Hello, I tried to flash kitkat, I run flashtool and start flashing it but after a while in the middle of flashing it says device disconnected. After that if I connect it to my PC in flashmode it says it has a problem with this device, I can see it in the device manager as an unknown device, device ID is USB/UNKNOWN, fastboot mode says its a sony ADB interface but when I click on it it says it cannot run this device, the device ID is USB/VID_0FCE&PID_0DDE&REV_0100. Is there any way I can repair it? If I try to power up my phone the sony logo appears and it says the software update failed. If I connect it to charger its the same, no battery appears. If someone know how to rescue it please reply, I buyed it yesterday and its already broken
Now I check it on flashtool, after I connect the usb while pressing vol up button it says device connected in fastboot mode but when I click on check current device status it says device status: not found, also get device info says this action can only be done in fastboot mode
And now my PC doesn't notice if something is connected, no device problem pop up, just nothing. Now when I connect it to the charger the led flash red one short time and nothing
EDIT: now i charged it for a while and PC see it again, on charging bootloop with software update failed
Try to flash stock firmware with flashtool and see if it even recognizes it.
Related
Hi,
I faced with a problem what I never seen before:
The device works normally, its on 28.0.A.7.24. I tried to update with PC Companion, it recognized the device as E6533, and offered new software.
Once process started, it downloaded, then phones rebooted instead goes to flash mode. After it (until next reboot), phone completely gone mad:
overheated, not asked for pin code, also IMEI was not available etc.
I tried with Flashtool too, but holding VolumeDown not works. It close to immediatelly drops the boot screen, and never enter flashmode.
Had anyone meet with this issue? How could I fix it?
Fastboot mode is working fine by holding VolumeUp, but flashmode not.
Thanks for help,
Your driver usb may be update,,new pc/laptop come with usb 3
I used FlashTool to flash Sony Z3+ E6553 and now phone cannot power on at all. When I plug in to PC, PC can detect but flashtool cannot flash anymore. The phone was working fine, only has phone lock. Please help revise the phone. Thanks.
citifone said:
I used FlashTool to flash Sony Z3+ E6553 and now phone cannot power on at all. When I plug in to PC, PC can detect but flashtool cannot flash anymore. The phone was working fine, only has phone lock. Please help revise the phone. Thanks.
Click to expand...
Click to collapse
Are you sure that your battery is charged?
Try this: press and hold power and volume up button for 10 seconds and see does the phone vibrate.If vibrate flash again via flashtool.,he should works.
Allek84 said:
Are you sure that your battery is charged?
Try this: press and hold power and volume up button for 10 seconds and see does the phone vibrate.If vibrate flash again via flashtool.,he should works.
Click to expand...
Click to collapse
Battery was fully charged and I've tried that but phone does not response at all to flashtool. When plug in to PC, in device manager under USB controllers, it sees it as SOMC Flash Drive. I think the phone boot is dead.
citifone said:
Battery was fully charged and I've tried that but phone does not response at all to flashtool. When plug in to PC, in device manager under USB controllers, it sees it as SOMC Flash Drive. I think the phone boot is dead.
Click to expand...
Click to collapse
Listen,start flashtool again and hit flash and when pop up windows show press and hold volume down button and connect phone to cable.It should to install so called s1 boot driver(SEMC flash device)Do like I said and see what happends when you connect phone to cable.
If pc install any driver start flashtool again and try to flash again.
Before everything,try to press and hold power and volume up buttoins for more time,about 15 seconds and see did he vibrate.
Allek84 said:
Listen,start flashtool again and hit flash and when pop up windows show press and hold volume down button and connect phone to cable.It should to install so called s1 boot driver(SEMC flash device)Do like I said and see what happends when you connect phone to cable.
If pc install any driver start flashtool again and try to flash again.
Before everything,try to press and hold power and volume up buttoins for more time,about 15 seconds and see did he vibrate.
Click to expand...
Click to collapse
Thanks for your help...The phone was flashed successfully with flash tool with flash file E6553_28.0.A.4.8. After flash done, phone was dead, cannot power on anymore. Now when I tried to flash it again, volume down, insert USB the flashtool show as: Device detected with USB debugging off. It doesn't go to flash mode anymore. I took the back cover off, remove battery connector flex cable and connect it back and try flashing many times but flashtool will not detect phone in flash mode..PC can detect phone because it makes connecting sound on PC but detects as what mode I don't know. In device manager, it doesn't show any device in com port but it shows SOMC Flash Device in USB controllers. I tried to press volume up + power but nothing happened. Once again thanks for your help.
somc flash device means dead boot....its no solution yet for it,sorry
this guy or website promise to repair this dead boot problem via test point look here:
ht_tp://www.vungoc-mobile.com/index.php/unlock/932-repair-boot-unbrick-sony-e6553-xperia-z3
or here
http://www.vungoc-mobile.com/index.php/unlock/932-repair-boot-unbrick-sony-e6553-xperia-z3
citifone said:
Thanks for your help...The phone was flashed successfully with flash tool with flash file E6553_28.0.A.4.8. After flash done, phone was dead, cannot power on anymore. Now when I tried to flash it again, volume down, insert USB the flashtool show as: Device detected with USB debugging off. It doesn't go to flash mode anymore. I took the back cover off, remove battery connector flex cable and connect it back and try flashing many times but flashtool will not detect phone in flash mode..PC can detect phone because it makes connecting sound on PC but detects as what mode I don't know. In device manager, it doesn't show any device in com port but it shows SOMC Flash Device in USB controllers. I tried to press volume up + power but nothing happened. Once again thanks for your help.
Click to expand...
Click to collapse
As I understood, you tried to downgrade. Am I right? I heard that sometimes downgrading causes hard brick. I don't know how to fix it but only option is bringing service.
sone xperia z3+ (E6553) flash after dead
sone xperia z3+ (E6553) flash after dead
sony xperia z3+ e6553 model
flash with this model e6653
it does not start after with it
please help me sir
Hi Guys,
I had a battery draining problem. During the firmware update, device got dead in process of the update.
Battery charge was above 90% during the update.
After replacement of battery. Tired by holding power+vol up & holing vol down. Device is not recognized.
I am trying to install stock ROM. Below are the steps which I have performed so far.
1. Charged the device for overnight (Red LED blinking) & when connected to charger (LED=RED, stable)
2. Installed flash tool, drivers
3. When prompted to connect the device for flashing, i get the below info. For which I tired with different flash-tool versions.
23/051/2016 15:51:13 - INFO - Device connected with USB debugging off
23/051/2016 15:51:13 - INFO - For 2011 devices line, be sure you are not in MTP mode
4. Tired to repair from Sony PC companion suite as well by pressing "volume down button". Device is not recognized when prompted.
Could anyone pls help me on this.
Regards
Sunil
sunil14353 said:
Hi Guys,
I had a battery draining problem. During the firmware update, device got dead in process of the update.
Battery charge was above 90% during the update.
After replacement of battery. Tired by holding power+vol up & holing vol down. Device is not recognized.
I am trying to install stock ROM. Below are the steps which I have performed so far.
1. Charged the device for overnight (Red LED blinking) & when connected to charger (LED=RED, stable)
2. Installed flash tool, drivers
3. When prompted to connect the device for flashing, i get the below info. For which I tired with different flash-tool versions.
23/051/2016 15:51:13 - INFO - Device connected with USB debugging off
23/051/2016 15:51:13 - INFO - For 2011 devices line, be sure you are not in MTP mode
4. Tired to repair from Sony PC companion suite as well by pressing "volume down button". Device is not recognized when prompted.
Could anyone pls help me on this.
Regards
Sunil
Click to expand...
Click to collapse
hi
are you ready to disassemble your xperia?
did you try this ???
look here
http://sony.yt/topic/7324-english-t...oot-in-sony-xperia-z-c6602-c6603-c6606-c6616/
sorry to put a link from another forum.
Hey i'm not exactly sure what you mean by the description, but to enter flash mode you need to turn off the device - then hold down the volume-down key whilst inserting the usb. Keep holding down the volume-down key until you seen some green notification lights flash and you should be in flashmode and ready to flash a FTF. It should also say on flashtool that "Device has entered flashmode" or something like that.
I got my Xperia SP bricked, on boot loop showing Sony logo all over again and red LED turning on and off. I tried getting into the flash mode, but I can do that only for about 10 seconds, after that Flashtool shows "Device disconnected". The LED goes from green to off, to the red with Sony logo for a moment, and then back to the green, showing 100% battery charged icon and Flashtool says "Device connected with USB debugging off". I can't fix it using PC or Xperia Companion. I tried on another computer and got the same result, flash mode works just for a moment. When connected to the PC, it see my phone as "mass storage device". The only thing I can do is get into fastboot, but I have locked bootloader... Please help
then try and get stock kernel and flash through fastboot that should fix problem if not then try going on flashtool and exclude everything exept kernel and when it asks to connect u might get lucky and it flashes it very quick,only other option try downgrading flashtool http://www.flashtool.net/downloads.php pick bottom one
Good evening everyone!
I need help so bad, so urgent!
It was happen when i try to install TWRP on my SONY Xperia SP using an amazing stupid way, using flash boot command coz i cant install twrp using flash recovery command, but i dont know why that fastboot take so long time and just display <waiting for device>. So i decided to remove my USB and plug it once again. Suddenly, my laptop show a notif. "USB not recognized" and the blue LED is gone, then SONY logo appear and start to charging and u can hear connect-"Not recognized"-and disconnect sounds from laptop. But, when the display turn off, it's turn on again, and 5 seconds later u can hear disconnected sounds, then charging stopped. Few later, the logo come again and charging again, and the same thing happend. When i try to charge from the wall charger, it can charging normally, but I CAN'T TURN THE PHONE ON. It's like the power button has been disabled. So i unplug the charger and turn my XSP on, it can boot normally. But when i try to connect to charger, it wont charging. So on my laptop, even my laptop didnt notice any USB, and my XSP didn't show any LED.
Help me to fix this. I can't charge my phone except to turn it off T_T. Pls give me a way out T_T.
Status: Installed AOSP Oreo 8.0.0 huashan, not rooted and no cwm/twrp (this is what i need to install, so i can root my phone, the latest cwm i installed gone after flashing AOSP ROM), cant connect to any USB even in fastboot mode (i've installed the driver).
seems like you got dust in your usb port , it happened to me once , i freaked out real bad. just try clearing it with some needle or stuff , also you might wanna use emma to revert your phone back to its original stock firmware.
AsadXperia said:
seems like you got dust in your usb port , it happened to me once , i freaked out real bad. just try clearing it with some needle or stuff , also you might wanna use emma to revert your phone back to its original stock firmware.
Click to expand...
Click to collapse
what's emma? how to use that?
it's a sony developer tool. You can use it to install original os on your phone , you just need a pc and internet connection , here
https://talk.sonymobile.com/t5/Andr...ony-Flash-tool-for-Xperia-devices/td-p/307318
Also , just save the customization file and delete the rest , download emma sony flash tool from google ( latest version ) copy the customization file after installing it.
After it completes install , run it and wait for it to open , it may take some time during its first run.
Now plug in ur phone , while holding volume down button , you should see green light on bottom , that indicates you're on recovery mode or flashmode. The Emma tool will detect device and start installing original firmware on it.
AsadXperia said:
it's a sony developer tool. You can use it to install original os on your phone , you just need a pc and internet connection , here
Also , just save the customization file and delete the rest , download emma sony flash tool from google ( latest version ) copy the customization file after installing it.
After it completes install , run it and wait for it to open , it may take some time during its first run.
Now plug in ur phone , while holding volume down button , you should see green light on bottom , that indicates you're on recovery mode or flashmode. The Emma tool will detect device and start installing original firmware on it.
Click to expand...
Click to collapse
that was my problem. when i plug my phone in fastboot or bootloader, pc wont detect it, it says "USB not recognized". also when my phone is standby, it wont detect any usb i plugged in, wall charger or usb pc.
i've installed latest driver for XSP, and USB debugging's on.
have you read my first comment? , clear your phone's usb slot and then try replugging , if it fails try it on a different computer , the problems usually with windows 10 as it loses recognizing devices after some fail attempts.