signal. What to do (because of stupid commercial)??
I tried to reset device several times but nothing, tried reseting thru PC but it does not load or Windows does not recognoze device to upgrade it thru web tools.
Please can anyone get that firmware back in my device and restore it .
Much appriciated and thanks in advance!
Click to expand...
Click to collapse
Do you have a specific device?
Manufacturing publishes tools to restore some firmware here:
EZCast: https://www.ezcast.com/repair
MiraScreen:
https://mirascreen.com/pages/repair-tool-for-chip-8268-8252-products
https://mirascreen.com/pages/repair-tool-for-chip-8272-products
AnyCast:
https://any-cast.com/pages/repair-tool-for-chip-8268-8258-products
https://any-cast.com/pages/repair-tool-for-chip-8272-products
renda-l said:
Do you have a specific device?
Manufacturing publishes tools to restore some firmware here:
EZCast: https://www.ezcast.com/repair
MiraScreen:
https://mirascreen.com/pages/repair-tool-for-chip-8268-8252-products
https://mirascreen.com/pages/repair-tool-for-chip-8272-products
AnyCast:
https://any-cast.com/pages/repair-tool-for-chip-8268-8258-products
https://any-cast.com/pages/repair-tool-for-chip-8272-products
Click to expand...
Click to collapse
I have trided this solution , but no prevail, like device is dead, nothing just blank screen after failed update
Anton TNT said:
I have trided this solution , but no prevail, like device is dead, nothing just blank screen after failed update
Click to expand...
Click to collapse
This procedure works 100%, completely restores the firmware. If only an incorrect update occurred.
renda-l said:
This procedure works 100%, completely restores the firmware. If only an incorrect update occurred.
Click to expand...
Click to collapse
I'm not shure maybe I'm doing something wrong, but even windows doesn't recognize device
Anton TNT said:
I'm not shure maybe I'm doing something wrong, but even windows doesn't recognize device
Click to expand...
Click to collapse
Yes, of course, if the firmware is faulty, the device is not recognized and does not work. You must follow the Firmware Recovery Procedure. The device will most likely be repaired. Unfortunately, unless you specify a specific type, you can't be specifically advised on how to proceed.
renda-l said:
Yes, of course, if the firmware is faulty, the device is not recognized and does not work. You must follow the Firmware Recovery Procedure. The device will most likely be repaired. Unfortunately, unless you specify a specific type, you can't be specifically advised on how to proceed.
Click to expand...
Click to collapse
It is MIRACAST, I dont know chip number but it is dongle type round shaped eith EZmira app controlled
Anton TNT said:
It is MIRACAST, I dont know chip number but it is dongle type round shaped eith EZmira app controlled
Click to expand...
Click to collapse
Set your device to Recovery mode according to the procedure and use the tool for chip 8268/8252 or 8272. If the response is "device connected", it is a given chip set.
renda-l said:
Set your device to Recovery mode according to the procedure and use the tool for chip 8268/8252 or 8272. If the response is "device connected", it is a given chip set.
Click to expand...
Click to collapse
on which side is pin 7 and 8 ? Chip on my board is square shaped and got pins on all sides. Just to be sure not to fry anything, which side is NAND memory
Anton TNT said:
on which side is pin 7 and 8 ? Chip on my board is square shaped and got pins on all sides. Just to be sure not to fry anything, which side is NAND memory
Click to expand...
Click to collapse
If your device has a button, first try to enter recovery mode, press the button and connect USB.
In the procedure is a photo of the MCU and these pins are shown.