Related
Hello,
after a couple of attempts at installing TWRP recovery, some successful, some not, a ROM reinstall and finally this last factory reset, my Huawei P9 phone is stuck at what appears to be boot or restart loop. It is interesting however that I am unable to turn off the phone at all and it's been like this for an hour. At first, TWRP recovery wouldn't boot but the OS would. Then I did factory reset and phone restarted. Since then it won't boot or turn off. When I hold the power button to turn it off, it vibrates once, then vibrates again and then Huawei logo is displayed. After that a message that says "Your device has been unlocked and can't be trusted." & "Your device is booting now..." which is normal since I unlocked my phone bootloader, but the problem is that it is just stuck there.
It stays there forever, screen on, phone on, can't restart because it comes back to the same point, can't turn it off since battery is impossible to take out... Any hope? I bought the phone a couple of days ago and this is really bad... Help!
Edit: In case someone else stumbles upon similar situation - after trying everything possible with these 3 buttons I had available (vol+- and power), I have managed to boot by (I THINK) holding the power button for 10 secs but releasing it really fast after the screen turns off and BEFORE the first vibration happens.
Edit 2: Now I have the same problem again and I can't seem to get the right button "combo" to pass the booting phase like I did some hour ago... Any ideas?
Edit 3: It appears that the ROM I have flashed caused problems with TWRP - after I got an SD card, managed to put stock ROM (http://forum.xda-developers.com/p9/development/stock-rom-dload-file-p9-eva-l09-b136-t3382818) on it and then did force upgrade, the phone booted successfully.
Step by step:
1) Drained battery to 0% and forced phone to turn off (otherwise it would vibrate twice and get stuck loading TWRP if I tried to turn it off using power button)
2) When I plugged it in and it got some battery power it started, avoided TWRP and regularly booted the OS (which was causing problems with TWRP in my case I think). If you don't have any OS, do not recharge or turn on your phone until you have prepared and put SD card into the phone
3) Downloaded and extracted the dload folder from the P9 stock ROM archive (http://forum.xda-developers.com/p9/development/stock-rom-dload-file-p9-eva-l09-b136-t3382818) to root directory of SD card
4) Unplugged and turned off the phone using OS Shutdown option
5) Turned it on by holding power, volup and voldown buttons together - "Your device has been unlocked and can't be trusted. Your device is booting now..." message appeared so I thought it was stuck again and was about to hang myself, but then the OS upgrade started (if it doesn't work right away, try restarting the phone with power, volup and voldown buttons held together again)
6) Upgrade was successful but the phone wouldn't boot without complete factory reset, after which it booted normally. Bootloader was relocked, then I updated to the latest stable EMUI (4.1.1) and life returned to normal.
BUMP
I can access Fastboot&Rescue mode and use abd (but phone is not rooted). Other than that I can't get to repeat what I did when I managed to boot the phone previous time this happened some hours ago... Can anyone post all volume+- and power key combinations which I can try?
Any other ideas more than welcome...
Guys can someone help with this. I'm having the same sort of issues. I have flashed an update and now I have lost touch on the screen. I can't even use twrp because the touch is not working.
Please can someone advise.
Sent from my SM-G928F using Tapatalk
Vernicht said:
BUMP
I can access Fastboot&Rescue mode and use abd (but phone is not rooted). Other than that I can't get to repeat what I did when I managed to boot the phone previous time this happened some hours ago... Can anyone post all volume+- and power key combinations which I can try?
Any other ideas more than welcome...
Click to expand...
Click to collapse
After getting an SD card (everything I did so far was using internal storage) and putting stock Huawei P9 ROM on it (Android 6 and EMUI 4), then shutting down (forced by draining battery) and doing force upgrade (vol+ and vol- held after power up) I have managed to (upgrade and) boot my phone and get it back to normal again. If anyone needs more detailed explanation on how I solved this, feel free to ask.
Open bootloader again, i had the same problem few days ago
Yes please vernicht. My touchscreen has stopped responding after flashing an update.app using DC Phoenix.
I really need to get the phone back to normal.
Thanks in advance
Sent from my SM-G928F using Tapatalk
nscxp2005 said:
Yes please vernicht. My touchscreen has stopped responding after flashing an update.app using DC Phoenix.
I really need to get the phone back to normal.
Thanks in advance
Sent from my SM-G928F using Tapatalk
Click to expand...
Click to collapse
Can you boot into OS? Please provide more exact details.
How I got out of the TWRP(?) boot loop: I couldn't take out the battery, but I have managed to drain it to 0% by letting the phone stay on for hours thus eventually shutting itself down. After that I have charged it and then powered it up. It didn't attempt to boot TWRP (no loop) but instead booted back the OS. After that I could regularly restart the phone and do all operations without getting stuck in loop, which allowed me to issue force upgrade command using hardware power up/down buttons.
Nope. I manage to flash it with DC Phoenix fully but it just keeps boot looping and going back to the Huawei logo. Then after that if goes into its recovery menu and the only my to use the menus is with the volume keys.
Sent from my SM-G928F using Tapatalk
nscxp2005 said:
Nope. I manage to flash it with DC Phoenix fully but it just keeps boot looping and going back to the Huawei logo. Then after that if goes into its recovery menu and the only my to use the menus is with the volume keys.
Sent from my SM-G928F using Tapatalk
Click to expand...
Click to collapse
Are you able to put files on your SD card? If yes, you can try putting stock ROM on it and then force force upgrading (hold vol+ and vol- together after power up). It should overwrite everything and boot up.
I have done this but it won't even force flash the stock rom. It gets to 5% and says 'system error'
I followed your suggestion to let the battery drain and then I charged it fully, but when charging it got to 1% and rebooted the phone into eRecovery.
I wish I could get this phone fixed and back to normal.
Sent from my SM-G928F using Tapatalk
nscxp2005 said:
I have done this but it won't even force flash the stock rom. It gets to 5% and says 'system error'
I followed your suggestion to let the battery drain and then I charged it fully, but when charging it got to 1% and rebooted the phone into eRecovery.
I wish I could get this phone fixed and back to normal.
Sent from my SM-G928F using Tapatalk
Click to expand...
Click to collapse
Did you use this stock ROM for P9 (if it's EVA-L09 like mine) or something else?
http://forum.xda-developers.com/p9/development/stock-rom-dload-file-p9-eva-l09-b136-t3382818
It worked fine with force upgrade for me, while some other ROMs didn't.
Do you have Wipe cache and data/factory reset options available in eRecovery, did you try that?
I'll try that. The only problem I have is my touchscreen won't respond under eRecovery. I have to use the volume and power key to navigate. Any idea what's happened there?
Sent from my SM-G928F using Tapatalk
nscxp2005 said:
I'll try that. The only problem I have is my touchscreen won't respond under eRecovery. I have to use the volume and power key to navigate. Any idea what's happened there?
Sent from my SM-G928F using Tapatalk
Click to expand...
Click to collapse
It will probably return to function after you restore to stock ROM. Until then you can use power button to select items in eRecovery if needed.
Btw I have edited my original first post in this thread with step by step guide on what I did in my case.
Thank you Vernicht for all your help.
I finally manage to get the phone fully working again. I also managed to get it changed from C900 to C432, lock the bootloader and join the beta.
Thank you so much again. It's very much appreciated.
Merry Christmas too
Sent from my SM-G928F using Tapatalk
Hi nscxp2005
how did you manage that?
i have the same Problem.
i have done a "Wipe Cache" and a factory reset.
i have copied the "update.app" from PauloBrien zip on a sd card in a folder named dload.
then i have done a Force flash -> it goes to 5% an says Invalid File.
when i look in the device with DC Phoenix it says it is a EVA-L09C900B136
Why have i done that?
My wive have the EVA-L09C432B136 and i updatet it OTA to Nougat.
i thought i could switch to that version to get the new Nougat but something went wrong......
thanks in advance and sry for my english =)
trx850 said:
Hi nscxp2005
how did you manage that?
i have the same Problem.
i have done a "Wipe Cache" and a factory reset.
i have copied the "update.app" from PauloBrien zip on a sd card in a folder named dload.
then i have done a Force flash -> it goes to 5% an says Invalid File.
when i look in the device with DC Phoenix it says it is a EVA-L09C900B136
Why have i done that?
My wive have the EVA-L09C432B136 and i updatet it OTA to Nougat.
i thought i could switch to that version to get the new Nougat but something went wrong......
thanks in advance and sry for my english =)
Click to expand...
Click to collapse
Did you manage to fix this issue??
---------- Post added at 10:55 PM ---------- Previous post was at 10:52 PM ----------
Hi Guys, hope you can help
I have got an P9 EVA-L09 which I tried to update to B378 but failed and now it stuck in a boot loop and won't recover using the phone.
I have tried to download the update mentioned above and doing a forced recovery on the phone Power + VOL+ + VOL- but no luck, gets 5% and fails.
Would like some help please.
Hello, I have the same problem, I tried to install Lineage 14.1 and it didn't work. Then i tried to go back to EMUI 5.0 and i just all fell apart. No i have no android on my P9 (cos i wiped all data and the system through TWRP 3.1.1.1), and now my touchscreen doesn't work. When i try to force install, it blockes on 5%. Anyone have any idea on how to fix it? Thanks
weineckcobra said:
Hello, I have the same problem, I tried to install Lineage 14.1 and it didn't work. Then i tried to go back to EMUI 5.0 and i just all fell apart. No i have no android on my P9 (cos i wiped all data and the system through TWRP 3.1.1.1), and now my touchscreen doesn't work. When i try to force install, it blockes on 5%. Anyone have any idea on how to fix it? Thanks
Click to expand...
Click to collapse
Inatall System via Srk Tool
Bricked my P9 while trying to remove branding.
Vernicht said:
Hello,
after a couple of attempts at installing TWRP recovery, some successful, some not, a ROM reinstall and finally this last factory reset, my Huawei P9 phone is stuck at what appears to be boot or restart loop. It is interesting however that I am unable to turn off the phone at all and it's been like this for an hour. At first, TWRP recovery wouldn't boot but the OS would. Then I did factory reset and phone restarted. Since then it won't boot or turn off. When I hold the power button to turn it off, it vibrates once, then vibrates again and then Huawei logo is displayed. After that a message that says "Your device has been unlocked and can't be trusted." & "Your device is booting now..." which is normal since I unlocked my phone bootloader, but the problem is that it is just stuck there.
It stays there forever, screen on, phone on, can't restart because it comes back to the same point, can't turn it off since battery is impossible to take out... Any hope? I bought the phone a couple of days ago and this is really bad... Help!
Edit: In case someone else stumbles upon similar situation - after trying everything possible with these 3 buttons I had available (vol+- and power), I have managed to boot by (I THINK) holding the power button for 10 secs but releasing it really fast after the screen turns off and BEFORE the first vibration happens.
Edit 2: Now I have the same problem again and I can't seem to get the right button "combo" to pass the booting phase like I did some hour ago... Any ideas?
Edit 3: It appears that the ROM I have flashed caused problems with TWRP - after I got an SD card, managed to put stock ROM (http://forum.xda-developers.com/p9/development/stock-rom-dload-file-p9-eva-l09-b136-t3382818) on it and then did force upgrade, the phone booted successfully.
Step by step:
1) Drained battery to 0% and forced phone to turn off (otherwise it would vibrate twice and get stuck loading TWRP if I tried to turn it off using power button)
2) When I plugged it in and it got some battery power it started, avoided TWRP and regularly booted the OS (which was causing problems with TWRP in my case I think). If you don't have any OS, do not recharge or turn on your phone until you have prepared and put SD card into the phone
3) Downloaded and extracted the dload folder from the P9 stock ROM archive (http://forum.xda-developers.com/p9/development/stock-rom-dload-file-p9-eva-l09-b136-t3382818) to root directory of SD card
4) Unplugged and turned off the phone using OS Shutdown option
5) Turned it on by holding power, volup and voldown buttons together - "Your device has been unlocked and can't be trusted. Your device is booting now..." message appeared so I thought it was stuck again and was about to hang myself, but then the OS upgrade started (if it doesn't work right away, try restarting the phone with power, volup and voldown buttons held together again)
6) Upgrade was successful but the phone wouldn't boot without complete factory reset, after which it booted normally. Bootloader was relocked, then I updated to the latest stable EMUI (4.1.1) and life returned to normal.
Click to expand...
Click to collapse
I have the same issue after flashing the rollback package from the official huawei site. The phone isn't rooted, it just had a branding for some odd reason. So I installed the C432B182 but somehow ended up with a C900B... firmware. So I installed the Rollback package C900B300 using the 3 button method. It said successfull but ever since I've been stuck in the same loop. At the logo. Trying to enter recovery mode (Volume Up + Power) or Force flash any of the firmwares (stock C432.. or rollback C900) doesnt succeed. It wont attempt. Only vibrates as you described and turns the screen off for a second before entering the same loop again.
How did you manage to enter the flash Menu??
Thanks in advance and hope you can help.
SherifSabet said:
I have the same issue after flashing the rollback package from the official huawei site. The phone isn't rooted, it just had a branding for some odd reason. So I installed the C432B182 but somehow ended up with a C900B... firmware. So I installed the Rollback package C900B300 using the 3 button method. It said successfull but ever since I've been stuck in the same loop. At the logo. Trying to enter recovery mode (Volume Up + Power) or Force flash any of the firmwares (stock C432.. or rollback C900) doesnt succeed. It wont attempt. Only vibrates as you described and turns the screen off for a second before entering the same loop again.
How did you manage to enter the flash Menu??
Thanks in advance and hope you can help.
Click to expand...
Click to collapse
Hello!
At me too such problem. When charging to sit at 0% and plug it into the charger, it immediately turns on and goes into the system, then the screen is worth a long logo. I have a phone EVA-L09C627B150.
Help me find my full version! Or I can use this version by reference https://forum.xda-developers.com/p9/development/stock-rom-dload-file-p9-eva-l09-b136-t3382818
Sorry for my English!
Hello everyone,
I bought a few days ago the Honor 5C and decided to root it. So I installed the TWRP (Nemo) using "fastboot", downloaded a ZIP of SuperSU and placed at the root of the internal storage. But when I try to enter recovery mode by using "adb reboot recovery" or by pressing the Volume Up + Power buttons, the phone vibrates, displays nothing for 2-3 seconds (not even a black screen, the screen is completely off). After that the "Honor" logo is dispayed for less than a second then the screen "Your device has been unlocked and can't be trusted [...] Your device is booting now..." with no option at all.
The problem is that this screen stays forever and never displays the recovery mode screen. If I entered this mode using the physical buttons, I can just press "Power" for a few seconds and then it reboots the phone normally. But if I used "adb", each reboot makes the phone entering again the same recovery mode that doesn't work, so I use the Volume Up + Power key while the phone is connected via USB to my laptop to enter e-recovery mode, then reboot normally.
Does anyone know how to solve this problem ? I really want to root my phone but I don't know what to do for now.
Thanks by advance for your answers !
ClementNerma said:
Hello everyone,
I bought a few days ago the Honor 5C and decided to root it. So I installed the TWRP (Nemo) using "fastboot", downloaded a ZIP of SuperSU and placed at the root of the internal storage. But when I try to enter recovery mode by using "adb reboot recovery" or by pressing the Volume Up + Power buttons, the phone vibrates, displays nothing for 2-3 seconds (not even a black screen, the screen is completely off). After that the "Honor" logo is dispayed for less than a second then the screen "Your device has been unlocked and can't be trusted [...] Your device is booting now..." with no option at all.
The problem is that this screen stays forever and never displays the recovery mode screen. If I entered this mode using the physical buttons, I can just press "Power" for a few seconds and then it reboots the phone normally. But if I used "adb", each reboot makes the phone entering again the same recovery mode that doesn't work, so I use the Volume Up + Power key while the phone is connected via USB to my laptop to enter e-recovery mode, then reboot normally.
Does anyone know how to solve this problem ? I really want to root my phone but I don't know what to do for now.
Thanks by advance for your answers !
Click to expand...
Click to collapse
Are you on EMUI 5 (Android Nougat) ? If so, official TWRP is not compatible with version > EMUI 4.x for now.
I'm using EMUI 5.0 / Android 7.0.
So now I've installed an incompatible TWRP can I just downgrade to EMUI 4.0 / Android 5.0 then flash it again and root my phone or should I reflash the original recovery before doing that ? I've read somewhere that updating a rooted phone could brick it so even if mine has just a TWRP and want to downgrade instead of upgrading I prefer to be sure.
Thanks by advance !
ClementNerma said:
I'm using EMUI 5.0 / Android 7.0.
So now I've installed an incompatible TWRP can I just downgrade to EMUI 4.0 / Android 5.0 then flash it again and root my phone or should I reflash the original recovery before doing that ? I've read somewhere that updating a rooted phone could brick it so even if mine has just a TWRP and want to downgrade instead of upgrading I prefer to be sure.
Thanks by advance !
Click to expand...
Click to collapse
you need install original recovery and extract update.app from B100 firmware, then you place it to "dload" folder in your sd card and flash using 3 buttons. you cant full brick by messing with root. only soft brick which is fixable.
Ok I'll try it. I will post again if something comes wrong.
Thanks a lot for your help
I forgot to ask about one thing : I'm owning a phone with NEM-L51 model and I don't know if I can use NEM-L22 firmware ? If I can't, where can I find the right files to downgrade this specific model ? All the firmware files I see on the web are for the NEM-L22...
EDIT : I've found the B102 firmware for NEM-L51 model (Europe + UK) can I take it for the downgrade or is the B100 specific version needed ?
ClementNerma said:
Hello everyone,
I bought a few days ago the Honor 5C and decided to root it. So I installed the TWRP (Nemo) using "fastboot", downloaded a ZIP of SuperSU and placed at the root of the internal storage. But when I try to enter recovery mode by using "adb reboot recovery" or by pressing the Volume Up + Power buttons, the phone vibrates, displays nothing for 2-3 seconds (not even a black screen, the screen is completely off). After that the "Honor" logo is dispayed for less than a second then the screen "Your device has been unlocked and can't be trusted [...] Your device is booting now..." with no option at all.
The problem is that this screen stays forever and never displays the recovery mode screen. If I entered this mode using the physical buttons, I can just press "Power" for a few seconds and then it reboots the phone normally. But if I used "adb", each reboot makes the phone entering again the same recovery mode that doesn't work, so I use the Volume Up + Power key while the phone is connected via USB to my laptop to enter e-recovery mode, then reboot normally.
Does anyone know how to solve this problem ? I really want to root my phone but I don't know what to do for now.
Thanks by advance for your answers !
Click to expand...
Click to collapse
It is easy bro . When the phone shows warning logo , click volume up + power and don't leave it untill it find a vibration . Leave the buttons after 3 seconds u felt vibration
gopinaidu77 said:
It is easy bro . When the phone shows warning logo , click volume up + power and don't leave it untill it find a vibration . Leave the buttons after 3 seconds u felt vibration
Click to expand...
Click to collapse
Thanks for your help but this doesn't work. When I do what you say it goes again and again to the same warning screen which never disappears. This is really strange, when I see videos I find on YouTube all Honor 5C owners that just do what you say enter in recovery mode, but it's not my case... I really wonder why.
I don't know if that can help you to understand, but I'm using a french Honor 5C phone, with EMUI 5.0 / Android Nougat like I said previously, model is NEM-L51 and I did the Android Nougat update several days ago using the Honor's official update application, which is natively installed on the phone.
About the firmwares, I've tried the B102 version for the specific model I own but each time (I downloaded the update ZIP several times, the first one with two folders named '1-main' and '2-vendor', the second with just the 'dload' files) the update stops at 5 purcents and says "Software install failed! Incompatibility with current version. Please download the correct update package."
What can I do to solve this problem ?
ClementNerma said:
Thanks for your help but this doesn't work. When I do what you say it goes again and again to the same warning screen which never disappears.
About the firmwares, I've tried the B102 version for the specific model I own but each time (I downloaded the update ZIP several times, the first one with two folders named '1-main' and '2-vendor', the second with just the 'dload' files) the update stops at 5 purcents and says "Software install failed! Incompatibility with current version. Please download the correct update package."
What can I do to solve this problem ?
Click to expand...
Click to collapse
When u click on vol up + power in warning screen .dont leave it till it shows erecovery . Probably its 6-7 seconds
gopinaidu77 said:
When u click on vol up + power in warning screen .dont leave it till it shows erecovery . Probably its 6-7 seconds
Click to expand...
Click to collapse
When you do Volume Up + Power it attemps to enter recovery mode, not recovery (that's what I read), excepted if a USB cable is plugged in (which is not my case). And that still doesn't work.
However, I'm able to enter erecovery mode by turning on the phone with only the Power button, then holding "Volume Up" as written on the screen (there are 3 boot options that shows up, but only when I boot normally) and I enter erecovery mode. But I can't do anything interesting in this mode, just download the latest firmware (which fails at each attempt, even when I'm connected to a working WiFi point), shutdown or reboot the phone normally.
Shoud I show you a video of when I boot my phone in normal mode / recovery mode / erecovery mode ?
ClementNerma said:
When you do Volume Up + Power it attemps to enter recovery mode, not recovery (that's what I read), excepted if a USB cable is plugged in (which is not my case). And that still doesn't work.
However, I'm able to enter erecovery mode by turning on the phone with only the Power button, then holding "Volume Up" as written on the screen (there are 3 boot options that shows up, but only when I boot normally) and I enter erecovery mode. But I can't do anything interesting in this mode, just download the latest firmware (which fails at each attempt, even when I'm connected to a working WiFi point), shutdown or reboot the phone normally.
Shoud I show you a video ?
Click to expand...
Click to collapse
No i understood
gopinaidu77 said:
No i understood
Click to expand...
Click to collapse
The problem is that I can't enter recovery mode, each time I try to install an OTA or full update package from the /dload folder on the SD card it fails, so I can't downgrade at all. Do you know a link that sure points to the good update package version for the Honor 5C on EMUI 5.0 in order to downgrade to Marshmallow ? I've found several links during my searches but I don't know if the installation fails because of a phone's bug or if it fails because of an invalid version.
EDIT : I forgot to precise the long model name of my phone : NEM-L51C432B350. On Firmware Finder Rewrite it shows that there are only two update packages for it, published on 20.04.2017... So I wonder if I need to download the three files shown in the filelist of the big update (1.68 Gb) and install them on the device ?
ClementNerma said:
The problem is that I can't enter recovery mode, each time I try to install an OTA or full update package from the /dload folder on the SD card it fails, so I can't downgrade at all. Do you know a link that sure points to the good update package version for the Honor 5C on EMUI 5.0 in order to downgrade to Marshmallow ? I've found several links during my searches but I don't know if the installation fails because of a phone's bug or if it fails because of an invalid version.
Click to expand...
Click to collapse
Stock recovery wont have an option . There is no graphical UI for installation.
Downgrade or update is just a manual procedure.
In order to roll back , u need to install a roll back package and then the origional MM package . Using the three button combination
gopinaidu77 said:
Stock recovery wont have an option . There is no graphical UI for installation.
Downgrade or update is just a manual procedure.
In order to roll back , u need to install a roll back package and then the origional MM package . Using the three button combination
Click to expand...
Click to collapse
Ok but where can I find this rollback package ? I only find files for the NEM-L22 model...
EDIT : If found the Russian version from here but is it ok to take it ?
ClementNerma said:
Ok but where can I find this rollback package ? I only find files for the NEM-L22 model...
EDIT : If found the Russian version from here but is it ok to take it ?
Click to expand...
Click to collapse
Yes that's fine.
gopinaidu77 said:
Yes that's fine.
Click to expand...
Click to collapse
Ok so in the guide I found on the same page I linked in my previous post (the guide is hopefully written in english) it says that the phone must haven't been rooted or even unlocked, so I prefered to relock the bootloader (and completely reset my phone, for the third time at least in two days).
But then I realized I would need to have an unlocked bootloader for the flash so I unlocked it again, but now the device stucks on "Your device is booting now..." with no option at all whatever I do, whatever the buttons I push... I'll really start to think I'm simply idiot
I'm searching on how to solve this new problem and unbrick the phone... 'cause I can't even shutdown it, the "Volume Up + Power" combination while USB plugged in or anything else doesn't work this time.
EDIT : Okay so my phone seems to really be hard-bricked. My phone just stays at the screen "Your device is booting now..." with no option at all, I can't shutdown it, I can't enter recovery or erecovery mode. Does anyone know what to do or is my phone definitively bricked ?
ClementNerma said:
Ok so in the guide I found on the same page I linked in my previous post (the guide is hopefully written in english) it says that the phone must haven't been rooted or even unlocked, so I prefered to relock the bootloader (and completely reset my phone, for the third time at least in two days).
But then I realized I would need to have an unlocked bootloader for the flash so I unlocked it again, but now the device stucks on "Your device is booting now..." with no option at all whatever I do, whatever the buttons I push... I'll really start to think I'm simply idiot
I'm searching on how to solve this new problem and unbrick the phone... 'cause I can't even shutdown it, the "Volume Up + Power" combination while USB plugged in or anything else doesn't work this time.
EDIT : Okay so my phone seems to really be hard-bricked. My phone just stays at the screen "Your device is booting now..." with no option at all, I can't shutdown it, I can't enter recovery or erecovery mode. Does anyone know what to do or is my phone definitively bricked ?
Click to expand...
Click to collapse
Long click of power button will shut down the phone. Why u always refer about usb cable . Follow all instructions unplugged
Even the same happend for my honor 8 . Ur device isnt hard bricked .its just a soft brick
gopinaidu77 said:
Long click of power button will shut down the phone.
Even the same happend for my honor 8 . Ur device isnt hard bricked .its just a soft brick
Click to expand...
Click to collapse
Nope, long click of power button will just reboot the phone and make it displaying the same screen again and again.... I can't shutdown it at all. I've tried several times but it doesn't work :crying:
ClementNerma said:
Nope, long click of power button will hust reboot the phone and make it displaying the same screen again and again.... I can't shutdown it at all. I've tried several times but it doesn't work :crying:
Click to expand...
Click to collapse
Yes , the same happend for me ! U can unbrick bro
gopinaidu77 said:
Yes , the same happend for me ! U can unbrick bro
Click to expand...
Click to collapse
But how can I unbrick the phone ? I can't enter in any mode, I can't connect it to PC, I can't shutdown the phone, I can't use ADB or FastBoot on it, I can't reflash the bootloader or install a TWRP, downgrade or boot normally, I can't do anything !
So how could I unbrick it ? For now it's just still displaying "Your device is booting now..."
If you know how to do, please tell me so I can unbrick my phone. Sorry for asking you so many things I don't understand myself why there are so many problems...
Hello, I have issues updating via wireless update. When I try to update through it I get an error telling me my system was damaged. From what I've looked up this happens when you've rooted your phone. Which is odd to me since I just got this phone. I am completely new to android so doing all this kind of stuff is beyond me at the moment. I was able to boot into I think recovery mode using the power button and volume up button. Doing that I attempted to install through that. When I attempted to do so I just get a Error. Nothing specific other than that. I do not have a SIM or external SD card installed. Everything is brand new and not used. Help would be nice.
Sylanna said:
Hello, I have issues updating via wireless update. When I try to update through it I get an error telling me my system was damaged. From what I've looked up this happens when you've rooted your phone. Which is odd to me since I just got this phone. I am completely new to android so doing all this kind of stuff is beyond me at the moment. I was able to boot into I think recovery mode using the power button and volume up button. Doing that I attempted to install through that. When I attempted to do so I just get a Error. Nothing specific other than that. I do not have a SIM or external SD card installed. Everything is brand new and not used. Help would be nice.
Click to expand...
Click to collapse
Go back into recovery mode (hold down the volume up and power button simultaneously until the recovery menu comes up). Select factory reset (this will wipe everything and restore it back to factory settings). You should be able to update after that
Hi Everyone! Well, today is my time to ask for some help! :fingers-crossed:
I got my hands on a great looking Huawei P20 PRO, unfortunately the Phone is locked FRP... But as i had searched around, there was a method to bypass that by a simple bug they had on the "TALKBACK", like one week ago people was doing that bypass successfully , but this phone has a newer version of talk back, 7.1.x.x...
On the videos people have the previous 6.1.x.x version... That means i don't have the same "help" option as they have.
-After that i tried to get the phone into Fastboot mode, but i can't get the phone on that mode, i press volume down and hold for a while with the device turned off, then i plug the usb, and it just starts charging...
-I press Both vol up and vol down buttons with power at same time, it goes to a screen "EMUI" that says "SOFTWARE INSTALL FAILED! GET HELP FROM xxxx.EMUI COM/BLABLABLA) and says "Reboot system now"...i then press reboot now, and i does a regular reboot and starts up to select language etc, all good... BUT FRP locked...
- Then last night i tried to press VOLUME UP then plug the USB and it got into Erecovery mode, that gave me the option to download the latest version, wipe the current one, shutdown, or reboot... well i had nothing to lose and i did the first to download the latest version, after a 4gb download and install the phone is on the same situation, same version, same everything....
Makes me wonder if someone already done bad attempts before me.
Is there anyway to get the phone on Flashboot? Or bypass the FRP ?
Same
I have exactly the same
Any help????
Thebuckers1986 said:
I have exactly the same
Any help????
Click to expand...
Click to collapse
have you tried the wifi update? it didnt work with me... search for "Upgrade to Android Pie through eRecovery and the Wifi - Firmware Finder PC"
Hi guys. I'm a stock OxygenOS ROM user and No Root either. I having trouble with recent system update. Every time I update, the phone reboots into screen like below, after chosing language, I get an error message "system error, after select language please select Online update (keep data) to reovery system". After pressing OK, there's no such online update option. But only choices as follow: 1) Format Data 2) Reboot 3) Power off 4) Fast Boot 5) Recovery mode. Chosing reboot, power off, recovery always get the phone to reboot into this same screen. When chose fastboot, then press power off button. Phone boots into usable state again after long wait, and I get an Update Failure message. I just want to update my stock phone, preferably without dangerous method like rom flashing. Is this a bug and I should wait for next update till it's fixed? Much appreciate for advices and help.
OnePlus Nord CE 5G
Same issue for me. Phone is now having issues, so not very happy with OnePlus!!!