Has anyone replaced the battery on their note5 yet? - Galaxy Note5 Q&A, Help & Troubleshooting

I'm not satisfied with the performance of my battery. I tried everything from greenify to factory reset. I think its time to replace the battery of my note5. Has anyone replaced their battery? What was the cost? And how should i make sure I am getting the original battery from the service center. I am in india so if anyone has replaced the bettery of s6, note5, s7 etc please let me know

I replaced my n5's battery in RMA service. No cost

I've replaced my note 5 battery a couple times... not too hard. You will may or may not crack the back glass when pulling it off of device... ymmv.
You basically just take a blow dryer, heat he back, peal glass back off, unscrew like 15 little screws, push phone guts and screen out of metal outer shell, remove old battery and ribbon connector (old battery may be glued in), replace battery, put guts and screen back in metal shell, replaces screw, put back glass back on.
All said in done, back glass cost me $10, and battery was about the same, so $20 in total to swap. I've done a couple times now, can prob do it in under 5 minutes. First time took me almost 30... godspeed

Sampson0420 said:
I've replaced my note 5 battery a couple times... not too hard. You will may or may not crack the back glass when pulling it off of device... ymmv.
You basically just take a blow dryer, heat he back, peal glass back off, unscrew like 15 little screws, push phone guts and screen out of metal outer shell, remove old battery and ribbon connector (old battery may be glued in), replace battery, put guts and screen back in metal shell, replaces screw, put back glass back on.
All said in done, back glass cost me $10, and battery was about the same, so $20 in total to swap. I've done a couple times now, can prob do it in under 5 minutes. First time took me almost 30... godspeed
Click to expand...
Click to collapse
cool, i am into electronics and i have all the tools to do it, just wanted to know if it is worth doing ourselves or going to the official service center. how is the after market battery performing? is it supporting the quick charge?

Related

Water Damage Repair Help Nexus 6

Hello everyone
So a couple weeks ago I took a unexpected swim with my Nexus 6 in my pocket, and haven't gotten it to work since. When I got out I immediately took the phone out of my pocket and turned it off, only to have it boot back into fastboot a few seconds later, turn off, boot to fastboot, and turn of again. It did this several times till it just stayed off. I took it apart, dried it, and cleaned it in Isopropyl alcohol and tried to turn it on but got no response no matter what I did. :crying:
I would consider it fried except whenever I plug it into my charger, the charging icon comes up like normal and even does the battery filling up animation. I replaced the power/volume button strip inside the phone hoping that it was the only problem, but it still would't turn on. I haven't replaced the battery yet because the charging animation shows it's holding charge, but loosing 40ish% after a week and a half of sitting there.
So is there something else I can do, or is it fried? I'm probably going to get a new battery to see if that improves anything, but I honestly don't know what more to do. If anyone has any ideas, I'd love to hear them.
Thanks in advance!
It's fried. Best you can do is send to shop and see if they can salvage it.
Alright, I'll guess I'll have to do that. Thank you for your reply.
I would like to share photos of my phone and seee if anyone vcan help, my situation is kind of similar. I tried to charge after to days of silica drying and cleaning with IPA.
I thin the connection around the battery area isn't secure. Is there a glue that i could buy?
The only thing a shop may do, is give it a bath in a ultrasonic machine, and bake the board. Try a new battery, internal batteries never do well in WD.
oOflyeyesOo said:
The only thing a shop may do, is give it a bath in a ultrasonic machine, and bake the board. Try a new battery, internal batteries never do well in WD.
Click to expand...
Click to collapse
How about sticking the charging coil to the new battery? What type of adhesive is needed?
uncle_buckman said:
How about sticking the charging coil to the new battery? What type of adhesive is needed?
Click to expand...
Click to collapse
You may still have enough adhesive left over on the coil to stick it to it. Otherwise it doesn't matter much, as long as its connected and not crazy loose, the frame will hold it in place.
oOflyeyesOo said:
You may still have enough adhesive left over on the coil to stick it to it. Otherwise it doesn't matter much, as long as its connected and not crazy loose, the frame will hold it in place.
Click to expand...
Click to collapse
I got it kind of working, but the sound is fuzzy and the screen is flickering a little.
I'm missing some screws, so I'll need to buy some new ones.
T3/M3 torx screws, 2mm/3mm height/diameter?

Great, cracked the screen of my Z3 Compact

This morning I was cleaning my phone (getting rid of the finger prints/smudges) while standing up when it slipped out of my hand and hit the tiled floor. Everything is fine except the screen (which is cracked). Screen works fine but is unresponsive no matter where I press or touch the screen. How much does a Z3 Compact replacement screen cost? I searched around and it seems it is about $100?
Screen replacement costs in Poland +/- 135$
(authorised sony service)
Yes' it's hard to get original one cheaper than 100-120$. You can search for some Chinese replacement cause sometimes it looks quite similar to original one but You must check it before buying. Last time I had a client with Z1c replacement screen which he bought for 40$ and there was no white color, everything what should be white was purple.
Voids warranty, cheap replacement
Got mine from here replacebase dot co dot uk (can not post links ), of course you void your warranty if you do it yourself.
Parts are good quality till now. I advice to order a back glass too, I broke mine when taking it out and had to reorder again (costs approx 6 pound).
Next time just heat up back glass with hair dryer and You wont break it.
Chamelleon said:
Next time just heat up back glass with hair dryer and You wont break it.
Click to expand...
Click to collapse
Thanks for the input
The problem was a small crack which did not matter until you have to remove it, you can not pull on it when its cracked. Anyway I will use a hair dryer to put it back together (assemble, heat up, press with books).
Thanks for the replies.
I'll be getting the repair done from the official Sony shop/distributor I bought the phone from. Just wanted to get an idea of how much it "should" cost before I approach them.
m4mbax said:
Thanks for the input
The problem was a small crack which did not matter until you have to remove it, you can not pull on it when its cracked. Anyway I will use a hair dryer to put it back together (assemble, heat up, press with books).
Click to expand...
Click to collapse
Hello
I have tried to change my backglass 3 times but after a few hours the glass falls off... (Yes, I cleaned the phone removing all the old adhesive - and yes, I had pressure on it over night ) But all the instructions I have found on the internet never mentioned anything about putting the glass on, and HEATING it up, and the putting pressure on it... Where have you found that advice? You could imagine that heating up would ruin the adhesive/making it thinner and thereby not waterproof...? But on the other hand your succesrate probably beats mine...
Foxhunter123 said:
Hello
I have tried to change my backglass 3 times but after a few hours the glass falls off... (Yes, I cleaned the phone removing all the old adhesive - and yes, I had pressure on it over night ) But all the instructions I have found on the internet never mentioned anything about putting the glass on, and HEATING it up, and the putting pressure on it... Where have you found that advice? You could imagine that heating up would ruin the adhesive/making it thinner and thereby not waterproof...? But on the other hand your succesrate probably beats mine...
Click to expand...
Click to collapse
I think it was a comment below the iFixit tutorial. But one big warning here, I did extra maximally stupid and put it to 'press' under my table (with books around it). The table was too heavy and cracked my front screen once again :crying:
+ The rear glass sits fixed and has not loosened.
- Don't put too much pressure or you destroy it yet again like stupid me
m4mbax said:
I think it was a comment below the iFixit tutorial. But one big warning here, I did extra maximally stupid and put it to 'press' under my table (with books around it). The table was too heavy and cracked my front screen once again :crying:
+ The rear glass sits fixed and has not loosened.
- Don't put too much pressure or you destroy it yet again like stupid me
Click to expand...
Click to collapse
Doh!!! ? I have also read on Ifixit and can see there are different opinions about if it is nessesary to heat or not. But I think I will follow your advice and heat the new back before putting it under (less pressure) ?.
Another thing I read on Ifixit is that someone writes that you should put on an adhesive sticker - eventhough the new back comes with adhesive already on...? What is your advice on this?
Most pre-glued adhesive stickers on back are useless. Now everytime I change back in Xperia Z, Z1, Z2, Z3 and compacts I need to remove pre-glued sticker and change it to original one. Many times I had complaint on it from my clients saying that back glass came off. So it's better to order original back glass or just original adhesive.
Foxhunter123 said:
Doh!!! I have also read on Ifixit and can see there are different opinions about if it is nessesary to heat or not. But I think I will follow your advice and heat the new back before putting it under (less pressure) .
Another thing I read on Ifixit is that someone writes that you should put on an adhesive sticker - eventhough the new back comes with adhesive already on...? What is your advice on this?
Click to expand...
Click to collapse
Good
Mine came with the adhesive ON the screen, I used that one, I didn't have a separate one. Be extra careful when 'placing' the adhesive where it belongs because you can not remove it once place (okay maybe slightly). Its important that it fits on the first to first and a half try. More adhesive means thicker layer --> glass will stick out
Anyway, most of the stories you read online are partially BS, the phone will work even when the glass is a tiny bit loose or when the adhesive rotated and is a bit thicker in one place. In my eyes, when you dared to order, you are very much capable of assemble the parts.
In btw, ordered new glasses today, hope my two left hands fix it this time.
PS: A lesson I learned on a friends Galaxy S2, do NEVER EVER try to use force when something sticks or is not as loose as in a video. Google or ask another person maybe you just dont do the trick. A connector didnt want to come off so we used a lever to lift it, CLICK, the place where the lever levered broke the board... :silly:
Edit 1: I think its not necessary to HEAT it, it just has to be a lil bit warmer than in your pocket or when calculating heavily. 30s under a hairdryer will be more than enough i guess.
Forgot to update this thread. I received my fixed phone last week. They replaced the screen and even the "bumpers" around the phone for $98. They even delivered the phone to my home free of charge. Looks brand new, all the minor dings I had on the phone are gone.
On another note, I also bought my first iPhone. Got an Space Gray iPhone 6s 128 GB with the official/Apple leather case for the 6s. Got it last Thursday. Been playing around with it a lot and, overall, I love it. Deciding on whether to keep my Z3 Compact as a back-up phone or just sell it. But geez, does the iPhone 6s load games and other apps fast (thanks to its NVMe storage).

Battery reuse with screen + frame replacement?

So, my girlfriend dropped her S7 edge a couple times, and the screen is pretty ****ed up, although perfectly usable. the first drop has broken only the glass, but the last one broke a small part of the display as well, so I thought I could look up replacement procedures. It turns out that they seem to be pretty hard, of course. then i've noticed that they sell the screen with and without the frame, so I can gather that the main advantages of buying a framed one are: it could make the repair process a little simpler because i don't need to take the extra steps of removing the old screen and replacing it, and I wouldn't have to worry about a bent chassi screwing the new display - all that for like 15 bucks more or something.
but according to the ifixit site there's no way to reuse the original battery on the new chassi because the heat applied to the battery to remove it also ****s it up - except that in their own battery replacement walkthrough they also talk about a heat-less method of removing the battery by applying isopropilic alcohol to the edges of the battery to unglue it from place.
so I guess my question is: could I reuse a battery removed by the heatless method on a new chassi?
khaotik said:
So, my girlfriend dropped her S7 edge a couple times, and the screen is pretty ****ed up, although perfectly usable. the first drop has broken only the glass, but the last one broke a small part of the display as well, so I thought I could look up replacement procedures. It turns out that they seem to be pretty hard, of course. then i've noticed that they sell the screen with and without the frame, so I can gather that the main advantages of buying a framed one are: it could make the repair process a little simpler because i don't need to take the extra steps of removing the old screen and replacing it, and I wouldn't have to worry about a bent chassi screwing the new display - all that for like 15 bucks more or something.
but according to the ifixit site there's no way to reuse the original battery on the new chassi because the heat applied to the battery to remove it also ****s it up - except that in their own battery replacement walkthrough they also talk about a heat-less method of removing the battery by applying isopropilic alcohol to the edges of the battery to unglue it from place.
so I guess my question is: could I reuse a battery removed by the heatless method on a new chassi?
Click to expand...
Click to collapse
check your battery recharge cycle with samsung info app if it's more than 300 it is better for you to change it to have a better battery life. If it is healty one you can use it. Every service point they use the old one and all remove it with heat.

Moto G6 lterally coming apart at the seam

Hi, I have an almost 2 year old Moto G6 (just the G6, not Play or Plus). Had it in the same case that length of time. About a month ago, found it was hard to press the power button. I finally just took it out of the case, and in doing so, found the allegedly permanently sealed back cover was coming loose on the side with the power button as well as the bottom where the USB-C jack is. Looks like the adhesive is stretchy but no longer very tacky, and trying to manually press the back cover into place is futile as it won't stay and won't even go all the way in. The phone still works, and after removing it from the case, I now see the power button is fine. I assume it's out of warranty now, I think 1 year and I have no add-on protection plan on my T-Mobile bill. I seen videos of people removing the back cover with a heat gun and razor blade to replace the battery. On what I can see, doesn't look like my battery is bulging. Tempted to crazy glue where the cover is separating, but I doubt that would hold with the pressure that makes the cover pull out again once pushed down. I would think at this point I could carefully just manually remove the whole back cover by hand.My dexterity is awful on repairing small delicate things. Can a shop repair this fairly cheaply? Any advice? I'm in Ohio/USA. Thanks!
I took mine out of the case tonight to clean it and discovered I have exactly the same problem! My case is such that if I put the phone back in it, the case "snaps" together and hence keeps the phone together. Mine is probably two years old too, so I'm sure no fix is possible (but I'll keep my eye on this thread). I'll leave the case on and begin looking for a new phone.
I'm with Sprint so I'm anticipating the conversion to TMo, so I'd rather wait until that happens before I buy a new one.
dannykewl said:
Hi, I have an almost 2 year old Moto G6 (just the G6, not Play or Plus). Had it in the same case that length of time. About a month ago, found it was hard to press the power button. I finally just took it out of the case, and in doing so, found the allegedly permanently sealed back cover was coming loose on the side with the power button as well as the bottom where the USB-C jack is. Looks like the adhesive is stretchy but no longer very tacky, and trying to manually press the back cover into place is futile as it won't stay and won't even go all the way in. The phone still works, and after removing it from the case, I now see the power button is fine. I assume it's out of warranty now, I think 1 year and I have no add-on protection plan on my T-Mobile bill. I seen videos of people removing the back cover with a heat gun and razor blade to replace the battery. On what I can see, doesn't look like my battery is bulging. Tempted to crazy glue where the cover is separating, but I doubt that would hold with the pressure that makes the cover pull out again once pushed down. I would think at this point I could carefully just manually remove the whole back cover by hand.My dexterity is awful on repairing small delicate things. Can a shop repair this fairly cheaply? Any advice? I'm in Ohio/USA. Thanks!
Click to expand...
Click to collapse
You could try using a hair dryer to heat up the glue to make it stick together again.
You could try using a hair dryer to heat up the glue to make it stick together again.
Click to expand...
Click to collapse
I thought maybe excessive heat and sweat from being in my pocket on hot days loosened it up.
Thanks for the replies FrogFan and Ragarianok. Sorry for the long delay. In the meantime, I got the back case half off, and indeed a swollen battery. I am going to order a new battery for $4 from Mobile Defenders in MI, battery image says Motorola on it, and they say authorized OEM. A nearby repair shop said they will put it in for $20. They said a decent battery should run $20+, but all those higher priced ones on ebay and Amazon are no-names.
Thanks for coming back, dannykewl. I wasted some time inquiring about a fix from Motorola and found out that their "fix" would cost more than the phone was worth. A local shop quoted a ridiculously high price to fix it, too, but they did say the problem could be caused by a swollen battery. I will check with other local shops to see what they'd charge to replace the battery and seal it back up.
Did you get yours fixed?
POP!
My phone separated today and it is a swollen battery. I suspected for about 2 months the battery was swelling because of pressure points showing up on the screen as bright circles. I was just going to buy a new phone as this was a cheap phone and 2 years old, but the battery did the hard work for me by separating the phone from it's back, so I decided to fix. I removed the battery, ordered replacement battery on ebay and will put back together myself for $12. The $4 batteries are out of stock. The phone has enough stickiness left to hold the backplate and phone together on it's own, and it'll be in the phone case so no worries. Might apply a little Elmers to the surround. From what I read online, and saw on Youtube, be careful with the back, it's actually a glass metal hybrid and not safety glass at that. It will shatter off the metal and into little tiny razors and knives. The screen artifacts disappeared when the back was removed, relieving pressure on the components mashing up against the screen from the inside.. No permanent damage. This new battery should tide me over long enough for the affordable 5g phones to come out. I don't buy pricey phones. Oh, fyi... this is a SUPER easy repair. Have faith and go for it.
I took mine to a local repair shop today and confirmed my problem was also a swelling battery. They will replace the battery for me for $75.
Oh, fyi... this is a SUPER easy repair. Have faith and go for it.
Click to expand...
Click to collapse
I checked out a YouTube video on this topic and quickly confirmed that this repair is way over my head. I don't have the tools or the patience to change the battery in this phone.

Battery replacement. Anyone has done it?

I'm unhappy with my battery life. While it did work 2-3 days with 4-5h SoT at best before I now get around 25-35% in the evening. Not suitable for another day.
So either the battery is done for or the software has become way way worse.
https://www.witrigs.com/oem-battery-replacement-with-frame-for-sony-xperia-xz2
Battery Replacement does seem possible. So has anyone done it? Did it help?
Yes. I have done a complete screen replacement as well as the battery. I didn't need to watch out for a screen as it were completely destroyed. Yup, you're right about the battery, probably it needs to be replaced. I have a neat trick to help you with screen removal. Take a plastic bottle, cut a small rectangle from it (around 4x6cm should be enough) and then round those sharp corners with some scissors so there won't be any sharp edges left. Once you've that done, take your freshly cut plastic card and insert it into bottom gap (where speaker is). You could use a suction cup to raise the glass a little bit. And slice the adhesive around the screen. Ofc be careful not to push it too far to not damage screen ribbon. Watching teardown videos is crucial as you don't wanna pierce or rip apart the screen ribbon. if you want more information about this, feel free to ask As putting everything together - I recommend buying original lcd adhesive for xz2, it's simple and the screen stays on as well as original.
*#*#7378423#*#* go into this service menu then the battery health test, it tells you current max. capacity and health status whether if you need to replace or not.
battery replacement should be relatively easy since it is held down by screws not adhesive, be careful when opening up the phone you may damage the LCD also make sure you clean all the left adhesive residue before applying the new sticker or B7000 glue to the frame
I don't trust those numbers. That's the Problem here...
@Verity.
Did you realize any difference in Battery life before and after the change?
Certainly. I bought used battery as it was cheap and as the old one was quite worrying on the outside. I immediately noticed the difference (especially in sot) so with the new battery you should feel the difference even more.
Not sure if the degradation of the battery is good or bad...
After fully charging now:
And one of the earliest from 2018
https://forum.xda-developers.com/showpost.php?p=83337497&postcount=6
That's pretty normal. Every battery has a lifespan. It's depended on temperature, usage but the most important factor is the charging cycles. After x cycles battery loses it's capacity. It's due to chemical reactions inside of it and there's nothing you could do about it. Until solid state batteries will come out, you will have to change the battery once 2-3 years.
So yeah....
I've done it and i'm not happy
Haldi's Benchmark Thread for Testing&Fiddling with the Xperia XZ2
Howdy, You might remember me from the Xperia Z2 or the Xperia Z. I've started playing around with Android on my old Sony Xperia X10i and i've always liked fiddling around with too much data and thoroughly testing what i own in order to fully...
forum.xda-developers.com

Categories

Resources