Database Develop

[Q] SGS Stuck in the boot-loop

This is my first post, so I will try to be clear:
I have SGS I9000 2.3.3 rooted with Odin (CF-Root-XW_NEE_JVH-v3.2-CWM3RFS) and was working perfectly for the last weeks.
Today I tried to setup my work email on my phone with the built-in Email Client, and due to company policy I had to encrypt all the files on the phone( this is done automatically).
The issue started after it finished encrypting the files, the mobile didn't start again and got stuck at the logo page. I tried many times without success I also tried to go to the recovery mode but it's also stuck at Downloading page and it doesn't move (No menu).
how can I perform a factory reset? Is there any other solution
Thanks for ur answers

Your best off reflashing the firmware dude, via Odin
Sent from my CM7 modded I9000. Kernel is one mean son of a Glitch!

thanks for your recommendation.
I just tried to reflash it with the official load from Samsung and it failed, below the output of odin:
<ID:0/006> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> PDA_XWJVH_Sbl.tar.md5 is valid.
<OSM> PDA_XWJVH_Sbl.tar.md5 is valid.
<OSM> CSC_XEE_JV3.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/006> Odin v.3 engine (ID:6)..
<ID:0/006> File analysis..
<ID:0/006> SetupConnection..
<ID:0/006> Initialzation..
<ID:0/006> Set PIT file..
<ID:0/006> DO NOT TURN OFF TARGET!!
<ID:0/006> Get PIT for mapping..
<ID:0/006> Firmware update start..
<ID:0/006> param.lfs
<ID:0/006> zImage
<ID:0/006> boot.bin
<ID:0/006> Sbl.bin
<ID:0/006> factoryfs.rfs
<ID:0/006> dbdata.rfs
<ID:0/006> param.lfs
<ID:0/006> Transmission Complete..
<ID:0/006> Now Writing.. Please wait about 2 minutes
<ID:0/006> Receive Response form LOKE
<ID:0/006> zImage
<ID:0/006> Transmission Complete..
<ID:0/006> Now Writing.. Please wait about 2 minutes
<ID:0/006> Receive Response form LOKE
<ID:0/006> boot.bin
<ID:0/006> Transmission Complete..
<ID:0/006> Now Writing.. Please wait about 2 minutes
<ID:0/006> Receive Response form LOKE
<ID:0/006> Sbl.bin
<ID:0/006> Transmission Complete..
<ID:0/006> Now Writing.. Please wait about 2 minutes
<ID:0/006> Receive Response form LOKE
<ID:0/006> factoryfs.rfs
<ID:0/006> Transmission Complete..
<ID:0/006> Now Writing.. Please wait about 2 minutes
<ID:0/006>
<ID:0/006> Receive Response form LOKE
<ID:0/006> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)

where did you download the files? try download the ones from Ramad thread

I downloaded the files from thd "forum Official firmwares for Samsung Galaxy S I9000 - Download" which comes from xda-developers
It works now , by using Odin v1.7 instead of v1.82 with the same 4 files

[Q] Bricked Note 3 N9005!!! Please help

Hi all,
I wanted to flash a custom ROM onto my new note 3. the first time I flashed it using ODIN it finished and passed but would not boot up. now when I try flashing it fails every-time with the below!
I live in the UK and bought the phone from carfone warehouse its on Vodafone so I have downloaded the Vodafone ROM from sam mobile.
I really need some help with this and its driving me crazy! I've been working on this for 8 hours now and just can't get it to work. it seemed to happen and stop passing via ODIN when I did a repartition by mistake
Any help would be greatly appreciated.:good:
<ID:0/003> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> N9005XXUDMJ6_N9005VFGDMJ1_N9005XXUDMJ4_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> sbl1.mbn
<ID:0/003> NAND Write Start!!
<ID:0/003> aboot.mbn
<ID:0/003> rpm.mbn
<ID:0/003> tz.mbn
<ID:0/003> sdi.mbn
<ID:0/003> NON-HLOS.bin
<ID:0/003> boot.img
<ID:0/003> recovery.img
<ID:0/003> system.img.ext4
<ID:0/003> modem.bin
<ID:0/003> cache.img.ext4
<ID:0/003> hidden.img.ext4
<ID:0/003> FAIL! (Ext4)
<OSM> All threads completed. (succeed 0 / failed 1)
<ID:0/003> Removed!!

GT-I9305 Bootloop? Odin Fail, wanting data back...

Hi all,
Samsung Galaxy S3 - GT-I9305. After the OS patch was getting a few issues like system randomly resting, security block popups on some apps when there never was before. One night however woke up and the phone was powered down. Now only powers up only into Samsung Logo bootloop. Cant enter recovery mode, just goes into the loop. I've got 2 ROMs from SAM mobile for my carrier, one older and one recent, as i'm unsure what my ROM is and cant check it now. Both however fail with Odin. Log listing below.
Have tried different ports, using original cable. Ideally would like to get my data back as pictures and contacts were not backed up.... Please help! Pretty desperate and haven't really found anything in forums for this situation.
Odin logs;
<ID:0/006> Added!!
<OSM> Enter CS for MD5..
<OSM> Binary Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/006> Odin engine v(ID:3.1100)..
<ID:0/006> File analysis..
<ID:0/006> SetupConnection..
<ID:0/006> Initialzation..
<ID:0/006> Get PIT for mapping..
<ID:0/006> Firmware update start..
<ID:0/006> SingleDownload.
<ID:0/006> sboot.bin
<ID:0/006> NAND Write Start!!
<ID:0/006> FAIL!
<ID:0/006>
<ID:0/006> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)

TWRP
Hello and thank you for using Q/A,
can you please try flashing TWRP via AP:
twrp-2.8.7.0-i9305.img.tar
And then please try to boot into TWRP using the known combination. Tell me, if your I9305 is booting into TWRP then.
Regards
Trafalgar Square

Thanks for reply. I tried on Odin3 1.87 and 3.10.7 both fail; log
<ID:0/006> Added!!
<ID:0/006> Odin engine v(ID:3.1100)..
<ID:0/006> File analysis..
<ID:0/006> SetupConnection..
<ID:0/006> Initialzation..
<ID:0/006> Get PIT for mapping..
<ID:0/006> Firmware update start..
<ID:0/006> SingleDownload.
<ID:0/006> recovery.img
<ID:0/006> NAND Write Start!!
<ID:0/006> FAIL!
<ID:0/006>
<ID:0/006> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
Option selected auto reboot via AP.
:crying:
Any other suggestions?

The thread is dead, but in case anyone is coming across the same sort of problem.. i bit the bullet and took it to a service tech. They couldn't fix it and had to replace the motherboard. So unfortunately that was the solution for me anyway. :crying:

[SOLVED] N-910T Unable to flash stock rom (N910TUVU2DOK2)

I tried rooting a Note 4 (N910T that came with 5.1.1) following the easy steps pinned in the general section. I was able to install the recovery but Something failed after the CF root script. Because I got stuck in a boot loop. I then wiped the cache partition and tried rebooting. The same issue persists. So I downloaded the stock firmware (N910TUVU2DOK2_N910TTMB2DOK2_TMB) and tried flashing that in Odin 3.10.7. During the process I received.
<ID:0/003> Odin engine v(ID:3.1100)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> SingleDownload.
<ID:0/003> recovery.img
<ID:0/003> NAND Write Start!!
<ID:0/003> RQT_CLOSE !!
<ID:0/003> RES OK !!
<ID:0/003> Removed!!
<ID:0/003> Remain Port .... 0
<OSM> All threads completed. (succeed 1 / failed 0)
<OSM> Enter CS for MD5..
<OSM> Binary Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Added!!
<ID:0/003> Odin engine v(ID:3.1100)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> SingleDownload.
<ID:0/003> aboot.mbn
<ID:0/003> NAND Write Start!!
<ID:0/003> sbl1.mbn
<ID:0/003> rpm.mbn
<ID:0/003> tz.mbn
<ID:0/003> sdi.mbn
<ID:0/003> NON-HLOS.bin
<ID:0/003> boot.img
<ID:0/003> recovery.img
<ID:0/003> system.img.ext4
<ID:0/003> __XmitData_Write
<ID:0/003> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
Click to expand...
Click to collapse
After that, I'm no longer able to boot into TWRP recovery. I get a message about a failed firmware update nor does the OS boot up.
I can still boot into download mode. And I'm able to flash TWRP from ODIN. Although after booting into TWRP and trying to do a wipe. It complains that' it's unable to mount the /system partition.
Could Someone give me a quick hand? I work in IT and I know how to google. So there shouldn't be much hand holding. Thanks in advance.

It was the damn cable. Either the cable or the usb port. I switched both at the same time. The cable I was using was an "OEM" from amazon. That I used to back up the device and flash the recovery. But for some reason it would fail at the step above.
After I swapped to my real OEM usb cable, I was able to flash the rom I was able to.
Not sure I want to try the root again. Anyone have solid instructions on rooting 5.1.1 on the N910T?

SM-T713 to stock rom older android version 6.0 FAILURE

im trying to get back to adnroid 6.0 but after odin progress bar is about to complete i get failed, message, i have used smart switch and can easily flash to newest version of android but i don''t want 7.0 i need 6.0 so i can run the tablet as android 6.0 , need help thanks
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Added!!
<ID:0/003> Odin engine v(ID:3.1207)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> NAND Write Start!!
<ID:0/003> SingleDownload.
<ID:0/003> boot.img
<ID:0/003> recovery.img
<ID:0/003> system.img.ext4
<ID:0/003> cache.img.ext4
<ID:0/003> hidden.img.ext4
<ID:0/003> modem.bin
<ID:0/003> adspso.bin
<ID:0/003> aboot.mbn
<ID:0/003> sbl1.mbn
<ID:0/003> FAIL! (Auth)
<ID:0/003>
<ID:0/003> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)

xiexieni778 said:
im trying to get back to adnroid 6.0 but after odin progress bar is about to complete i get failed, message, i have used smart switch and can easily flash to newest version of android but i don''t want 7.0 i need 6.0 so i can run the tablet as android 6.0 , need help thanks
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Added!!
<ID:0/003> Odin engine v(ID:3.1207)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> NAND Write Start!!
<ID:0/003> SingleDownload.
<ID:0/003> boot.img
<ID:0/003> recovery.img
<ID:0/003> system.img.ext4
<ID:0/003> cache.img.ext4
<ID:0/003> hidden.img.ext4
<ID:0/003> modem.bin
<ID:0/003> adspso.bin
<ID:0/003> aboot.mbn
<ID:0/003> sbl1.mbn
<ID:0/003> FAIL! (Auth)
<ID:0/003>
<ID:0/003> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
Click to expand...
Click to collapse
You need to flash latest 6 rom for your region to succeed , more information would be more useful such as what's your region , did you officially upgraded to 7 using ota update or manually

messi2050 said:
You need to flash latest 6 rom for your region to succeed , more information would be more useful such as what's your region , did you officially upgraded to 7 using ota update or manually
Click to expand...
Click to collapse
got this finally to work, damn there was a flaw in the file i download sammobile , since i cant resume downloads sometimes the file just ends a little earlier