Ok, so I don't have buttons and USB debugging was off. Battery was drained, the phone turned off and now I don't know how to turn it back on. Is there any way through command line?
Put the phone on charge let the battery have some charge in it.
if any case volume down button is working then you can start your device by connecting usb to your device first and then holding down volume button and then connect usb cable to PC (your PC must need adb drivers installed if not then install it first)
test point method should also help but i am not sure though.
I charged the battery but the phone didn't turn on the OS, I can see the battery level only.
Uhm... I don't have buttons at all. I mean physically. They're gone because I broke the buttons' tape [emoji23]
Sent from my Mi A2 Lite using Tapatalk
Related
I appear to be having wired issues related to the USB port as has been previously reported on the Galaxy S2.
When not plugged in to anything, it constantly says it is charging. It will not let me select between USB debugging mode as it says the cable is connected.
Despite it's belief that it is charging, when I actually plug it in to the mains to charge, it doesnt charge!!
If I power off the device, it shuts down correctly, however it will constantly switch between the grey battery icon, then a almost full green one, then off. It then wont allow me to turn on the device. Ive tried plugging it in to the mains (but I guess that as it wont charge this way, this is why it wont let me turn it on this way either) the only way I can boot it up is holding vol up, middle button and power together for 10 seconds or so. It then goes to CWM recover where I can reboot the device
If I plug in a jig, that allows me to connect a USB flash drive, it all seems to work OK. it no longer says it's charging, and i'm able to mount the drive.
The only way I can actually make it charge, is by plugging in to a PC.
Im very careful with my USB connectors, and I can only think that slight dampness may have entered as the phone has been with me in the bathroom during showers.
I dont want to send my phone in for repair, my first plan is to wait it out and hopefully any moisture dries out. Ive tried cleaning the inside of the USB port, but it makes no difference.
If I changed the USB port myself, a) is that a hard task, b) would it solve my issue?
I had a very similar problem with my note.
Solution was to take out the battery and leave the cover off, in a dry p;ace over night. It could definitely be related to dampness in your phone.
Hi all!
I was using my phone (listening to a recording and browsing as far as I remember) and battery was about 50%, then suddenly it turns off by itself. Tried to turn it back on, but still won't turn on so I thought battery just got glitched or something. Did the following after I came home:
1. Charged normally using original HTC charger [few min to multiple hours].
2. Charged normally using a non HTC charger [few min to multiple hours].
3. Plugged in to a computer using original HTC usb cable [few min to multiple hours].
4. Plugged in to a computer using a non HTC usb cable[few min to multiple hours].
5. Tried pressing Vol + and Power Button at the same time.
6. Tried pressing Vol down and Power Button at the same time.
7. Tried presseing Vol up, down and Power Button at the same time.
8. Placed phone under a bright light (light bulb) then tried doing 5, 6 and 7.
9. Placed phone under a bright light while holding Vol up and Power Button.
I tried almost anything, but phone still won't charge. No light indicator coming up and computer won't read the phone when I plug it in to my computer. Used different USB ports and USB cables, everything not working except that the Device Manager reads QHSUSB_DLOAD, which I read that it means my phone is bricked. This was a bit confusing to me because everything were stock. I never even attempted to do custom ROM's or root my phone or whatever else they do with it. I just bought the phone, used it, charge it and that's it. Never dropped it or anything that could damage it.
Please help me with this since I phone's warranty is already up and I needed my files and phone very badly.
Zeeevil said:
Hi all!
I was using my phone (listening to a recording and browsing as far as I remember) and battery was about 50%, then suddenly it turns off by itself. Tried to turn it back on, but still won't turn on so I thought battery just got glitched or something. Did the following after I came home:
1. Charged normally using original HTC charger [few min to multiple hours].
2. Charged normally using a non HTC charger [few min to multiple hours].
3. Plugged in to a computer using original HTC usb cable [few min to multiple hours].
4. Plugged in to a computer using a non HTC usb cable[few min to multiple hours].
5. Tried pressing Vol + and Power Button at the same time.
6. Tried pressing Vol down and Power Button at the same time.
7. Tried presseing Vol up, down and Power Button at the same time.
8. Placed phone under a bright light (light bulb) then tried doing 5, 6 and 7.
9. Placed phone under a bright light while holding Vol up and Power Button.
I tried almost anything, but phone still won't charge. No light indicator coming up and computer won't read the phone when I plug it in to my computer. Used different USB ports and USB cables, everything not working except that the Device Manager reads QHSUSB_DLOAD, which I read that it means my phone is bricked. This was a bit confusing to me because everything were stock. I never even attempted to do custom ROM's or root my phone or whatever else they do with it. I just bought the phone, used it, charge it and that's it. Never dropped it or anything that could damage it.
Please help me with this since I phone's warranty is already up and I needed my files and phone very badly.
Click to expand...
Click to collapse
If your phone was 100% stock and it went itself in qhsusb_dload mode its probably because of an hardware defect and there is nothing you can do. The unbrick project is your only hope but its for devices that entered this mode because the user flashed something wrong, so it will probably not work but you should try it just in case.
Hello. This morning I've turned off the alarm, turned on WIFI and went back to sleep. I can't tell for sure, but I think the battery was low. During the next 2 hours I checked the time several times. I don't remember accepting any OTA. Eventually I got up, tried to check the time and the phone was off. I tried to turn it on, no effect. No matter how many times and for how long I pressed and held the power button, the green LED only flashed for a split second and that's all. I plugged in the charger, and the LED stayed lit -but- there was this barely noticeable flickering. Charged it for about 30, 60, 120 minutes, didn't start plugged or unplugged. I went to work, 8 hours later (phone was unplugged) I tried to turn it on again, this time the LED doesn't even flash, but when charging there is no flickering. No combination of buttons works. Windows doesn't find the device, neither does RSD.
I've never done anything 'custom' to the phone. The last change I made was setting the alarm to turn off by shaking (yesterday, never used this option before).
Is it dead?
Try taking SD card out and holding Vol down and then Power for 20 secs, then let go of Power,
Already done that, nothing. No matter how long I charge it now, after unplugging and pressing power button the LED doesn't even flash. Could it be a battery problem (before its death, it would last for a day)? Is there any way of recovering my data without buying a new one?
Try opening and disconnect battery for a bit.
I'll do that as a last resort, on weekend maybe since I don't have the tools with me. Any other clues?
Nobody knows how to help me?
I'm going to make a factory cable. Will this alone allow me to recover the data? Or if I'll be able to flash the phone, can I recover the data afterwards?
Also, I'm not sure if I understand correctly: does the factory cable recharge the battery or not? Is there a way to recharge it when removed from the phone?
Try to use medfield unbrick script. If You have only green led it seems to be bootloader error so this script should bring Your phone to life or Your phone has broken emmc and You can start looking for a new logic board. Good luck.
I've installed the drivers, but Windows and XFSTK don't recognize my device at all. Factory cable also didn't help. I liked my phone very much. :angel:
Did You enter medfield mode using combination with camera button??
By a combination you mean holding the camera button and connecting the phone to a pc? I tried that.
Disassembe Your phone, pull out battery, push power button for a 10 sec, plug in battery, push camera button and connect USB. If it wont help You I don't see any hope for Your phone.
Well, new option to try is a new hope. I'll try that on the weekend. Could you please be more specific:
1. Pull out the battery.
2. Press the power button and wait 10 seconds.
3. Insert the battery: should I be still holding the power button at this moment?
4. Press the camera button.
5. Plug in the usb cable (factory? regular?) - should I be still holding the power and camera buttons?
Battery trick is only to discharge capacitors. Sometimes even phone is dead it can turn on in some strange mode and then You can't boot it to flash. Thats why You need to pull out battery, push power for a few sec to completely discharge motherboard and just release this button. After that You can just plug in battery and continue normal unbrick process - so hold camera button only and connect regular usb cable.
You can also try reset option instead of pulling battery out. To do that do not disassemble Your phone but just plug in regular USB, when phone starts (green led) hold power and vol- until green led goes off and then quickly start holding only camera button.
I have no more ideas.
Ok, I've tried everything. Nothing brought my phone back to life.
Thanks for all your help.
Hello,
I was transfering some files from my OP3T to my laptop with usb cable, and the screen went freeze-blur and then shut down.
Now it does not turn on, does not vibrate or charging, no led turning on and the pc does not find it anymore. It is dead =/
Do you know why this happened and how to turn it back on?
Thank you in advance
Hi buddy,
This is really strange that your phone is hard bricked after some data transfer.
The only advice I can give is try to search for: "hard bricked oneplus 3(t)" and follow the instruction.
If your phone is not seen as a qualcomm device when you follow the instruction than it could be that you phone is 'dead' by damage from the cable! It's just a guess from my side.
Mnarijnm
Edit: did you tried power + volume up/down?
A battery failure can do that. I would leave it for a few hours and the see if it turns on. If not, try charging it for a few minutes and then try turning it in with the power cable still connected.
Sent from my OnePlus3T using XDA Labs
Try leaving it plugged in for a couple hours, and then holding Power and Home. Weird, but worked for my. Hold it for like 20 seconds or so.
Hello,
thanks for your answers and effort to help me with my bricked phone.
I have managed to find my OP3T on pc under Devices ->ports -> Qualcomm HS USB QDLoader 9008 com3.
Now I am trying to unbrick it with OP3T Unbrick Tool but when I Run MsmDownloadToolV3.0 and press Start , I get a mesaage on 'Communication Status' that say ""Firehose Communication handshake Failed"' and stops, also this message "Sahara communication failed£¬please try again after power off the phone,".
Do you know how to resolve this issue?
Thank you again.
sxizofrano said:
Hello,
I was transfering some files from my OP3T to my laptop with usb cable, and the screen went freeze-blur and then shut down.
Now it does not turn on, does not vibrate or charging, no led turning on and the pc does not find it anymore. It is dead =/
Do you know why this happened and how to turn it back on?
Thank you in advance
Click to expand...
Click to collapse
Try press and hold the power key for like 20 seconds after it vibrates release the power key and press it again when the soft keys light shows up... Hope it'll help.
Make sure your device is properly turned off first of all. You can do that by turning off the device via fastboot menu.
After that, when you are sure device is turned off... make sure to hold 30 seconds... do a little longer even, and plug it in to the USB that is connected to the PC.
I personally did that and it worked well. I also just rebooted my PC and it literally had been on for a couple of seconds, maybe 30 seconds. Started MSM in administrative mode and pressed start. Connected and installation went through.
Had same issues like you before that.
Recently i got my Honor 9 lite and in a few weeks i managed to install openkirin Resurrection remix. all was good till i decided that i was having ram issues so i then found out about project treble.
This is where the original problem started I used the ARM A Decendent rom and i flashed it to a bootloop. whenever i tried to go back to stock or RR i'd have the same thing. i've tried many things but eventually i made a batch file to erase and reflash all of the stock software.
now i made some typos and the kernal didn't flash. now im stuck with a brick that wont turn on. im ****ting myself. im very scared and i desperately need help. im a ****ing idiot.
Atleast when i plug it in my computer detects it as "USB Ser"
UPDATE: i installed some kind of driver on my PC. it now shows up as "HUAWEI USB COM 1.0 (COM 7)"
I'm actively looking for board software to fix this issue. if you are able to obtain it. DM me on telegram: @AmethystLegit
Its for a LLD-L31
+ I cant get into fastboot
Ok power the phone off fully so whilst it is plugged in your computer press and hold the power button till USB item is removed from the device manager now press volume up and plug the USB cable into a charger see if it will boot into recovery mode from there, then download the firmware from that area.
Sent from my LLD-L31 using Tapatalk
hacktrix2006 said:
Ok power the phone off fully so whilst it is plugged in your computer press and hold the power button till USB item is removed from the device manager now press volume up and plug the USB cable into a charger see if it will boot into recovery mode from there, then download the firmware from that area.
Sent from my LLD-L31 using Tapatalk
Click to expand...
Click to collapse
Hmm. i've held the button down but it only restarts. i've had it plugged in for awhile now and windows made a disconnect sound a few times. it hasn't unplugged itself. maybe ill check the device manager once thats happened again. and then ill hold vol up
AmethystLegit said:
Hmm. i've held the button down but it only restarts. i've had it plugged in for awhile now and windows made a disconnect sound a few times. it hasn't unplugged itself. maybe ill check the device manager once thats happened again. and then ill hold vol up
Click to expand...
Click to collapse
It literally just happened. the item is still there. i guess we could run it out of battery
That could be one way or press and hold the power button for 10 seconds whilst disconnected from USB and hold the volume up button then plug the USB in while it's connected to a charger, the only pins needed is the power pins not data pins. volume up trick doesn't work whilst data pins are working I.E connected to PC you must use a phone charger.
Sent from my LLD-L31 using Tapatalk
hacktrix2006 said:
That could be one way or press and hold the power button for 10 seconds whilst disconnected from USB and hold the volume up button then plug the USB in while it's connected to a charger, the only pins needed is the power pins not data pins. volume up trick doesn't work whilst data pins are working I.E connected to PC you must use a phone charger.
Sent from my LLD-L31 using Tapatalk
Click to expand...
Click to collapse
Assuming the cable that came with the phone is a phone charger and not data. its not working. i dont think i have any of such around. ill try running the battery out.
meanwhile im now actively looking for board firmware to try a different method but i've gotten nowhere
The cable with the phone also has the data pins, else how would you transfer your files, please try using the Charger and Volume method like i suggested.