I brick my lg f160k while flashing wrong kdz on it. It was in no download no recovery mode. Pc was showing qhsusb_dloade 9008. I searched alot over the internet to unbrick it but found nothing except a thread on veitnam site by a veitnamis developer. Thanks to him for this useful thread. With the help of this i unbrick my cell. It was very difficult to understand the thread while in Vietnam's language but i managed to do so with the help of google translator. I thought i should must share it on xda to English community for easy umderstading. Hit thanks if you get your phone back. And many thanks to veitnamis developer too....
1. Download the qualcom drivers and install it from given link.
https://app.box.com/s/5n42md550n4oxne04xttfz788cp0i4i3
Open device manager and ensure that you have correctly installed qualcom 9008 drivers. Remember the com port
2. Download and unzip this folder
https://app.box.com/s/zvvj2v87csuwmv93k7ztzevuiytyd0fi
You shall have a tool Boar Diag v3.99c folder and two folder named S and L.
3.IMPORTANT. You will have to choose folder S For F160K and S and for F160L and LV choose Folder L.
4. Now run the tool.
Check the 2 points on tool
1.Ap check
2.Emmc Test
In Ap chipset choose board
For F160s and F160k
D1L(MSM8960 SKDA)
FOR 160L
D1L(MSM8960 LV)
Select Com Port shown in device manager of your computer.
In TARGET DIR Choose the Folder of Named S or L according to your modal, As i told you earlier in step 3
Rest all should be unchecked
PRESS START
https://app.box.com/s/hr8y0cmzcond0jciemprl5jzr4rllggn
Now test will start and will take 10 seconds to complete
If this test run successfully AP and EMMC should show pass on tool window
5. In this step Now only uncheck
Emmc Test and then check the
Boot Image Restore and select ABOOT from drop down menu.
Only w points Checked.
Ap Check
Boot Img Restor
Rest all should be uncheck the same as in previous step.
PRESS START
https://app.box.com/s/w1r560py2bm2wwlbtch9bn7kh1bski2u
Now it will Test the AP CHECK and will write Boot image to your mobile.
It will take 10 to 15 seconds.
After successfully completion of this test you ll see download mode on your mobile. Or you may see an LG logo with a secure boot massege.
Important...
STEP 6 was not mentioned in orignal thread. I did this at my own and got my result.
6. If you dont see download mode or LG logo after completing step 5 even successfully completion shown ion tool, As in mine case on F160k. Then try step 5 with AP CHIPSET with D1L(MSM8960 RR&G)
rest same selection.
AND PRESS START.
I hope this will resolve your issue. As i did.
7. NOW ITS TIME TO FLASH LATEST KDZ FIRMWARE ACCORDING TO YOUR MoBILE Phone.
.
THATS ALL WHAT I HAVE FOR MY FRIENDS.
IF I HELPED YOU THEN PLZ PRAY FOR ME. THANKS ALOT
Thank you for providing the files! I have a bricked LG LTE2 F160K, which mode should I put the phone be?
My phone can still access download mode, and when I try to start up the tool, it just says "Failed during loading flash programmer"
bro if your download mode is working then you will have to flash kdz of your modal for f160k I think its 20k. you can find the latest kdz many sites. google it lg firmware you can find it on vietnam site lgviet.com
this programe is only for qhsusb_delod mode. no download no recovery state. if you have download mode then kdz is the way to unbrick
Help! "device was not found in dload trying flash programmer" i get this error
What kind of brick you have? Its qhsusb bulk mode. Then this guide will help you
what is "ion took"??
there are no "D1L(MSM8960 RR&G)" in the selection
muzammil457 said:
What kind of brick you have? Its qhsusb bulk mode. Then this guide will help you
Click to expand...
Click to collapse
test completed but my phone didn't enter to download mode
the driver name when i connect my LG is"QHSUSB_QLOAD"
why yu no reply??
Have you installed qualcm drivers first? If no then do it if yes then in board ap choose msm8960 it will work. But if doesnt then there is 1 more 8960 selection try that
Does this method works for a sony xperia ion which has the same problem????
ahamedlaheer said:
Does this method works for a sony xperia ion which has the same problem????
Click to expand...
Click to collapse
This programe is for qualcom devices. If your experia is qualcom based then it will work. But u need to find the files to flash doe your modalm I have loaded only f160 system files.
muzammil457 said:
Have you installed qualcm drivers first? If no then do it if yes then in board ap choose msm8960 it will work. But if doesnt then there is 1 more 8960 selection try that
Click to expand...
Click to collapse
yes i install it, i tried the other msm8960 but it doesn't work
Test point to force qhsusb-dload in LG F160s
mcycharles said:
Thank you for providing the files! I have a bricked LG LTE2 F160K, which mode should I put the phone be?
My phone can still access download mode, and when I try to start up the tool, it just says "Failed during loading flash programmer"
Click to expand...
Click to collapse
Dear all,
Can some one provide me the details of test points for LG F160s i want to force it, as m phone in dead alsmost,,,
i will b very thankful
Rizwan
Why u need to do that if u r not in hard brick state?
muzammil457 said:
I brick my lg f160k while flashing wrong kdz on it. It was in no download no recovery mode. Pc was showing qhsusb_dloade 9008. I searched alot over the internet to unbrick it but found nothing except a thread on veitnam site by a veitnamis developer. Thanks to him for this useful thread. With the help of this i unbrick my cell. It was very difficult to understand the thread while in Vietnam's language but i managed to do so with the help of google translator. I thought i should must share it on xda to English community for easy umderstading. Hit thanks if you get your phone back. And many thanks to veitnamis developer too....
1. Download the qualcom drivers and install it from given link.
https://app.box.com/s/5n42md550n4oxne04xttfz788cp0i4i3
Open device manager and ensure that you have correctly installed qualcom 9008 drivers. Remember the com port
2. Download and unzip this folder
https://app.box.com/s/zvvj2v87csuwmv93k7ztzevuiytyd0fi
You shall have a tool Boar Diag v3.99c folder and two folder named S and L.
3.IMPORTANT. You will have to choose folder S For F160K and S and for F160L and LV choose Folder L.
4. Now run the tool.
Check the 2 points on tool
1.Ap check
2.Emmc Test
In Ap chipset choose board
For F160s and F160k
D1L(MSM8960 SKDA)
FOR 160L
D1L(MSM8960 LV)
Select Com Port shown in device manager of your computer.
In TARGET DIR Choose the Folder of Named S or L according to your modal, As i told you earlier in step 3
Rest all should be unchecked
PRESS START
https://app.box.com/s/hr8y0cmzcond0jciemprl5jzr4rllggn
Now test will start and will take 10 seconds to complete
If this test run successfully AP and EMMC should show pass on tool window
5. In this step Now only uncheck
Emmc Test and then check the
Boot Image Restore and select ABOOT from drop down menu.
Only w points Checked.
Ap Check
Boot Img Restor
Rest all should be uncheck the same as in previous step.
PRESS START
https://app.box.com/s/w1r560py2bm2wwlbtch9bn7kh1bski2u
Now it will Test the AP CHECK and will write Boot image to your mobile.
It will take 10 to 15 seconds.
After successfully completion of this test you ll see download mode on your mobile. Or you may see an LG logo with a secure boot massege.
Important...
STEP 6 was not mentioned in orignal thread. I did this at my own and got my result.
6. If you dont see download mode or LG logo after completing step 5 even successfully completion shown ion tool, As in mine case on F160k. Then try step 5 with AP CHIPSET with D1L(MSM8960 RR&G)
rest same selection.
AND PRESS START.
I hope this will resolve your issue. As i did.
7. NOW ITS TIME TO FLASH LATEST KDZ FIRMWARE ACCORDING TO YOUR MoBILE Phone.
. THATS ALL WHAT I HAVE FOR MY FRIENDS.
I have F160L.i tried same as u mention,All proceger complete but no download mode no fastboot mode no LG logo.What to do now?still on qualcomm 9008
Click to expand...
Click to collapse
Hello all
If after restore aboot phone not power on
Need restore all this file: about, Backupgpt, boot, dbi, laf, Primarygpt, recovery, rpm, tz, sdl1, sdl2, sdl3 (one by one, not MIX!!!) and after restore last sdl3 power turn on!
muzammil457 said:
I brick my lg f160k while flashing wrong kdz on it. It was in no download no recovery mode. Pc was showing qhsusb_dloade 9008. I searched alot over the internet to unbrick it but found nothing except a thread on veitnam site by a veitnamis developer. Thanks to him for this useful thread. With the help of this i unbrick my cell. It was very difficult to understand the thread while in Vietnam's language but i managed to do so with the help of google translator. I thought i should must share it on xda to English community for easy umderstading. Hit thanks if you get your phone back. And many thanks to veitnamis developer too....
1. Download the qualcom drivers and install it from given link.
https://app.box.com/s/5n42md550n4oxne04xttfz788cp0i4i3
Open device manager and ensure that you have correctly installed qualcom 9008 drivers. Remember the com port
2. Download and unzip this folder
https://app.box.com/s/zvvj2v87csuwmv93k7ztzevuiytyd0fi
You shall have a tool Boar Diag v3.99c folder and two folder named S and L.
3.IMPORTANT. You will have to choose folder S For F160K and S and for F160L and LV choose Folder L.
4. Now run the tool.
Check the 2 points on tool
1.Ap check
2.Emmc Test
In Ap chipset choose board
For F160s and F160k
D1L(MSM8960 SKDA)
FOR 160L
D1L(MSM8960 LV)
Select Com Port shown in device manager of your computer.
In TARGET DIR Choose the Folder of Named S or L according to your modal, As i told you earlier in step 3
Rest all should be unchecked
PRESS START
https://app.box.com/s/hr8y0cmzcond0jciemprl5jzr4rllggn
Now test will start and will take 10 seconds to complete
If this test run successfully AP and EMMC should show pass on tool window
5. In this step Now only uncheck
Emmc Test and then check the
Boot Image Restore and select ABOOT from drop down menu.
Only w points Checked.
Ap Check
Boot Img Restor
Rest all should be uncheck the same as in previous step.
PRESS START
https://app.box.com/s/w1r560py2bm2wwlbtch9bn7kh1bski2u
Now it will Test the AP CHECK and will write Boot image to your mobile.
It will take 10 to 15 seconds.
After successfully completion of this test you ll see download mode on your mobile. Or you may see an LG logo with a secure boot massege.
Important...
STEP 6 was not mentioned in orignal thread. I did this at my own and got my result.
6. If you dont see download mode or LG logo after completing step 5 even successfully completion shown ion tool, As in mine case on F160k. Then try step 5 with AP CHIPSET with D1L(MSM8960 RR&G)
rest same selection.
AND PRESS START.
I hope this will resolve your issue. As i did.
7. NOW ITS TIME TO FLASH LATEST KDZ FIRMWARE ACCORDING TO YOUR MoBILE Phone.
.
THATS ALL WHAT I HAVE FOR MY FRIENDS.
IF I HELPED YOU THEN PLZ PRAY FOR ME. THANKS ALOT
Click to expand...
Click to collapse
any other link for qualcomm drivers?
Link is fine. U can download it from google.
Need some Help
My phone goes to Service Mode but not in Download mode.
Should i try this method?
And how i can find out my phone is S OR K OR L originally hardware based
Waiting for your answer .
My phone is dead since 1 month
Flash the zip file in the link below in twrp recovery and reboot device.go to my files and there you have it your debrick.img 128mb file.save it to microsd card or pc to save your a** someday.so you dont have to look around anymore for debrick image like a little b***h.
extra tip how to unbrick your note 4 any qualcomm based model.ok I'll try to make simple as i can.
THINGS YOU WILL NEED
1,hard bricked note 4
2,microsd card 16 or 32 gb fully formated
3,windows pc
4,micro usb cable
5,windowd32 disk imager software
6,qualcomm usb drivers
7,brain to concentrate
8,Ok now 1st thing install qualcomm usb drivers to pc and restart pc.
9,install windows32 disk imager software to pc
10,connect your microsd card with flash drive in pc
11,open windows32 disk imager software and upload debrick.img that you made and select write to microsd card.
12,after write to microsd card is finish put your microsd card to bricked note 4.
12,press power button for about 10 seconds and it will came back to life if somehow it didn't turn on take battery off and try again
Download link for windows32 disk imager software.
https://mega.nz/#!KdF0nT5K!UGaWv6geTKtNZXRV1fYsch7YfszoEt7N_lXlJwVp--I
Download qualcomm usb drivers link below
https://mega.nz/#!mZFlSb6L!x5qNX3PetAG9myDRi3RuBAi60h-gx59A_alL0K-wWPM
HIT THUMBS UP IF THIS TUTORIAL SAVE YOUR DEVICE SOMEDAY:good:
PLEASE UPLOAD & SHARE YOUR DEBRICK.IMG IN THIS THREAD SO IT WILL BE VERY HELPFUL FOR MANY USERS.
Download zip file to create debrick.image link below.
https://mega.nz/#!bBU1RDwB!tsRI-0DMFyMcw8SVP1b7_nTyLK6xjiLzS6l1eZcJzxM
Thank you
sorry. how can i create debrick.img file ?
ignore. i managed to find debrick.img from another thread. mine is n910G.
theres a different now at least. when i press power on. it vibrates. however still nothing on the screen.
rkaede said:
sorry. how can i create debrick.img file ?
ignore. i managed to find debrick.img from another thread. mine is n910G.
theres a different now at least. when i press power on. it vibrates. however still nothing on the screen.
Click to expand...
Click to collapse
If it vibrate then debrick.img is working
Just leave the device for 5 minutes after it vvibrates
Iy will take you to tfalsh download mode
There you can flash stock firmware in odin using tflash mode in odin options
Just be patient
Press power button and leave phone for 5 to 10 minutes after it vibrates.
thanks. however after i wait for close to 30min. seems nothing. screen still showing blank. doest that mean the debrick.img its not working ?
rkaede said:
thanks. however after i wait for close to 30min. seems nothing. screen still showing blank. doest that mean the debrick.img its not working ?
Click to expand...
Click to collapse
Yes try another debrick image
And make sure debrick should be made from same bootloader as your last bl before bricked cuz if debrick image made from 6.0.1 bl and you ware on 5.1.1 bl then it won't work.you must use same os debrick.img as your last bl.
Hope I won't need it but thanks a lot!
Trex888 said:
Yes try another debrick image
And make sure debrick should be made from same bootloader as your last bl before bricked cuz if debrick image made from 6.0.1 bl and you ware on 5.1.1 bl then it won't work.you must use same os debrick.img as your last bl.
Click to expand...
Click to collapse
thank you. i will check on that thread what is the BL of that debrick.img
i remember it was on 6.0.1
create debrick image
can someone help me how can i create debrick image using partial sys file on step by step tutorial? i have 2 phones hardbricked like galaxy grand neo plus GTI9060i
and galaxy mega GTI9152
because i dont know how to create for my own or would someone provide me the link for image files for my 2 hardbrick phones? i hope this is a miracle to save my phone i just stucked up weeks ago
can it work on all samsung devices
N910p debrick
anybody here have SM-N910P debrick image?
I will search but I would love a link for debrick.img. for N910G. I see some earlier found one..
SAMSUNG NOTE 4 (n910F)Sympthom:
No Vibration, no image, Dead.Hello, i read a lot of foruns and many solutions, but the one i have chosen to persist was the called microSDcard solution and
because it was the way at first the phone reacted by vibrating. But there was no image or any activity on the screen.
Solution/Worked for me:You need to create a microSD card (i used 16Gb SDHC Kingston) with a bootable image placed on a file called "SD4GB.WinDI.img" you can download.
()
- Download "Win32diskImager" and when it finish installing execute it as Admin
- Select the image file "SD4GB.WinDI", choose the MicroSD letter on 'device' and select 'write' option to start writing the microSD card with the image.
- After you need to place the microSD card on the faulty n910F but no need to connect it for now to the computer.
- With the microSD card and the battery placed you can try to make the "Download Mode" sequence and see if it enters on "Download Mode".
If it doesn´t, like it happened to me, my solution was to take out the memory card and the battery for a few seconds, placed the battery and the microSD card
into the n910F again and pressed the power button and the "Down Volume", wich will make it vibrate with no image. Let the phone rest for a few hours without
removing the battery, the microSD card, do not touch in any buttons. After waiting a few hours the first thing you do its to make the "Download Mode" sequence.
- After enter in "Download Mode" connect it to Odin and flash it with option 'nand erase all' cheked also.
- I had to flash it more than once in Odin because the system update didn't went well, and for that booting in "Recovery Mode" and restoring factory and cache solved the problem. Easy it was not enter "Recovery Mode".
I believe it is the emmc memory chip wich heats to much and looses the content of partitions.
When i say a few hours for me i waited to the next morning and it entered "Download Mode". I flashed it, made the factory reset and it booted well in the many times i tried.No need to place download links, Google the file names i gave and the firmware for the n910F
Hope it works for you all also
Firstly, I want to say ‘thankyou’ to pranaay saini and dr.faramroze. u guys are first man who post topic guide root and build specialy TWRP for Moto E3 Power. And now, I want to share my story about my process ‘rooting Moto E3 Power’ LoL :
*Note:
1/ Im a newbie, not a specialist about android phone or technician mobile. I just a person who curious ‘rooting android’ to make my phone can delete almost factory app not neccesary.LoL. Truly, I want to cheat mobile game =)).
2/ I had successful root HTC One M7 before, so Let’s see me have a little exp for Rooting . Then own the new Moto E3 Power and I want do the same HTC .
*My story:
I bought the new E3 Power on online store and Im going to root it. Unluckily, I forgot to ‘fastboot format userdata’ and this phone gonna ‘bootloop’ :v. I bring it to fix in small repair phone center (I already give them the stock rom), hope they can flash rom stock but they turn my phone into ‘hard bricked mode’ :v, less well they format S/N @@.
That’s a awful time in my life =)), I sent it back to store. Luckily, they accept to fix it cause I just used it for 2 days (actually I told them it was factory error) and maybe they believe it true ‘opsss! So sorry’.
After my phone fixed, I root it again, and this time I did really carefully so ‘Your device has rooted’ Bravo! =)). And ‘Peaceful time’ long last 4months, I just install SDMaid and run Luckypatcher to crack SDMaid FREE up to SDMaid PRO, and used SDMaid to cleanup the phone, then my phone run to error ‘com.android.phone had stoped’, and I also find many ways to fix this problem, almost solution on the internet I have try but it’s not working, the finnally option, I chose to ‘reset phone to factory’ . OOOPS! My phone got ‘Soft bricked’ =.=,unfortunately I had deleted file TWRP backup @@, then I tried to flash stock rom thought TWRP but it error =.=. At this moment, I think ‘prehap I bring it to store fix it again?’ . NOPE! Im looking on the internet to find out solution to fix it (just a few days before I write this topic), finally only way to fix that is ‘SP Flash Tool’ =)), and it work! .
*So it’s all my story when I come to E3 GOD Power =)). Sorry if it so drammatic and bad english :”>. U guys can skip that and go to Main Problem here:
== How to root Moto E3 Power (XT1706) ==
Plz follow step by step if u are new guys like me xD! (Picture guide bellow)
1/ Prepare: ADB (or minimal ADB) and ADB driver on ur PC (u can search on XDA forum to get link download – I recommend use minimal ADB).
2/ Get TWRP recovery and SuperSU from this link:
https://forum.xda-developers.com/showpost.php?p=69311942&postcount=22
copy file SuperSU to SDcard.
3/ On your phone, go to Setting > Choose About phone > roll down to last line > tap many times to set u up to Developer > then back so now u can see ‘Developer options’ line > go into it > swipe ON OEM Unlocking and USB Debugging.
4/ Now turn off power, after screen off hold Power button and Up Volume to boot ur phone into ‘fastboot mode’.
5/ Connect ur phone to PC and open ADB u install before (open ADB as administrator)
6/ Copy file TWRP recovery (*.img) u have download into folder ADB u install before. U can rename it to remember and type on ADB easier. (to me: rename it to recoverymoto.img)
7/ Execute the following comand on ADB:
- ‘fastboot devices’ >> its show u ur device connected to PC or not. If not, plz check adb driver.
- ‘fastboot oem unlock’ >> now on ur display phone have announce unlock YES/NO? follow instruction on display phone. YES to unlock.
- ‘fastboot format userdata’ >> make sure u do this command cause if not after u flash TWRP recovery and reboot system u gonna to stuck boot or boot loop.
- ‘fastboot flash recovery recovery.img’ >> its change Default recovery to TWRP recovery.
Well done! Now u successful to install TWRP.
8/ Now hold Power button and Up Volume to boot ur phone into ‘fastboot mode’ but not choose Fasboot mode, choose Recovery mode. It gonna turn into TWRP recovery display.
9/ Last step. In TWRP working display > choose Install > Select microSD > then u see file SuperSU in SDcard u copy in step 2 > choose file SuperSU and install it > after all done, reboot system and ENJOY ‘Your device has rooted’ .
*Note: If u reboot, it stuck at Moto logo, or boot loop. Plz Redo Step 4 to Step 9. If not, u need to comment and me and E3 power brother will help u
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
== How to unbricked Moto E3 Power (XT1706) ==
Plz follow step by step (Picture guide bellow)
1/ Prepare Stock ROM and SP Flash tool, u can download on this link and the extract it:
https://firmwarefile.com/lenovo-xt1706?_e_pi_=7,PAGE_ID10,9894486982
(ROM S135 is newest for XT1706)
2/ Prepare MTKdriver (MediaTek driver) for ur PC, u can download on this link:
https://forum.xda-developers.com/elephone-m2/help/windows-10-mtk-vcom-usb-drivers-32-64-t3267033
https://androidmtk.com/download-mtk-usb-all-drivers
3/ After install all, open SPflash tool (dont plugin cable and phone to PC), just open flashtool and WARNING on tab Format, don’t Format if u don’t know how to use for what purpose! Cause if u format ur imei phone has gone :v…and u will find and learn how to use S/N tool or even bring it to change mainboard :v…. So DONT, just focus on tab Dowload.
4/ Choose tab download, select Sccatter-loading file (u extract before). Uncheck Preload. Then click Download (u will see it proccessing).
5/ Then plugin ur cable and phone into PC (*note: remove ur battery, sim card and microSD before plugin). Now u will see SP flash tool regconize ur device and auto flash ROM to ur device. Keep wait for 2~3mins till it show check V green symbol. Now u can plugout cable.
6/ Congratulation! Ur phone back to Factory come out . hold the power button and ENJOY ur phone reborn .
*Note: during time flashing ROM, do not plugout cable.
Thanks for your reading!If u like this,give me 1 Thanks . Welcome all constructive comments to help me edit this topic more complete.
First of all I would like to say that @bopvnn luck is not on your side :silly: second of all , all the work was done by @dr.faramroze I just made the tutorial a bit easier .
pranaay saini said:
First of all I would like to say that @bopvnn luck is not on your side :silly: second of all , all the work was done by @dr.faramroze I just made the tutorial a bit easier .
Click to expand...
Click to collapse
i dont know what u mean "lucky is not on my side" :-?
bopvnn said:
i dont know what u mean "lucky is not on my side" :-?
Click to expand...
Click to collapse
Meaning you have bad luck .
Hey, I see some guys on Youtube that said losing their IMEI after flashing stock rom using SP Flash Tool. How to restore it? The last time I use a Mediatek Device it was an Android One.
Removing battery wont help ,
bopvnn said:
Firstly, I want to say ‘thankyou’ to pranaay saini and dr.faramroze. u guys are first man who post topic guide root and build specialy TWRP for Moto E3 Power. And now, I want to share my story about my process ‘rooting Moto E3 Power’ LoL :
*Note:
1/ Im a newbie, not a specialist about android phone or technician mobile. I just a person who curious ‘rooting android’ to make my phone can delete almost factory app not neccesary.LoL. Truly, I want to cheat mobile game =)).
2/ I had successful root HTC One M7 before, so Let’s see me have a little exp for Rooting . Then own the new Moto E3 Power and I want do the same HTC .
*My story:
I bought the new E3 Power on online store and Im going to root it. Unluckily, I forgot to ‘fastboot format userdata’ and this phone gonna ‘bootloop’ :v. I bring it to fix in small repair phone center (I already give them the stock rom), hope they can flash rom stock but they turn my phone into ‘hard bricked mode’ :v, less well they format S/N @@.
That’s a awful time in my life =)), I sent it back to store. Luckily, they accept to fix it cause I just used it for 2 days (actually I told them it was factory error) and maybe they believe it true ‘opsss! So sorry’.
After my phone fixed, I root it again, and this time I did really carefully so ‘Your device has rooted’ Bravo! =)). And ‘Peaceful time’ long last 4months, I just install SDMaid and run Luckypatcher to crack SDMaid FREE up to SDMaid PRO, and used SDMaid to cleanup the phone, then my phone run to error ‘com.android.phone had stoped’, and I also find many ways to fix this problem, almost solution on the internet I have try but it’s not working, the finnally option, I chose to ‘reset phone to factory’ . OOOPS! My phone got ‘Soft bricked’ =.=,unfortunately I had deleted file TWRP backup @@, then I tried to flash stock rom thought TWRP but it error =.=. At this moment, I think ‘prehap I bring it to store fix it again?’ . NOPE! Im looking on the internet to find out solution to fix it (just a few days before I write this topic), finally only way to fix that is ‘SP Flash Tool’ =)), and it work! .
*So it’s all my story when I come to E3 GOD Power =)). Sorry if it so drammatic and bad english :”>. U guys can skip that and go to Main Problem here:
== How to root Moto E3 Power (XT1706) ==
Plz follow step by step if u are new guys like me xD! (Picture guide bellow)
1/ Prepare: ADB (or minimal ADB) and ADB driver on ur PC (u can search on XDA forum to get link download – I recommend use minimal ADB).
2/ Get TWRP recovery and SuperSU from this link:
https://forum.xda-developers.com/showpost.php?p=69311942&postcount=22
copy file SuperSU to SDcard.
3/ On your phone, go to Setting > Choose About phone > roll down to last line > tap many times to set u up to Developer > then back so now u can see ‘Developer options’ line > go into it > swipe ON OEM Unlocking and USB Debugging.
4/ Now turn off power, after screen off hold Power button and Up Volume to boot ur phone into ‘fastboot mode’.
5/ Connect ur phone to PC and open ADB u install before (open ADB as administrator)
6/ Copy file TWRP recovery (*.img) u have download into folder ADB u install before. U can rename it to remember and type on ADB easier. (to me: rename it to recoverymoto.img)
7/ Execute the following comand on ADB:
- ‘fastboot devices’ >> its show u ur device connected to PC or not. If not, plz check adb driver.
- ‘fastboot oem unlock’ >> now on ur display phone have announce unlock YES/NO? follow instruction on display phone. YES to unlock.
- ‘fastboot format userdata’ >> make sure u do this command cause if not after u flash TWRP recovery and reboot system u gonna to stuck boot or boot loop.
- ‘fastboot flash recovery recovery.img’ >> its change Default recovery to TWRP recovery.
Well done! Now u successful to install TWRP.
8/ Now hold Power button and Up Volume to boot ur phone into ‘fastboot mode’ but not choose Fasboot mode, choose Recovery mode. It gonna turn into TWRP recovery display.
9/ Last step. In TWRP working display > choose Install > Select microSD > then u see file SuperSU in SDcard u copy in step 2 > choose file SuperSU and install it > after all done, reboot system and ENJOY ‘Your device has rooted’ .
*Note: If u reboot, it stuck at Moto logo, or boot loop. Plz Redo Step 4 to Step 9. If not, u need to comment and me and E3 power brother will help u
== How to unbricked Moto E3 Power (XT1706) ==
Plz follow step by step (Picture guide bellow)
1/ Prepare Stock ROM and SP Flash tool, u can download on this link and the extract it:
https://firmwarefile.com/lenovo-xt1706?_e_pi_=7,PAGE_ID10,9894486982
(ROM S135 is newest for XT1706)
2/ Prepare MTKdriver (MediaTek driver) for ur PC, u can download on this link:
https://forum.xda-developers.com/elephone-m2/help/windows-10-mtk-vcom-usb-drivers-32-64-t3267033
https://androidmtk.com/download-mtk-usb-all-drivers
3/ After install all, open SPflash tool (dont plugin cable and phone to PC), just open flashtool and WARNING on tab Format, don’t Format if u don’t know how to use for what purpose! Cause if u format ur imei phone has gone :v…and u will find and learn how to use S/N tool or even bring it to change mainboard :v…. So DONT, just focus on tab Dowload.
4/ Choose tab download, select Sccatter-loading file (u extract before). Uncheck Preload. Then click Download (u will see it proccessing).
5/ Then plugin ur cable and phone into PC (*note: remove ur battery, sim card and microSD before plugin). Now u will see SP flash tool regconize ur device and auto flash ROM to ur device. Keep wait for 2~3mins till it show check V green symbol. Now u can plugout cable.
6/ Congratulation! Ur phone back to Factory come out . hold the power button and ENJOY ur phone reborn .
*Note: during time flashing ROM, do not plugout cable.
Thanks for your reading!If u like this,give me 1 Thanks . Welcome all constructive comments to help me edit this topic more complete.
Click to expand...
Click to collapse
everything you said is right except for you have to keep the battery inside and the phone switched
this will help
https://www.youtube.com/watch?v=W-bBhe3kp_8&t=327s
Will root will run on xt1700?
As in the title - Will the TWRP work with the XT1700?
Alcatraz_91 said:
everything you said is right except for you have to keep the battery inside and the phone switched
this will help
&t=327s
Click to expand...
Click to collapse
Bro my phone is vibrating and showing Moto logo and again vibrating and showing Moto logo...so I'm thinking that my phone is soft bricked after flashing twrp 3.1.1
When I try to flash stock using sp flash tool some error is showing 0*00... Will u plzzz help to get back my device..:crying::crying:
My internal storage is about nill...
But it is showing about 14 GB and the actual storage is now 774 mb....how to format it...I'm unable to format it with twrp plzzz help...it is showing storage is running out....plzzzzzz help me....
Manoj Kumar 9779 said:
My internal storage is about nill...
But it is showing about 14 GB and the actual storage is now 774 mb....how to format it...I'm unable to format it with twrp plzzz help...it is showing storage is running out....plzzzzzz help me....
Click to expand...
Click to collapse
Please do not private message me asking for help/assistance with your problems.
I will help anyone if asked correctly, in the correct way and in the correct place.
I will not answer to demanding messages or messages giving no information what so ever.
I'm a typical user, not a helpdesk.
You question is answered in this thread and the Q and A section.
Not able to roote3 power with build s144
Hi,
I have moto e3 power with build number xt1706_s144_170915_row. When i am rooting and installing twrp through fastboot method, after rooting the phone goes in bootloop. The same issue was happening with build s143, however i was able to successfully root for previous build s141. I am following the same method but failing now. Any help will be great
It's my first phone that I will root (moto e3 power)
But the main problem is that, I can't unlock the bootloader , i have used adb driver but after the "fastboot devices" command , my phone's starts in fastboot mode but the connection with my PC is lost. , so please give me the link of the minimal adb and the other moto e3 power driver that you have used to unlock
Jackyhost said:
It's my first phone that I will root (moto e3 power)
But the main problem is that, I can't unlock the bootloader , i have used adb driver but after the "fastboot devices" command , my phone's starts in fastboot mode but the connection with my PC is lost. , so please give me the link of the minimal adb and the other moto e3 power driver that you have used to unlock
Click to expand...
Click to collapse
STOCK ROM INSTALLATION WITH TWRP RECOVERY
Check this video
Without wiping your imei no flash stock rom
This method is find by me please share to others
:good:
---------- Post added at 06:06 PM ---------- Previous post was at 06:05 PM ----------
jigar191089 said:
Hi,
I have moto e3 power with build number xt1706_s144_170915_row. When i am rooting and installing twrp through fastboot method, after rooting the phone goes in bootloop. The same issue was happening with build s143, however i was able to successfully root for previous build s141. I am following the same method but failing now. Any help will be great
Click to expand...
Click to collapse
STOCK ROM INSTALLATION WITH TWRP RECOVERY
Check this video
Without wiping your imei no flash stock rom
This method is find by me please share to others
:good:
Note :-
It works only on S135 and S141
It does not work with S143 and S144
I don't know why
hey 'fastboot format userdata' command not working.. it says "Createprocess failed: system cannot find file specified. (2) cannot generate image for userdate" Kindly help I am noobie
kunal0303 said:
hey 'fastboot format userdata' command not working.. it says "Createprocess failed: system cannot find file specified. (2) cannot generate image for userdate" Kindly help I am noobie
Click to expand...
Click to collapse
use this adb... i too had the same issue......... it worked for me.....
https://forum.xda-developers.com/showthread.php?t=2588979
HELP!!!
i cant execute "fastboot reset userdata" it shows "cant find file specified" please help someone
bopvnn said:
Firstly, I want to say ‘thankyou’ to pranaay saini and dr.faramroze. u guys are first man who post topic guide root and build specialy TWRP for Moto E3 Power. And now, I want to share my story about my process ‘rooting Moto E3 Power’ LoL :
*Note:
1/ Im a newbie, not a specialist about android phone or technician mobile. I just a person who curious ‘rooting android’ to make my phone can delete almost factory app not neccesary.LoL. Truly, I want to cheat mobile game =)).
2/ I had successful root HTC One M7 before, so Let’s see me have a little exp for Rooting . Then own the new Moto E3 Power and I want do the same HTC .
*My story:
I bought the new E3 Power on online store and Im going to root it. Unluckily, I forgot to ‘fastboot format userdata’ and this phone gonna ‘bootloop’ :v. I bring it to fix in small repair phone center (I already give them the stock rom), hope they can flash rom stock but they turn my phone into ‘hard bricked mode’ :v, less well they format S/N @@.
That’s a awful time in my life =)), I sent it back to store. Luckily, they accept to fix it cause I just used it for 2 days (actually I told them it was factory error) and maybe they believe it true ‘opsss! So sorry’.
After my phone fixed, I root it again, and this time I did really carefully so ‘Your device has rooted’ Bravo! =)). And ‘Peaceful time’ long last 4months, I just install SDMaid and run Luckypatcher to crack SDMaid FREE up to SDMaid PRO, and used SDMaid to cleanup the phone, then my phone run to error ‘com.android.phone had stoped’, and I also find many ways to fix this problem, almost solution on the internet I have try but it’s not working, the finnally option, I chose to ‘reset phone to factory’ . OOOPS! My phone got ‘Soft bricked’ =.=,unfortunately I had deleted file TWRP backup @@, then I tried to flash stock rom thought TWRP but it error =.=. At this moment, I think ‘prehap I bring it to store fix it again?’ . NOPE! Im looking on the internet to find out solution to fix it (just a few days before I write this topic), finally only way to fix that is ‘SP Flash Tool’ =)), and it work! .
*So it’s all my story when I come to E3 GOD Power =)). Sorry if it so drammatic and bad english :”>. U guys can skip that and go to Main Problem here:
== How to root Moto E3 Power (XT1706) ==
Plz follow step by step if u are new guys like me xD! (Picture guide bellow)
1/ Prepare: ADB (or minimal ADB) and ADB driver on ur PC (u can search on XDA forum to get link download – I recommend use minimal ADB).
2/ Get TWRP recovery and SuperSU from this link:
https://forum.xda-developers.com/showpost.php?p=69311942&postcount=22
copy file SuperSU to SDcard.
3/ On your phone, go to Setting > Choose About phone > roll down to last line > tap many times to set u up to Developer > then back so now u can see ‘Developer options’ line > go into it > swipe ON OEM Unlocking and USB Debugging.
4/ Now turn off power, after screen off hold Power button and Up Volume to boot ur phone into ‘fastboot mode’.
5/ Connect ur phone to PC and open ADB u install before (open ADB as administrator)
6/ Copy file TWRP recovery (*.img) u have download into folder ADB u install before. U can rename it to remember and type on ADB easier. (to me: rename it to recoverymoto.img)
7/ Execute the following comand on ADB:
- ‘fastboot devices’ >> its show u ur device connected to PC or not. If not, plz check adb driver.
- ‘fastboot oem unlock’ >> now on ur display phone have announce unlock YES/NO? follow instruction on display phone. YES to unlock.
- ‘fastboot format userdata’ >> make sure u do this command cause if not after u flash TWRP recovery and reboot system u gonna to stuck boot or boot loop.
- ‘fastboot flash recovery recovery.img’ >> its change Default recovery to TWRP recovery.
Well done! Now u successful to install TWRP.
8/ Now hold Power button and Up Volume to boot ur phone into ‘fastboot mode’ but not choose Fasboot mode, choose Recovery mode. It gonna turn into TWRP recovery display.
9/ Last step. In TWRP working display > choose Install > Select microSD > then u see file SuperSU in SDcard u copy in step 2 > choose file SuperSU and install it > after all done, reboot system and ENJOY ‘Your device has rooted’ .
*Note: If u reboot, it stuck at Moto logo, or boot loop. Plz Redo Step 4 to Step 9. If not, u need to comment and me and E3 power brother will help u
== How to unbricked Moto E3 Power (XT1706) ==
Plz follow step by step (Picture guide bellow)
1/ Prepare Stock ROM and SP Flash tool, u can download on this link and the extract it:
https://firmwarefile.com/lenovo-xt1706?_e_pi_=7,PAGE_ID10,9894486982
(ROM S135 is newest for XT1706)
2/ Prepare MTKdriver (MediaTek driver) for ur PC, u can download on this link:
https://forum.xda-developers.com/elephone-m2/help/windows-10-mtk-vcom-usb-drivers-32-64-t3267033
https://androidmtk.com/download-mtk-usb-all-drivers
3/ After install all, open SPflash tool (dont plugin cable and phone to PC), just open flashtool and WARNING on tab Format, don’t Format if u don’t know how to use for what purpose! Cause if u format ur imei phone has gone :v…and u will find and learn how to use S/N tool or even bring it to change mainboard :v…. So DONT, just focus on tab Dowload.
4/ Choose tab download, select Sccatter-loading file (u extract before). Uncheck Preload. Then click Download (u will see it proccessing).
5/ Then plugin ur cable and phone into PC (*note: remove ur battery, sim card and microSD before plugin). Now u will see SP flash tool regconize ur device and auto flash ROM to ur device. Keep wait for 2~3mins till it show check V green symbol. Now u can plugout cable.
6/ Congratulation! Ur phone back to Factory come out . hold the power button and ENJOY ur phone reborn .
*Note: during time flashing ROM, do not plugout cable.
Thanks for your reading!If u like this,give me 1 Thanks . Welcome all constructive comments to help me edit this topic more complete.
Click to expand...
Click to collapse
From where i can download fastboot file??
bopvnn said:
Firstly, I want to say ‘thankyou’ to pranaay saini and dr.faramroze. u guys are first man who post topic guide root and build specialy TWRP for Moto E3 Power. And now, I want to share my story about my process ‘rooting Moto E3 Power’ LoL :
*Note:
1/ Im a newbie, not a specialist about android phone or technician mobile. I just a person who curious ‘rooting android’ to make my phone can delete almost factory app not neccesary.LoL. Truly, I want to cheat mobile game =)).
2/ I had successful root HTC One M7 before, so Let’s see me have a little exp for Rooting . Then own the new Moto E3 Power and I want do the same HTC .
*My story:
I bought the new E3 Power on online store and Im going to root it. Unluckily, I forgot to ‘fastboot format userdata’ and this phone gonna ‘bootloop’ :v. I bring it to fix in small repair phone center (I already give them the stock rom), hope they can flash rom stock but they turn my phone into ‘hard bricked mode’ :v, less well they format S/N @@.
That’s a awful time in my life =)), I sent it back to store. Luckily, they accept to fix it cause I just used it for 2 days (actually I told them it was factory error) and maybe they believe it true ‘opsss! So sorry’.
After my phone fixed, I root it again, and this time I did really carefully so ‘Your device has rooted’ Bravo! =)). And ‘Peaceful time’ long last 4months, I just install SDMaid and run Luckypatcher to crack SDMaid FREE up to SDMaid PRO, and used SDMaid to cleanup the phone, then my phone run to error ‘com.android.phone had stoped’, and I also find many ways to fix this problem, almost solution on the internet I have try but it’s not working, the finnally option, I chose to ‘reset phone to factory’ . OOOPS! My phone got ‘Soft bricked’ =.=,unfortunately I had deleted file TWRP backup @@, then I tried to flash stock rom thought TWRP but it error =.=. At this moment, I think ‘prehap I bring it to store fix it again?’ . NOPE! Im looking on the internet to find out solution to fix it (just a few days before I write this topic), finally only way to fix that is ‘SP Flash Tool’ =)), and it work! .
*So it’s all my story when I come to E3 GOD Power =)). Sorry if it so drammatic and bad english :”>. U guys can skip that and go to Main Problem here:
== How to root Moto E3 Power (XT1706) ==
Plz follow step by step if u are new guys like me xD! (Picture guide bellow)
1/ Prepare: ADB (or minimal ADB) and ADB driver on ur PC (u can search on XDA forum to get link download – I recommend use minimal ADB).
2/ Get TWRP recovery and SuperSU from this link:
https://forum.xda-developers.com/showpost.php?p=69311942&postcount=22
copy file SuperSU to SDcard.
3/ On your phone, go to Setting > Choose About phone > roll down to last line > tap many times to set u up to Developer > then back so now u can see ‘Developer options’ line > go into it > swipe ON OEM Unlocking and USB Debugging.
4/ Now turn off power, after screen off hold Power button and Up Volume to boot ur phone into ‘fastboot mode’.
5/ Connect ur phone to PC and open ADB u install before (open ADB as administrator)
6/ Copy file TWRP recovery (*.img) u have download into folder ADB u install before. U can rename it to remember and type on ADB easier. (to me: rename it to recoverymoto.img)
7/ Execute the following comand on ADB:
- ‘fastboot devices’ >> its show u ur device connected to PC or not. If not, plz check adb driver.
- ‘fastboot oem unlock’ >> now on ur display phone have announce unlock YES/NO? follow instruction on display phone. YES to unlock.
- ‘fastboot format userdata’ >> make sure u do this command cause if not after u flash TWRP recovery and reboot system u gonna to stuck boot or boot loop.
- ‘fastboot flash recovery recovery.img’ >> its change Default recovery to TWRP recovery.
Well done! Now u successful to install TWRP.
8/ Now hold Power button and Up Volume to boot ur phone into ‘fastboot mode’ but not choose Fasboot mode, choose Recovery mode. It gonna turn into TWRP recovery display.
9/ Last step. In TWRP working display > choose Install > Select microSD > then u see file SuperSU in SDcard u copy in step 2 > choose file SuperSU and install it > after all done, reboot system and ENJOY ‘Your device has rooted’ .
*Note: If u reboot, it stuck at Moto logo, or boot loop. Plz Redo Step 4 to Step 9. If not, u need to comment and me and E3 power brother will help u
== How to unbricked Moto E3 Power (XT1706) ==
Plz follow step by step (Picture guide bellow)
1/ Prepare Stock ROM and SP Flash tool, u can download on this link and the extract it:
https://firmwarefile.com/lenovo-xt1706?_e_pi_=7,PAGE_ID10,9894486982
(ROM S135 is newest for XT1706)
2/ Prepare MTKdriver (MediaTek driver) for ur PC, u can download on this link:
https://forum.xda-developers.com/elephone-m2/help/windows-10-mtk-vcom-usb-drivers-32-64-t3267033
https://androidmtk.com/download-mtk-usb-all-drivers
3/ After install all, open SPflash tool (dont plugin cable and phone to PC), just open flashtool and WARNING on tab Format, don’t Format if u don’t know how to use for what purpose! Cause if u format ur imei phone has gone :v…and u will find and learn how to use S/N tool or even bring it to change mainboard :v…. So DONT, just focus on tab Dowload.
4/ Choose tab download, select Sccatter-loading file (u extract before). Uncheck Preload. Then click Download (u will see it proccessing).
5/ Then plugin ur cable and phone into PC (*note: remove ur battery, sim card and microSD before plugin). Now u will see SP flash tool regconize ur device and auto flash ROM to ur device. Keep wait for 2~3mins till it show check V green symbol. Now u can plugout cable.
6/ Congratulation! Ur phone back to Factory come out . hold the power button and ENJOY ur phone reborn .
*Note: during time flashing ROM, do not plugout cable.
Thanks for your reading!If u like this,give me 1 Thanks . Welcome all constructive comments to help me edit this topic more complete.
Click to expand...
Click to collapse
Awesome post brother! I only wish I had simply read this post before messing up so much with my phone. Actually, I was messing with some magisk module (edxposed) whick bricked my device and got me stuck at a bootloop and with no recovery partition at all. (It erased my TWRP). So I used the sp flash tool and formatted the whole flash (at that time, I hadn't read this post of yours). Then I flashed my entire firmware back via the sp flash tool. So I thought that now my problem was fixed. But when I switched on my phone I saw my phone's IMEI Number gone! And the sim not working and showing invalid IMEI message. So I tried to find a fix on the internet and I found 2 solutions. First was using an app which requires the phone to support some mtk engineering mode. I followed the instructions and realised that maybe our phone Moto E3 Power doesn't support this mode. So I switched to the second solution, which required root access. So then I set off for rooting my newly unbricked phone. But I again did some mistakes:
1.) Allowed usb debugging and OEM unlocking in my phone's developer options in settings.
2.) I installed minimal ADB v1.4.3 on a windows 10 computer. Checked my phone's connection with the PC via ADB command adb devices. It worked showing some error initially (daemon not started.... Starting daemon...) and then showing some hex code signifying my device's successful connection with the PC.
3.) Used ADB command adb reboot bootloader to boot into fastboot mode. It worked too.
3.) Used fastboot command fastboot devices to check if my device is still being recognised as connected to the pc. Here came an error (the command didn't return any hex code like the adb command adb devices did. So I googled a solution which involves updating the "Android ADB interface" to "Android Bootloader interface" in the "Android device" submenu of the "Device Manager" window of the "control panel" of the pc, by updating its drivers using the "latest windows usb drivers" 8mb file which could be found very easily on the internet (searching solution for fastboot device drivers update on Google). {*Note: If you hadn't installed beforehand, any adb and fastboot drivers at all, then you will see "Other devices" submenu instead of the "Android device" submenu in the device manager window.
Also, you compulsively need to be in fastboot mode with your device attached to pc, in order to see this "other devices" submenu.} So now the fastboot devices command started working by showing the hex code like adb devices command did.
4.) Used fastboot oem unlock command to unlock the phone's bootloader. Pressed the volume up button of my phone as instructed by the warning message on my phone's screen. Unlock flow started in the minimal adb window in my pc. Finished successfully within 9-13 seconds. Another mistake now, after unlocking the bootloader, I forgot to format userdata.. Actually I didn't know about the fastboot format userdata command. I thought the fastboot -w reboot is the only way to format userdata (which wasn't working for me). Unaware of the fact that now I was going to experience a bootloop during rebooting my phone, I continued with the further steps.
5.) Used fastboot flash recovery recovery.img command to flash the unofficial twrp img which I had already placed in the minimal adb folder and renamed to recovery.img I used unofficial twrp v3.1.1 (by moderator) [which was working perfectly earlier on my phone] {link at bottom}. Successfully finished this step too. [You can use either of the two twrp: Dr. Faramroze (link provided by op) or moderator (link provided by me). Both are working fine]
6.) Used the fastboot reboot command (although it never works for me). It shows finished in the minimal adb cmd screen but the phone doesn't reboot. So I manually unplugged the device. Removed and reinserted the battery.
7.) Now rebooted to recovery screen and found the unofficial twrp successfully installed. [ Warning: After the 6th step, don't reboot your phone normally. Instead, boot into the fastboot window [hold power + vol. up] and select the boot into recovery option. This is required only for the first boot up process or else if you do a normal boot during the first boot, the stock recovery replaces our recently flashed custom recovery..
8.) Upon entering the twrp recovery during the first boot, I installed the magisk v19.3 zip I had in my external SD card. It's not necessary to root your phone right now, you may even do it later by simply rebooting from within the twrp, and later on entering recovery after your phone is all set and working and when you're free from other hassles. But I went for rooting during the first boot. And encountered an error something like: "Cannot mount data(0mb)" at the second last line. So, I could not root my phone. So I decided to root it later on and currently just have it switched on. So, I went for the reboot option in twrp.
9.) My phone started rebooting and got stuck at the boot screen with the tag Device unlocked at the lower left corner (indicating unlocked bootloader). But this was something familiar to me, I had already dealt with this error the previous time I rooted my phone. The solution was very simple. I just had to flash a no verity-otp-encrypt.zip file {included along with the twrp link} using the twrp recovery and then my device would boot properly, as it did the last time.
10.) I flashed the no verity-otp-encrypt.zip file from the twrp and got so many red line errors during the flash. (This didn't happen the last time). Every error had the same words, "cannot mount data (0mb)". So I went back to try rebooting again.
11.) Started rebooting again. This time the device didn't get stuck at boot screen, rather it went into a bootloop, rebooting again and again. Now maybe the no verity-otp-encrypt.zip file did its job and my device got free from the stuck at boot screen problem but simultaneously got caught by the bootloop error probably created due to not formatting the userdata after unlocking the bootloader. Or maybe the "cannot mount data (0mb) just ruined up my phone. Whatever the cause be, I just went for reflashing the entire firmware via the sp flash tool and temporarily forgetting all the bootloader unlocking, custom recovery, rooting, etc and live with an invalid IMEI phone without a working sim, until I find a solution on the internet.
12.) And then, I ended up here on this thread leaving my experience, and learning my mistakes from the OP's post. Very soon I will depart for the cyber cafe to try again without any mistakes this time.
At last thanks for this awesome thread.
And yes here's the link for the unofficial twrp 3.1.1 (by moderator) & the no verity-otp-encrypt.zip file:
https://drive.google.com/folderview?id=1-CHJtDUyPH1CJHebhKsUJz8SzKJAcDbv
---------- Post added at 12:56 PM ---------- Previous post was at 12:41 PM ----------
smug_loner said:
From where i can download fastboot file??
Click to expand...
Click to collapse
Search Google for "Moto E3 power firmware flash file" and you will come across websites providing the flash file. The file would have a name like "Motorola_Moto_E3_Power_XT1706_MT6735M_S135_161108_6.0.1.zip". The "S135" over here is the firmware version and will vary upon the version uploaded by the site. The latest version as of today is S152_190315. I somehow managed to download a S151 file and I forgot where I downloaded it from. But you can still go for older firmware versions, and then when you're done with all the flashing and rooting and all that and your phone starts up without any error, you can go for OTA updates from within the settings>about phone>system update.
bopvnn said:
== How to unbricked Moto E3 Power (XT1706) ==
Plz follow step by step (Picture guide bellow)
1/ Prepare Stock ROM and SP Flash tool, u can download on this link and the extract it:
https://firmwarefile.com/lenovo-xt1706?_e_pi_=7,PAGE_ID10,9894486982
(ROM S135 is newest for XT1706)
Click to expand...
Click to collapse
S151 is newest (flash file available for download) for XT1706. [Actually S152 is latest but it's not yet available for download] So you succeeded maybe because you used the older version. Cause a guy commented that he couldn't root the newer versions but could root the older versions.
---------- Post added at 02:32 PM ---------- Previous post was at 02:25 PM ----------
bopvnn said:
4/ Choose tab download, select Sccatter-loading file (u extract before). Uncheck Preload. Then click Download (u will see it proccessing).
Click to expand...
Click to collapse
Is it necessary to uncheck preload? If yes, I think you should highlight it. Anyway, I didn't uncheck preload and the flash successfully worked for me? So what difference does it count for? Please do notify us of its significance.
---------- Post added at 03:03 PM ---------- Previous post was at 02:32 PM ----------
bopvnn said:
4/ Choose tab download, select Sccatter-loading file (u extract before). Uncheck Preload. Then click Download (u will see it proccessing).
5/ Then plugin ur cable and phone into PC (*note: remove ur battery, sim card and microSD before plugin). Now u will see SP flash tool regconize ur device and auto flash ROM to ur device. Keep wait for 2~3mins till it show check V green symbol. Now u can plugout cable.
Click to expand...
Click to collapse
I didn't remove my battery, sim or microsd card and everything worked fine for me. Also, I didn't connect my device to pc after pressing the download button in the sp flash tool. Here's what I did instead:
I kept the sp flash tool ready with all steps. Only pressing the download button remaining. Then I connected my device to the pc. As soon as you hear the device connected sound, press the download button. And the flashing process will start. If you get late in pressing the download button, you will hear another sound of device disconnected. Then you'll have to remove the usb from the device and replug it and go for trying again pressing the download button as soon as you hear the device connected sound.
Here is a step by step guide on how to flash the stock rom with QFIL and by extension any image.
Download and install the Qualcomm drivers from here
Download either of the firmware from here
Download the support files (Firehose/rawprogram0.xml/patch0.xml) here
Extract the firmware and support files to the same folder so you can easily access them like your desktop
Download and install QPST from here
Open the QFIL application (Find it in your start menu)
In the "Select Build Type" field select Flat Build
In the "Select Programmer" field navigate to the folder you extracted the firmware and support files to and select the prog_emmc_firehose_8909.mbn file
Select the "Load XML" button and navigate to the folder you extracted the firmware and support files to and select the rawprogram0.xml and then the patch0.xml when prompted.
Plug in your tablet
Run the following adb command "adb reboot edl" (Now the screen should be blank but the led light should be red)
If the text at the top of the QFIL application says "No Port Available" click the "Select Port..." option and pick your device. If your device isn't showing up there you didn't install the drivers properly.
Click the Download Button to begin flashing your device
So the above explains how to flash everything if you want to flash individual partitions you can edit your rawprogram0.xml to only include the ones you want. (patch0.xml stays the same) I have linked below 2 examples, one of them flashes just a boot.img and one that just flashes the recovery.img. But you aren't limited to those.
Recovery
Boot
Mine just in case
Awesome, thanks for this post! it will really help us in upcoming projects!
Managed to revive my phone using the B12 files but it crashes after completing system.img, I think the problem is userdata.img, my phone boots but I lost the imei and I don't know how to get it back, I'm still trying.
ZTE 971 not recognized by either QPST or QFIL
Thanks for all the detailed instructions. But my ZTE 971 is not visible to either qpst or qfil eventhough the phone shows in windows 8.1. In the Developer Options menu, I noticed Select USB Configuration, RNDIS (USB ethernet) option cannot be enabled. I wonder if this has anything to do with it. OEM unlocking, USB debbugging are already selected. Any suggestions, please? Thanks.
ps. I live in Turkey. I got this phone last year from AT&T and have unlocked the sim.
My PC is not detecting my ZTE MAVEN 3
I have installed all drives but still facing the issue. I am using it on Windows 10.
I flashed the B13 (ZPST tool shows my device as B13) with the QFIL like your guide says and it says all completed successfully and finishes, but now my phone went from only being able to boot EDL + FTM + Recovery, to now booting directly to EDL mode, which obviously means this guide completely screwed up my phone... Thanks.
Mega says that link for the driver is invalid, but the driver is included in your QPST download anyway.
000Nick said:
I flashed the B13 (ZPST tool shows my device as B13) with the QFIL like your guide says and it says all completed successfully and finishes, but now my phone went from only being able to boot EDL + FTM + Recovery, to now booting directly to EDL mode, which obviously means this guide completely screwed up my phone... Thanks.
Click to expand...
Click to collapse
solucionaste hermano
Mod edit:
you solved brother
Click to expand...
Click to collapse
it says qhsusb_bulk when I connect the the software is not working in the mobile and it is stuck at bootloader screen but I used the press both buttons to go to edl mode method and it said in the device manager a device connected with name : qhsusb_bulk
help pls
Hello All.
I am not able to get the following files
rawprogram.xml and patch.xml for LG G8xPlease help me to get this files ASAP as i have hard bricked the mobile, all partitions deleted